aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/apm821xx/dts
Commit message (Collapse)AuthorAgeFilesLines
* apm821xx: remove gpio-interrupt cruftChristian Lamparter2020-02-291-6/+0
| | | | | | | | | | | This hunk became obsolete the moment when our gpio-button-hotplug learned how to deal with interrupt-supported gpio buttons. The gpio driver never supported interrupt handling, so these properties never served any use (outside of a enhanced ppc4xx-gpio driver that was dropped). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: fix fan control on highest stepChristian Lamparter2019-09-291-1/+1
| | | | | | | | | | This patch removes a typo (extra "0") so that the 'cpu-alert6' step is triggered once the system reaches 85°C. Note: Unless the WNDR4700 is placed in an hot oven, the hardware-monitor will never reach this value. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: fix bogus key-presses on bootChristian Lamparter2019-06-204-0/+7
| | | | | | | | | | | | | | | | | | | | | | | "There are often transient line events when the system is powered up and initialized and it is often necessary for the gpio_chip driver to clear any interrupt flags in hardware before setting up the gpio chip, especially the irqchip portions of it." <http://lists.infradead.org/pipermail/openwrt-devel/2019-June/017630.html> This patch adds a fix for the APM821XX's interrupt controller to clear any bogus pending toggled interrupts that happens on various APM821XX boards on boot. The patch also changes the debouce-interval from the default 5ms debounce interval to 60ms all around. The default setting caused on occasions that the button state became stuck in a pressed state, even though the button was released. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: MX60: convert to interrupt-driven gpio-key driverChristian Lamparter2019-06-021-3/+3
| | | | | | | This patch converts the device to use the gpio-key over gpio-key-polled driver. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: MR24: convert to interrupt-driven gpio-key driverChristian Lamparter2019-06-021-5/+3
| | | | | | | This patch converts the device to use the gpio-key over gpio-key-polled driver. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: WNDAP6X0: convert to interrupt-driven gpio-key driverChristian Lamparter2019-06-021-5/+2
| | | | | | | This patch converts the device to use the gpio-key over gpio-key-polled driver. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: wndr4700: interrupt-driven gpio-keysChristian Lamparter2019-05-311-14/+6
| | | | | | | | | | | | This patch fixes the active_low setting and converts all of the physical keys on the wndr4700 to utilize the interrupt-driven gpio-keys driver over the polled version. The sdcard-insertion hack has been removed since the block-subsystem will now be polling the device instead. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: set mib-poll-interval on emac0 attached ar83xx switchPetr Štetiar2019-05-202-0/+4
| | | | | | | | | | | | | Commit "generic: ar8216: add mib_poll_interval switch attribute" sets mib-poll-interval as disabled by default (was set to 2s), so it makes switch LEDs trigger disfunctional on devices which don't have mib-poll-interval set. So this patch sets mib-poll-interval to 500ms on devices which have ar83xx switch connected to emac0, as the same value was set for built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch"). Signed-off-by: Petr Štetiar <ynezz@true.cz>
* apm821xx: dts overhaulChristian Lamparter2019-01-246-26/+4
| | | | | | | | | | - remove stray #address-cells / #size-cells - fix partition unit-addresses in wd-mybooklive.dts - remove index from MBL's gpio node name Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: dts: Unify naming of gpio-led nodesPetr Štetiar2019-01-245-5/+5
| | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
* apm821xx: dts: Unify naming of gpio-keys nodesPetr Štetiar2019-01-245-5/+5
| | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
* apm821xx: add linux 4.19 apm821xx patchesChristian Lamparter2018-12-271-1/+15
| | | | | | | | | | This patch updates the apm821xx target to use the 4.19 kernel. 4.19 ships with all the crypto4xx driver patches. Furthermore, the DW-DMA fix for the SATA controller has been backported from 4.20 and integrated. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: WNDAP620: remove bad semicolon in dts after #includeChristian Lamparter2018-12-091-1/+1
| | | | | | | | | This patch fixes a build warning triggered by a semicolon in the dts after the #include directive. netgear-wndap620.dts:11:33: warning: extra tokens at end of #include directive Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: move fifo-entry-size property to WNDR4700Christian Lamparter2018-12-092-1/+1
| | | | | | | | | This property (and value) came from Netgear's WNDR4700 stock firmware dts. However, other devices do not set it and the EMAC default is 16, which matches that of the programming notes of the APM82181 spec. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for the Netgear WNDAP620 and WNDAP660Christian Lamparter2018-11-263-0/+293
