aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/image
Commit message (Collapse)AuthorAgeFilesLines
...
* ar71xx: ew-dorin target moved from legacy to genericCatrinel Catrinescu2017-10-073-23/+20
| | | | | | Embedded Wireless Dorin platform moved from legacy to generic Signed-off-by: Catrinel Catrinescu <cc@80211.de>
* ar71xx: add metadata to wpj344 and wpj558 imagesEnrique Giraldo2017-09-101-0/+6
| | | | | | | | This adds metadata to wpj344 and wpj558 images to prevent loading firmware of wpj344 into wpj558 and vice versa. This until now was possible and break the units and had to be recovered from the uboot. Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
* ar71xx: add support for COMFAST CF-E355ACEnrique Giraldo2017-09-101-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9531 + QCA9882. Short specification: - 2x 10/100 Mbps Ethernet, with PoE support - 64MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, 802.11b/g/n - 2T2R 5 GHz, 802.11ac/n/a - built-in 4x 3 dBi antennas - output power (max): 500 mW (27 dBm) - 1x RGB LED, 1x button - built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net> [whitespace fixes, ac radio caldata offset fix] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for GL.iNet GL-USB150Piotr Dymacz2017-09-101-0/+13
| | | | | | | | | | | | | | | | | | | | | GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4) - 1T1R 2.4 GHz - 2x LED, 1x button - UART header on PCB Flash instruction: Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used to flash LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: use tplink-v1-header in place of mktplinkfw-kernelPiotr Dymacz2017-07-221-13/+8
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* build: move mktplinkfw-combined command to image-commands.mkPiotr Dymacz2017-07-221-18/+4
| | | | | | | | | | We will need "mktplinkfw-combined" command also in the "ramips" target for new MediaTek based TP-Link devices, with "safeloader" image type. Also, rename the command to "tplink-v1-header", use "VERSION_DIST" variable instead of "OpenWrt" and allow passing additional parameters. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-utils: mktplinkfw: rework combined image optionPiotr Dymacz2017-07-221-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | We use combined option in "mktplinkfw" tool for generating initramfs kernel images and header for kernel inside "safeloader" image type (in fact, only for TL-WR1043ND v4 at this moment). There is also "mktplinkfw-kernel" tool, a stripped-down version, used only for generating "simple" header, for safeloader image types. This changes how "mktplinkfw" handles combined images (which then will allow us to drop the stripped-down version of the tool): - drop "ignore size" command line option (it was used only for combined images anyway) - don't require "flash layout id" for combined images (we don't need and shouldn't limit size of the initramfs kernel and for kernels inside safeloader images, the "tplink-safeloader" tool does the size check) - require kernel address and entry point in command line parameters for combined images (consequence of previous point) - don't include md5 sum and firmware length values in header (they are needed only for update from vendor GUI and are ingored in case of initramfs and "tplink-safeloader" images) - drop "fake" flash layout for TL-WR1043ND v4 as it's no longer needed Also, adjust "mktplinkfw-combined" command in ar71xx/image/tp-link.mk to match introduced changes in "mktplinkfw" tool. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network AP121FPiotr Dymacz2017-07-221-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users. Device is based on Atheros AR9331 WiSoC and is running a custom version (updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR1) - 16 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet - 1T1R 2.4 GHz - 1x microSD (optional, on separate PCB) - 3x LED, 1x button, 1x switch - UART header on PCB Flash instruction (under U-Boot web recovery mode): 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with RJ45 port, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx/image: change unifi UBNT_CHIP to ar7240Alexander Couzens2017-07-131-1/+1
| | | | | | | | Verified by OEM firmware images which contains the same chip. Tested-by: Andreas Bräu <ab@andi95.de> Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: set US region code for TP-Link TL-WR710N v1 imageMatthias Schiffer2017-07-121-0/+1
| | | | | | | Non-US versions of the TP-Link TL-WR710N v1 don't have a region code so far, so we can just set US unconditionally. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: image: simplify Meraki MR16 device definitionPiotr Dymacz2017-07-091-10/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add metadata to some TP-Link imagesHenryk Heisig2017-07-091-2/+9
