| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the Airtight C-60.
SOC: Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM: 128 MiB
NOR: MX25L3205D 4MiB
NAND: ST Micro NAND 32MiB 3,3V 8-bit
SW-NET: AR8327N (2 Ports)
WLAN1: Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2: Dual-Band AR9300 Rev:4 PCIe Chip
The switch is setup for an accesspoint:
LAN1: (gigabit) is the wan-port.
LAN2: (fast ethernet) is bridged with the br-lan.
Flashing Guide (via initramfs):
1. Connect a PC to the serial port of the C-60.
power up the C-60.
Enter u-boot command prompt:
#> nand erase
#> setenv bootcmd "bootm 0x9f060000"
#> saveenv
#> setenv ipaddr 192.168.1.1
#> setenv netmask 255.255.255.0
#> setenv serverip 192.168.1.100
#> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
#> tftpboot
#> bootm
2. Wait for the C-60 to boot LEDE.
On the root prompt. Enter:
# ubiformat /dev/mtd4
# ubiattach -p /dev/mtd4
3. After that copy the sysupgrade.tar onto the router and run:
# sysupgrade sysupgrade.tar
to flash the image.
Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ar71xx has an init-script for special devices where the ath10k OTP
calibration data is stored on the PCIe card's EEPROM (and thus can only
be read by ath10k). Unfortunately the OTP data uses the default mac
address (= all devices come with the same mac address, which leads to
problems when you have multiple of these devices in the same network).
To work around this the mac address is patched in the firmware during
the first boot of the device. To prevent flash wear this was only done
if the ath10k firmware matched a hardcoded md5sum.
However, if the md5sum does not match this can mean that either the mac
address was already patched (which is fine) - unfortunately it can also
mean that the firmware version was updated without updating the
hardcoded md5sum.
Change the "was the mac address already patched" check to actually
compare the mac address inside the ath10k firmware.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
|
|
|
|
|
|
|
|
|
| |
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for Netgear WPN824N.
Hardware specs:
* AR7240, 4 LAN ports, 1 WAN port
* AR9285 WLAN
* 32 MB RAM
* 4 MB Flash
* 16 LEDs (LAN, WAN and Power/Status contain two LEDs for dual color
effect)
* 3 Buttons (not supported)
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48356
|
|
|
|
|
|
| |
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47985
|
|
|
|
|
|
|
|
| |
This patch is to add support for the AirTight Networks C-55 Access Point
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47973
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for TRENDnet TEW-823DRU:
- cpu: QCA9558 @720MHz
- flash: 16MB
- ram: 256MB
- 4+1 RJ45 100/1000Mbps
- wifi: QCA9558 (bgn) and QCA9880-BR4A (ac)
- 1x USB 2.0
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 47927
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47420
|
|
|
|
|
|
| |
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46457
|
|
|
|
|
|
|
|
| |
r46248 added case statements in the same places
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 46274
|
|
|
|
|
|
|
|
| |
Based on trunk r46212.
Signed-off-by: Jaehoon You <teslamint@gmail.com>
SVN-Revision: 46248
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.
This patch makes all boards use the first method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46244
|
|
|
|
|
|
|
|
|
| |
Update firmware name and md5sum. MAC-address location remains
unchanged from previous version.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46196
|
|
|
|
|
|
|
|
|
| |
In new firmware-4.bin (for ath10k) mac offset is 0x114 (276), not 0x118 (280).
This also closes #19751, bug introduced in #45624
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 45958
|
|
|
|
|
|
|
|
| |
It has been broken since the new ath10k firmware introduced in r44656.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 45624
|
|
|
|
|
|
|
|
|
|
|
|
| |
The firware md5sum check never worked due to missing dollar signs.
Also suppress
`md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44486
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the mc-mac1200r target to do_load_ath10k_board_bin() in
target/linux/ar71xx/base-files/lib/preinit/81_load_ath10k_board_bin to load the
ath10k radio MAC address from the EEPROM in MERCURY MAC1200R devices
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44375
|
|
|
|
|
|
|
|
|
|
|
| |
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
|
|
|
|
|
|
|
|
|
| |
It moves firmware patch code behind an extra check on board_name.
Otherwise it will calculate firmware checksum for unaffected boards.
It also reduce boottime by a md5 calculation and removes error message
on boot if firmware not found.
SVN-Revision: 43679
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 43401
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 43382
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 42552
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 42130
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 41814
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 41757
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Patch is based on http://patchwork.openwrt.org/patch/5273/.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5652/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41619
|
|
|
|
|
|
|
|
|
|
| |
With help of this script the ath10k board.bin settings are loaded from
flash and saved to the ath10k firmware directory. The driver reads it
later in the boot process.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41562
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The ar71xx platform always uses the eth0 interface to provide
access to the device in failsafe mode. Due to this, failsafe
access is broken on devices where the LAN ports are connected
to the 'eth1' interface.
Update the relevant script to correctly set the ifname variable
for these devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39752
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37000
|
|
|
|
| |
SVN-Revision: 30660
|
|
|
|
| |
SVN-Revision: 29432
|
|
|
|
| |
SVN-Revision: 26603
|
|
|
|
|
|
| |
preinit_main. This fixes a bug in which the vars were not set due to /proc not being mounted when ar71xx.sh was sourced
SVN-Revision: 21634
|
|
|
|
|
|
| |
(thx, cshore)
SVN-Revision: 19370
|
|
SVN-Revision: 19331
|