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WNDAP620 and WNDAP660, they are similar devices, but due to the LAN LED configuration, the switch setup and WIFI configuration each gets a different device target. Hardware Highlights WNDAP620: CPU: AMCC PowerPC APM82181 at 1000 MHz DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF CPU: AMCC PowerPC APM82181 at 1000 MHz FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE) Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Serial: console port with RJ45 Interface (9600-N-8-1) LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs Button: Soft Reset Button Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes Hardware Highlights WNDAP660: CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks DRAM: 256 MB, 2 x 128 MiB DDR2 FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE) Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Serial: console port with RJ45 Interface (9600-N-8-1) LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs Button: Soft Reset Button Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes Flashing requirements: - needs a tftp server at 192.168.1.10/serverip. - special 8P8C(aka RJ45)<->D-SUB9 Console Cable ("Cisco Console Cable"). Note: Both WNDAP6x0 have a MAX3232 transceivers, hence no need for any separate CMOS/TTL level shifters. External Antenna: The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations: = Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description ===== 1. | 1 / High | 0 / Low | Use the internal antennae (default) 2. | 0 / Low | 1 / High | Use the external antennae The external antennaes are only meant for the 2.4 GHz band. One-way Flashing instructions via u-boot: 0. connect the serial cable to the RJ45 Console Port Note: This requires a poper RS232 and not a TTL/USB adaptor. 1. power up the AP and interrupt the u-boot process at 'Hit any key to stop autoboot' 2. setup serverip and ipaddr env settings Enter the following commands into the u-boot shell # setenv ipaddr 192.168.1.1 # setenv serverip 192.168.1.10 3. download the factory.img image to the AP Enter the following commands into the u-boot shell # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img 4. verfiy image integrity Enter the following commands into the u-boot shell # crc32 $fileaddr $filesize If the calculated crc32 checksum does not match, go back to step 3. 5. flash the image Enter the following commands into the u-boot shell # nand erase 0x110000 0x1bd0000 # nand write ${kernel_addr_r} 0x110000 ${filesize} 6. setup uboot environment Enter the following commands into the u-boot shell # setenv bootargs # setenv fileaddr # setenv filesize # setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0' # setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}' # setenv bootcmd 'run owrt_boot' # saveenv 7. boot # run bootcmd Booting initramfs instructions via u-boot: Follow steps 0 - 2 from above. 3. boot initramfs Enter the following commands into the u-boot shell # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin # run addtty # bootm ${kernel_addr_r} Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: MR24: add to uboot-envtoolsChristian Lamparter2018-11-261-1/+24
| | | | | | | | This patch adds the complicated u-boot environment access settings for to the MR24 target. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add disk-activity triggers via DT.Christian Lamparter2018-10-202-0/+2
| | | | | | | | The WNDR4700 and the MBL have a dedicated HDD activity LED. This patch adds the default led triggers to the DTS and removes the entries in 01_leds. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: apm82181.dtsi overhaulChristian Lamparter2018-10-201-135/+139
| | | | | | | | | | | | | | | | | | | - order entries by mmio address where possible - switch to lower-case address values - comment on BSP u-boot behaviour in regards to what it edits and look for - annotate irq lines with the help of interrupt-names - remove deprecated "device_type" properties The pci and network device_type had to stay since they are required by the drivers and u-boot. the cpu and memory device_types will remain as well as they are still part of the DT Spec. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: force WNDR4700 console to 115200n8Christian Lamparter2018-10-201-1/+1
| | | | | | | | | | | | | | | | | | | With the upcoming 4.19 release, the serial console on the Netgear WNDR4700 would no longer work as it is never really set and always relied on the kernel's serial code not to change the baud rate. On the stock firmware, Netgear forced the console setting through a custom CONFIG_CMDLINE in their kernel to 115200. Normally, they should have done it in a different way and just passed the baudrate through a "console=..." kernel parameter via the bootargs in the "/chosen" dt node. But in their default u-boot bootcmd setting, they somehow forgot to add the "run addtty", so there's no easy way to pass the baudrate from u-boot to the kernel. So it has to be forced as otherwise it ends up as 9600 baud. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: set uart compatible to ns16750Christian Lamparter2018-10-201-6/+11
