| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
| |
This moves the Meraki MR12 and Meraki MR16 to the new generic target.
Tested and verified working on both devices.
Note that kernel/rootfs images are still generated. This is because they
are used for the inital flashing process due to the fun pace at which
UBoot erases/writes to SPI.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
|
|
|
|
| |
Signed-off-by: Jing Lin <mumuqz@163.com>
|
|
|
|
|
|
|
| |
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
| |
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There is no US firmware for the TL-WA901ND v4 yet, so we'll just
unconditionally set the EU region for now.
This makes LEDE flashable on these devices again. The format of the region
string is slightly different from the one used on the Archer C7 that is
generated by mktplinkfw (the second half of the region string is missing),
but it's similar enough to make it work.
Tested-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the Airtight C-60.
SOC: Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM: 128 MiB
NOR: MX25L3205D 4MiB
NAND: ST Micro NAND 32MiB 3,3V 8-bit
SW-NET: AR8327N (2 Ports)
WLAN1: Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2: Dual-Band AR9300 Rev:4 PCIe Chip
The switch is setup for an accesspoint:
LAN1: (gigabit) is the wan-port.
LAN2: (fast ethernet) is bridged with the br-lan.
Flashing Guide (via initramfs):
1. Connect a PC to the serial port of the C-60.
power up the C-60.
Enter u-boot command prompt:
#> nand erase
#> setenv bootcmd "bootm 0x9f060000"
#> saveenv
#> setenv ipaddr 192.168.1.1
#> setenv netmask 255.255.255.0
#> setenv serverip 192.168.1.100
#> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
#> tftpboot
#> bootm
2. Wait for the C-60 to boot LEDE.
On the root prompt. Enter:
# ubiformat /dev/mtd4
# ubiattach -p /dev/mtd4
3. After that copy the sysupgrade.tar onto the router and run:
# sysupgrade sysupgrade.tar
to flash the image.
Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
| |
Tested on real hardware with r1804.
Signed-off-by: Karl Palsson <karlp@etactica.com>
|
|
|
|
|
|
| |
Signed-off-by: Florian Beier <beier.florian@gmail.com>
[Matthias Schiffer: fix factory image, improve commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
|
| |
Use relocation loader instead of lzma loader.
Tested on D-Link DIR-869 A1.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
| |
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
|
|
|
|
| |
Split seama-factory and seama-sysupgrade into smaller pieces (similar to
the ramips code) to make the image generation more flexible.
Also use standard pad-offset instead of adding a block of zeros at the
beginning of the image that is later cut off again. Standard pad-rootfs can
be used as the seal header doesn't contain an image size or checksum.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
| |
TP-Link uses a different region coding mechanism for IL firmware for the Archer
C7 v2. Instead of of setting the region, they set a different TPLINK_HWREV.
Signed-off-by: Amir Rachum <amir@rachum.com>
|
|
|
|
|
|
|
|
|
| |
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
|
|
|
|
|
|
| |
Remove arbitrary or redundant packages from DEVICE_PACKAGES.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
| |
General convention is to keep U-Boot and radio calibration
data (ART) mtd partitions marked as read-only.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
| |
There are currently two stock firmwares for the TL-WDR3600/4300, a US and
a universal version. Both allow installing images with US region code, so
we don't need to provide multiple images.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
|
|
| |
Simplify modifying some of the images without affecting the others.
While we're at it, also unify the profiles to use := syntax and add "v1" to
the TL-WDR4300 name to make things more consistent.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
|
|
|
|
| |
Using pad-to instead of passing the optional padding to append-kernel
or append-rootfs. It could be that the value of a variable is passed.
In case the variable is empty no error is thrown.
Furthermore the purpose of the extra parameter is hard to get without
reading the code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
| |
This reverts commit ec37a565878fd79d4127cbb843c17ce3b8dc97c0 and fixes
the underlying issue.
|
|
|
|
|
|
|
|
|
| |
The kernel size isn't passed to the append-kernel build step and the
resulting image bricks the device.