| | | | | | | This commit adds metadata to TP-Link sysupgrade images created by tplink-safeloader with uImage kernel header. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: fix TPLINK_BOARD_ID for Archer C58 and TL-WA855REPiotr Dymacz2017-07-041-2/+2
| | | | | | | Rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID for two ommited devices. Fixes: 7d6c63d ("build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID") Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link TL-WR902AC v1Piotr Dymacz2017-07-041-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of TL-MR3020 (both devices use very similar enclosure, in same size). New device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (GPIO-controlled power) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch - UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper resitors are missing on TX/RX lines) - 1x micro USB (for power only) Flash instructions: Use "factory" image under vendor GUI. Recovery instructions: This device contains tftp recovery mode inside U-Boot. You can use it to flash LEDE (use "factory" image) or vendor firmware. 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin" to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir. 3. Connect PC with LAN port, press the reset button, power up the router and keep button pressed until WPS LED lights up. 4. Router will download file from server, write it to flash and reboot. Root access over serial line in vendor firmware: root/sohoadmin. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: specify TPLINK_HWID for TP-Link RE450Piotr Dymacz2017-06-291-0/+1
| | | | | | | | | | TPLINK_HWID hasn't been specified for TP-Link RE450 since the begin. As we don't want to break sysupgrade (all existing LEDE release images for this board have TPLINK_HWID set to 0x0), set it explicitly to 0x0. Fixes FS#852 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_IDPiotr Dymacz2017-06-291-13/+13
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link Archer C58 v1Henryk Heisig2017-06-291-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 6x LED, 3x button - UART header on PCB, RX, TX at TP4+5 (backside) QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to patch macaddress. Flash instruction: Use "factory" image directly in vendor GUI. Recovery method: 1. Set PC to fixed ip address 192.168.0.66/24. 2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and rename it to "tp_recovery.bin". 3. Start a tftp server with the file "tp_recovery.bin" in its root directory. 4. Turn off the router. 5. Press and hold Reset button. 6. Turn on router with the reset button pressed and wait ~15 seconds. 7. Release the reset button and after a short time the firmware should be transferred from the tftp server. 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin erase 0x9f020000 +$filesize cp.b $fileaddr 0x9f020000 $filesize reset This commit is based on GitHub PR#1112 Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for TP-Link TL-WA855RE v1Federico Cappon2017-06-291-6/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/397/198 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x external antennas - 2x LED (green and orange in the same package), 2x button - UART: TP5(TX) and TP4(RX) test points on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in EU version of the device, but should work also with the same device version sold in other countries. Signed-off-by: Federico Cappon <dududede371@gmail.com>
* ar71xx: fix EnGenius ENS202EXT mtd definitionPiotr Dymacz2017-06-291-4/+4
| | | | | | | | | | | | | | Use statically defined sizes for kernel and rootfs mtd partitions. Vendor upgrade script writes both firmware parts independently which ends up in a gap between kernel and rootfs images. This results in incorrectly calculated rootfs_data start offset. Also, fix IMAGE_SIZE, DEVICE_PACKAGES and drop redundant KERNEL definition. Fixes FS#835 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: move Arduino Yun to generic building codeCamille Bilodeau2017-06-293-8/+10
| | | | | | | | | | | | | | | | | | Migrate Arduino Yun from legacy to generic building code. Note: the mtd partitioning is changed to adopt the LEDE default partitioning. It allows to have a kernel bigger than 1280k. It is necessary as kernel > 4.4 with default LEDE configuration grows bigger. To use the new partitioning, you need to update your U-Boot env in advance: setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro" setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000" saveenv Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
* ar71xx: remove Arduino Yun 8 MiB prototypeCamille Bilodeau2017-06-292-8/+0