| | | | | | | The APM821XX/PPC460EX datasheet mentions: "Register compatibility with 16750 register set" Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: fix dtc compiler warnings for MX60(W) and MR24's dts filesChristian Lamparter2018-09-292-8/+7
| | | | | | | | | | | | | | | | This patch fixes some of the dtc warnings: MR24: "reg" property in [...]mdio/phy@1 has invalid length (4 bytes) Node [...]button@1 has a unit name, but no reg property Relying on default #address-cells value for [...]phy@1 Relying on default #size-cells value for [...]phy@1 MX60(W): Node [..]nand/all has a reg or ranges property, but no unit name Node [..]button@1 has a unit name, but no reg property Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: replace 'linux, stdout-path' with 'stdout-path'Christian Lamparter2018-09-293-3/+3
| | | | | | | | | | | | | | | This follows a similar upstream patch by Rob Herring: |commit 78e5dfea84dc15d69940831b3981b3014d17222e |Author: Rob Herring <robh@kernel.org> |Date: Wed Feb 28 16:44:06 2018 -0600 | powerpc: dts: replace 'linux,stdout-path' with 'stdout-path' | | 'linux,stdout-path' has been deprecated for some time in favor of | 'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'. | Search and replace all the of occurrences with 'stdout-path'. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: fix some cosmetic glitches in dts filesPaul Wassi2018-08-272-2/+0
| | | | | | | | | | | - fix single spaces hidden by a tab - replace indentation with spaces by tabs - make empty lines empty - drop trailing whitespace - drop unnecessary blank lines Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* apm821xx: clean up gpio-hogsChristian Lamparter2018-07-301-30/+29
| | | | | | | | | | | convert the usb and both sata port power related gpio-hogs to what they really are: fixed-regulators. The ethernet phy-reset gpio-hog is replaced by a proper upstream (4.15+) reset-gpios property in the mdio-node. So this will work eventually. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: unify My Book Live Single + Duo imagesChristian Lamparter2018-07-193-228/+182
| | | | | | | | | | | | | | By takimata: "Come to think of it, an MBL Single board boots up just fine on an MBL Duo image, and the MBL Single board identifies completely identical to the MBL Duo (Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB). I wonder if there is any downside to just using the MBL Duo firmware on a MBL Single. I wonder if the two firmwares could even be unified." <https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/9> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: fix usb-otg on 4.14Christian Lamparter2018-07-161-1/+1
| | | | | | | Starting with 4.14, the "amcc,dwc-otg" needs to be used in order to get the usb-otg to work. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: Force Ethernet PHYID on MX60/MX60WChristian Lamparter2018-04-131-1/+1
| | | | | | | | | | The MX60's uboot disables all the PHYs before starting linux. This causes the PHY/switch detection code to malfunction almost all of the time. To get around this, set a compatible flag to force PHYID. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* apm821xx: increase WNDR4700's dtb+kernel partition to 3.5 MiBChristian Lamparter2018-03-301-17/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch cleans and reworks the WNDR4700 dts to increase the now combined dtb+kernel partition to 3.5 MiB. This has become necessary due to the switch to GCC 7.3 and the ever increasing kernel binary size. The dtb+kernel partition was combined in order to finally fix the problem with out-of-sync device-trees. From now on, the kernel and device-tree will always be updated together. Upgrade Note: Existing installations will have to use the TFTP firmware recovery option in order to install the update. Affected users are advised to make a backup of their existing configuration prior to running sysupgrade: <https://openwrt.org/docs/guide-user/installation/generic.backup#backup_openwrt_configuration> Due to the repartitioning of the NAND, the generated backup should be placed on either the internal HDD, an attached USB-Stick or on another PC (externally). To manually trigger the firmware recovery, the reset button has to be pressed (and hold) during boot. U-boot will enter the "Upgrade Mode" and starts a tftpserver listening on 192.168.1.1 for a tftp client from one of the four LAN/Ethernet ports to connect and upload the new system: (enable tftp binary mode!). openwrt-apm821xx-nand-netgear_wndr4700-squashfs-factory.img Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: convert MR24 to use DT PHY defintionChristian Lamparter2018-01-121-0/+12
| | | | | | Convert the MR24 to use the DT phy probing and at803x PHY driver. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add linux 4.14 apm821xx patchesChristian Lamparter2018-01-121-3/+3