Fixes FS#168.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
|
|
| |
TP-Link has started providing US- and EU-specific stock firmwares that only
allow upgrading to firmwares with the same region code. Provide factory
images for both these regions.
To avoid confusing users outside these regions, we still provide a
"universal" factory.bin without a region code, although flashing either of
the US and EU images would work as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)
Flash instruction:
Use sysupgrade in vendor firmare which is based on OpenWrt.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
| |
The mw4530r-v1 profile in tp-link.mk is for Mercury MW4530R.
There is no such a device called TL-WDR4530.
Also change MERCURY to Mercury in /lib/ar71xx.sh
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
| |
Build/* templates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
| |
This add initial support for gl-mifi.
Product page: http://www.gl-inet.com/mifi/
Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
|
|
|
|
|
|
|
|
|
| |
Several legacy images were not buildable because of missing profile
definitions in legacy-devices.mk since MultiProfile was removed. Update
legacy-devices.mk to provide all necessary profiles, and change ordering
to match legacy.mk.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
This add initial support for gl-ar300m router.
Product page: http://www.gl-inet.com/ar300m/
Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers
Default configuration:
- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space
Flash instruction (do it under U-Boot, using RS232):
1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers
Default configuration:
- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
Get rid of remaining IMAGE_PROFILE references and move template calls
the right place
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
CAP324 nocloud was missing (No-Cloud) in description
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
|
|
|
|
|
| |
Reported-by: Syrone Wong <wong.syrone@gmail.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
| |
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
| |
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
rootfs part needs to be aligned to erase block size which is passed as
the 6th argument to Image/Build/Seama and is now 65536 since commit
commit 5119ee9 "ar71xx: fix bogus hardcoded kernel image size for Seama
images (fixes #20585)", but $(($(6) - 64)) still assumes that the
argument is a limit on kernel partition size, i.e. 1310720, so the
generated factory image is wrong in that the kernel will fail to find
the rootfs (FlySpray link at [1])
This patch will workaround it with the following steps
1. Calculate the required space for seama header and META data in step 5
2. Pre-padding 64 bytes to lzma-compressed loader
3. Generate correctly padded image-$(2).tmp
4. Strip out the padding
5. Seal it with seama utility
While at it convert seama to new build method
[1] FS#35 - mynet-n750 factory images don't find root partition,
https://bugs.lede-project.org/index.php?do=details&task_id=35
Reported-by: Steven Haigh <netwiz@crc.id.au>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
| |
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
| |
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
|
|
|
| |
Remove kmod-crypto-deflate and kmod-ledtrig-gpio as the device works the
same by default without them
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
|
|
|
| |
- Add missing macro to trigger the generation of 64k padded squashfs images
- Revert Zcomax image generation to use the prepared 64k squashfs image
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
| |
- Remove old style device profiles and convert them to device definitions
within the image building code
- Fix the legacy build macros for the changed eval depth in the legacy
image build wrapper
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit 59e98b27c93d282edb62fad756fd1c1e587c067f.
and
Revert "ar71xx: merge profiles into image building code"
This reverts commit 636089ead6864364798ac988299429d171051c0e.
these are still causing issues
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
After the conversion from legacy device profiles to the newer profile
information embedded in the image building code, the legacy recipes got
triggered twice with different eval depths, leading to shell syntax errors
when processing certain images.
The double processing was caused by the remaining Image/Build macro in
legacy.mk which serves as main entry point for the new style image build code
in conjunction with the newly introduced LegacyDevice/* macros which caused
the legacy image build fallback code to kick in.
In order to fix the issue, rework all legacy macros to work under the legacy
image build wrapper and remove the Image/Build macro of legacy.mk to prevent
legacy profiles getting executed in the context of the new build code.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
| |
Signed-off-by: John Crispin <john@phrozen.org>
|