aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/image/tp-link.mk
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: fix LED defines for TP-Link TL-WR740N v6Andrey Polischuk2017-05-301-1/+1
| | | | | | Signed-off-by: Andrey Polischuk <androld.b@gmail.com> [changed commit subject, dropped redundant kernel config symbol] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* Move enablemodem from ramips to new package adb-enablemodem and make it used ↵Filip Moc2017-05-271-1/+1
| | | | | | also by TL-MR6400 Signed-off-by: Filip Moc <lede@moc6.cz>
* ar71xx: Add support for TP-Link MR6400Filip Moc2017-05-271-0/+10
| | | | | | | | | | | | | | | | | You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin on 192.168.0.66/24, connect to any ethernet port and power on device while holding the reset button). Flashing via OEM web interface does not work. Hardware Specification (v1.0 EU): - SoC: QCA9531 - Flash: Winbond W25Q64FV (8MiB) - RAM: EtronTech EM6AB160TSE-5G (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 2NIC (3x100M + 1x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 12V 1A Signed-off-by: Filip Moc <lede@moc6.cz>
* Revert "ar71xx: Add support for Teltonika RUT900"John Crispin2017-05-181-11/+0
| | | | | | | | This reverts commit 224e5f5efa22b8a0132522367afd3b22f05d53e1. pepe2k pointed out that this was not ready to merge Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: Add support for Teltonika RUT900Steffen Weinreich2017-05-181-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet ports, I/O, RS232, RS485, GPS. The device ist based on a Atheros AR9344 rev 3, Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM - 16 MB of FLASH - Serial Console header on a Card Board edge connector - 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN) - 2.4 GHz Wifi - 2x external, detachable Wifi antennas - LTE Modem Huawei ME909u-521 (Also other Modem seen) - 2x LTE antennas - 1x GPS antenna - 7x LED, 1x button - 1x USB Connector - 1x Serial RS232 - 1x Serial RS485 - 1x MicroSD Card The GPL sources of the device are available at www.teltonika.lt/gpl/ and are based on OpenWRT Barrier Breaker (14.07) Running from tftp: The Router starts into the uboot Webupdater if the Button ist pressed more than 3 seconds, if no Network cable is attached it starts the uboot serial console, from there the router loads the firmware image via tftpboot from 192.168.1.2:firmware.bin (the router has the 192.168.1.1). With bootm the loaded image will be booted. Signed-off-by: Steffen Weinreich <steve@weinreich.org>
* ar71xx: tp-link.mk: always include device version in image and DEVICE_TITLEPiotr Dymacz2017-04-031-54/+54
| | | | | | | | | | | | | | | | | | | | There are currently several supported TP-Link devices without specified version number in image name and/or DEVICE_TITLE (e.g. WBS210, WBS510, TL-WR810N, TL-WA7510N, TL-WPA8630), but vendor website shows that there are already more than one version of them on the market. For devices like Archer C5, which second version is based on a total different platform, missing version number in DEVICE_TITLE (used in menuconfig) might be misleading for users. To make it less confusing for users and easier to maintain in future, include version number in image name and DEVICE_TITLE for all TP-Link devices, even if there is only one version of device at the moment. Also, keep DEVICE_TITLE in same format for all TP-Link devices. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Acked-by: John Crispin <john@phrozen.org>
* ar71xx: add TP-LINK TL-WR841N/ND v12 imageVittorio Gambaletta2017-04-031-1/+7
| | | | | | | | | | | | | This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC ID, same TFTP image name...). If the stock firmware web interface doesn't accept LEDE factory image, it can be flashed via the U-Boot TFTP recovery mode, by long-pressing the reset button after power on. The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12). Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
* treewide: select ath10k firmware explicitMathias Kresin2017-03-241-2/+2
| | | | | | Do not rely on the default firmware selected by ath10k. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: image: fix indentationPiotr Dymacz2017-03-231-538/+538
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-LINK TL-WR840N v2 and v3Vaclav Svoboda2017-03-231-1/+18
| | | | | | | | | | | | | | This patch adds support for the TP-LINK TL-WR840N v2 and v3. - SoC: Qualcomm QCA9533-BL3A (650 MHz) - RAM: 32 MiB (Zentel A3S56D40GTP) - Flash: 4 MiB (v2: Macronix MX 25L323F) (v3: Winbond 25Q32FVSIG) - LAN: 4x 100M - WAN: 1x 100M Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
