aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/base-files/lib
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: add support for EnGenius ENS202EXTMarty Plummer2017-05-302-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius ENS202EXT is an outdoor wireless access point with 2-port 10/100 switch, detachable antennas and proprietery PoE. The device is based on Qualcomm/Atheros AR9341 v1. Specifications: - 535/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM - 16 MB of FLASH - UART (J1) header on PCB (unpopulated) - 2x 10/100 Mbps Ethernet - 2.4 GHz, up to 26dBm - 2x external, detachable antennas - 7x LED, 1x button Flash instructions: You have three options: - Use the vendor firmware upgrade page on the web interface and give it the factory.img. This is the easiest way to go about it. - If you have serial access during u-boot, interrupt the normal boot (any key before timeout) and run 'run failsafe_boot'; this will bring you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've bricked the normal firmware. - Use the vendor's management cli, which can be accessed via telnet with the same credentials as the web login (default admin:admin), then issue the following commands: *** Hi admin, welcome to use cli(V-1.6.7) *** ---========= Commands Help =========--- stat -- Status sys -- System wless2 -- 2.4G-Wireless mgmt -- Management tree -- Tree help -- Help reboot -- Reboot ens202ext>mgmt Management ---========= Commands Help =========--- admin -- Administration mvlan -- Management VLAN settings snmp -- SNMP settings backup -- Backup/Restore settings autorb -- Auto reboot settings fwgrade -- Firmware upgrade time -- Time settings wifisch -- Wifi schedule log -- Log diag -- Diagnostics disc -- Device Discovery logout -- Logout help -- Help exit -- Exit ens202ext/mgmt>fwgrade Management --> Firmware upgrade ---========= Commands Help =========--- fwup -- Firmware upgrade help -- Help exit -- Exit ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
* ar71xx: fix LED defines for TP-Link TL-WR740N v6Andrey Polischuk2017-05-302-0/+4
| | | | | | Signed-off-by: Andrey Polischuk <androld.b@gmail.com> [changed commit subject, dropped redundant kernel config symbol] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: Add support for TP-Link MR6400Filip Moc2017-05-272-0/+7
| | | | | | | | | | | | | | | | | You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin on 192.168.0.66/24, connect to any ethernet port and power on device while holding the reset button). Flashing via OEM web interface does not work. Hardware Specification (v1.0 EU): - SoC: QCA9531 - Flash: Winbond W25Q64FV (8MiB) - RAM: EtronTech EM6AB160TSE-5G (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 2NIC (3x100M + 1x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 12V 1A Signed-off-by: Filip Moc <lede@moc6.cz>
* Revert "ar71xx: Add support for Teltonika RUT900"John Crispin2017-05-182-5/+1
| | | | | | | | This reverts commit 224e5f5efa22b8a0132522367afd3b22f05d53e1. pepe2k pointed out that this was not ready to merge Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: Add support for Teltonika RUT900Steffen Weinreich2017-05-182-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet ports, I/O, RS232, RS485, GPS. The device ist based on a Atheros AR9344 rev 3, Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM - 16 MB of FLASH - Serial Console header on a Card Board edge connector - 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN) - 2.4 GHz Wifi - 2x external, detachable Wifi antennas - LTE Modem Huawei ME909u-521 (Also other Modem seen) - 2x LTE antennas - 1x GPS antenna - 7x LED, 1x button - 1x USB Connector - 1x Serial RS232 - 1x Serial RS485 - 1x MicroSD Card The GPL sources of the device are available at www.teltonika.lt/gpl/ and are based on OpenWRT Barrier Breaker (14.07) Running from tftp: The Router starts into the uboot Webupdater if the Button ist pressed more than 3 seconds, if no Network cable is attached it starts the uboot serial console, from there the router loads the firmware image via tftpboot from 192.168.1.2:firmware.bin (the router has the 192.168.1.1). With bootm the loaded image will be booted. Signed-off-by: Steffen Weinreich <steve@weinreich.org>
* ar71xx: add support for Aerohive AP-121Chris Blake2017-05-152-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for Aerohive AP-121 access point. Specification: - SoC: Atheros AR9344-BC2A at 560MHz - WiFi 1: 2.4GHz Atheros AR9340? - SoC - WiFi 2: 5.0GHz Atheros AR9382-AL1A - Memory: 128MB from 2x Nanya NT5TU32M16DG-AC - SPI: 1MB Macronix MX25L8006E - NAND: 128MB Hynix H27U1G8F2BTR-BC - Ethernet: Atheros AR8035-A - USB: 1x 2.0 - TPM: Atmel SC3204 Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, download and flash LEDE factory image over tftp: dhcp; setenv serverip tftp-server-ip; tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin; nand erase 0x800000 0x800000; nand write 0x81000000 0x800000 0x800000; reset; Signed-off-by: Chris Blake <chrisrblake93@gmail.com> [minor text changes in commit subject and description, fixed alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh, fixed code style issues in mach-hiveap-121.c, ubinized factory image] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for 8devices Rambutan development boardMantas Pucka2017-05-153-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rambutan is a Wifi module based on QCA9550/9557 http://www.8devices.com/products/rambutan This commit adds basic support for Rambutan development kit Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of DDR2 RAM - 128 MB of NAND Flash - 1x 100Mbps Ethernet - 1x 1000Mbps Ethernet (PHY on dev-kit) - 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz - 2x U.FL connectors on module, chip antennas on dev-kit - 1x miniPCIe slot - 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header Flash instructions: Stock firmware is OpenWrt, so use: sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar or upgarde from GUI (don't save config) Use factory image to flash from U-Boot: tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi nand erase.part ubi nand write 80060000 ubi ${filesize} Signed-off-by: Mantas Pucka <mantas@8devices.com> [split support in uboot-envtools package into a separate commit, fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for UniFi-AC-MeshLudwig Thomeczek2017-05-151-1/+1
| | | | | | | | | | | | | | | | | | | This adds the build option for the new UniFi AC Mesh. It is a direct hardware copy from the AC Lite. - SoC: QCA9563-AL3A (775Mhz) - RAM: 128MiB - Flash: 16MiB - dual firmware partitions! - LAN: 1 1000M - POE - Wireless: 2.4G: QCA9563 5G: UniFi Chip, QCA988X compatible Thanks to Frank Dietz for testing. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net> [wrapped too long lines in mach-ubnt-unifiac.c] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix minor syntax error in /lib/upgrade/platform.shMatthias Schiffer2017-04-221-1/+1
| | | | | | | Fix a '==' that should be a '=' in a test condition. Busybox fortunately doesn't care. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add userspace support for Mikrotik RB2011iLRon Angeles2017-04-032-0/+5
| | | | | | | | | Kernel/hardware support for this board has been implemented since Chaos Calmer. This set of patches is to get the board identified in userland. This will allow support for things like sysupgrade, configuring initial LED state, configuring initial switch state, etc. Signed-off-by: Ron Angeles <ronangeles@gmail.com>
* ar71xx: Compex WPJ563 supportChristian Mehlis2017-03-302-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc) - RAM: 128 MiB - Storage: 16MB NOR flash - Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO - Ethernet: 2x1G Tested and working: - ethernet / switch / lan / wan - 2.4GHz SoC wifi - PCIe - leds - buzzer Ramload: - tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin - bootm 0x84000000 Install: - tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin - erase 0x9f030000 +$filesize - erase 0x9f680000 +1 - cp.b $fileaddr 0x9f030000 $filesize Erasing 0x9f680000 is required because uboot defines "bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot the higher address. I think the 16 mb flash are intended to be used as 8+8mb for a fallback image. In my hardware only the lower address has a bootable image. But to make sure future hardware will boot lede too, I erase one block, so uboot will skip this address. Signed-off-by: Christian Mehlis <christian@m3hlis.de>
* ar71xx: add support for P&W R602N and CPE505NPiotr Dymacz2017-03-232-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-LINK TL-WR840N v2 and v3Vaclav Svoboda2017-03-232-0/+8
| | | | | | | | | | | | | | This patch adds support for the TP-LINK TL-WR840N v2 and v3. - SoC: Qualcomm QCA9533-BL3A (650 MHz) - RAM: 32 MiB (Zentel A3S56D40GTP) - Flash: 4 MiB (v2: Macronix MX 25L323F) (v3: Winbond 25Q32FVSIG) - LAN: 4x 100M - WAN: 1x 100M Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
* ar71xx: add support for MikroTik hAP acRyan Mounce2017-03-232-0/+5
| | | | | | | | | | | This patch adds initial support for the MikroTik RouterBOARD hAP ac (RB962UiGS-5HacT2HnT). All functions are supported except: -SFP cage (eth1) is not working -WLAN LEDs are not working Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ar71xx: add support for MikroTik hAP ac liteRyan Mounce2017-03-232-0/+5
| | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hAP ac lite (RB952Ui-5ac2nD). The hAP ac lite is nearly identical to the hAP, with an added QCA9887 5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ar71xx: add support for RB LHG 5nDThibaut VARENE2017-03-152-0/+5
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD LHG 5 https://routerboard.com/RBLHG-5nD Specifications: - SoC: Atheros AR9344 (600MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Wireless: builtin AR9344 5GHz, 2x2:2 - Ethernet: 1x100M Initial flash via initramfs, like all other RB devices. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: base-files: few minor cleanups in lib/ar71xx.shPiotr Dymacz2017-03-121-39/+16
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: fix boards order in lib/ar71xx.shPiotr Dymacz2017-03-121-276/+276