| | | | | | | | | The Arduino Yun has 16 MiB flash. Early prototype boards with 8 MiB were not available for sell: https://blog.arduino.cc/2013/08/21/updating-about-arduino-yun-and-arduino-robot/ Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
* ar71xx/images/senao: fix reproducible issue using tarAlexander Couzens2017-06-251-0/+1
| | | | | | | | Use deterministic sorting Use numeric owner/group Set uid/gid to 0 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx/image: make tar calls reproducibleAlexander Couzens2017-06-252-3/+11
| | | | | | | | Use --mtime when SOURCE_DATE_EPOCH is set. Use gzip -n9z instead of tar z to remove timestamp in gzip header. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: add AVM FRITZ!WLAN Repeater 300E supportMathias Kresin2017-06-241-0/+13
| | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: AR7242 (Virian 400MHz) * RAM: 64 MB DDR (W9751G6JB-25) * Flash: 16MB SPI flash (S25FL129PIF) * WiFi: AR9382 (2.4/5GHz) + 2x SE2595L * LAN: 1x1000M (PEF7071V) To install LEDE via EVA bootloader, a FTP connection need to be established to 192.168.178.1 within the first seconds after power on: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: image: simplify TP-Link devices definitionsPiotr Dymacz2017-06-111-86/+28
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: fix TP-Link TL-WR710N v2/v2.1 BOARDNAMEPiotr Dymacz2017-06-111-2/+2
| | | | | | | | | | All TP-Link TL-WR710N versions share the same machine code. This has been working since the beginning as we don't use double-quotes to protect spaces inside command line values. Thus, kernel interprets 'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: tp-link.mk: keep devices in alphabetical orderPiotr Dymacz2017-06-111-406/+399
| | | | | | | | Keep TP-Link devices definitions in alphabetical order whenever it's possible. Also group together similar devices or devices from the same series. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link Archer C25 v1Ludwig Thomeczek2017-06-111-0/+16
| | | | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net> [minor code style fixes, boards alphabetical order fixes, reworked commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link TL-WR942N v1Serg Studzinskii2017-06-111-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on Qualcomm/Atheros QCA9561. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x USB 2.0 - 11x LED (most are controlled by 74HC595) - 2x button - UART header on PCB* * Serial console is disabled in OEM non-beta firmwares and corresponding GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by production (non-beta) U-Boot and firmware. Currently not working: 1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs by some U-Boot versions. Flash instruction under vendor GUI: 1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin". 2. Go to WEB interface and perform usual firmware upgrade. FLash instruction under U-Boot recovery mode (doesn't work in beta firmware): 1. Setup PC with static IP "192.168.0.66/24" and tftp server. 2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make it available to download from your tftp server. 3. Press "reset" button and power up the router, wait till "WPS" LED turns on. Flash instruction under U-Boot, using UART (can be done only with preinstalled UART-enabled U-Boot version!): 1. Use "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Serg Studzinskii <serguzhg@gmail.com> [minor code style fixes, extended commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: move WRTnode2Q to generic build targetPiotr Dymacz2017-06-113-8/+9
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: simplify Ubiquiti devices definitionsPiotr Dymacz2017-06-111-45/+29
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: mikrotik: shorten DEVICE_TITLEPiotr Dymacz2017-06-111-4/+4
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: use simply expanded variablesPiotr Dymacz2017-06-116-202/+202
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: update GL.iNet boards DEVICE_TITLEPiotr Dymacz2017-06-111-5/+5
| | | | | | | | Use "GL.iNet" as vendor name (based on information from the vendor, this is registered name of the company) and align model names with official website. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: fix 8devices boards DEVICE_TITLEPiotr Dymacz2017-06-111-2/+2
| | | | | | Be consistent with DEVICE_TITLE syntax and use vendor + board names. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: drop unused mtdlayouts from legacy.mkPiotr Dymacz2017-06-111-3/+0
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: cosmetic: drop redundant empty linesPiotr Dymacz2017-06-115-23/+0
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: add ROOTFS_SIZE to DEVICE_VARSPiotr Dymacz2017-06-111-4/+7
