aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/files
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: Add support to TP-Link EAP120Henryk Heisig2016-10-184-0/+137
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for the Airtight C-60Christian Lamparter2016-10-154-0/+214
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Airtight C-60. SOC: Atheros AR9344 rev 2 (CPU:560.000MHz) RAM: 128 MiB NOR: MX25L3205D 4MiB NAND: ST Micro NAND 32MiB 3,3V 8-bit SW-NET: AR8327N (2 Ports) WLAN1: Dual-Band AR9340 Rev:2 (built-in SoC) WLAN2: Dual-Band AR9300 Rev:4 PCIe Chip The switch is setup for an accesspoint: LAN1: (gigabit) is the wan-port. LAN2: (fast ethernet) is bridged with the br-lan. Flashing Guide (via initramfs): 1. Connect a PC to the serial port of the C-60. power up the C-60. Enter u-boot command prompt: #> nand erase #> setenv bootcmd "bootm 0x9f060000" #> saveenv #> setenv ipaddr 192.168.1.1 #> setenv netmask 255.255.255.0 #> setenv serverip 192.168.1.100 #> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin #> tftpboot #> bootm 2. Wait for the C-60 to boot LEDE. On the root prompt. Enter: # ubiformat /dev/mtd4 # ubiattach -p /dev/mtd4 3. After that copy the sysupgrade.tar onto the router and run: # sysupgrade sysupgrade.tar to flash the image. Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided a C-60 unit and he helped with debugging the switch, LEDs and platfrom support. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ar71xx: add kernel support for D-Link DIR-869 A1Matthias Schiffer2016-10-114-0/+190
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: comsetic cleanups in files/arch/mips/ath79/{Makefile,machtypes.h}Piotr Dymacz2016-10-042-422/+422
| | | | | | Keep everything in alphabetical order and aligned in columns. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix LED names for GL Innovations boardsPiotr Dymacz2016-10-045-18/+18
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker GatewayChris Blake2016-09-274-0/+178
| | | | | | | | | This patch adds support for Cisco's Z1. Detailed instructions for the flashing the device can be found in the OpenWrt wiki: <https://wiki.openwrt.org/toh/meraki/z1> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ar71xx: fix ethernet driver fast reset issue causing tx timeoutsFelix Fietkau2016-09-031-1/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: disable flow control to the built-in switch on AR934xFelix Fietkau2016-08-251-1/+0
| | | | | | | It apparently causes a regression on some devices if the ethernet cable is plugged in while booting. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for Zbtlink ZBT-WE1526Piotr Dymacz2016-08-184-0/+165
| | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2. Short specification: - 650/400/200 MHz (CPU/DDR/AHB) - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - two external, non-detachable antennas - 8x LED, 1x button - UART header (pinout: VCC, RX, TX, GND) Flash instruction: Use sysupgrade in vendor firmare which is based on OpenWrt. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for gl-mifiZhao Gang2016-07-244-0/+126
| | | | | | | This add initial support for gl-mifi. Product page: http://www.gl-inet.com/mifi/ Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
* ar71xx: add support for gl-ar300mZhao Gang2016-07-204-0/+194
| | | | | | | This add initial support for gl-ar300m router. Product page: http://www.gl-inet.com/ar300m/ Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
* ar71xx: add software transmit timestamp supportStephen Walker2016-07-152-0/+3
| | | | | | Add software transmit timestamp and ethtool (-T) timestamp support Signed-off-by: Stephen Walker <stephendwalker+github@gmail.com>
* ar71xx: add support for jjPlus JWAP230Piotr Dymacz2016-07-134-0/+169
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 2x 10/100/1000 Mbps Ethernet - 128 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm - 3x MMCX connectors - power input: 802.3at PoE or wide range DC (36-57 V) - optional 802.3af PSE - 1x mini-PCIe connector with PCIe, USB buses and SIM slot - 1x mini-PCIe connector with PCIe bus - 1x USB type-A connector - 6x LED, 1x button (hardware reset) - RS232 (MAX3223) and (E)JTAG headers Default configuration: - WAN on eth1 (RJ45 near LEDs with PoE input) - LAN on eth0 (RJ45 near DC jack) - left top LED set to be status LED - all LEDs configurable form user space Flash instruction (do it under U-Boot, using RS232): 1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Wallys DR531Piotr Dymacz2016-07-134-0/+167
