aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/base-files/etc
Commit message (Collapse)AuthorAgeFilesLines
...
* ar71xx: add support for Mikrotik RB750P-PBr2Robert Marko2017-10-144-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: Qualcomm QCA9531 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Ethernet: 5x100M (1 PoE in, 4 PoE out) - Outdoor use ready This ethernet router is based on the same platform as the hEX PoE lite. Installation 1. login to the Mikrotik WebUI to backup your licence keys 2. setup a DHCP/BOOTP Server with: * DHCP-Option 66 (TFTP server name) pointing to a local TFTP Server within the same subnet of the DHCP range * DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. connect the port labled internet to your local network 4. keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP Server. Login as root/without password to the started LEDE via ssh listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: * rbcfg set boot_protocol bootp * rbcfg set boot_device ethnand * rbcfg apply Open Netinstall and reboot routerboard. Now netinstall sees routerboard and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall Signed-off-by: Robert Marko <robimarko@gmail.com>
* ar71xx: fix MAC addresses on TP-Link TL-WR1043ND v4Matthias Schiffer2017-09-111-1/+2
| | | | | | | | | | The addresses were read from the 'config' partition, which would not always contain the addresses at the same offsets, depending on the stock firmware version used before flashing LEDE. Change this to get the addresses from the 'product-info' partition, which is read-only. Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: wpj558: remove unused eth1 device and fix MAC addressEnrique Giraldo2017-09-101-1/+2
| | | | Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
* ar71xx: add support for COMFAST CF-E355ACEnrique Giraldo2017-09-102-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9531 + QCA9882. Short specification: - 2x 10/100 Mbps Ethernet, with PoE support - 64MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, 802.11b/g/n - 2T2R 5 GHz, 802.11ac/n/a - built-in 4x 3 dBi antennas - output power (max): 500 mW (27 dBm) - 1x RGB LED, 1x button - built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net> [whitespace fixes, ac radio caldata offset fix] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for GL.iNet GL-USB150Piotr Dymacz2017-09-103-0/+3
| | | | | | | | | | | | | | | | | | | | | GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4) - 1T1R 2.4 GHz - 2x LED, 1x button - UART header on PCB Flash instruction: Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used to flash LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: WNDR4300: use the switch LED trigger on the WAN portDaniel Gonzalez Cabanelas2017-09-051-1/+2
| | | | | | | | | | The WAN port on the Netgear WNDR4300 router has two LEDs, amber and green. Use the switch LED trigger to behave as the rest of the LAN HW controlled LEDs - Green: 1 Gbps - Amber: 100/10 Mbps Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* ar71xx: fix switch port numbering on RB750r2 and RB750UPr2João Chaínho2017-08-311-2/+6
| | | | | | | This patch fixes the switch port numbering on Mikrotik RB750r2 (hEX lite) and RB750UPr2 (hEX PoE lite). Tested on a RB750UPr2. Maybe this patch is applicable to other devices (e.g. RB951Ui-2nD, RB952Ui-5ac2nD) but I have no way to test them. Signed-off-by: João Chaínho <joaochainho@gmail.com>
* ar71xx: add support for ALFA Network AP121FPiotr Dymacz2017-07-223-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users. Device is based on Atheros AR9331 WiSoC and is running a custom version (updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR1) - 16 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet - 1T1R 2.4 GHz - 1x microSD (optional, on separate PCB) - 3x LED, 1x button, 1x switch - UART header on PCB Flash instruction (under U-Boot web recovery mode): 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with RJ45 port, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: use the RB912UAG-{2, 5}HPnD Power LED for diagSergey Ryazanov2017-07-201-2/+2
| | | | | | | The Power LED of RB912UAG-{2,5}HPnD boards can be controlled by sofware, so use it for diag purposes and make the User LED free for other tasks. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* treewide: use the generic board_name functionMathias Kresin2017-07-1512-30/+21