| | | | | | Also use ROOTFS_SIZE variable in place of static values. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: keep custom Build/* functions in separate filesPiotr Dymacz2017-06-113-53/+53
| | | | | | | | Most of the custom Build/* functions in ar71xx target are rarely used by image building code for devices from more than one subtarget. As they don't need to be always included, move them to corresponding *.mk files. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: keep DEVICE_VARS and Build/* at the beginningPiotr Dymacz2017-06-114-60/+60
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: simplify Compex devices definitionsPiotr Dymacz2017-06-111-20/+12
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: drop redundant kmod-usb-ohci from DEVICE_PACKAGESPiotr Dymacz2017-06-114-22/+22
| | | | | | kmod-usb-ohci is needed only on devices with AR71xx and AR7240 SoCs. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: drop redundant uboot-envtools from DEVICE_PACKAGESPiotr Dymacz2017-06-111-8/+4
| | | | | | uboot-envtools is already included in DEFAULT_PACKAGES for ar71xx. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: move Wallys DR344 to generic build targetPiotr Dymacz2017-05-303-7/+10
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for EnGenius ENS202EXTMarty Plummer2017-05-302-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius ENS202EXT is an outdoor wireless access point with 2-port 10/100 switch, detachable antennas and proprietery PoE. The device is based on Qualcomm/Atheros AR9341 v1. Specifications: - 535/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM - 16 MB of FLASH - UART (J1) header on PCB (unpopulated) - 2x 10/100 Mbps Ethernet - 2.4 GHz, up to 26dBm - 2x external, detachable antennas - 7x LED, 1x button Flash instructions: You have three options: - Use the vendor firmware upgrade page on the web interface and give it the factory.img. This is the easiest way to go about it. - If you have serial access during u-boot, interrupt the normal boot (any key before timeout) and run 'run failsafe_boot'; this will bring you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've bricked the normal firmware. - Use the vendor's management cli, which can be accessed via telnet with the same credentials as the web login (default admin:admin), then issue the following commands: *** Hi admin, welcome to use cli(V-1.6.7) *** ---========= Commands Help =========--- stat -- Status sys -- System wless2 -- 2.4G-Wireless mgmt -- Management tree -- Tree help -- Help reboot -- Reboot ens202ext>mgmt Management ---========= Commands Help =========--- admin -- Administration mvlan -- Management VLAN settings snmp -- SNMP settings backup -- Backup/Restore settings autorb -- Auto reboot settings fwgrade -- Firmware upgrade time -- Time settings wifisch -- Wifi schedule log -- Log diag -- Diagnostics disc -- Device Discovery logout -- Logout help -- Help exit -- Exit ens202ext/mgmt>fwgrade Management --> Firmware upgrade ---========= Commands Help =========--- fwup -- Firmware upgrade help -- Help exit -- Exit ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
* ar71xx: fix LED defines for TP-Link TL-WR740N v6Andrey Polischuk2017-05-301-1/+1
| | | | | | Signed-off-by: Andrey Polischuk <androld.b@gmail.com> [changed commit subject, dropped redundant kernel config symbol] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* Move enablemodem from ramips to new package adb-enablemodem and make it used ↵Filip Moc2017-05-271-1/+1
| | | | | | also by TL-MR6400 Signed-off-by: Filip Moc <lede@moc6.cz>
* ar71xx: Add support for TP-Link MR6400Filip Moc2017-05-271-0/+10
| | | | | | | | | | | | | | | | | You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin on 192.168.0.66/24, connect to any ethernet port and power on device while holding the reset button). Flashing via OEM web interface does not work. Hardware Specification (v1.0 EU): - SoC: QCA9531 - Flash: Winbond W25Q64FV (8MiB) - RAM: EtronTech EM6AB160TSE-5G (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 2NIC (3x100M + 1x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 12V 1A Signed-off-by: Filip Moc <lede@moc6.cz>
* ar71xx: change image version for ubiquiti devicesMatthias Fritzsche2017-05-251-3/+3
| | | | | | | | | | changes the image version from hardcoded OpenWrt to $VERSION_DIST. AirOS shows a notification with the image version during a firmware upgrade. fixes #582 Signed-off-by: Matthias Fritzsche <txt.file@txtfile.eu>
* Revert "ar71xx: Add support for Teltonika RUT900"John Crispin2017-05-181-11/+0
| | | | | | | | This reverts commit 224e5f5efa22b8a0132522367afd3b22f05d53e1. pepe2k pointed out that this was not ready to merge Signed-off-by: John Crispin <john@phrozen.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-14 22:34:37 +0000