aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/config-4.4
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: add support for Nokia WI2A-AC200iFelix Fietkau2017-10-191-0/+1
| | | | | | | | | | | | | | | | | Specifications: - SoC: Qualcomm QCA9558 (720 MHz) - RAM: 256MB - Storage: 1MB NOR, 128 MB NAND flash - Ethernet: 1x1000M Installation: 1. Connect to serial console on the board 2. Boot initramfs image over u-boot 3. Copy image to the device and run sysupgrade Installation without serial console is not supported at this time Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: unify CONFIG_CMDLINEFelix Fietkau2017-09-281-1/+1
| | | | | | | Booting from jffs2 directly is no longer supported, use rootfstype=squashfs consistently for all subtargets Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for COMFAST CF-E355ACEnrique Giraldo2017-09-101-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9531 + QCA9882. Short specification: - 2x 10/100 Mbps Ethernet, with PoE support - 64MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, 802.11b/g/n - 2T2R 5 GHz, 802.11ac/n/a - built-in 4x 3 dBi antennas - output power (max): 500 mW (27 dBm) - 1x RGB LED, 1x button - built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net> [whitespace fixes, ac radio caldata offset fix] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for GL.iNet GL-USB150Piotr Dymacz2017-09-101-0/+1
| | | | | | | | | | | | | | | | | | | | | GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4) - 1T1R 2.4 GHz - 2x LED, 1x button - UART header on PCB Flash instruction: Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used to flash LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network AP121FPiotr Dymacz2017-07-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users. Device is based on Atheros AR9331 WiSoC and is running a custom version (updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR1) - 16 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet - 1T1R 2.4 GHz - 1x microSD (optional, on separate PCB) - 3x LED, 1x button, 1x switch - UART header on PCB Flash instruction (under U-Boot web recovery mode): 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with RJ45 port, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link TL-WR902AC v1Piotr Dymacz2017-07-041-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of TL-MR3020 (both devices use very similar enclosure, in same size). New device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (GPIO-controlled power) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch - UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper resitors are missing on TX/RX lines) - 1x micro USB (for power only) Flash instructions: Use "factory" image under vendor GUI. Recovery instructions: This device contains tftp recovery mode inside U-Boot. You can use it to flash LEDE (use "factory" image) or vendor firmware. 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin" to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir. 3. Connect PC with LAN port, press the reset button, power up the router and keep button pressed until WPS LED lights up. 4. Router will download file from server, write it to flash and reboot. Root access over serial line in vendor firmware: root/sohoadmin. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: generic: enable CONFIG_MTD_SPLIT_TPLINK_FWPiotr Dymacz2017-07-041-0/+1
| | | | | | | | We can use "tplink-fw" mtd splitter for TP-Link devices which use kernel with TP-Link header embedded inside "safeloader" image type and thus get rid of statically defined "kernel" and "rootfs" partitions in cmdline. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: refresh and cleanup target kernel configPiotr Dymacz2017-07-041-9/+9
| | | | | | | Refresh target kernel config and disable kernel support for all boards which belong to nand and mikrotik subtargets only. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link Archer C58 v1Henryk Heisig2017-06-291-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 6x LED, 3x button - UART header on PCB, RX, TX at TP4+5 (backside) QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to patch macaddress. Flash instruction: Use "factory" image directly in vendor GUI. Recovery method: 1. Set PC to fixed ip address 192.168.0.66/24. 2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and rename it to "tp_recovery.bin". 3. Start a tftp server with the file "tp_recovery.bin" in its root directory. 4. Turn off the router. 5. Press and hold Reset button. 6. Turn on router with the reset button pressed and wait ~15 seconds. 7. Release the reset button and after a short time the firmware should be transferred from the tftp server. 