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: support LED in TP-Link TL-WR902AC RJ45 socketPiotr Dymacz2017-07-091-1/+1
| | | | | | | | | TP-Link TL-WR902AC has another one, tiny LED inside RJ45 socket which is attached to GPIO15. Add support for it, use it as a "lan" LED and rename old one to "internet". Also, fix uci option name for "lan" LED in system configuration ("wan" -> "lan"). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix Netgear WNDR3700 v4 switch port mappingQian Zheng2017-07-041-2/+2
| | | | Signed-off-by: Qian Zheng <sotux82@gmail.com>
* ar71xx: add support for TP-Link TL-WR902AC v1Piotr Dymacz2017-07-044-2/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of TL-MR3020 (both devices use very similar enclosure, in same size). New device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (GPIO-controlled power) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch - UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper resitors are missing on TX/RX lines) - 1x micro USB (for power only) Flash instructions: Use "factory" image under vendor GUI. Recovery instructions: This device contains tftp recovery mode inside U-Boot. You can use it to flash LEDE (use "factory" image) or vendor firmware. 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin" to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir. 3. Connect PC with LAN port, press the reset button, power up the router and keep button pressed until WPS LED lights up. 4. Router will download file from server, write it to flash and reboot. Root access over serial line in vendor firmware: root/sohoadmin. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix typo in network defaultsJo-Philipp Wich2017-06-291-1/+1
| | | | | | | | Commit 9fec39a (ar71xx: add support for TP-Link TL-WA855RE v1) introduced a typo in 02_network, fix it by removing the stray paren. Reported-by: Henryk Heisig <hyniu@o2.pl> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: fix switch port mapping for TP-Link TL-WR74xN/D seriesPiotr Dymacz2017-06-291-1/+1
| | | | | | Fixes FS#843 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link Archer C58 v1Henryk Heisig2017-06-295-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 6x LED, 3x button - UART header on PCB, RX, TX at TP4+5 (backside) QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to patch macaddress. Flash instruction: Use "factory" image directly in vendor GUI. Recovery method: 1. Set PC to fixed ip address 192.168.0.66/24. 2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and rename it to "tp_recovery.bin". 3. Start a tftp server with the file "tp_recovery.bin" in its root directory. 4. Turn off the router. 5. Press and hold Reset button. 6. Turn on router with the reset button pressed and wait ~15 seconds. 7. Release the reset button and after a short time the firmware should be transferred from the tftp server. 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin erase 0x9f020000 +$filesize cp.b $fileaddr 0x9f020000 $filesize reset This commit is based on GitHub PR#1112 Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for TP-Link TL-WA855RE v1Federico Cappon2017-06-292-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/397/198 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x external antennas - 2x LED (green and orange in the same package), 2x button - UART: TP5(TX) and TP4(RX) test points on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in EU version of the device, but should work also with the same device version sold in other countries. Signed-off-by: Federico Cappon <dududede371@gmail.com>
* ar71xx: wpj344: set MAC on wanLeon M. George2017-06-291-0/+3
| | | | Signed-off-by: Leon M. George <leon@georgemail.eu>
* ar71xx: add AVM FRITZ!WLAN Repeater 300E supportMathias Kresin2017-06-244-0/+36
| | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: AR7242 (Virian 400MHz) * RAM: 64 MB DDR (W9751G6JB-25) * Flash: 16MB SPI flash (S25FL129PIF) * WiFi: AR9382 (2.4/5GHz) + 2x SE2595L * LAN: 1x1000M (PEF7071V) To install LEDE via EVA bootloader, a FTP connection need to be established to 192.168.178.1 within the first seconds after power on: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: base-files: cleanups in 10-ar922x-led-fixPiotr Dymacz2017-06-111-22/+20