| | | | | | | | | | | This patch updates the apm821xx target to use the 4.14 kernel. 4.14 finally ships with a driver for the WNDR4700's tc654 fan controller. The custom driver is deprecated in favor of the upstream driver and the thermal cooling definitions in the DTS are updated. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: dts: rename devices dts files to include the manufacturerChristian Lamparter2017-12-215-0/+0
| | | | | | | | | | | This patch rename all the DT source files in order to match upstream's "manufacturer-device.dts" format. Please note that the DEVICE_DTB isn't changed. This is because the u-boot of the MyBook Live defines the fdt_file variable to be "apollo3g/apollo3g.dtb". Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add product names to the dt compatible for MerakiChristian Lamparter2017-12-212-2/+2
| | | | | | | | | | Meraki choose to use their product's codename as the main compatible string. Mathias Kresin commented that this is a poor choice as this will confuse the users and devs once the device-tree compatible is used for board-detection and possible the image name. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: dts: append SoC compatible to DTSChristian Lamparter2017-12-214-2/+4
| | | | | | | | | | | | | | | | | | | | | This patch appends the "apm,bluestone" or "amcc,apollo3g" machine compatible string to the current device tree source. Please note that unlike other archs the PPC DT code does not regard the machine's compatible string as a priority list. This is explained in the kernel's usage-model.txt as follows: "PowerPC uses a slightly different scheme where it calls the .probe() hook from each machine_desc, and the first one returning TRUE is used. However, this approach does not take into account the priority of the compatible list, and probably should be avoided for new architecture support." For this reason, the "apm,bluestone" compatible string can't be added to the WNDR4700. As otherwise the target specific pci fix-up code will get ignored and this causes the ath9k WIFI to not get initialized. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: MyBook Live convert to DT PHYChristian Lamparter2017-12-141-0/+11
| | | | | | Changes MyBook Live to use DT PHY probing and the broadcom phy driver. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: convert to dt based diag LED scriptChristian Lamparter2017-12-144-8/+24
| | | | | | | | | | | Please note that users with a Netgear WNDR4700 will need to update the device-tree partition manually. For instructions, please refere to commit 49856a4bb581 ("apm821xx: make it possible to update the dtb partition on the WNDR4700") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: make it possible to update the dtb partition on the WNDR4700Christian Lamparter2016-11-241-1/+0
| | | | | | | | | | | | | | | | | | | | Currently, the device-tree partition is marked as read-only. Hence, userspace tools like mtd can't write into the partition. This however will be necessary in case the DTB needs to be updated. This patch also adds the kernel.dtb image, so the compiled DTB is exported as a file and available in the binary directory along the firmware images. Note: the u-boot does expects the dtb to be a uimage. To update the dtb manually: 1. copy the generated dtb to the router. 2. mtd erase /dev/mtd2 3. mtd write wndr4700.dtb /dev/mtd2 Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: Add support for the Cisco Meraki MX60/MX60WChris Blake2016-11-211-0/+186
| | | | | | | | | | | | | | | | | | | This patch adds support for the Cisco Meraki MX60/MX60W Security Appliance. Flashing information can be found at https://github.com/riptidewave93/LEDE-MX60 Specs are as follows: AppliedMicro APM82181 SoC at 800MHz 1GiB NAND - Samsung K9K8G08U0D 512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC Atheros AR8327-BL1A Gigabit Ethernet Switch 1x USB 2.0 Port More info can be found at https://wiki.openwrt.org/toh/meraki/mx60 Cc: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* apm821xx: consolidate apm821xx device trees filesChristian Lamparter2016-11-126-1472/+990
| | | | | | | | | | | | | This patch moves the common SoC device tree entries from the currently four supported platforms into a common apm82181.dtsi. Furthermore, this patch also changes the GPIO, IRQ and input definitions of the supported platforms to use the defined dt-bindings macros for GPIO_ACTIVE_LOW|HIGH, KEY_WPS|RESTART|*, IRQ_TYPE_* when it's appropriate. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: detect sd-card media changes for the WNDR4700Christian Lamparter2016-09-081-1/+1
| | | | | | | | | The insertion or removal of the sd-card cannot be detected by the hardware itself. This is by design. To workaround this, for the WNDR4700 unload/load the dwc2 module in case the the special SD CARD GPIO line is low/high. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for the Netgear Centria N900 WNDR4700/WNDR4720Christian Lamparter2016-07-221-0/+762