* ar71xx: add support for TL-WR802N Version 2Thomas Roberts2017-02-201-2/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR802N Version 2. Specification: - SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc) - RAM: 32 MiB - Storage: 4 MiB of FLash on board - Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) Installation through OEM Web Interface: - Connect to TL-WR802N by Ethernet or Wi-Fi - Go to http://192.168.0.1 (default user is "admin" & password is "admin) - Go to "System Tools -> Firmware Upgrade" - Browse for firmware "*.factory-us.bin" or "*.factory-eu.bin" for eu model - Click upgrade Installation through tftp: Note: T_OUT, T_IN and GND on the board must be connected to USB TTL Serial Configuration 115200 8n1 - Boot the TL-WR802N - When "Autobooting in 1 seconds" appears type "tpl" followed by enter - Connect to the board Ethernet port (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10) - tftpboot 0x80000000 <Firmware Image Name> - Record the result of "printenv bootcmd" - Enter "erase <Result of 'printenv bootcmd'> +0x3c0000" (e.g erase 0x9f020000 +0x3c0000) - Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000" (e.g cp.b 0x80000000 0x9f020000 0x3c0000) - Enter "bootm <Result of 'printenv bootcmd'>" (e.g bootm 0x9f020000) Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
* ar71xx: add support for TP-Link TL-WA850RE v2Piotr Dymacz2017-02-141-1/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/391/195 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x internal antennas (embedded on PCB) - 9x LED (all can be turned off with GPIO15), 2x button - UART (J3) header on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in US version of the device, but should work also with the same device version sold in other countries. Available FLASH space, with LEDE trunk, is only 240 KB. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: fix DEVICE_TITLE for several devicesPiotr Dymacz2017-02-031-1/+1
| | | | | | Be consistent with form and format of the vendor names. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support to TP-Link Archer C59v1 and C60v1Henryk Heisig2017-01-261-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: add support for TP-Link WBS210/510Matthias Schiffer2017-01-051-1/+17
| | | | | | | The devices are mostly identical to the CPE210/510, but use external antennas. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: RE450: enable building of TP-Link RE450Radek Dostál2016-12-221-0/+16
| | | | Signed-off-by: Radek Dostál <rd@radekdostal.com>
* firmware-utils: kernel image generator for TP-Link RE450Tal Keren2016-12-221-0/+10
| | | | | | | | | | | | | | | | | The firmware image that is used in TP-Link RE450 (and some more devices from the RE series) is tplink-safeloader. In the kernel partition, the kernel is compressed in a regular tp-link firmware that is just used for booting. Since it is only used for compressing and booting, only four fields are filled in the header: Vendor, version, kernel load address and kernel entry point. mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such images. It also specifies the hardware id (as it is in the product info section), so when doing a sysupgrade - the existing code will check for hardware compatibility. Signed-off-by: Tal Keren <kooolk@gmail.com> [rd@radekdostal.com: add build target to .../image/tp-link.mk] Signed-off-by: Radek Dostál <rd@radekdostal.com>
* ar71xx: remove redundant -j from TL-WR1043ND v4 kernel build commandMatthias Schiffer2016-12-211-1/+1
| | | | | | | mktplinkfw ignores -j in combined mode, the EOF marker is added by tplink-safeloader. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add support for TP-LINK WR1043ND v4Ludwig Thomeczek2016-12-201-1/+18
| | | | Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* ar71xx: rename mktplinkfw-initramfs to more generic mktplinkfw-combinedMatthias Schiffer2016-12-201-5/+5
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add support for TP-LINK TL-WR940N v4David Lutz2016-12-161-1/+12
| | | | Signed-off-by: David Lutz <kpanic@hirnduenger.de>
* ar71xx: tl-wpa8630: Use dynamic parsing of the firmware partitionHenryk Heisig2016-11-161-2/+0
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: generate region-coded factory images for TP-Link TL-WR841ND v11Matthias Schiffer2016-11-111-0/+3
| | | | | | | | The latest stock firmwares for US and EU regions have started checking the region code. Tested-by: Andreas Ziegler <ml@andreas-ziegler.de> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: tl-wpa8630: Fix kernel lenghtHenryk Heisig2016-11-081-1/+1
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: wpa8630: change board name to tl-wpa8630Henryk Heisig2016-11-081-12/+12
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: Add support to Powerline ac TP-Link WPA8630Henryk Heisig2016-10-311-0/+12
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for TP-Link WR802N v1Julius Schulz-Zander2016-10-261-0/+10
| | | | | | | This patch adds support solely for version 1 of the TP-Link WR802N. It is based on Rick Pannen's patch posted on the OpenWrt devel list. Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
* switch to the new usbport LED triggerRafał Miłecki2016-10-191-31/+31
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: Add support to TP-Link EAP120Henryk Heisig2016-10-181-0/+15
