aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/image/generic.mk
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: add support for YunCore SR3200 and XD3200Piotr Dymacz2016-12-121-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: move DomyWifi DW33D to nand subtargetPiotr Dymacz2016-11-241-11/+0
| | | | | | | | | This device uses NAND FLASH, so it should be kept in nand subtarget. Also, inlcude in packages kmod-usb-ledtrig-usbport instead of obsolete kmod-ledtrig-usbdev. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore CPE830Piotr Dymacz2016-11-211-0/+8
| | | | | | | | | CPE830 is a clone of AP90Q, with different type of antenna (panel) and additional 4 LEDs for WiFi signal level indication. Use the same flash approach as for YunCore AP90Q. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore CPE870Piotr Dymacz2016-11-211-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341. Short specification: - 535/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm - internal 14 dBi panel antenna - 8x LED, 1x button - UART (JP1) header on PCB Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. setenv bootcmd "bootm 0x9f020000" 5. saveenv && reset Vendor firmware access (login/password): Admin/5up Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore AP90QPiotr Dymacz2016-11-211-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2. Short specification: - 650/600/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz with external PA, up to 29 dBm - 2x internal 5 dBi omni antennas - 4x LED, 1x button - UART (JP1) header on PCB Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Flash instruction under vendor fimrware, using telnet/SSH: 1. Connect PC with 192.168.1.x address to WAN port 2. Power up device, enter failsafe mode with button (no LED indicator!) 3. Change root password and reboot (mount_root, passwd ..., reboot -f) 4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP 5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 6. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9f050000" - mtd erase firmware - mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E380AC v1 and v2Piotr Dymacz2016-11-211-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035. There are two versions of this model, with different RAM and U-Boot mtd partition sizes: - v1: 128 MB of RAM, 128 KB U-Boot image size - v2: 256 MB of RAM, 256 KB U-Boot image size Version number is available only inside vendor GUI, hardware and markings are the same. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 1x 10/100/1000 Mbps Ethernet, with PoE support - 128 or 256 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm - 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm - 6x internal antennas - 1x RGB LED, 1x button - UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB - external watchdog (Pericon Technology PT7A7514) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530NPiotr Dymacz2016-11-211-1/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As we already have support for CF-E316N v2 and many devices from this vendor look similar, the support was included in existing mach-*.c file, with few cleanups and fixes. All 3 devices are based on Qualcomm/Atheros QCA9531 v2. COMFAST CF-E320N v2 is a ceiling mount AP with PoE support. Short specification: - 650/393/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - 2x internal antennas - 1x RGB LED, 1x button - UART (J1), GPIO (J9) and USB (J2) headers on PCB - external watchdog (Pericon Technology PT7A7514) COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support. They seem to have different only the front panel. Short specification: - 650/393/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, WAN with PoE support - 1x USB 2.0 (in CF-E520N covered by panel, available on PCB) - 32 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - 2x internal antennas - 1x LED, 1x button - UART (J1) headers on PCB Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Buffalo BHR-4GRV2FUKAUMI Naoki2016-11-161-0/+21
| | | | Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
* ar71xx: add support for D-Link DAP-2695 rev. A1Stijn Tintel2016-10-271-0/+29
| | | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: John Crispin <john@phrozen.org>
* ar71xx: add mac partition to the MR12/MR16Chris Blake2016-10-261-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space after u-boot-env is used to store the boards Mac address. Sadly as this was removed on any device already on OpenWRT/LEDE, moving forward a new, 64k partition named "mac" will be used to store the mac address for the device (which is the minimum size). This allows users to properly set the correct MAC, without editing the ART partition (which holds the same MAC for all devices). The reason the space is taken from kernel instead of rootfs is currently kernels are only 1.3MB, so that way we can leave the current rootfs space alone for users who fully utilize the available storage space. Once this partition is added to a device, you can set your MAC doing the following: mtd erase mac echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5 sync && reboot Where 00:18:0a:33:44:55 is your MAC address. This was tested, and confirmed working on both the MR12 and MR16. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ar71xx: Move MR12 & MR16 from legacy to genericChris Blake2016-10-261-0/+26
