aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/files/arch
Commit message (Collapse)AuthorAgeFilesLines
...
* ar71xx: rename COMFAST CF-E355AC to CF-E355AC v1Piotr Dymacz2018-02-221-12/+41
| | | | | | | | There are now supported two versions of the CF-E355AC board which differ in 802.11ac radio chip. Include version number in board, model, image filename, etc., also for the v1. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E355AC v2Ding Tengfei2018-02-223-3/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9531 + QCA9886. Short specification: - 2x 10/100 Mbps Ethernet, with PoE support - 128MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, 802.11b/g/n - 2T2R 5 GHz, 802.11ac/n/a, WAVE 2 - built-in 4x 3 dBi antennas - output power (max): 500 mW (27 dBm) - 1x RGB LED, 1x button - built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Ding Tengfei <dtf@comfast.cn> [updated kernel config for both boards] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2Peng Zhang2018-02-225-0/+356
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334. Specification: - 750/400/250 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11) - 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11) - 2x 10/100/1000 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (USB 2.0 bus only) - 1x microSIM slot - 1x USB 2.0 - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x 2-pos switch - 1x DC jack for main power input (9-48 V) - UART (J5) and LEDs (J13) headers on PCB WHQX E600G is based on Qualcomm QCA9531. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601) - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x microSIM slot - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11) - 2x 10/100 Mbps Ethernet - 6x LED (1x RGB, 5 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-12 V) - UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB Important notice: First version of these boards are using different mtd layout, with ART data at the end. You should not use v2 images on v1 board because it will result in lost of ART data! Flash instruction (using U-Boot CLI and tftp server): 1. Configure PC with static IP 192.168.1.10 and tftp server. 2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. 3. Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. 4. Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): 1. Configure PC with static IP 192.168.1.xxx(2-254)/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. 3. Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: Peng Zhang <sd20@qxwlan.com> [reworked: image generation code, mach-* files, commit description, fixed minor code style issues, rebased on master] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix typos and indentation in Kconfig.openwrtPiotr Dymacz2018-02-221-3/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: include vendor name for GL iNet productsKyson Lok2018-02-224-5/+4
| | | | | | | This patch include GL.iNet vendor name in the machine name for GL.iNet vendor products. Signed-off-by: Kyson Lok <kysonlok@gmail.com>
* ar71xx: uniform GL iNet products mach nameKyson Lok2018-02-222-2/+2
| | | | | | | The mach name of GL AR150 and GL AR300 is inconsistent with other products. Signed-off-by: Kyson Lok <kysonlok@gmail.com>
* ar71xx: add more registers to ar71x_regs.hJulien Dusser2018-02-131-11/+0
| | | | | | | | | | Add more registers and flags to ar71x_regs.h for QCA955x and QCA956x SoCs. Values come from Qualcomm Atheros u-boot code. Patches can be merged into 622-MIPS-ath79-add-more-register-defines-for-QCA956x-SoC.patch Signed-off-by: Julien Dusser <julien.dusser@free.fr>
* ar71xx: Add eTactica EG-200 supportKarl Palsson2018-02-134-0/+111
| | | | | | | | | | | | | | EG-200 is a DIN rail mountable device with one ethernet port, wifi, an RS-485 port, and an internal USB attached uSD card reader. Two leds, "modbus" and "etactica" are managed by userspace applications in factory firmware. Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ar71xx: add support for TP-Link RE355Henryk Heisig2018-02-134-5/+69
| | | | | | | | | | | | | | | | | | | | | | | | This device is identical as TP-Link RE450 RE355 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9558+QCA9880. Specification: 720/600/200 MHz (CPU/DDR/AHB) 64/128 MB of RAM (DDR2) 8 MB of FLASH (SPI NOR) 3T3R 2.4 GHz 3T3R 5 GHz 1x 10/100/1000 Mbps Ethernet 7x LED, 3x button UART header on PCB Flash instruction: Web: Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use OEM System Tools - Firmware Upgrade site. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx:add support for COMFAST CF-E375ACDing Tengfei2018-02-114-0/+117
| | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337. Short specification: 2x 10/100/1000 Mbps Ethernet, with PoE support 128MB of RAM (DDR2) 16 MB of FLASH 3T3R 2.4 GHz, 802.11b/g/n 2T2R 5 GHz, 802.11ac/n/a, wave 2 built-in 5x 3 dBi antennas output power (max): 500 mW (27 dBm) 1x RGB LED, 1x button built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Ding Tengfei <dtf@comfast.cn>
* ar71xx: add ew-balin platform from Embedded WirelessCatrinel Catrinescu2018-01-254-0/+123
