| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Instead of renaming the default wireless led attached to the wireless
chip, add a new led using the platform leds with the phy0tpt trigger
set in userspace.
When switching ar71xx to device tree, the same can be done by using the
build in GPIO controller and without adding new bindings.
Drop the now unused platform code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
| |
Enable buttons connected to the GPIOs of the AR9285.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 49109
|
|
|
|
|
|
|
|
|
| |
Make use of ap9x_pci_setup_wmac_led_name() to set the name of the WLAN
LED.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 49108
|
|
|
|
|
|
|
|
|
| |
This patch provides full GPIO support for WNR1000v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49076
|
|
|
|
|
|
|
|
|
|
|
| |
Fix for invalid/random WLAN MAC address in WNR1000v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3
and WNR612v2.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49051
|
|
|
|
|
|
|
|
|
| |
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48924
|
|
|
|
|
|
|
|
|
| |
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48922
|
|
|
|
|
|
|
|
|
|
| |
Fix for invalid/random WLAN MAC address in WNR612v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48779
|
|
|
|
|
|
|
|
|
|
| |
Fix for invalid/random WLAN MAC address in WNR2000v3. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48777
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for Netgear WPN824N.
Hardware specs:
* AR7240, 4 LAN ports, 1 WAN port
* AR9285 WLAN
* 32 MB RAM
* 4 MB Flash
* 16 LEDs (LAN, WAN and Power/Status contain two LEDs for dual color
effect)
* 3 Buttons (not supported)
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48356
|
|
|
|
|
|
|
|
|
|
|
| |
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38101
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Netgear WNR612 v2:
- cpu Atheros AR7240 (Python) @400MHz
- flash 4MB
- ram 32MB
- ethernet 10/100: 1xwan + 2xlan (only two)
- radio AR9285
[juhosg: use a separate kernel patch]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3876/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37575
|
|
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36459
|