aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/files
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: fix ethernet MAC reset on DMA hangFelix Fietkau2016-01-131-38/+55
| | | | | | | | | Fully reset the chip like on a full up/down, but without the PHY statemachine restart. Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48228
* ar71xx: extend ethernet DMA stuck check to all ar724x (and newer) chipsFelix Fietkau2016-01-131-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48227
* ar71xx: fix ap152 supportFelix Fietkau2016-01-101-1/+0
| | | | | | | | | | - ethernet gigabit pll - switch configuration - sysupgrade Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 48187
* V2 ar71xx : Add Support for the Bitmain Antrouter R1John Crispin2016-01-014-0/+110
| | | | | | | | | | This patch adds support for the Bitmain Antrouter R1 http://wiki.openwrt.org/toh/bitmain/r1 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 48058
* ar71xx: Add support for AirTight Networks C-55John Crispin2015-12-234-0/+144
| | | | | | | | This patch is to add support for the AirTight Networks C-55 Access Point Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47973
* ar8216: rework/fix AR8337 MAC swap handlingFelix Fietkau2015-12-205-5/+0
| | | | | | | | | | | | | | In r45970 the MAC swap handling was made opt-in, however some boards have been forgotten during the conversion. Since the reference design uses this MAC swapping, and pretty much all known boards using this chip seem to do so too, enabling the swapping is a more reasonable default than leaving it disabled. Change the code to still allow boards to opt-out of this. Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47956
* ar71xx: Add ath79_register_m25p80_large to support >16MB SPI chipsFelix Fietkau2015-12-192-0/+9
| | | | | | | | | | The following patch is to add ath79_register_m25p80_large, which sets is_flash to false to support bit banging. This is needed on some 32MB+ SPI chips, such as the S25FL256S1 Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47952
* ar71xx: Kernel board definition for PowerCloud CR5000Felix Fietkau2015-12-194-0/+189
| | | | | | | | | | | | Kernel part of support for the PowerCloud Systems CR5000. The CR5000 is a dual-band 802.11n wireless router with 8MB flash, 64 MB RAM, (unused in stock firmware) USB 2.0 port, and five port gigabit ethernet switch. The CR5000 was sold as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47940
* ar71xx: Kernel board definition for PowerCloud CR3000Felix Fietkau2015-12-194-0/+173
| | | | | | | | | | | | Kernel part of support for PowerCloud CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM, a four port fast ethernet switch, and a fast ethernet wan port which was sold by PowerCloud Systems as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47939
* ar71xx: Kernel board definition for PowerCloud CAP324Felix Fietkau2015-12-194-0/+145
| | | | | | | | | | | | | | | Kernel part of support for PowerCloud CAP324 Cloud AP. The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for the CloudCommand service for 'cloud' based managment of large numbers access points. The CAP324 is a dual-band 802.11n wireless access point with 16MB flash and 128MB RAM and single gigabit ethernet port. It can be powered via PoE or a power adaptor. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47938
* ar71xx: add support for TRENDnet TEW-823DRUJohn Crispin2015-12-174-0/+193
| | | | | | | | | | | | | | Add support for TRENDnet TEW-823DRU: - cpu: QCA9558 @720MHz - flash: 16MB - ram: 256MB - 4+1 RJ45 100/1000Mbps - wifi: QCA9558 (bgn) and QCA9880-BR4A (ac) - 1x USB 2.0 Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 47927
* ar71xx: clean up ethernet tx queue after reset, wake queues when done - ↵Felix Fietkau2015-12-141-3/+8
| | | | | | | | fixes hangs reported in #18922 Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47892
* ar71xx: add support for Cisco's MR18John Crispin2015-12-124-0/+310
| | | | | | | | | | | This patch adds support for Cisco's MR18. Detailed instructions for the flashing the device can be found in the OpenWrt forum thread: <https://forum.openwrt.org/viewtopic.php?id=59248> Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47878
* ar71xx: reorganize target patches/files to make it possible to add boards ↵Felix Fietkau2015-12-113-0/+1814
| | | | | | | | without adding patch files Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47874
* ar71xx: on wnr2200, revert the mac0/mac1, the ethernet interfaces are ↵Felix Fietkau2015-12-111-3/+3
| | | | | | | | swapped. use MAC1 for wlan Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47873
* ar71xx: fix MAC address swapping on WNR2200 and fix the WLAN MAC addressFelix Fietkau2015-12-111-3/+4
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47871
* ar71xx: add LED driver NU801John Crispin2015-12-112-0/+434
| | | | | | | | | The MR18 uses a 3-channel 16-bit PWM Constant Current Driver for its status LED. Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47848