| | | | | | | | | | | | | | | | | | | Add the Embedded Wireless "Balin" platform SoC: QCA AR9344 or AR9350 RAM: DDR2-RAM 64MBytes Flash: SPI-NOR 16MBytes WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n Ethernet: 3 x 10/100 Mb/s USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up PCI-Express: 1 x lane PCIe 1.2 UART: 1 x Normal, 1 x High-Speed JTAG: 1 x EJTAG GPIO: 10 x Input/Output multiplexed The module comes already with the current vanilla OpenWrt firmware. To update, use "sysupgrade" image directly in vendor firmware. Signed-off-by: Catrinel Catrinescu <cc@80211.de>
* ar71xx: add support for the MikroTik RB911-2Hn/5Hn boardsGabor Juhos2018-01-223-0/+100
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for the MikroTik RB911-2Hn (911 Lite2) and the RB911-5Hn (911 Lite5) boards: https://mikrotik.com/product/RB911-2Hn https://mikrotik.com/product/RB911-5Hn The two boards are using the same hardware design, the only difference between the two is the supported wireless band. Specifications: * SoC: Atheros AR9344 (600MHz) * RAM: 64MiB * Storage: 16 MiB SPI NOR flash * Ethernet: 1x100M (Passive PoE in) * Wireless: AR9344 built-in wireless MAC, single chain 802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn) Notes: * Older versions of these boards might be equipped with a NAND flash chip instead of the SPI NOR device. Those boards are not supported (yet). * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the same hardware. Support for that can be added later with little effort probably. Installation: 1. Setup a DHCP/BOOTP Server with the following parameters: * DHCP-Option 66 (TFTP server name): pointing to a local TFTP server within the same subnet of the DHCP range * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename of the to be booted image. The usable intramfs files are: - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin 2. Press the reset button on the board and keep that pressed. 3. Connect the board to your local network via its ethernet port. 4. Release the button after the LEDs on the board are turned off. Now the board should load and start the initramfs image from the TFTP server. 5. Upload the sysupgrade image to the board with scp: $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin 5. Log in to the running system listening on 192.168.1.1 via ssh as root (without password): $ ssh root@192.168.1.1 7. Flash the uploaded firmware file from the ssh session via the sysupgrade command: root@OpenWrt:~# sysupgrade /tmp/fw.bin Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: mach-rbspi: return rb_info from rbspi_platform_setupGabor Juhos2018-01-221-13/+13
| | | | | | | | | | | | Modify the rbspi_platform_setup() function to return the pointer of the rb_info structure. This allows board specific setup routines to access the various fields of the information. It is useful for investigating the hardware option bits for example. Also update the board setup codes, to ensure that those handle the new return value correctly. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: add definitions for RouterBOARD hardware option bitsGabor Juhos2018-01-221-0/+26
| | | | | | | | | | | | Add bit definitions for the 'hardware options' tag which is used in the MikroTik devices' hardware configurations. These values can be used in board setup codes, to do different initialization sequences. The values were obtained from the RouterOS 6.41-rc38 patches. Additionally, introduce two helper functions what make the processing of the hardware options easy. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: drop mdio-gpio.h include from mach-om5pacv2.cGabor Juhos2018-01-171-6/+0
| | | | | | | | | | | | | | The setup code of the OpenMesh OM5P ACv2 device uses nothing from the mdio-gpio.h header, so remove the inclusion of that. Also remove the kernel version check which is needed only because the mdio-gpio.h header exists in a different path in older kernels. Compile tested only. Cc: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: mach-rbspi: simplify reset button registrationGabor Juhos2018-01-171-64/+30
| | | | | | | | | | | | The setup code defines four individual structures for the Reset buttons of the supported boards. The only difference between the definitions is the GPIO number used for the button. Replace the different structures with one generic variant, and add a helper function to simplify the button registration. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)Roger Pueyo Centelles2018-01-152-3/+95
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info. Specifications: - SoC: Qualcomm Atheros QCA9556 - RAM: 64 MB - Storage: 16 MB NOR - Wireless: · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive PoE in Working: - Board/system detection - Sysupgrade - Serial console - Ethernet - 2.4 GHz radio - 5 GHz radio - Reset button Not working: - LEDs (added according to Mikrotik's GPL sources but not functional) Unsupported: - ZT2046Q SPI temperature and voltage sensor Contributors: Giuseppe Tipaldi (@Ciusss89) Ricky (@rickydee) Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
* ar71xx: add support for GL.iNet GL-AR750Piotr Dymacz2018-01-154-0/+159