| | | | | | | Fix code style, indentation and leading/trailing whitespaces in: /etc/hotplug.d/net/10-ar922x-led-fix Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: cleanups in 11-ath10k-caldataPiotr Dymacz2017-06-111-24/+24
| | | | | | | Fix code style and boards alphabetical order in: /etc/hotplug.d/firmware/11-ath10k-caldata Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link Archer C25 v1Ludwig Thomeczek2017-06-114-0/+12
| | | | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net> [minor code style fixes, boards alphabetical order fixes, reworked commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link TL-WR942N v1Serg Studzinskii2017-06-113-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on Qualcomm/Atheros QCA9561. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x USB 2.0 - 11x LED (most are controlled by 74HC595) - 2x button - UART header on PCB* * Serial console is disabled in OEM non-beta firmwares and corresponding GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by production (non-beta) U-Boot and firmware. Currently not working: 1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs by some U-Boot versions. Flash instruction under vendor GUI: 1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin". 2. Go to WEB interface and perform usual firmware upgrade. FLash instruction under U-Boot recovery mode (doesn't work in beta firmware): 1. Setup PC with static IP "192.168.0.66/24" and tftp server. 2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make it available to download from your tftp server. 3. Press "reset" button and power up the router, wait till "WPS" LED turns on. Flash instruction under U-Boot, using UART (can be done only with preinstalled UART-enabled U-Boot version!): 1. Use "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Serg Studzinskii <serguzhg@gmail.com> [minor code style fixes, extended commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix Wallys DR344 GPIO-connected LEDs and buttonPiotr Dymacz2017-05-302-0/+7
| | | | | | | | | | | | | | | | | | | | This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board and sets color of all LEDs to green as the mass production boards have only green one. Actually, DR344 has 6 GPIO-connected LEDs and one button: - GPIO11: status - GPIO12: sig1 - GPIO13: sig2 - GPIO14: sig3 - GPIO15: sig4 - GPIO16: reset button - GPIO17: lan WAN LED is connected directly with AR8035 PHY. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: set GE interface as wan by default in Wallys DR344Piotr Dymacz2017-05-301-1/+1
| | | | | | | This aligns default network interfaces configuration with vendor firmware: GE (eth0) -> wan, FE (eth1) -> lan. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for EnGenius ENS202EXTMarty Plummer2017-05-302-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius ENS202EXT is an outdoor wireless access point with 2-port 10/100 switch, detachable antennas and proprietery PoE. The device is based on Qualcomm/Atheros AR9341 v1. Specifications: - 535/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM - 16 MB of FLASH - UART (J1) header on PCB (unpopulated) - 2x 10/100 Mbps Ethernet - 2.4 GHz, up to 26dBm - 2x external, detachable antennas - 7x LED, 1x button Flash instructions: You have three options: - Use the vendor firmware upgrade page on the web interface and give it the factory.img. This is the easiest way to go about it. - If you have serial access during u-boot, interrupt the normal boot (any key before timeout) and run 'run failsafe_boot'; this will bring you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've bricked the normal firmware. - Use the vendor's management cli, which can be accessed via telnet with the same credentials as the web login (default admin:admin), then issue the following commands: *** Hi admin, welcome to use cli(V-1.6.7) *** ---========= Commands Help =========--- stat -- Status sys -- System wless2 -- 2.4G-Wireless mgmt -- Management tree -- Tree help -- Help reboot -- Reboot ens202ext>mgmt Management ---========= Commands Help =========--- admin -- Administration mvlan -- Management VLAN settings snmp -- SNMP settings backup -- Backup/Restore settings autorb -- Auto reboot settings fwgrade -- Firmware upgrade time -- Time settings wifisch -- Wifi schedule log -- Log diag -- Diagnostics disc -- Device Discovery logout -- Logout help -- Help exit -- Exit ens202ext/mgmt>fwgrade Management --> Firmware upgrade ---========= Commands Help =========--- fwup -- Firmware upgrade help -- Help exit -- Exit ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
