aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/mikrotik
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: Kernel board definition for PowerCloud CR5000Felix Fietkau2015-12-191-0/+1
| | | | | | | | | | | | Kernel part of support for the PowerCloud Systems CR5000. The CR5000 is a dual-band 802.11n wireless router with 8MB flash, 64 MB RAM, (unused in stock firmware) USB 2.0 port, and five port gigabit ethernet switch. The CR5000 was sold as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47940
* ar71xx: Kernel board definition for PowerCloud CR3000Felix Fietkau2015-12-191-0/+1
| | | | | | | | | | | | Kernel part of support for PowerCloud CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM, a four port fast ethernet switch, and a fast ethernet wan port which was sold by PowerCloud Systems as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47939
* ar71xx: Kernel board definition for PowerCloud CAP324Felix Fietkau2015-12-191-0/+1
| | | | | | | | | | | | | | | Kernel part of support for PowerCloud CAP324 Cloud AP. The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for the CloudCommand service for 'cloud' based managment of large numbers access points. The CAP324 is a dual-band 802.11n wireless access point with 16MB flash and 128MB RAM and single gigabit ethernet port. It can be powered via PoE or a power adaptor. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47938
* ar71xx: Build initramfs by default for Mikrotik devicesJohn Crispin2015-11-241-1/+1
| | | | | | Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org> SVN-Revision: 47612
* ar71xx: Add support for AP147-010 reference boardJohn Crispin2015-07-241-0/+1
| | | | | | Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 46457
* ar71xx: microtik: disable all non-microtik boardsJonas Gorski2015-07-051-3/+6
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46191
* ar71xx: add initial support for RB911G-5HPacDGabor Juhos2015-04-071-0/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 45299
* ar71xx: routerboot: add support for extended radio dataGabor Juhos2015-04-071-0/+1
| | | | | | | | | | | | | On newer Mikrotik boards, the radio calibration data is stored differently and uses LZO compression instead of RLE. Update the RouterBOOT helper code to support the new format. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 45297
* ar71xx/mikrotik: disable atnoher two non MikroTik boardsGabor Juhos2015-03-311-0/+2
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 45177
* ar71xx/mikrotik: disable non MikroTik boardsGabor Juhos2015-03-311-0/+32
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 45176
* ar71xx/mikrotik: use correct symbol to disable overlayfsGabor Juhos2015-03-311-1/+1
| | | | | | | | The Kconfig symbol has been changed in 3.18. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 45175
* ar71xx/mikrotik: re-enable 4KiB flash sector eraseGabor Juhos2015-03-301-1/+1
| | | | | | | | | | | The setting has been lost during the transition to 3.18. The CONFIG_M25PXX_PREFER_SMALL_SECTOR_ERASE option is not available anymore, so use CONFIG_MTD_SPI_NOR_USE_4K_SECTORS instead. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 45161
* ar71xx: added support for TL-WA830RE V2John Crispin2014-07-131-0/+1
| | | | | | | | Corrected patch ath79 insted of auth79. Sorry. Signed-off-by: Fredrik Jonson <fredrik@famjonson.se> SVN-Revision: 41596
* ar71xx: Add support for MikroTik RouterBOARD SXT LiteJohn Crispin2014-07-011-0/+1
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD SXT Lite. The new RB911L series is also supported as a result. v2 of this patch fixes the wmac offset to match what is on the sticker. v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com> Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41450
* ar71xx/mikrotik: enable the AT803x PHY driverGabor Juhos2014-04-131-0/+1
| | | | | | | | It will be used on the RB91x boards. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 40508
* ar71xx/mikrotik: enable the 74x164 GPIO driverGabor Juhos2014-02-231-0/+1
| | | | | | | | | That will be used to drive the 74HC595 serial-in/parallel-out 8-bits shift register which can be found on some RouterBOARDs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39702
* ar71xx/mikrotik: enable the GPIO latch driverGabor Juhos2014-02-221-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39698
* ar71xx/mikrotik: enable small sector erase in the m25p80 driverGabor Juhos2014-02-221-0/+1
| | | | | | | | | | | The serial flash devices used on the ROuterBOARDs are supporting 4KiB erase blocks. Enable the small sector erase option in the m25p80 driver to avoid superfluous erase/write of adjacent blocks. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39696
* ar71xx: add initial support for the Mikrotik RB911G/RB912UAG boardsGabor Juhos2013-12-161-0/+2
| | | | | | | | | It is only on RB911G-5HPnD and RB912UAG-5HPnD boards. The LEDs and the USB port is not working yet. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39102
* kernel: remove obsolete yaffs options from target configsGabor Juhos2013-12-161-2/+0
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39085
* ar71xx/mikrotik: disable unused MTD optionsGabor Juhos2013-12-161-0/+8
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39080
* kernel: add missing config optionsHauke Mehrtens2013-11-011-1/+0
| | | | | | | | The buildbots found some new missing config options. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38633
* ar71xx: move subtarget specific features to target.mkGabor Juhos2013-10-301-0/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38600
* ar71xx: disable non Mikrotik boards in the mikrotik subtargetGabor Juhos2013-10-301-0/+82
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38597
* ar71xx: move CONFIG_MTD_NAND_AR934X_HW_ECC option to subtarget configGabor Juhos2013-10-301-0/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38595
* ar71xx: rename 'nand' subtarget to 'mikrotik'Gabor Juhos2013-10-234-0/+74
It is for Mikrotik devices only, rename the subtarget to reflect that. Also fix the wget2nand script to use the new image names. Based on the patch by Stefan Agner: http://patchwork.openwrt.org/patch/4123/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38509