| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
By takimata:
"Come to think of it, an MBL Single board boots up just fine on an
MBL Duo image, and the MBL Single board identifies completely
identical to the MBL Duo
(Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB).
I wonder if there is any downside to just using the MBL Duo firmware
on a MBL Single. I wonder if the two firmwares could even be unified."
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/9>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
| |
Changes MyBook Live to use DT PHY probing and the broadcom phy driver.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Please note that users with a Netgear WNDR4700
will need to update the device-tree partition
manually.
For instructions, please refere to commit 49856a4bb581
("apm821xx: make it possible to update the dtb partition on the WNDR4700")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This patch moves the common SoC device tree entries
from the currently four supported platforms into a
common apm82181.dtsi.
Furthermore, this patch also changes the GPIO, IRQ and
input definitions of the supported platforms to use the
defined dt-bindings macros for GPIO_ACTIVE_LOW|HIGH,
KEY_WPS|RESTART|*, IRQ_TYPE_* when it's appropriate.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
Hardware Highlights:
This patch adds support for Western Digital MyBook Live Series:
CPU: AMCC PowerPC UNKNOWN (PVR=12c41c83) at 800 MHz (PLB=200, OPB=100, EBC=100 MHz)
32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory
Board: Apollo-3G - APM82181 Board, 1*SATA
DRAM: 256 MB (2x NT5TU64M16GG-AC)
FLASH: 512 kB (SST 39VF040)
Ethernet: 1xRGMII - 1 Gbit - Broadcom PHY BCM54610
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The MyBook Live Duo additionally features a 1x USB 2.0 host port
and can support a second hard-drive.
This target produces two images for a target.
1. ext4 image
The extracted/raw image can be directly installed on
the internal HDD via "dd if=img.ext4 of=/dev/sdX".
This can either be done in place with the stock MyBook Live
firmware via ssh. Or by removing the HDD and writing the image
with a different PC.
The the compressed images are useful for sysupgrade.
2. recovery.tar image for TFTP and Serial.
extract the recovery.tar to a TFTP server directory.
On the MyBook Live (Duo) serial port - Hit Enter during u-boot and insert:
# setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1; run net_self
Where 192.168.1.254 is your TFTP server.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