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin erase 0x9f020000 +$filesize cp.b $fileaddr 0x9f020000 $filesize reset This commit is based on GitHub PR#1112 Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for TP-Link TL-WA855RE v1Federico Cappon2017-06-291-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/397/198 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x external antennas - 2x LED (green and orange in the same package), 2x button - UART: TP5(TX) and TP4(RX) test points on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in EU version of the device, but should work also with the same device version sold in other countries. Signed-off-by: Federico Cappon <dududede371@gmail.com>
* kernel: cleanup CONFIG_SCHED_HRTICKStijn Tintel2017-06-291-1/+0
| | | | | | | Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the generic config in b47fd7656336162360ebf66147326763ddae3f8d. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx: add AVM FRITZ!WLAN Repeater 300E supportMathias Kresin2017-06-241-0/+3
| | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: AR7242 (Virian 400MHz) * RAM: 64 MB DDR (W9751G6JB-25) * Flash: 16MB SPI flash (S25FL129PIF) * WiFi: AR9382 (2.4/5GHz) + 2x SE2595L * LAN: 1x1000M (PEF7071V) To install LEDE via EVA bootloader, a FTP connection need to be established to 192.168.178.1 within the first seconds after power on: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: add support for TP-Link Archer C25 v1Ludwig Thomeczek2017-06-111-0/+1
| | | | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net> [minor code style fixes, boards alphabetical order fixes, reworked commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link TL-WR942N v1Serg Studzinskii2017-06-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on Qualcomm/Atheros QCA9561. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x USB 2.0 - 11x LED (most are controlled by 74HC595) - 2x button - UART header on PCB* * Serial console is disabled in OEM non-beta firmwares and corresponding GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by production (non-beta) U-Boot and firmware. Currently not working: 1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs by some U-Boot versions. Flash instruction under vendor GUI: 1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin". 2. Go to WEB interface and perform usual firmware upgrade. FLash instruction under U-Boot recovery mode (doesn't work in beta firmware): 1. Setup PC with static IP "192.168.0.66/24" and tftp server. 2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make it available to download from your tftp server. 3. Press "reset" button and power up the router, wait till "WPS" LED turns on. Flash instruction under U-Boot, using UART (can be done only with preinstalled UART-enabled U-Boot version!): 1. Use "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Serg Studzinskii <serguzhg@gmail.com> [minor code style fixes, extended commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for EnGenius ENS202EXTMarty Plummer2017-05-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius ENS202EXT is an outdoor wireless access point with 2-port 10/100 switch, detachable antennas and proprietery PoE. The device is based on Qualcomm/Atheros AR9341 v1. Specifications: - 535/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM - 16 MB of FLASH - UART (J1) header on PCB (unpopulated) - 2x 10/100 Mbps Ethernet - 2.4 GHz, up to 26dBm - 2x external, detachable antennas - 7x LED, 1x button Flash instructions: You have three options: - Use the vendor firmware upgrade page on the web interface and give it the factory.img. This is the easiest way to go about it. - If you have serial access during u-boot, interrupt the normal boot (any key before timeout) and run 'run failsafe_boot'; this will bring you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've bricked the normal firmware. - Use the vendor's management cli, which can be accessed via telnet with the same credentials as the web login (default admin:admin), then issue the following commands: *** Hi admin, welcome to use cli(V-1.6.7) *** ---========= Commands Help =========--- stat -- Status sys -- System wless2 -- 2.4G-Wireless mgmt -- Management tree -- Tree help -- Help reboot -- Reboot ens202ext>mgmt Management ---========= Commands Help =========--- admin -- Administration mvlan -- Management VLAN settings snmp -- SNMP settings backup -- Backup/Restore settings autorb -- Auto reboot settings fwgrade -- Firmware upgrade time -- Time settings wifisch -- Wifi schedule log -- Log diag -- Diagnostics disc -- Device Discovery logout -- Logout help -- Help exit -- Exit ens202ext/mgmt>fwgrade Management --> Firmware upgrade ---========= Commands Help =========--- fwup -- Firmware upgrade help -- Help exit -- Exit ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
