aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/image/tiny.mk
Commit message (Collapse)AuthorAgeFilesLines
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-061-1/+1
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: modify mtd partitions for Buffalo BHR-4GRV2INAGAKI Hiroshi2018-11-261-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and move it to generic subtarget. In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs" partition in the stock firmware. This causes the size of the kernel to be limited by the fixed value. 0x50000 0xe80000 0xff0000 +-------------------------------+--------------+ | rootfs | kernel | | (14528k) | (1472k) | +-------------------------------+--------------+ After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2 exceeded the limit, and it breaks builds on official buildbot. Since this issue was also confirmed in ath79, I modified the mtd partitions to get rid of that limitation. 0x50000 0xff0000 +----------------------------------------------+ | firmware | | (16000k) | +----------------------------------------------+ However, this commit breaks compatibility with ar71xx firmware, so I dropped "SUPPORTED_DEVICES += bhr-4grv2". This commit requires new flash instruction instead of the old one. Flash instruction using initramfs image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Set the IP address of the computer to 192.168.12.10 3. Rename the OpenWrt initramfs image to "bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP directory 4. Start the tftp server on the computer 5. While holding down the "ECO" button, connect power cable to BHR-4GRV2 and turn on it 6. Flashing (orange) diag LED and release the finger from the button, BHR-4GRV2 downloads the intiramfs image from TFTP server and boot with it 7. On the initramfs image, create "/etc/fw_env.config" file with following contents /dev/mtd1 0x0 0x10000 0x10000 8. Execute following commands to add environment variables for u-boot fw_setenv ipaddr 192.168.12.1 fw_setenv serverip 192.168.12.10 fw_setenv ethaddr 00:aa:bb:cc:dd:ee fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" 9. Perform sysupgrade with squashfs-sysupgrade image 10. Wait ~150 seconds to complete flashing And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC, not QCA9558. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ar71xx: disable some tiny targets with kernel 4.14Koen Vandeputte2018-11-051-2/+0
| | | | | | | | | | | | | | | | | | | | | The bump to kernel 4.14 caused a massive increase in kernel size. For most targets, switching them to dynamic partitioning allowed to cope with this. On some targets, the kernel partition is located behind the rootfs, which disallows switching to dynamic partitioning as the boot location would be altered, requiring a u-boot change. Also within the tiny section, which disables kernel symbols etc to decrease the image size, the partition size is still too small. Disable these targets for now, fixing image generation: - Buffalo BHR-4GRV2 - Zbtlink ZBT-WE1526 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for Buffalo BHR-4GRV2INAGAKI Hiroshi2018-08-091-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros QCA9558. Ported from ar71xx target. Specification: - Qualcomm Atheros QCA9558 - 64 MB of RAM - 16 MB of Flash - 5x 10/100/1000 Ethernet - QCA8337N - 4x LEDs, 2x keys - UART header on PCB - Vcc, TX, RX, GND from LED side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Connect power cable to BHR-4GRV2 and turn on it 3. Access to "http://192.168.12.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新実行") button 5. Wait ~120 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ar71xx: move boards to tiny subtargetMathias Kresin2018-07-121-0/+33
Move boards to the tiny subtarget which break the build if the kernel is set to "Optimize for performance". Signed-off-by: Mathias Kresin <dev@kresin.me>