* ar71xx: fix LED defines for TP-Link TL-WR740N v6Andrey Polischuk2017-05-303-16/+19
| | | | | | Signed-off-by: Andrey Polischuk <androld.b@gmail.com> [changed commit subject, dropped redundant kernel config symbol] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: Add support for TP-Link MR6400Filip Moc2017-05-273-0/+14
| | | | | | | | | | | | | | | | | You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin on 192.168.0.66/24, connect to any ethernet port and power on device while holding the reset button). Flashing via OEM web interface does not work. Hardware Specification (v1.0 EU): - SoC: QCA9531 - Flash: Winbond W25Q64FV (8MiB) - RAM: EtronTech EM6AB160TSE-5G (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 2NIC (3x100M + 1x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 12V 1A Signed-off-by: Filip Moc <lede@moc6.cz>
* Revert "ar71xx: Add support for Teltonika RUT900"John Crispin2017-05-181-3/+0
| | | | | | | | This reverts commit 224e5f5efa22b8a0132522367afd3b22f05d53e1. pepe2k pointed out that this was not ready to merge Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: Add support for Teltonika RUT900Steffen Weinreich2017-05-181-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet ports, I/O, RS232, RS485, GPS. The device ist based on a Atheros AR9344 rev 3, Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM - 16 MB of FLASH - Serial Console header on a Card Board edge connector - 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN) - 2.4 GHz Wifi - 2x external, detachable Wifi antennas - LTE Modem Huawei ME909u-521 (Also other Modem seen) - 2x LTE antennas - 1x GPS antenna - 7x LED, 1x button - 1x USB Connector - 1x Serial RS232 - 1x Serial RS485 - 1x MicroSD Card The GPL sources of the device are available at www.teltonika.lt/gpl/ and are based on OpenWRT Barrier Breaker (14.07) Running from tftp: The Router starts into the uboot Webupdater if the Button ist pressed more than 3 seconds, if no Network cable is attached it starts the uboot serial console, from there the router loads the firmware image via tftpboot from 192.168.1.2:firmware.bin (the router has the 192.168.1.1). With bootm the loaded image will be booted. Signed-off-by: Steffen Weinreich <steve@weinreich.org>
* ar71xx: add support for Aerohive AP-121Chris Blake2017-05-152-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for Aerohive AP-121 access point. Specification: - SoC: Atheros AR9344-BC2A at 560MHz - WiFi 1: 2.4GHz Atheros AR9340? - SoC - WiFi 2: 5.0GHz Atheros AR9382-AL1A - Memory: 128MB from 2x Nanya NT5TU32M16DG-AC - SPI: 1MB Macronix MX25L8006E - NAND: 128MB Hynix H27U1G8F2BTR-BC - Ethernet: Atheros AR8035-A - USB: 1x 2.0 - TPM: Atmel SC3204 Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, download and flash LEDE factory image over tftp: dhcp; setenv serverip tftp-server-ip; tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin; nand erase 0x800000 0x800000; nand write 0x81000000 0x800000 0x800000; reset; Signed-off-by: Chris Blake <chrisrblake93@gmail.com> [minor text changes in commit subject and description, fixed alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh, fixed code style issues in mach-hiveap-121.c, ubinized factory image] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for 8devices Rambutan development boardMantas Pucka2017-05-151-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rambutan is a Wifi module based on QCA9550/9557 http://www.8devices.com/products/rambutan This commit adds basic support for Rambutan development kit Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of DDR2 RAM - 128 MB of NAND Flash - 1x 100Mbps Ethernet - 1x 1000Mbps Ethernet (PHY on dev-kit) - 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz - 2x U.FL connectors on module, chip antennas on dev-kit - 1x miniPCIe slot - 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header Flash instructions: Stock firmware is OpenWrt, so use: sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar or upgarde from GUI (don't save config) Use factory image to flash from U-Boot: tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi nand erase.part ubi nand write 80060000 ubi ${filesize} Signed-off-by: Mantas Pucka <mantas@8devices.com> [split support in uboot-envtools package into a separate commit, fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix switch port mapping for ap123 based TP-Link devicesOldřich Jedlička2017-05-151-8/+8