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750. Specification: - 650/597/216 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3x 10/100 Mbps Ethernet - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 1x USB 2.0 (power controlled by GPIO) - 1x microSD (GL857L) - 3x LED (all driven by GPIO) - 1x button (reset) - 1x 2-pos switch - header for optional PoE module - 1x micro USB for main power input - UART + I2C header on PCB Flash instruction: Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used to flash OpenWrt/LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix Sitecom WLR-8100 supportDavide Fioravanti2018-01-151-12/+2
| | | | | | | | | | | | | | This patch fixes Sitecom WLR-8100: - mtd layout - LAN and WAN MAC address setup - 2.4 GHz Wi-Fi MAC address setup - 5 GHz Wi-Fi support (calibration data, MAC address setup, missing ath10k-* packages) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [squashed commits, fixed whitespace issues, reworded commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network R36APiotr Dymacz2018-01-154-0/+152
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36A is a successor of the previous model, the R36 (Ralink RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2. Specification: - 650/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB - 1x USB 2.0 (power controlled by GPIO) - 6x LED (5 of them are driven by GPIO) - 2x button (reset, wifi/wps) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - DC jack for main power input (12 V) - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Teltonika RUT900Piotr Dymacz2018-01-154-0/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is an industrial 3G router based on Atheros AR9344. There are available 3 other models in RUT9xx series: RUT905, RUT950 and RUT955, which differ in availability of additional I/O ports, built-in GSM modem type, GPS antenna and other features. FCC ID of the RUT950 model (LTE module built-in): 2AET4-RUT950. This patch adds support for the RUT900 model only but can be easily extended to cover whole series. Also, as there are several different 3/4G modules (Huawei, Quectel, Telit) used in whole series, packages required for WWAN support are not included by default. It is up to the user to install required software for built-in modem. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA - built-in 3G module (example: Telit HE910-D) - 2x miniSIM slot - 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G) - PCA9539 16-bit GPIO I2C expander - 12x LED (4 are driven by AR9344, 7 by PCA9539) - 1x button (reset) - DC jack for main power input (9-30 V) - UART available on PCB edge connector Serial console pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1". Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network N5QPiotr Dymacz2018-01-144-0/+142
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network N5Q is a successor of previous model, the N5 (outdoor CPE/AP, based on Atheros AR7240 + AR9280). New version is based on Atheros AR9344. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm - 8x LED (7 are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - header for optional 802.3at/af PoE module - DC jack for main power input (optional, not installed by default) - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmare which is based on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network AP91-5GPiotr Dymacz2018-01-144-0/+129
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros AR7240 + AR9280. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 32 MB of RAM (DDR1) - 8 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm - 6x LED (5 are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - header for optional 802.3at/af PoE module - DC jack for main power input (optional, not installed by default) - UART and LEDs headers on PCB Flash instruction: Use "factory" image in vendor GUI (in case of problems, make sure your board has up to date firmware). Alternatively, TFTP in U-Boot can be used: select option "2. Load system code then write to Flash via TFTP" during early boot and use "sysupgrade" image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: remove obsolete '< KERNEL_VERSION(4, 4, 0)' checkGabor Juhos2018-01-091-5/+0
| | | | | | | | | Because the oldest supported kernel version on the ar71xx target is 4.4, the condition that the kernel version is smaller than 4.4.0 is always false. Remove the obsolete check from mach-rb4xx.c to clean up the code a bit. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: remove obsolete '< KERNEL_VERSION(3, 15, 0)' checksGabor Juhos2018-01-091-5/+0
| | | | | | | | | Because the oldest supported kernel version on the ar71xx target is 4.4, the condition that the kernel version is smaller than 3.15.0 is always false. Remove the obsolete checks from the target specific source files to clean up the code a bit. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ag71xx: Fix rx ring buffer stall on small packets flood on qca956x and qca953x.Vittorio Gambaletta2017-12-292-1/+6
| | | | | | Backported from Code Aurora QSDK Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