* ar71xx: Add support for Wallys DR344John Crispin2015-12-111-0/+184
| | | | | | | | This patch is for Wallys DR344 support under OpenWRT Signed-off-by: Philippe Duchein <wireless-dev@duchein.net> SVN-Revision: 47847
* ar71xx: add GL-Domino Pi support V3John Crispin2015-11-241-0/+136
| | | | | | | | This is the patch for GL-Domino Pi V3. Updated against the latest trunk. Signed-off-by: alzhao<alzhao@gmail.com> SVN-Revision: 47622
* ar71xx: add GL-AR300 support V3John Crispin2015-11-241-0/+103
| | | | | | | | This is the patch for GL-AR300 V3, tested against the latest trunk. Signed-off-by: alzhao<alzhao@gmail.com> SVN-Revision: 47621
* ar71xx: add GL-AR150 support V3John Crispin2015-11-241-0/+125
| | | | | | | | This is the 3rd version. Modified against the latest trunk. Signed-off-by: alzhao<alzhao@gmail.com> SVN-Revision: 47620
* ar71xx: add support for the devolo dLAN HotspotJohn Crispin2015-11-211-0/+117
| | | | | | Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> SVN-Revision: 47554
* ar71xx: add Arduino YunHauke Mehrtens2015-11-101-0/+137
| | | | | | | | | | | | | | | | | | | This is based on patches from Federico Fissore <f.fissore@arduino.cc> especially this one: https://github.com/arduino/openwrt-yun/commit/7e2976fa83fb0d72a955574499178c387a1b3c92 The console is running with 250000 baud which is a non standard baud rate and needs an extra patch to be applied, I will try to get this patch upstream or something else which accomplish the same. Some upstream code looks like there are many different versions of this SoC, are these only internal versions and all versions on the consumer market are the same? I saw different GPIO configuration and flash sizes of 8MB and 16MB? Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 47451
* ar71xx: add support for TP-LINK TL-WR941ND v6 (international version)Felix Fietkau2015-11-081-0/+149
| | | | | | | | | | | | | | | The international version is completely different from the already supported Chinese version. The WLAN of the QCA956x SoC used by this router has been fixed in r46948. This patch looks like it changes a lot in 700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately, quilt decided to completely reorganize the Kconfig patch even though only a single section has been added. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 47420
* ar71xx: Add support for ZyXEL NBG6616.Felix Fietkau2015-11-071-18/+123
| | | | | | Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net> SVN-Revision: 47405
* ar71xx: Bitmain Antminer S1/S3 set GPIO for USB PowerJohn Crispin2015-10-262-1/+6
| | | | | | | | | Antminers using the stock bootloader will not hash without this GPIO set. Applies to DD and CC Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 47261
* ar71xx: Send power to USB port on WNR2200John Crispin2015-10-191-4/+4
| | | | | | | | | | | | | This patch fixes ticket #15267 by enabling power on the WNR2200's USB port. At present, the USB port on the WNR2200 is non-functional due to it not receiving power. This patch defines an additional GPIO pin, but none of the current GPIO definitions have been modified. Signed-off-by: Riley Baird <BM-2cVqnDuYbAU5do2DfJTrN7ZbAJ246S4XiX@bitmessage.ch> SVN-Revision: 47236
* ar71xx: Add Gainstrong MiniBox v1.0 support to trunkJohn Crispin2015-10-191-0/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch supersedes the v1 from September 17th. Bumping the patch version - the MiniBox profile showed up under M, but since it's called 'Gainstrong MiniBox v1.0' now it looks out of place. Renamed the profile to gs-minibox-v1.mk to fix that. The following patch adds support for the Gainstrong MiniBox into trunk (or 'Designated Driver' :D ). Fixed items: - Inverted LED polarity (OOLITE seems to suffer from the same problem). - Changed uppercase MINIBOX_V1_ prefix as requested. - Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor). - Mention the vendor (Gainstrong) in code headers. Compiles fine, has been confirmed working by owners on 15.05. Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c, the MiniBox images build fine without, so I'm wondering: do I need to add it in there as well? Any added benefit? Thank you Signed-off by: Stijn Segers <francesco.borromini@inventati.org> SVN-Revision: 47234
* ar71xx: Bitmain Antminer S1 & S3 cleanupJohn Crispin2015-10-192-7/+7
| | | | | | | | | | | | Sets the LEDs to boardname:color:led-name Sets the LAN to eth0 Other corrections such as the Machine Name and HWIDs v2 corrects the profile names in the Makefile and changes tabs to spaces in the Makefile 'define Device/' like the other devices. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 47221
* ar71xx: Add WeIO Board SupportFelix Fietkau2015-09-241-0/+140
| | | | | | | | | | Add support for WeIO board (http://we-io.net). This board is based on Carambola2 board form 8Devices. Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups] SVN-Revision: 47036
* ar71xx: add support for ap152 reference boardJohn Crispin2015-09-161-0/+141
| | | | | | Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> SVN-Revision: 46972