| | | | | | | | | | | | | This fixes switch port mapping for: TL-WR841N/ND v8, TL-MR3420 v2 and TL-WR941N/ND v5. All of them share the same Atheros ap123 reference design. The order of switch ports (shown in "swconfig dev eth1 show") is CPU, LAN 4, LAN 1, LAN 2, LAN 3. Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com> [included 2 more devices] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix ath9k default LED changes falloutMathias Kresin2017-04-131-0/+7
| | | | | | | | | | | | | | | | Since 192f0a3db859 ("ath9k: unset the default LED pin if used by platform leds") the default ath9k wireless LED is not set as soon as any pin of the ath ath9k gpio controller is used. All touched boards have leds defined which are using the gpio pins exposed by the ath9k driver but rely on a default set wireless led trigger. Add the wireless leds were missing and setup the wireless phy trigger in userspace. Signed-off-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: add correct named default wireless led by using platform ledsMathias Kresin2017-04-081-3/+3
| | | | | | | | | | | | | Instead of renaming the default wireless led attached to the wireless chip, add a new led using the platform leds with the phy0tpt trigger set in userspace. When switching ar71xx to device tree, the same can be done by using the build in GPIO controller and without adding new bindings. Drop the now unused platform code. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: add userspace support for Mikrotik RB2011iLRon Angeles2017-04-034-2/+6
| | | | | | | | | Kernel/hardware support for this board has been implemented since Chaos Calmer. This set of patches is to get the board identified in userland. This will allow support for things like sysupgrade, configuring initial LED state, configuring initial switch state, etc. Signed-off-by: Ron Angeles <ronangeles@gmail.com>
* ar71xx: Compex WPJ563 supportChristian Mehlis2017-03-302-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc) - RAM: 128 MiB - Storage: 16MB NOR flash - Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO - Ethernet: 2x1G Tested and working: - ethernet / switch / lan / wan - 2.4GHz SoC wifi - PCIe - leds - buzzer Ramload: - tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin - bootm 0x84000000 Install: - tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin - erase 0x9f030000 +$filesize - erase 0x9f680000 +1 - cp.b $fileaddr 0x9f030000 $filesize Erasing 0x9f680000 is required because uboot defines "bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot the higher address. I think the 16 mb flash are intended to be used as 8+8mb for a fallback image. In my hardware only the lower address has a bootable image. But to make sure future hardware will boot lede too, I erase one block, so uboot will skip this address. Signed-off-by: Christian Mehlis <christian@m3hlis.de>
* ar71xx: add support for P&W R602N and CPE505NPiotr Dymacz2017-03-233-8/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-LINK TL-WR840N v2 and v3Vaclav Svoboda2017-03-233-0/+10
| | | | | | | | | | | | | | This patch adds support for the TP-LINK TL-WR840N v2 and v3. - SoC: Qualcomm QCA9533-BL3A (650 MHz) - RAM: 32 MiB (Zentel A3S56D40GTP) - Flash: 4 MiB (v2: Macronix MX 25L323F) (v3: Winbond 25Q32FVSIG) - LAN: 4x 100M - WAN: 1x 100M Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
* ar71xx: add support for MikroTik hAP acRyan Mounce2017-03-234-1/+7
| | | | | | | | | | | This patch adds initial support for the MikroTik RouterBOARD hAP ac (RB962UiGS-5HacT2HnT). All functions are supported except: -SFP cage (eth1) is not working -WLAN LEDs are not working Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ar71xx: add support for MikroTik hAP ac liteRyan Mounce2017-03-235-2/+9
| | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hAP ac lite (RB952Ui-5ac2nD). The hAP ac lite is nearly identical to the hAP, with an added QCA9887 5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ar71xx: add support for RB LHG 5nDThibaut VARENE2017-03-153-0/+11