* ar71xx: Add support for TP-Link MR6400Filip Moc2017-05-271-0/+1
| | | | | | | | | | | | | | | | | You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin on 192.168.0.66/24, connect to any ethernet port and power on device while holding the reset button). Flashing via OEM web interface does not work. Hardware Specification (v1.0 EU): - SoC: QCA9531 - Flash: Winbond W25Q64FV (8MiB) - RAM: EtronTech EM6AB160TSE-5G (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 2NIC (3x100M + 1x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 12V 1A Signed-off-by: Filip Moc <lede@moc6.cz>
* Revert "ar71xx: Add support for Teltonika RUT900"John Crispin2017-05-181-2/+0
| | | | | | | | This reverts commit 224e5f5efa22b8a0132522367afd3b22f05d53e1. pepe2k pointed out that this was not ready to merge Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: Add support for Teltonika RUT900Steffen Weinreich2017-05-181-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet ports, I/O, RS232, RS485, GPS. The device ist based on a Atheros AR9344 rev 3, Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM - 16 MB of FLASH - Serial Console header on a Card Board edge connector - 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN) - 2.4 GHz Wifi - 2x external, detachable Wifi antennas - LTE Modem Huawei ME909u-521 (Also other Modem seen) - 2x LTE antennas - 1x GPS antenna - 7x LED, 1x button - 1x USB Connector - 1x Serial RS232 - 1x Serial RS485 - 1x MicroSD Card The GPL sources of the device are available at www.teltonika.lt/gpl/ and are based on OpenWRT Barrier Breaker (14.07) Running from tftp: The Router starts into the uboot Webupdater if the Button ist pressed more than 3 seconds, if no Network cable is attached it starts the uboot serial console, from there the router loads the firmware image via tftpboot from 192.168.1.2:firmware.bin (the router has the 192.168.1.1). With bootm the loaded image will be booted. Signed-off-by: Steffen Weinreich <steve@weinreich.org>
* ar71xx: add support for Aerohive AP-121Chris Blake2017-05-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for Aerohive AP-121 access point. Specification: - SoC: Atheros AR9344-BC2A at 560MHz - WiFi 1: 2.4GHz Atheros AR9340? - SoC - WiFi 2: 5.0GHz Atheros AR9382-AL1A - Memory: 128MB from 2x Nanya NT5TU32M16DG-AC - SPI: 1MB Macronix MX25L8006E - NAND: 128MB Hynix H27U1G8F2BTR-BC - Ethernet: Atheros AR8035-A - USB: 1x 2.0 - TPM: Atmel SC3204 Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, download and flash LEDE factory image over tftp: dhcp; setenv serverip tftp-server-ip; tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin; nand erase 0x800000 0x800000; nand write 0x81000000 0x800000 0x800000; reset; Signed-off-by: Chris Blake <chrisrblake93@gmail.com> [minor text changes in commit subject and description, fixed alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh, fixed code style issues in mach-hiveap-121.c, ubinized factory image] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for 8devices Rambutan development boardMantas Pucka2017-05-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rambutan is a Wifi module based on QCA9550/9557 http://www.8devices.com/products/rambutan This commit adds basic support for Rambutan development kit Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of DDR2 RAM - 128 MB of NAND Flash - 1x 100Mbps Ethernet - 1x 1000Mbps Ethernet (PHY on dev-kit) - 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz - 2x U.FL connectors on module, chip antennas on dev-kit - 1x miniPCIe slot - 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header Flash instructions: Stock firmware is OpenWrt, so use: sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar or upgarde from GUI (don't save config) Use factory image to flash from U-Boot: tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi nand erase.part ubi nand write 80060000 ubi ${filesize} Signed-off-by: Mantas Pucka <mantas@8devices.com> [split support in uboot-envtools package into a separate commit, fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: Compex WPJ563 supportChristian Mehlis2017-03-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc) - RAM: 128 MiB - Storage: 16MB NOR flash - Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO - Ethernet: 2x1G Tested and working: - ethernet / switch / lan / wan - 2.4GHz SoC wifi - PCIe - leds - buzzer Ramload: - tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin - bootm 0x84000000 Install: - tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin - erase 0x9f030000 +$filesize - erase 0x9f680000 +1 - cp.b $fileaddr 0x9f030000 $filesize Erasing 0x9f680000 is required because uboot defines "bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot the higher address. I think the 16 mb flash are intended to be used as 8+8mb for a fallback image. In my hardware only the lower address has a bootable image. But to make sure future hardware will boot lede too, I erase one block, so uboot will skip this address. Signed-off-by: Christian Mehlis <christian@m3hlis.de>