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wallys DR531 is based on Qualcomm Atheros QCA9531 v2. Short specification: - 550/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm - 2x MMCX connectors - mini-PCIe connector with PCIe/USB buses and SIM slot - 7x LED, 1x button, 1x optional buzzer - UART, (E)JTAG and LED headers Default configuration: - WAN on eth1 (RJ45 near DC jack) - LAN on eth0 (RJ45 near button) - S4 LED set to be status LED - all LEDs configurable form user space - button configured for reset Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: spi-rb4xx fix.Sergey Sergeev2016-07-021-1/+1
| | | | | | | | In new kernels we should use clk_prepare_enable instead of clk_enable since clk_enable does not make proper initialization that leads to rise WARN_ON messages and not working spi bus on the device. Signed-off-by: Sergey Sergeev <adron@yapic.net>
* ar71xx: prevent spurious ethernet resets from dma hang check false positivesFelix Fietkau2016-07-022-6/+12
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: disable pdata->use_flow_control for QCA9558Felix Fietkau2016-06-271-1/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: rename ethernet pdata->builtin_switch to use_flow_controlFelix Fietkau2016-06-273-8/+8
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Revert "ar71xx: prevent spurious ethernet resets from dma hang check false ↵Felix Fietkau2016-06-262-6/+5
| | | | | | positives" This reverts commit 3d58d7f053eae83b59baf5c8b8a58da78653f605.
* ar71xx: prevent spurious ethernet resets from dma hang check false positivesFelix Fietkau2016-06-262-5/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: enable flow control for ethernet MACs with built-in switchFelix Fietkau2016-06-263-1/+11
| | | | | | | | Should fix LAN speed issues on some devices. This is an updated version of the previously reverted commit with the same name. It improves the check for MACs connected to a built-in switch Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Revert "ar71xx/cpe510: use second wifi calibration table"Alexander Couzens2016-06-161-1/+1
| | | | | | | | Using the high power table can damage the device in some cases. This reverts commit bf27ac019c137e7baf90ca6ef0e40945ae871797. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* Revert "ar71xx: enable flow control for ethernet MACs with built-in switch"Felix Fietkau2016-06-141-9/+1
| | | | | | | | This reverts commit 1beb5bec6453abb220c5be4ddb9e6dc02d08d735. It was found to cause the WAN port to fail on some AR934x devices Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: mach-ubnt-xm.c convert patches to mach fileArne Zachlod2016-06-131-0/+700
| | | | Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* ar71xx: enable flow control for ethernet MACs with built-in switchFelix Fietkau2016-06-131-1/+9
| | | | | | Should fix LAN speed issues on some devices Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for OpenEmbed SOM9331Allan Nick Pedrana2016-06-074-0/+137
| | | | | | | | This patch adds the target profile SOM9331 and configures hardware functionality for the 3x Eth Ports & corresponding LED's, the USB Host, the USART to USB bridge and the System LED. Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
* treewide: replace nbd@openwrt.org with nbd@nbd.nameFelix Fietkau2016-06-076-6/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add WRTnode2Q supportKeLei Liang2016-06-064-0/+138
| | | | Signed-off-by: KeLei Liang <xzmu@wrtnode.com>
* ar71xx: Fix TL-WR841N v11 LEDs, use separate machineStijn Segers2016-05-312-1/+71
| | | | Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* ar71xx/cpe510: use second wifi calibration tableAlexander Couzens2016-05-231-1/+1