| | | | | | | | | | | This moves the Meraki MR12 and Meraki MR16 to the new generic target. Tested and verified working on both devices. Note that kernel/rootfs images are still generated. This is because they are used for the inital flashing process due to the fun pace at which UBoot erases/writes to SPI. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ar71xx: Add support to DomyWifi DW33DJing Lin2016-10-251-0/+11
| | | | Signed-off-by: Jing Lin <mumuqz@163.com>
* switch to the new usbport LED triggerRafał Miłecki2016-10-191-8/+8
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: move dragino2 from legacy to genericKarl Palsson2016-10-131-0/+10
| | | | | | Tested on real hardware with r1804. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ar71xx: add userspace support for D-Link DIR-869 A1, generate imagesFlorian Beier2016-10-111-1/+15
| | | | | | Signed-off-by: Florian Beier <beier.florian@gmail.com> [Matthias Schiffer: fix factory image, improve commit message] Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: avoid double lzma compression of kernel for SEAMA imagesMatthias Schiffer2016-10-111-1/+1
| | | | | | | | Use relocation loader instead of lzma loader. Tested on D-Link DIR-869 A1. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: clean up SEAMA image build codeMatthias Schiffer2016-10-111-34/+18
| | | | | | | | | | | Split seama-factory and seama-sysupgrade into smaller pieces (similar to the ramips code) to make the image generation more flexible. Also use standard pad-offset instead of adding a block of zeros at the beginning of the image that is later cut off again. Standard pad-rootfs can be used as the seal header doesn't contain an image size or checksum. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: mark U-Boot and radio calibration data partitions as read-onlyPiotr Dymacz2016-09-191-6/+6
| | | | | | | General convention is to keep U-Boot and radio calibration data (ART) mtd partitions marked as read-only. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* image: remove padding parameter from append-kernel/append-rootfsMathias Kresin2016-09-131-3/+3
| | | | | | | | | | | Using pad-to instead of passing the optional padding to append-kernel or append-rootfs. It could be that the value of a variable is passed. In case the variable is empty no error is thrown. Furthermore the purpose of the extra parameter is hard to get without reading the code. Signed-off-by: Mathias Kresin <dev@kresin.me>
* image: add KERNEL_SIZE to the default device varsMathias Kresin2016-09-131-2/+2
| | | | | This reverts commit ec37a565878fd79d4127cbb843c17ce3b8dc97c0 and fixes the underlying issue.
* ar71xx: fix typo in image build codeMathias Kresin2016-09-111-2/+2
| | | | | | | | | The kernel size isn't passed to the append-kernel build step and the resulting image bricks the device. Fixes FS#168. Signed-off-by: Mathias Kresin <dev@kresin.me>
* image: add a helper variable for getting kernel/rootfs from within image ↵Felix Fietkau2016-07-311-6/+6
| | | | | | Build/* templates Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for gl-mifiZhao Gang2016-07-241-0/+10
| | | | | | | This add initial support for gl-mifi. Product page: http://www.gl-inet.com/mifi/ Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
* ar71xx: add ath10k firmware to profile defaults where ath10k is usedFelix Fietkau2016-07-221-3/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for gl-ar300mZhao Gang2016-07-201-0/+10
| | | | | | | This add initial support for gl-ar300m router. Product page: http://www.gl-inet.com/ar300m/ Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
* ar71xx: add support for jjPlus JWAP230Piotr Dymacz2016-07-131-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 2x 10/100/1000 Mbps Ethernet - 128 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm - 3x MMCX connectors - power input: 802.3at PoE or wide range DC (36-57 V) - optional 802.3af PSE - 1x mini-PCIe connector with PCIe, USB buses and SIM slot - 1x mini-PCIe connector with PCIe bus - 1x USB type-A connector - 6x LED, 1x button (hardware reset) - RS232 (MAX3223) and (E)JTAG headers Default configuration: - WAN on eth1 (RJ45 near LEDs with PoE input) - LAN on eth0 (RJ45 near DC jack) - left top LED set to be status LED - all LEDs configurable form user space Flash instruction (do it under U-Boot, using RS232): 1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Wallys DR531Piotr Dymacz2016-07-131-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wallys DR531 is based on Qualcomm Atheros QCA9531 v2. Short specification: - 550/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm - 2x MMCX connectors - mini-PCIe connector with PCIe/USB buses and SIM slot - 7x LED, 1x button, 1x optional buzzer - UART, (E)JTAG and LED headers Default configuration: - WAN on eth1 (RJ45 near DC jack) - LAN on eth0 (RJ45 near button) - S4 LED set to be status LED - all LEDs configurable form user space - button configured for reset Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: Fix PowerCloud CAP324 No Cloud titleDaniel Dickinson2016-07-111-1/+1