* ar71xx: add support for P&W R602N and CPE505NPiotr Dymacz2017-03-231-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-LINK TL-WR840N v2 and v3Vaclav Svoboda2017-03-231-0/+1
| | | | | | | | | | | | | | This patch adds support for the TP-LINK TL-WR840N v2 and v3. - SoC: Qualcomm QCA9533-BL3A (650 MHz) - RAM: 32 MiB (Zentel A3S56D40GTP) - Flash: 4 MiB (v2: Macronix MX 25L323F) (v3: Winbond 25Q32FVSIG) - LAN: 4x 100M - WAN: 1x 100M Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
* ar71xx: add support for Rockeetech AP531B0Shuanglin Liu2017-03-121-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB)) - RAM: 64 MiB DDR2 - Storage: 16 MiB of flash (optional 16 MiB second flash) - Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) 1x100M (port 4) - PCI-E: x1 - SIMcard slot: x1 - USB 2.0 port: x1 (optional) - Ext GPIO pin: x8 - UART for serial console: x1 - External watchdog: x1 (optional) - Power supply: 9-48V (DC jack/passive PoE) Installation through tftp: - Copy <Firmware Image Name> into tftp directory - Connect board via ttl port and Ethernet port - Boot the AP531B0 - When "Autobooting in 1 seconds" appears press Enter - Set serverip and ipaddr appropriate (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1) - Enter "tftp 0x8050000 <Firmware Image Name>" - Enter "erase 0x9f050000 +$filesize" - Enter "cp.b 0x80500000 0x9f050000 $filesize" - Enter "reset" Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
* ar71xx: Enable mtdsplit support for RB SPI NOR devicesThibaut VARENE2017-02-221-0/+1
| | | | | | | | | | | | | | | | | | This patch enables mtdsplit for the MikroTik subtarget. It converts mach-rbspi.c to use a single "firmware" partition. Finally, it converts the SPI NOR profile to metadata images: the original combined-image format is gone, the images are now "standard" sysupgrade images with metadata appended. Note: kernel2minor apparently pads the kernel container to erase-block boundary, but this is undocumented behaviour, so we do not rely on it and call pad-to anyway. Note: in platform.sh, the boards are tested last in platform_check_image() as this should eventually become the "*)" default case when more devices switch to metadata images. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for TL-WR802N Version 2Thomas Roberts2017-02-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR802N Version 2. Specification: - SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc) - RAM: 32 MiB - Storage: 4 MiB of FLash on board - Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) Installation through OEM Web Interface: - Connect to TL-WR802N by Ethernet or Wi-Fi - Go to http://192.168.0.1 (default user is "admin" & password is "admin) - Go to "System Tools -> Firmware Upgrade" - Browse for firmware "*.factory-us.bin" or "*.factory-eu.bin" for eu model - Click upgrade Installation through tftp: Note: T_OUT, T_IN and GND on the board must be connected to USB TTL Serial Configuration 115200 8n1 - Boot the TL-WR802N - When "Autobooting in 1 seconds" appears type "tpl" followed by enter - Connect to the board Ethernet port (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10) - tftpboot 0x80000000 <Firmware Image Name> - Record the result of "printenv bootcmd" - Enter "erase <Result of 'printenv bootcmd'> +0x3c0000" (e.g erase 0x9f020000 +0x3c0000) - Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000" (e.g cp.b 0x80000000 0x9f020000 0x3c0000) - Enter "bootm <Result of 'printenv bootcmd'>" (e.g bootm 0x9f020000) Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
* ar71xx: add support for 8devices Lima boardKarol Dudek2017-02-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Lima is a module for the (IoE) internet of everything applications, based on Qualcomm/Atheros QCA4531. Specification: - 650/600/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 32 MB of FLASH - 2T2R 2.4 GHz - 2x 10/100 Mbps Ethernet - USB 2.0 Host - PCIe - UART for serial console - 14x GPIO Flash instruction: 1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin and rename it to 8dev_recovery.bin 2. Binary file copy to USB stick and plug into slot USB 3. Press S2 (reset) button 4. Press and hold the S1 button by 5 seconds 5. Wait ~40 seconds to complete recovery Tested on: - Lima development kit Signed-off-by: Karol Dudek <karoiz@sli.pl>