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD LHG 5 https://routerboard.com/RBLHG-5nD Specifications: - SoC: Atheros AR9344 (600MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Wireless: builtin AR9344 5GHz, 2x2:2 - Ethernet: 1x100M Initial flash via initramfs, like all other RB devices. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: WNDR4300: Fix network vlan IDsDaniel Gonzalez Cabanelas2017-03-131-3/+3
| | | | | | The Netgear WNDR4300 has the VLAN IDs flipped in LuCi, fix it. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* ar71xx: add support for Rockeetech AP531B0Shuanglin Liu2017-03-122-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB)) - RAM: 64 MiB DDR2 - Storage: 16 MiB of flash (optional 16 MiB second flash) - Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) 1x100M (port 4) - PCI-E: x1 - SIMcard slot: x1 - USB 2.0 port: x1 (optional) - Ext GPIO pin: x8 - UART for serial console: x1 - External watchdog: x1 (optional) - Power supply: 9-48V (DC jack/passive PoE) Installation through tftp: - Copy <Firmware Image Name> into tftp directory - Connect board via ttl port and Ethernet port - Boot the AP531B0 - When "Autobooting in 1 seconds" appears press Enter - Set serverip and ipaddr appropriate (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1) - Enter "tftp 0x8050000 <Firmware Image Name>" - Enter "erase 0x9f050000 +$filesize" - Enter "cp.b 0x80500000 0x9f050000 $filesize" - Enter "reset" Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
* ar71xx: set status led for the gl-* boardsWojciech Jowsa2017-03-062-12/+13
| | | | Signed-off-by: Wojciech Jowsa <w.jowsa@radytek.com>
* ar71xx: fix vlan settings for some boardsWeijie Gao2017-02-201-1/+1
| | | | | | | | | | | For AR71XX devices, GMAC1 always connects port 0 of the built-in switch, as the CPU port. This patch sets correct vlan for some devices with wrong settings: a) mark port 0 as CPU port, tagged b) reverse port order, marking these ports untagged Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ar71xx: add support for TL-WR802N Version 2Thomas Roberts2017-02-203-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR802N Version 2. Specification: - SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc) - RAM: 32 MiB - Storage: 4 MiB of FLash on board - Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) Installation through OEM Web Interface: - Connect to TL-WR802N by Ethernet or Wi-Fi - Go to http://192.168.0.1 (default user is "admin" & password is "admin) - Go to "System Tools -> Firmware Upgrade" - Browse for firmware "*.factory-us.bin" or "*.factory-eu.bin" for eu model - Click upgrade Installation through tftp: Note: T_OUT, T_IN and GND on the board must be connected to USB TTL Serial Configuration 115200 8n1 - Boot the TL-WR802N - When "Autobooting in 1 seconds" appears type "tpl" followed by enter - Connect to the board Ethernet port (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10) - tftpboot 0x80000000 <Firmware Image Name> - Record the result of "printenv bootcmd" - Enter "erase <Result of 'printenv bootcmd'> +0x3c0000" (e.g erase 0x9f020000 +0x3c0000) - Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000" (e.g cp.b 0x80000000 0x9f020000 0x3c0000) - Enter "bootm <Result of 'printenv bootcmd'>" (e.g bootm 0x9f020000) Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
* ar71xx: fix lan ports on archer C59 and C60Henryk Heisig2017-02-172-8/+9
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for RB750r2Thibaut VARENE2017-02-153-0/+3
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hEX lite https://routerboard.com/RB750r2 Specifications: - SoC: Qualcomm QCA9531 (850MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Ethernet: 5x100M (1 PoE in) This ethernet router is based on the same platform as the hEX PoE lite (it shares the same board identifier), but has no USB and no PoE out. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB750UPr2Thibaut VARENE2017-02-154-0/+11
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hEX PoE lite https://routerboard.com/RB750UPr2 Specifications: - SoC: Qualcomm QCA9531 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Ethernet: 5x100M (1 PoE in, 1 PoE out) - USB: Type A This ethernet router is based on the same platform as the wireless router hAP. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-02 06:54:22 +0000