| | | | | | | The cpe510 has two calibration tables. The first calibration table requires to modify ath9k driver to work (patched tx gain table). Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510Alexander Couzens2016-05-232-6/+25
| | | | | | | Split profile into 2GHz and 5GHz. The 5GHz devices are quite "special". The 2 GHz works perfect. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: add kernel support for the OpenMesh MR1750v2Sven Eckelmann2016-05-232-0/+2
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add kernel support for the OpenMesh OM2P-HSv3Sven Eckelmann2016-05-232-0/+2
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx/cpe510: enable LNA for CPE210/220/510/520Alexander Couzens2016-05-201-0/+6
| | | | | | | The LNA improves the rx path. Within a simple test setup it improved the signal from -60dbm to -40dbm. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: fix DDR write buffer flushing issues with 4.4Felix Fietkau2016-05-151-73/+16
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for TP-LINK TL-WR842N/ND v3Cezary Jackiewicz2016-05-143-8/+105
| | | | | | | | | | | - CPU QCA9531-BL3A - RAM: 64MB - flash: 16MB - USB AP143 platform, similar to tl-wr841n v10/v11, but with USB Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ar71xx: add proper support for Archer-C7 V2John Crispin2016-05-142-4/+41
| | | | | | This has minor differences to the V1 Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: Fix TP-LINK Archer-C5/C7 v2 rfkillJohn Crispin2016-05-121-1/+1
| | | | | | Fix ARCHER_C7_GPIO_BTN_RFKILL, which is attached to GPIO23 Signed-off-by: Lars Buerding <lb.wrt@metatux.net>
* ar71xx: Add support for Ubiquiti UniFi AP AC PROP.Wassi2016-05-123-1/+72
| | | | | Add support for the Ubiquiti UniFi AP AC PRO Signed-off-by: P.Wassi <p.wassi at gmx.at>
* ar71xx: Rename unifiac to unifiac-liteP.Wassi2016-05-123-9/+9
| | | | | | | To avoid confusion with different unifiac devices, rename existing target "unifiac" to "unifiac-lite", before "unifiac-pro" is introduced. Signed-off-by: P.Wassi <p.wassi at gmx.at>
* ar71xx: add TP-Link TL-WR810N supportblogic2016-05-104-0/+147
| | | | | | | | | This patch adds support for the TP-Link TL-WR810N. https://wiki.openwrt.org/toh/tp-link/tl-wr810n Signed-off-by: Jens Steinhauser <jens.steinhauser@gmail.com> SVN-Revision: 49286
* ar71xx: Fix eth0 support for Ubiquiti UniFi AP ACblogic2016-05-101-0/+1
| | | | | | | Fix eth0 support for the Ubiquiti UniFi AP AC Signed-off-by: Paul Wassi <p.wassi at gmx.at> SVN-Revision: 49277
* ar71xx: Add support for the OMYlink OMY-G1rebootJohn Crispin2016-04-264-0/+135
| | | | | | | | | | https://wiki.openwrt.org/toh/omylink/omy-g1 http://www.omylink.com/ Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 49258
* ar71xx: fix build errorHauke Mehrtens2016-04-172-0/+2
| | | | | | | | | | This fixes a build error introduced in r49193. This closes #22230 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 49194
* ar71xx: fix build with kernel 4.4Hauke Mehrtens2016-04-172-0/+8
| | | | | | | | | | The file linux/mdio-gpio.h was moved to linux/platform_data/mdio-gpio.h in kernel 4.4 Reported-by: Arjen de Korte <arjen+openwrt@de-korte.org> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 49193
* ar71xx: add TP-Link TL-WA901ND-v4 supportJohn Crispin2016-04-094-0/+123
| | | | | | Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com> SVN-Revision: 49158
* ar71xx: add support for Compex WPJ342John Crispin2016-04-094-0/+190
| | | | | | | | | | | | OpenWrt can be flashed with following uboot commands: tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize Signed-off-by: Christian Mehlis <christian@m3hlis.de> SVN-Revision: 49157
* ar71xx: add kernel support for the OpenMesh OM5P-ACv2 boardJohn Crispin2016-04-094-0/+228
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49149
* ar71xx: add kernel support for the OpenMesh OM5P-AC boardJohn Crispin2016-04-094-0/+204
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49141
* ar71xx: WPN824N: enable buttonsJohn Crispin2016-04-011-5/+33
| | | | | | | | Enable buttons connected to the GPIOs of the AR9285. Signed-off-by: Hartmut Knaack <knaack.h@gmx.de> SVN-Revision: 49109
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 03:30:51 +0000