| | | | | | Keep everything within case statements in alphabetical order. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: shorten case statement patterns in lib/ar71xx.shPiotr Dymacz2017-03-121-13/+13
| | | | | | | | | | | | | | At now there is no general rule about what part of (or whole) machine name string should be used for board name assignment/detection and every target handles this in a different way. For most of the boards in ar71xx we already use only part of the string, generally without the vendor name. This shortens wildcards patterns in case statement for board name assignment, wherever possible (e.g. where it won't be misleading). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: always use double quotes in lib/ar71xx.shPiotr Dymacz2017-03-121-104/+104
| | | | | | | | | | Be consistent and always use double quotes for case statement patterns, as in other targets. With this approach it should be less confusing for users adding support for new devices. Also, be consistent with MikroTik boards wildcard pattern. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: fix indentation in lib/ar71xx.shPiotr Dymacz2017-03-121-19/+19
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Rockeetech AP531B0Shuanglin Liu2017-03-122-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB)) - RAM: 64 MiB DDR2 - Storage: 16 MiB of flash (optional 16 MiB second flash) - Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) 1x100M (port 4) - PCI-E: x1 - SIMcard slot: x1 - USB 2.0 port: x1 (optional) - Ext GPIO pin: x8 - UART for serial console: x1 - External watchdog: x1 (optional) - Power supply: 9-48V (DC jack/passive PoE) Installation through tftp: - Copy <Firmware Image Name> into tftp directory - Connect board via ttl port and Ethernet port - Boot the AP531B0 - When "Autobooting in 1 seconds" appears press Enter - Set serverip and ipaddr appropriate (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1) - Enter "tftp 0x8050000 <Firmware Image Name>" - Enter "erase 0x9f050000 +$filesize" - Enter "cp.b 0x80500000 0x9f050000 $filesize" - Enter "reset" Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
* ar71xx: mikrotik: erase firmware partition on SPI NOR devices in pre_upgrade()Thibaut VARENE2017-02-261-0/+8
| | | | | | | | | | | | On Mikrotik SPI NOR devices, the firmware partition must be erased when flashing from stock firmware, otherwise leftover bits (in particular a kernel signature) can trigger a boot loop. When booted from initramfs (the only way to flash LEDE on these devices), this patch unconditionally erases the firmware partition in the pre_upgrade() stage for all supported SPI NOR devices. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: Enable mtdsplit support for RB SPI NOR devicesThibaut VARENE2017-02-221-13/+8
| | | | | | | | | | | | | | | | | | This patch enables mtdsplit for the MikroTik subtarget. It converts mach-rbspi.c to use a single "firmware" partition. Finally, it converts the SPI NOR profile to metadata images: the original combined-image format is gone, the images are now "standard" sysupgrade images with metadata appended. Note: kernel2minor apparently pads the kernel container to erase-block boundary, but this is undocumented behaviour, so we do not rely on it and call pad-to anyway. Note: in platform.sh, the boards are tested last in platform_check_image() as this should eventually become the "*)" default case when more devices switch to metadata images. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: remove bogus "rb*)" catch-all from platform.shThibaut VARENE2017-02-221-8/+54
| | | | | | This patch replaces a dangerous catch-all with the exhaustive list of devices. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for TL-WR802N Version 2Thomas Roberts2017-02-202-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR802N Version 2. Specification: - SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc) - RAM: 32 MiB - Storage: 4 MiB of FLash on board - Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) Installation through OEM Web Interface: - Connect to TL-WR802N by Ethernet or Wi-Fi - Go to http://192.168.0.1 (default user is "admin" & password is "admin) - Go to "System Tools -> Firmware Upgrade" - Browse for firmware "*.factory-us.bin" or "*.factory-eu.bin" for eu model - Click upgrade Installation through tftp: Note: T_OUT, T_IN and GND on the board must be connected to USB TTL Serial Configuration 115200 8n1 - Boot the TL-WR802N - When "Autobooting in 1 seconds" appears type "tpl" followed by enter - Connect to the board Ethernet port (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10) - tftpboot 0x80000000 <Firmware Image Name> - Record the result of "printenv bootcmd" - Enter "erase <Result of 'printenv bootcmd'> +0x3c0000" (e.g erase 0x9f020000 +0x3c0000) - Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000" (e.g cp.b 0x80000000 0x9f020000 0x3c0000) - Enter "bootm <Result of 'printenv bootcmd'>" (e.g bootm 0x9f020000) Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