* ar71xx: provide support for RB-941-2nD via mach-rbspi.cThibaut VARENE2017-02-151-1/+0
| | | | | | | | | This patch implements support for the hAP lite in mach-rbspi.c hAP lite was supported via mach-rb941.c, so this file is removed as well as the corresponding build bits. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB mAP L-2nDThibaut VARENE2017-02-151-0/+1
| | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD mAP lite https://routerboard.com/RBmAPL-2nD Specifications: - SoC: Qualcomm QCA9533 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Wireless: builtin QCA9533, 2x2:2 - Ethernet: 1x100M This is another 16M SPI NOR mikrotik device. The machine file is named mach-rbspi.c because I plan to add support for several of the other spi-based RouterBOARD devices in subsequent patches: they share most of the hardware and thus the same codebase. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for TP-Link TL-WA850RE v2Piotr Dymacz2017-02-141-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/391/195 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x internal antennas (embedded on PCB) - 9x LED (all can be turned off with GPIO15), 2x button - UART (J3) header on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in US version of the device, but should work also with the same device version sold in other countries. Available FLASH space, with LEDE trunk, is only 240 KB. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add kernel support for the OpenMesh A60 boardSven Eckelmann2017-02-141-0/+1
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add support to TP-Link Archer C59v1 and C60v1Henryk Heisig2017-01-261-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: add support for PQI Air PenYuheiOKAWA2017-01-201-0/+1
| | | | | | | | | | | SoC: AR9331 Ethernet x1, Wireless 2.4G, uSD card slot x1. USB Power, include Li-Po Battery. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> Changes in v2: alphabetical ordering, tabs fron spaces.
* ar71xx: add Abicom SC1750 supportConor O'Gorman2017-01-201-0/+1
| | | | | | | | | | | | | | | | Support Abicom International Scorpion SC1750 Board QCA9550 700MHz Extended Temperature Range 256MB DDR2 256MB Nand Flash 16MB Nor Flash 1x SFP, 1x PCIe 2x 10/100/1000 Ethernet 135x100 mm 802.11ng/g/b 802.11ac/an/a Signed-off-by: Conor O'Gorman <i@conorogorman.net>
* ar71xx: add Abicom SC450 supportConor O'Gorman2017-01-201-0/+1
| | | | | | | | | | | | | | | | | | | Support Abicom International Scorpion SC450 Board QCA9550 700MHz Extended Temperature Range 256MB DDR2 256MB NAND Flash 16MB NOR Flash 10/100/1000 Ethernet 15W Max, 3x3 Mode, Full Power TX Power 802.3-at POE+ & DC Input options 100x 85mm USB PCIe SFP GPIO/LED Signed-off-by: Conor O'Gorman <i@conorogorman.net>
* ar71xx: add Abicom SC300M supportConor O'Gorman2017-01-201-0/+1
| | | | | | | | | | | | | | | | | Support Abicom International Scorpion SC300M Module QCA9550 700MHz Extended Temperature Range 256MB DDR2 256MB Nand Flash 16MB SPI Flash 802.11a/na/b/g/ng GPIO x 22, USB x2, PCIe x2 10/100/1000 Ethernet 23dBm, Optional Onboard Antenna DC Input, 8-20V DC 85 x 55 mm Signed-off-by: Conor O'Gorman <i@conorogorman.net>
* ar71xx: add support for RB-941-2nDThibaut VARENE2017-01-161-0/+1
| | | | | | | | | | | | | | | | Add full support for Mikrotik RB-941-2nD (hAP lite) Original patch by Sergey Sergeev <adron@yapic.net> and more information is available here: https://wiki.openwrt.org/toh/mikrotik/rb941_2nd I updated and adapted the patch to apply cleanly to LEDE trunk and added proper numbering for the switch ports (matching case labels). Tested working on actual hardware with the information provided in the above webpage. Sysupgrade works. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for TP-Link RE450Tal Keren2016-12-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | Add full support for TP-Link RE450. The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci). The ethernet interface is AR8035, but the mdio is connected to the gpio and the chipset builtin mdio bus isn't used, which is unique (and weird), so the kernel gpio mdio module is used. The two ethernet leds are connected to the GPIO, so they are both configured, one to indicate link status and the other to indicate data transfer. The generation of the image was added to the image Makefile. The return value of tplink-safeloader is not ignored anymore (to fail on error) The result factory image is flashable from the stock web ui. Signed-off-by: Tal Keren <kooolk@gmail.com> [rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand] Signed-off-by: Radek Dostál <rd@radekdostal.com> [hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard] Signed-off-by: Henryk Heisig <hyniu@o2.pl> [jo@mein.io: squash fixes from Radek and Henryk into original commit] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: add support for TP-LINK WR1043ND v4Ludwig Thomeczek2016-12-201-0/+1
| | | | Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* ar71xx: add support for TP-LINK TL-WR940N v4David Lutz2016-12-161-0/+1
| | | | Signed-off-by: David Lutz <kpanic@hirnduenger.de>
* ar71xx: Added missing support for Linksys E2100LGad Krumholz2016-12-141-0/+1
| | | | | | | | | | | | | It's based on the WRT160NL according to https://wiki.openwrt.org/toh/linksys/e2100l Based on research done here: https://forum.openwrt.org/viewtopic.php?id=24244 and here: https://forum.openwrt.org/viewtopic.php?pid=120791#p120791 this patch was conceived. Signed-off-by: Gad Krumholz <gad.krumholz@gmail.com> [Jo-Philipp Wich: fix ordering, move addpattern change into separate commit] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: remove PB92 reference design board supportFelix Fietkau2016-12-121-1/+0
| | | | | | | Due to flash size limitations, support for this board has not been functional for years Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP113 reference design board supportFelix Fietkau2016-12-121-1/+0
| | | | | | | Due to flash size limitations, support for this board has not been functional for years Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP81 reference design board supportFelix Fietkau2016-12-121-1/+1
| | | | | | This board is very old and unlikely to still be relevant today. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP83 reference design board supportFelix Fietkau2016-12-121-2/+0
| | | | | | | | This board is very old and unlikely to still be relevant today. Support for it contains a significant amount of device specific baggage which is worth getting rid of. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for YunCore SR3200 and XD3200Piotr Dymacz2016-12-121-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore CPE830Piotr Dymacz2016-11-211-0/+1
| | | | | | | | | CPE830 is a clone of AP90Q, with different type of antenna (panel) and additional 4 LEDs for WiFi signal level indication. Use the same flash approach as for YunCore AP90Q. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore CPE870Piotr Dymacz2016-11-211-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341. Short specification: - 535/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm - internal 14 dBi panel antenna - 8x LED, 1x button - UART (JP1) header on PCB Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. setenv bootcmd "bootm 0x9f020000" 5. saveenv && reset Vendor firmware access (login/password): Admin/5up Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore AP90QPiotr Dymacz2016-11-211-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2. Short specification: - 650/600/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz with external PA, up to 29 dBm - 2x internal 5 dBi omni antennas - 4x LED, 1x button - UART (JP1) header on PCB Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Flash instruction under vendor fimrware, using telnet/SSH: 1. Connect PC with 192.168.1.x address to WAN port 2. Power up device, enter failsafe mode with button (no LED indicator!) 3. Change root password and reboot (mount_root, passwd ..., reboot -f) 4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP 5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 6. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9f050000" - mtd erase firmware - mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E380AC v1 and v2Piotr Dymacz2016-11-211-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035. There are two versions of this model, with different RAM and U-Boot mtd partition sizes: - v1: 128 MB of RAM, 128 KB U-Boot image size - v2: 256 MB of RAM, 256 KB U-Boot image size Version number is available only inside vendor GUI, hardware and markings are the same. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 1x 10/100/1000 Mbps Ethernet, with PoE support - 128 or 256 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm - 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm - 6x internal antennas - 1x RGB LED, 1x button - UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB - external watchdog (Pericon Technology PT7A7514) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>