* ath79: dev-eth: fix QCA9561 set phy interface mode and maskJohn Crispin2015-09-161-2/+7
| | | | | | | | | | QCA9563 and QCA9561 are two series of Qualcomm SoC Dragonfly. The only different is QCA9563 w/o internal switch. It has one GMAC with SGMII interface. But they have the same device ID(0x1150). So they share the same codes. Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> SVN-Revision: 46971
* ar71xx: add TP-LINK TL-WDR3320 v2 supportJohn Crispin2015-09-141-0/+146
| | | | | | | | | | This patch adds support for TP-LINK TL-WDR3320 v2. This router uses a chinese version 2 firmware header,. Signed-off-by: Weijie Gao <hackpascal@gmail.com> SVN-Revision: 46934
* ar71xx: add kernel support for the OpenMesh MR1750 boardJohn Crispin2015-09-141-0/+129
| | | | | | Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 46926
* target: ar71xx: add support for COMFAST CF-E316N v2 boardFelix Fietkau2015-09-111-0/+132
| | | | | | | | | | | | This adds full support (sans sysupgrading from vendor firmware) for the COMFAST CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is actively refusing to provide GPL'd sources for the OpenWrt version they ship with the device, damn them). Signed-off-by: Paul Fertser <fercerpav@gmail.com> SVN-Revision: 46852
* ar71xx: add support for TP-Link TL-WDR6500 v2John Crispin2015-08-171-0/+141
| | | | | | | | | | | Signed-off-by: Weijie Gao <hackpascal@gmail.com> This patch adds support for TP-Link TL-WDR6500 v2. The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for the whole firmware, so I have to create a new firmware creation method. SVN-Revision: 46663
* ar71xx: add 64kb bootloader mtd parser for tplinkpartJohn Crispin2015-08-171-6/+29
| | | | | | | | | | | Signed-off-by: Weijie Gao <hackpascal@gmail.com> This patch adds flash layout parser for TP-Link firmwares which have a 64kb bootloader. This is used for TP-Link TL-WDR6500 v2. SVN-Revision: 46662
* ar71xx: Add support for Black SwiftJohn Crispin2015-08-171-0/+83
| | | | | | | | | | | | Add support for the Black Swift board: http://www.black-swift.com/ Took relevant parts and slightly adapted from: https://github.com/blackswift/openwrt/blob/master/bsb.patch Signed-off-by: Bruno Randolf <br1@einfach.org> SVN-Revision: 46651
* ar71xx: add support for Onion OmegaJohn Crispin2015-07-241-0/+84
| | | | | | | | | | | | This patch adds support for the Onion Omega. https://onion.io/omega Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Acked-by: Boken Lin <bl@onion.io> Tested-by: Jacky Huang <huangfangcheng@163.com> SVN-Revision: 46458
* ar71xx: Add support for AP147-010 reference boardJohn Crispin2015-07-241-0/+125
| | | | | | Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 46457
* ar71xx: remove the use of the obsolete IRQF_DISABLED flag in the NAND flash ↵Felix Fietkau2015-07-201-1/+1
| | | | | | | | driver (fixes #20125) Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 46433
* Revert "ar71xx: Add support for Cisco-Linksys WAP4410N" (r46250)Felix Fietkau2015-07-191-285/+0
| | | | | | | | The commit is incomplete, it does not even build the mach-* file This reverts commit 6e6adcf7a197b1802cb728ddcccf05f890ca0574 SVN-Revision: 46425
* ar71xx: add support for the devolo dLAN pro 1200+ WiFi acJohn Crispin2015-07-141-0/+189
| | | | | | Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> SVN-Revision: 46342
* ar71xx: add support for the devolo dLAN pro 500 Wireless+John Crispin2015-07-141-0/+203
| | | | | | Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> SVN-Revision: 46338
* ar71xx: compex wpe72 add space to include statementJohn Crispin2015-07-091-1/+1
| | | | | | Signed-off-by: Christian Mehlis <christian@m3hlis.de> SVN-Revision: 46284
* ar71xx: compex wpj531 register usb supportJohn Crispin2015-07-091-0/+1
| | | | | | Signed-off-by: Christian Mehlis <christian@m3hlis.de> SVN-Revision: 46283
* ar71xx: compex wpj531 fix setting mac address on ethernetJohn Crispin2015-07-091-6/+5
| | | | | | Signed-off-by: Christian Mehlis <christian@m3hlis.de> SVN-Revision: 46282
* ar71xx: compex wpj531 fix ethernet registrationJohn Crispin2015-07-091-2/+2
| | | | | | | | | | | In fb6f62e97733312053ab593fcf68eea47a21169e several settings are set on the ethernet device, but they are not working. Fix Ethernet by setting the right values. Signed-off-by: Christian Mehlis <christian@m3hlis.de> SVN-Revision: 46281
* ar71xx: ag71xx remove IRQF_DISABLEDJohn Crispin2015-07-091-1/+1
| | | | | | | | | | no-op since 2.6.35 removed in Kernel 4.1 see https://lwn.net/Articles/380931/ Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> SVN-Revision: 46280
* ar71xx: Add support for Cisco-Linksys WAP4410NJohn Crispin2015-07-071-0/+285
| | | | | | | | | | This patch adds support for the Cisco WAP4410N, an access point that uses the AR9132 SoC. Web upgrades from stock are not yet possible, UART access required for the initial flash. Signed-off-by: Ryan A Young <rayoung@utexas.edu> SVN-Revision: 46250
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-04 17:54:14 +0000