* ar71xx: add support for 8devices Lima boardKarol Dudek2017-02-172-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Lima is a module for the (IoE) internet of everything applications, based on Qualcomm/Atheros QCA4531. Specification: - 650/600/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 32 MB of FLASH - 2T2R 2.4 GHz - 2x 10/100 Mbps Ethernet - USB 2.0 Host - PCIe - UART for serial console - 14x GPIO Flash instruction: 1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin and rename it to 8dev_recovery.bin 2. Binary file copy to USB stick and plug into slot USB 3. Press S2 (reset) button 4. Press and hold the S1 button by 5 seconds 5. Wait ~40 seconds to complete recovery Tested on: - Lima development kit Signed-off-by: Karol Dudek <karoiz@sli.pl>
* ar71xx: add support for RB750r2Thibaut VARENE2017-02-152-0/+6
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hEX lite https://routerboard.com/RB750r2 Specifications: - SoC: Qualcomm QCA9531 (850MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Ethernet: 5x100M (1 PoE in) This ethernet router is based on the same platform as the hEX PoE lite (it shares the same board identifier), but has no USB and no PoE out. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB750UPr2Thibaut VARENE2017-02-152-0/+6
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hEX PoE lite https://routerboard.com/RB750UPr2 Specifications: - SoC: Qualcomm QCA9531 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Ethernet: 5x100M (1 PoE in, 1 PoE out) - USB: Type A This ethernet router is based on the same platform as the wireless router hAP. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB951Ui-2nDThibaut VARENE2017-02-152-0/+6
| | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hAP https://routerboard.com/RB951Ui-2nD Specifications: - SoC: Qualcomm QCA9531 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Wireless: builtin QCA9531, 2x2:2 - Ethernet: 5x100M (1 PoE in, 1 PoE out) - USB: Type A Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB mAP L-2nDThibaut VARENE2017-02-152-2/+8
| | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD mAP lite https://routerboard.com/RBmAPL-2nD Specifications: - SoC: Qualcomm QCA9533 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Wireless: builtin QCA9533, 2x2:2 - Ethernet: 1x100M This is another 16M SPI NOR mikrotik device. The machine file is named mach-rbspi.c because I plan to add support for several of the other spi-based RouterBOARD devices in subsequent patches: they share most of the hardware and thus the same codebase. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: Add support for D-Link EBR-2310 Rev. CAlexandru Gagniuc2017-02-142-0/+4
| | | | | | | Add support for the EBR-2310, which is almost identical to the DIR-615 rev E4, without the wifi. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
* ar71xx: add support for TP-Link TL-WA850RE v2Piotr Dymacz2017-02-142-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/391/195 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x internal antennas (embedded on PCB) - 9x LED (all can be turned off with GPIO15), 2x button - UART (J3) header on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in US version of the device, but should work also with the same device version sold in other countries. Available FLASH space, with LEDE trunk, is only 240 KB. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: enable sysupgrade for the OpenMesh A40Sven Eckelmann2017-02-142-0/+3
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add user-space support for the OpenMesh A40Sven Eckelmann2017-02-141-0/+3
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: enable sysupgrade for the OpenMesh A60Sven Eckelmann2017-02-142-1/+8
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add user-space support for the OpenMesh A60Sven Eckelmann2017-02-141-0/+3
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: enable sysupgrade for the OpenMesh OM2Pv4/-HSv4Sven Eckelmann2017-02-142-0/+6
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add user-space support for the OpenMesh OM2Pv4/-HSv4Sven Eckelmann2017-02-141-0/+6
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: fix platform_find_rootfspart()Thibaut VARENE2017-02-121-1/+1
| | | | | | | | platform_find_rootfspart() fails if the kernel partition comes before the rootfs partition. The proposed patch fixes this while preserving what I understand was the original idea: stop at first match. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support to TP-Link Archer C59v1 and C60v1Henryk Heisig2017-01-262-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: improve Mikrotik hAP Lite device supportAlex Samorukov2017-01-251-0/+2
| | | | | | | | - remove CONFIG_MTD_SPI_NOR_USE_4K_SECTORS - enable jffs2 support - fix sysupgrade Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>
* ar71xx: add support for PQI Air PenYuheiOKAWA2017-01-202-0/+4
| | | | | | | | | | | SoC: AR9331 Ethernet x1, Wireless 2.4G, uSD card slot x1. USB Power, include Li-Po Battery. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> Changes in v2: alphabetical ordering, tabs fron spaces.