| | | | | | CAP324 nocloud was missing (No-Cloud) in description Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
* ar71xx: image: fix typo in MTDPARTS def for qihoo-c301Yousong Zhou2016-07-111-1/+1
| | | | | Reported-by: Syrone Wong <wong.syrone@gmail.com> Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ar71xx: image: seama: fix making factory and sysupgrade imageYousong Zhou2016-07-111-11/+12
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ar71xx: seama: fix making factory imagesYousong Zhou2016-06-301-0/+81
| | | | | | | | | | | | | | | | | | | | | | | | | | rootfs part needs to be aligned to erase block size which is passed as the 6th argument to Image/Build/Seama and is now 65536 since commit commit 5119ee9 "ar71xx: fix bogus hardcoded kernel image size for Seama images (fixes #20585)", but $(($(6) - 64)) still assumes that the argument is a limit on kernel partition size, i.e. 1310720, so the generated factory image is wrong in that the kernel will fail to find the rootfs (FlySpray link at [1]) This patch will workaround it with the following steps 1. Calculate the required space for seama header and META data in step 5 2. Pre-padding 64 bytes to lzma-compressed loader 3. Generate correctly padded image-$(2).tmp 4. Strip out the padding 5. Seal it with seama utility While at it convert seama to new build method [1] FS#35 - mynet-n750 factory images don't find root partition, https://bugs.lede-project.org/index.php?do=details&task_id=35 Reported-by: Steven Haigh <netwiz@crc.id.au> Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ar71xx: image: unify indentation with 2 whitespacesYousong Zhou2016-06-301-112/+112
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ar71xx: hiwifi-hc6361: move packages selection to generic.mkYousong Zhou2016-06-301-6/+9
| | | | | | | Remove kmod-crypto-deflate and kmod-ledtrig-gpio as the device works the same by default without them Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ar71xx: merge profiles into image building codeJo-Philipp Wich2016-06-271-34/+101
| | | | | | | | | | | - Remove old style device profiles and convert them to device definitions within the image building code - Fix the legacy build macros for the changed eval depth in the legacy image build wrapper Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* Revert "ar71xx: fix legacy image building"John Crispin2016-06-231-101/+34
| | | | | | | | | | | | | | This reverts commit 59e98b27c93d282edb62fad756fd1c1e587c067f. and Revert "ar71xx: merge profiles into image building code" This reverts commit 636089ead6864364798ac988299429d171051c0e. these are still causing issues Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: merge profiles into image building codeJohn Crispin2016-06-221-34/+101
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: hiwifi-hc6361: lift size limit on kernel and rootfs partsYousong Zhou2016-06-221-0/+20
| | | | | | | | | | | | | | | | | | | | | | The patch has been run-tested and the relevant dmsg logs are as the following [ 0.762447] Creating 5 MTD partitions on "spi0.0": [ 0.767217] 0x000000000000-0x000000010000 : "u-boot" [ 0.775139] 0x000000010000-0x000000020000 : "bdinfo" [ 0.781014] 0x000000020000-0x000000fe0000 : "firmware" [ 0.810558] 2 uimage-fw partitions found on MTD device firmware [ 0.815043] 0x000000020000-0x000000170000 : "kernel" [ 0.821925] 0x000000170000-0x000000fe0000 : "rootfs" [ 0.827587] mtd: device 4 (rootfs) set to be root filesystem [ 0.831937] 1 squashfs-split partitions found on MTD device rootfs [ 0.837983] 0x0000005c0000-0x000000fe0000 : "rootfs_data" [ 0.845621] 0x000000fe0000-0x000000ff0000 : "backup" [ 0.851445] 0x000000ff0000-0x000001000000 : "art" While at it, convert to new build method Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ar71xx: add support for OpenEmbed SOM9331Allan Nick Pedrana2016-06-071-0/+9
| | | | | | | | This patch adds the target profile SOM9331 and configures hardware functionality for the 3x Eth Ports & corresponding LED's, the USB Host, the USART to USB bridge and the System LED. Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
* ar71xx: move generic device image definitions to a separate fileFelix Fietkau2016-05-231-0/+335
Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-13 09:41:59 +0000