* ar71xx: add support for MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s)Roger Pueyo Centelles2017-12-211-3/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac wireless router. Additionally, it adds a new profile for devices with >= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget. See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info. Specifications: - SoC: Qualcomm Atheros QCA9558 (720 MHz) - RAM: 128 MB - Storage: 128 MB NAND - Wireless: external QCA9822 802.11a/ac 2x2:2 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in - SFP: 1x host Working: - Board/system detection - NAND storage detection - Wireless - Ethernet - 1x user LED - Reset button - Sysupgrade Untested: - SFP cage (probably not working) Installation: - Boot initramfs image via TFTP and then flash sysupgrade image Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ar71xx: fix spelling in mach-rb922.cRoger Pueyo Centelles2017-12-211-1/+1
| | | | Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ar71xx: fix rb922gs_nand_scan_fixup()Roger Pueyo Centelles2017-12-211-1/+5
| | | | | | | | | Apply code from commits 9e1bc27e6d67fa29791eb0fac5e5f0066d12a761 (ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and 665bb2749906aff4d4ec607a308353fa30cb1b3a (ar71xx: fix invalid pointer dereference in rb95x_nand_scan_fixup()) to RB92x devices too. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ar71xx: fix invalid pointer dereference in rb95x_nand_scan_fixup()Gabor Juhos2017-12-161-0/+4
| | | | | | | | | | | | Since Linux 4.6, mtd->priv no longer points to the NAND specific structure. Under 4.9 it contains NULL, thus using it to access chip->options causes an invalid pointer dereference (FS#1200). Update the code to use the mtd_to_nand() helper under 4.9 to obtain the address of the chip specific data. Fixes: 7bbf4117c6fe ("ar71xx: Add kernel 4.9 support") Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: fix invalid pointer dereference in c60_nand_scan_fixup()Gabor Juhos2017-12-151-0/+4
| | | | | | | | | | | | | | | | Since Linux 4.6, mtd->priv no longer points to the NAND specific structure. Under 4.9 it contains NULL, thus using it to access the fields of the nand_chip structure causes an invalid pointer dereference. Update the code to use the mtd_to_nand() helper under 4.9 to obtain the address of the chip specific data. Compile tested only. Fixes: 7bbf4117c6fe ("ar71xx: Add kernel 4.9 support") Signed-off-by: Gabor Juhos <juhosg@freemail.hu> Tested-by: Christian Lamparter <chunkeey@gmail.com>
* ar71xx: fix LED name typo for GL-AR300Mkyson Lok2017-12-151-1/+1
| | | | | | It shouldn't use double colon characters. Signed-off-by: kyson Lok <kysonlok@gmail.com>
* Revert "ar71xx: TL-WR1043N v4/v5: add orange WAN LED support"John Crispin2017-12-141-19/+3
| | | | | | | | | | This reverts commit 256990cbc0157feb8a9f37efeebf0330ab73727f. this commit caused a compile error "TL_WR1043_V5_GPIO_LED_WANORANGE" is undefined. Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: TL-WR1043N v4/v5: add orange WAN LED supportTim Thorpe2017-12-141-3/+19
| | | | | | | Add missing definitions for the orange WAN LED on the TL-WR1043N(D) v4 and v5. Minor format correction on a constant for consistency. Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
* ar71xx: C58/C59 fix LAN1 working incorrectlyDavid Bauer2017-12-081-1/+1
| | | | | | | This commit fixes LAN Port 1 not transferring data in case no other LAN Port has active link-state on TP-Link Archer C58/C59. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: merge mach-files for TP-Link TL-WR802N v1 and v2Paul Wassi2017-11-143-131/+53
| | | | | | | TP-Link TL-WR802N v1 and v2 are set up with almost same configuration in the mach-files. Merge the mach-files of these devices. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: add support for TP-Link TL-WR1043N v5Tim Thorpe2017-11-143-0/+92
| | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4, except that the USB port has been removed and there is no longer a removable antenna option. The software is more in line with the Archer series in that it uses a nested bootloader scheme. Specifications: - QCA9563 at 775 MHz - 64 MB RAM - 16 MB flash - 3 (non-detachable) Antennas / 450 Mbit - 1x/4x WAN/LAN Gbps Ethernet (QCA8337) - reset and Wi-Fi buttons Signed-off-by: Tim Thorpe <tim@tfthorpe.net> Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* ar71xx: add support for TP-Link TL-WA901ND v5Paul Wassi2017-11-142-1/+5
| | | | | | | | The TL-WA901ND v5 has the same hardware as v4, although the PCB has a different layout. Installation from factory is done via TFTP. (rename -factory image to wa901ndv4_tp_recovery.bin for tftp) Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: complete support for RB mAP 2nDRobert Marko2017-11-142-8/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD mAP 2nD https://mikrotik.com/product/RBmAP2nD Specifications: - SoC: Qualcomm QCA9531 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: builtin QCA9531, 2x2:2 - Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2) - USB: microUSB type AB port This patch adds missing code to fully support mAP. Machfile already contained configuration for mAP 2nD, but device specific configuration like LEDs etc., was missing. Note: The POE LED works but doesn't turn on when POE passthrough is enabled, despite being configured with GPIO trigger. Installation 1. Login to the Mikrotik WebUI to backup your licence keys 2. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. Connect the port labeled internet to your local network 4. Keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started LEDE via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ar71xx: complete support for RB wAP 2nDRobert Marko2017-11-142-3/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD wAP https://mikrotik.com/product/RBwAP2nD Specifications: - SoC: Qualcomm QCA9533 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: built-in QCA9533, 2x2:2 - Ethernet: 1x100M (802.3af/at POE in) This patch adds missing code to fully support wAP. Machfile already contained configuration for wAP 2nD but device specific configuration like LEDs etc. was missing. Installation: 1. Login to the Mikrotik WebUI to backup your licence keys 2. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. Connect the port labeled internet to your local network 4. Keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started LEDE via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ar71xx: add support for TP-Link TL-WR810N v2Paul Wassi2017-11-144-13/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR810N v2 is a compact Wi-Fi router with two Ethernet ports. Specification: - QCA9533 (650 MHz) - 32 MB RAM - 8 MB Flash - 300 Mbps Wi-Fi 2.4 GHz - 2x 10/100 Mbps Ethernet (eth0, eth1) - UART on testpads on PCB - 1x LED (GPIO-controlled) - 1x reset/WPS button - 1x slide-switch with 2 GPIO inputs Flash instructions: - Flash as regular firmware update in Web UI - Default: 192.168.0.254 / admin / admin - Select *-factory.bin When holding reset button during power-up, U-Boot requests a file 'wr810nv1_tp_recovery.bin' from TFTP server at 192.168.0.66 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: add support for Wallys DR342Piotr Dymacz2017-11-144-45/+104
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342. Short specification: - 560/450/225 MHz (CPU/DDR/AHB) - 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V) - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm - 2x MMCX connectors - miniPCIe connector with PCIe and USB 2.0 buses - optional miniSIM slot - 7x LED, 1x button - UART, (E)JTAG and LED headers - 1x DC jack for main power (12-56 V) Flash instruction (do it under U-Boot, using UART): 1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix typo in Kconfig.openwrtPiotr Dymacz2017-11-141-1/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix section mismatch in TP-Link Archer C7 v4 supportFelix Fietkau2017-11-051-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix LED config for DIR-869 A1Florian Beier2017-11-031-7/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes the LED configuration for the D-Link DIR-869 A1. In order to support the device I probed around using an initramfs image for the UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them. GPIO 16 set to low meant that the color was white while pulling it to high made the color change to orange. The past code was written based upon these findings. However, running a flashed image I now discovered that GPIO 15 controls the orange LEDs while GPIO 16 controls the white ones and that both are active when low. This means that the GPIOs were inverted and one active_low was set wrong which this patch fixes. Behavior of the LED front after this patch is applied: cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness 0 -> white LEDs are OFF 255 -> white LEDs are ON cat /sys/devices/platform/leds-gpio/leds/d-link:orange:status/brightness 0 -> orange LEDs are OFF 255 -> orange LEDs are ON If the brightness of both is set to 255 the LED front will be white. If the brightness of both is set to 0 the LED front will be off. Signed-off-by: Florian Beier <beier.florian@gmail.com>
* ar71xx: wzr-hp-ag300h: drop unused wmac led_pin settingsMathias Kresin2017-11-031-3/+0
| | | | | | | | | The GPIOs are used for defined LEDs and therefore are ignored/unset in the ath9k driver since 192f0a3db859. The wireless led led trigger is added in userspace since e20965811db6, which makes the ap9x_pci_setup_wmac_led_pin() superfluous. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: mach-rbspi: fix 74x164 supportThibaut VARENE2017-11-031-0/+1
| | | | | | | | | | | | | The platform data was missing the num_registers element which is now mandatory in linux 4.9 Without this patch, the gpio probing would fail with: gpio gpiochip1: (74x164): tried to insert a GPIO chip with zero lines Fixes: #1106 Tested-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: fix LED names for GL-AR150Paul Wassi2017-10-251-3/+3
| | | | | | | Add the respective colour to the LED's names for the GL-AR150 to be conform to the kernel. Also add netdev triggers for the LAN and WAN LED. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: fix secondary gpio controller base valuesFelix Fietkau2017-10-245-29/+29
| | | | | | | | In 4.9, gpio count is rounded up to 32 due to the use of bgpio in the ath79 gpio controller driver. Fix base values in mach files to account for that Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for TP-LINK Archer C7 v4Felix Fietkau2017-10-194-0/+263
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros QCA9561+QCA9888. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction: 1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin and rename it to ArcherC7v4_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f040000 +$filesize 3. cp.b $fileaddr 0x9f040000 $filesize 4. reset Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 10:04:01 +0000