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Netgear Centria N900 WNDR4700/WNDR4720 hardware highlights: CPU: AMCC PowerPC APM82181 Rev. E at 1000 MHz (PLB=166, OPB=83, EBC=83 MHz) Security support, Boot ROM Location NAND wo/ECC 2k page (8 bits) 32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory Board: AMCC APM82181 Evaluation Board, PCIE0/SATA1, 1*USB OTG DRAM: 256 MB (ECC not enabled, 500 Mb/s, 32-bit, CL3) NAND: 128 MiB (SLC, erase size: 128 KiB, page size: 2048, OOB size: 64) ETH: Atheros AR8327N Gigabit Switch (4 x LAN, 1 x WAN) USB: 2 x 3.0 (Renesas uPD720202K8-711-BAA-A, firmware not included) SATA: 1 x SATA-II 3.5" Hard Drive Bay for HDDs (DesignWare SATA). WLAN1: Atheros AR9380 5GHz 802.11an 3:3x3 WLAN2: Atheros AR9581 2.4GHz 802.11bgn 3:3x3 SDCARD: GL827L SD/MMC/MS Flash Card Reader (on internal dwc2 USB 2.0 host) I2C: GMT G781 (i2c-0 @ 0x4d - lm90 compatible temperature sensor) TC654 (i2c-0 @ 0x1b - Dual PWM fan Speed controller) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! INFO: Since this device only has a NAND chip. I opted for going with root.squashfs in a UBI volume. There's no squashfs/jffs2 image. This target produces three images. a. netgear factory image This image can be used to flash the Netgear WNDR4700 via the firmware recovery mechanism and the web admin site. The bootloader can be instructed to do a firmware recovery via the # fw_recovery command. It will start a tftp server and listen on 192.168.1.1 (the ipaddr variable in u-boot) for incoming, binary tftp clients. The firmware recovery mechanism is also started if any of the flash content which contains the kernel, device-tree definitions or the (fake)rootfs fails to verify or load. b. sysupgrade.tar image for sysupgrade An sysupgrade will replace the entire current LEDE installation with a newer version. This does include the kernel and the ubi rootfs partition. The configuration can be carried over automatically as well if desired. simply copy the sysupgrade.tar to a the WNDR4700 running LEDE and run: root@lede:~# sysupgrade sysupgrade.tar and let it reboot. Note: The devicetree flash area is NOT updated. Until the devicetree definition is stable, this can lead to all sorts of hardware detection problems! So make sure, if you experience issues: try the fw_recovery. If you are unsure whenever this affects you: test if you can reproduce your issue with the initramfs method. As it will always have up-to-date device-tree definitions. c. initramfs image for TFTP (for development and testing) To use the initramfs method, follow the following steps: 1) Move the "lede-apm821xx-netgear-WNDR4700-initramfs-kernel.bin" file to to the root directory of your TFTP server. 2) rename it to wndr4700.bin 3) On the WNDR4700 - Hit Enter during u-boot and insert: # tftp 400000 wndr4700.bin; run addtty; bootm 400000 - This will boot the LEDE image. Note: The default tftp server is 192.168.1.7, if you want to change it: # setenv serverip 192.168.8.7; Note2: The default address for the WNDR4700 is 192.168.1.1: # setenv ipaddr 192.168.8.8; Note: Connect you tftp server on the last LAN port (not the WAN) Note: The firmware for the USB 3.0 Host chip is not included anymore. Therefore the two USB 3.0 ports will not work without the uPD7070x-firmware package installed. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for the Western Digital MyBook Live SeriesChristian Lamparter2016-07-223-0/+541
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware Highlights: This patch adds support for Western Digital MyBook Live Series: CPU: AMCC PowerPC UNKNOWN (PVR=12c41c83) at 800 MHz (PLB=200, OPB=100, EBC=100 MHz) 32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory Board: Apollo-3G - APM82181 Board, 1*SATA DRAM: 256 MB (2x NT5TU64M16GG-AC) FLASH: 512 kB (SST 39VF040) Ethernet: 1xRGMII - 1 Gbit - Broadcom PHY BCM54610 WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The MyBook Live Duo additionally features a 1x USB 2.0 host port and can support a second hard-drive. This target produces two images for a target. 1. ext4 image The extracted/raw image can be directly installed on the internal HDD via "dd if=img.ext4 of=/dev/sdX". This can either be done in place with the stock MyBook Live firmware via ssh. Or by removing the HDD and writing the image with a different PC. The the compressed images are useful for sysupgrade. 2. recovery.tar image for TFTP and Serial. extract the recovery.tar to a TFTP server directory. On the MyBook Live (Duo) serial port - Hit Enter during u-boot and insert: # setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1; run net_self Where 192.168.1.254 is your TFTP server. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for the Cisco Meraki MR24Chris Blake2016-07-221-0/+433
This patch adds support for the Cisco Meraki MR24 Access point to the apm821xx target. Board: MR24 - Meraki MR24 Cloud Managed Access Point CPU: APM82181 SoC 800 MHz (PLB=200 OPB=100 EBC=100) Flash size: 32MiB RAM Size: 128MiB Wireless: Atheros AR9380 5.0GHz + Atheros AR9380 2.4GHz Ethernet ports: 1x Gigabit Atheros AR8035 WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! For flashing instructions, visit: <https://github.com/riptidewave93/Openwrt-MR24/blob/master/README.md#flashing> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>