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: set EU region code for TP-Link TL-WA901ND v4Matthias Schiffer2016-10-151-0/+1
| | | | | | | | | | | | | There is no US firmware for the TL-WA901ND v4 yet, so we'll just unconditionally set the EU region for now. This makes LEDE flashable on these devices again. The format of the region string is slightly different from the one used on the Archer C7 that is generated by mktplinkfw (the second half of the region string is missing), but it's similar enough to make it work. Tested-by: Jannis Pinter <jannis@pinterjann.is> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: build image for Archer C7 v2 ILAmir Rachum2016-10-091-1/+11
| | | | | | | TP-Link uses a different region coding mechanism for IL firmware for the Archer C7 v2. Instead of of setting the region, they set a different TPLINK_HWREV. Signed-off-by: Amir Rachum <amir@rachum.com>
* ar71xx: set region code of TP-Link TL-WDR3600/4300 to USMatthias Schiffer2016-09-151-0/+2
| | | | | | | | There are currently two stock firmwares for the TL-WDR3600/4300, a US and a universal version. Both allow installing images with US region code, so we don't need to provide multiple images. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: separate TP-Link TL-WDR3600/4300/4310 profilesMatthias Schiffer2016-09-151-9/+19
| | | | | | | | | Simplify modifying some of the images without affecting the others. While we're at it, also unify the profiles to use := syntax and add "v1" to the TL-WDR4300 name to make things more consistent. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: generate US- and EU-specific images for the Archer C7 v2Matthias Schiffer2016-08-281-1/+3
| | | | | | | | | | | | TP-Link has started providing US- and EU-specific stock firmwares that only allow upgrading to firmwares with the same region code. Provide factory images for both these regions. To avoid confusing users outside these regions, we still provide a "universal" factory.bin without a region code, although flashing either of the US and EU images would work as well. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: fix profile name of Mercury MW4530RChuanhong Guo2016-08-151-1/+1
| | | | | | | | The mw4530r-v1 profile in tp-link.mk is for Mercury MW4530R. There is no such a device called TL-WDR4530. Also change MERCURY to Mercury in /lib/ar71xx.sh Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* image: add a helper variable for getting kernel/rootfs from within image ↵Felix Fietkau2016-07-311-1/+1
| | | | | | Build/* templates Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add ath10k firmware to profile defaults where ath10k is usedFelix Fietkau2016-07-221-5/+5
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: merge profiles into image building codeJo-Philipp Wich2016-06-271-2/+126
| | | | | | | | | | | - Remove old style device profiles and convert them to device definitions within the image building code - Fix the legacy build macros for the changed eval depth in the legacy image build wrapper Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* Revert "ar71xx: fix legacy image building"John Crispin2016-06-231-126/+2
| | | | | | | | | | | | | | This reverts commit 59e98b27c93d282edb62fad756fd1c1e587c067f. and Revert "ar71xx: merge profiles into image building code" This reverts commit 636089ead6864364798ac988299429d171051c0e. these are still causing issues Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: merge profiles into image building codeJohn Crispin2016-06-221-2/+126
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: Fix TL-WR841N v11 LEDs, use separate machineStijn Segers2016-05-311-1/+1
| | | | Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* tools/tplink-safeloader: split CPE210 from CPE510 profileAlexander Couzens2016-05-271-0/+1
| | | | | | | | | The CPE210 was still described for the OEM upgrade as compatible, even the wireless configuration isn't compatible anymore between both series (2ghz and 5ghz). Update the CPE210 image profile to use the new profile. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: switch ordering and template to improve readabilityAlexander Couzens2016-05-271-5/+5
| | | | | | | The CPE210's ancestor is the CPE510 not the other way around. The device profile is also named after the CPE510. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* include/image.mk: move build step tplink-safeloader to image.mkAsh Benz2016-05-271-12/+0
| | | | | | Move tplink-safeloader from target/linux/ar71xx/image/tp-link.mk to include/image.mk Signed-off-by: Ash Benz <ash.benz@bk.ru>
* ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510Alexander Couzens2016-05-231-3/+9
| | | | | | | Split profile into 2GHz and 5GHz. The 5GHz devices are quite "special". The 2 GHz works perfect. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: split tp-link image building code into a separate fileFelix Fietkau2016-05-231-0/+746
Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-16 17:49:54 +0000