* ar71xx: add Abicom SC1750 supportConor O'Gorman2017-01-202-0/+4
| | | | | | | | | | | | | | | | Support Abicom International Scorpion SC1750 Board QCA9550 700MHz Extended Temperature Range 256MB DDR2 256MB Nand Flash 16MB Nor Flash 1x SFP, 1x PCIe 2x 10/100/1000 Ethernet 135x100 mm 802.11ng/g/b 802.11ac/an/a Signed-off-by: Conor O'Gorman <i@conorogorman.net>
* ar71xx: add Abicom SC450 supportConor O'Gorman2017-01-202-0/+4
| | | | | | | | | | | | | | | | | | | Support Abicom International Scorpion SC450 Board QCA9550 700MHz Extended Temperature Range 256MB DDR2 256MB NAND Flash 16MB NOR Flash 10/100/1000 Ethernet 15W Max, 3x3 Mode, Full Power TX Power 802.3-at POE+ & DC Input options 100x 85mm USB PCIe SFP GPIO/LED Signed-off-by: Conor O'Gorman <i@conorogorman.net>
* ar71xx: add Abicom SC300M supportConor O'Gorman2017-01-202-0/+4
| | | | | | | | | | | | | | | | | Support Abicom International Scorpion SC300M Module QCA9550 700MHz Extended Temperature Range 256MB DDR2 256MB Nand Flash 16MB SPI Flash 802.11a/na/b/g/ng GPIO x 22, USB x2, PCIe x2 10/100/1000 Ethernet 23dBm, Optional Onboard Antenna DC Input, 8-20V DC 85 x 55 mm Signed-off-by: Conor O'Gorman <i@conorogorman.net>
* ar71xx: add support for RB-941-2nDThibaut VARENE2017-01-162-3/+29
| | | | | | | | | | | | | | | | Add full support for Mikrotik RB-941-2nD (hAP lite) Original patch by Sergey Sergeev <adron@yapic.net> and more information is available here: https://wiki.openwrt.org/toh/mikrotik/rb941_2nd I updated and adapted the patch to apply cleanly to LEDE trunk and added proper numbering for the switch ports (matching case labels). Tested working on actual hardware with the information provided in the above webpage. Sysupgrade works. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: convert mikrotik routerboard support to UBIFelix Fietkau2017-01-161-0/+30
| | | | | | | | | | Remove the wget2nand script, drop the need for manual installation, use sysupgrade instead. There are now two different NAND images, one for 64 MiB flashes, the other for >= 128 MiB Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for TP-Link WBS210/510Matthias Schiffer2017-01-052-1/+11
| | | | | | | The devices are mostly identical to the CPE210/510, but use external antennas. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add support for TP-Link RE450Tal Keren2016-12-222-0/+4
| | | | | | | | | | | | | | | | | | | | | | | Add full support for TP-Link RE450. The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci). The ethernet interface is AR8035, but the mdio is connected to the gpio and the chipset builtin mdio bus isn't used, which is unique (and weird), so the kernel gpio mdio module is used. The two ethernet leds are connected to the GPIO, so they are both configured, one to indicate link status and the other to indicate data transfer. The generation of the image was added to the image Makefile. The return value of tplink-safeloader is not ignored anymore (to fail on error) The result factory image is flashable from the stock web ui. Signed-off-by: Tal Keren <kooolk@gmail.com> [rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand] Signed-off-by: Radek Dostál <rd@radekdostal.com> [hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard] Signed-off-by: Henryk Heisig <hyniu@o2.pl> [jo@mein.io: squash fixes from Radek and Henryk into original commit] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-03 10:01:37 +0000