| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Hardware
--------
CPU: Mediatek MT7621
RAM: 256M DDR3
FLASH: 128M NAND
ETH: 1x Gigabit Ethernet
WiFi: Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC)
BTN: 1x Reset (NWA50AX only)
LED: 1x Multi-Color (NWA50AX only)
UART Console
------------
NWA50AX:
Available below the rubber cover next to the ethernet port.
NWA55AXE:
Available on the board when disassembling the device.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
If the currently installed image is started from Slot A, the device will
flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case
and the device will return to the ZyXEL firmware upon next boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP
-----------------
This installation routine is especially useful in case
* unknown device password (NWA55AXE lacks reset button)
* bricked device
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to owrt.bin
$ atnf owrt.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd10 get-status
$ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd10 set-active-image 0
Copy the OpenWrt ramboot-factory image to the device using scp.
Write the factory image to NAND and reboot the device.
$ mtd write ramboot-factory.bin firmware
$ reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a0b7fef0ffe4cd9cca39a652a37e4f3ce8f0a681)
|
|
|
|
|
|
|
|
|
| |
Openwrt now supports only glibc and musl. Add support for musl and
rework the libc check to handle the new config flags and correctly
compile package basend on that.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 7be01fe13b4517e5edb8a4818f437d60144cdcb4)
|
|
|
|
|
|
|
|
| |
Openwrt generate info.mk that contains the libc type. For probe_cc check
if the file exist and parse directly it for LIBC type.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 75311977f5ff64b491cb57ac713d75e0e410d786)
|
|
|
|
|
|
|
|
|
| |
Currently we never call probe_cc before config generation, this cause
the script to never actually detect the correct libc type.
Call probe_cc before config generation to correctl set the .config file.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ddeabc75ebe3151ff7da302cb1aae702b3ad7eba)
|
|
|
|
|
|
|
|
|
| |
It can be useful to overwrite an already generated config.
Option are simply added at the end of the config and make defconfig
will overwrite the relevant option with the new one.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f4dd18ca39c42a324e34633c8ee553717531bc3b)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The parsed prefix in print_config is wrong and this produce broken
generated .config that won't work with any external toolchain.
Currently the prefix from a CC of
'arm-openwrt-linux-muslgnueabi-gcc-12.1.0'
produce a prefix
'arm-openwrt-linux-muslgnueabi-gcc-'
This is wrong as the real prefix should be
'arm-openwrt-linux-muslgnueabi-'
This is probably caused by a change in how the toolchain is now handled
that now append also the gcc version. Probably in ancient days the
version wasn't part of the name and the prefix generation stripped the
'-gcc' instead of the gcc version.
Fix this and correctly strip the gcc version and the gcc suffix to
correctly call toolchain bins.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 53c293262fce844c8291ab82e6726a8489d3c57b)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Several users of wget for downloads (curl is not available in the
system) have reported broken download functionality:
wget --tries=5 --timeout=20 --output-document=- https://cdn.kernel.org/pub/linux/kernel/v5.x/linux-5.10.142.tar.xz
http://: Invalid host name.
Thats all happening due to '' was passed as an argument, which got later
expanded to http://.
In the context of a list constructor '' is not nothing, it is an empty
string element. So fix it by using () as it will yield "nothing" and
thus not introduce an empty string element.
Fixes: #10692
Fixes: 90c6e3aedf16 ("scripts: always check certificates")
Signed-off-by: Jo-Philipp Wich <jo@mein.io> [shellwords() -> ()]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 50a48faa1b8424e6b4b436b7118fffa2cba14b18)
|
|
|
|
|
|
|
|
|
|
|
|
| |
When running build in verbose mode `make V=s` we can see a lot of
following warnings when curl is not available in the system:
Can't exec "curl": No such file or directory at scripts/download.pl line 77.
So lets fix it by redirecting of the stderr to null hole.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c836ca84e8f641e10a8349a8f9b7432b33d6cec1)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remove flags from wget and curl instructing them to ignore bad server
certificates. Although other mechanisms can protect against malicious
modifications of downloads, other vectors of attack may be available
to an adversary.
TLS certificate verification can be disabled by turning oof the
"Enable TLS certificate verification during package download" option
enabled by default in the "Global build settings" in "make menuconfig"
Signed-off-by: Josh Roys <roysjosh@gmail.com>
[ add additional info on how to disable this option ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 90c6e3aedf167b0ae1baf376e7800a631681e69a)
|
|
|
|
|
|
|
|
|
|
|
|
| |
So it can serve as a standalone drop in replacement for xxd utility used
currently mostly in U-Boot packages with `xxd -i` mode which outputs C
include file style, with aim for byte to byte identical output, so the
eventual difference in the generated output is easily spottable.
Fixes: #10555
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jo-Philipp Wich <jo@mein.io> [perl-fu]
(cherry picked from commit 06e01e817ec6643a35beb9e6946689e9cc7d020a)
|
|
|
|
|
|
|
|
| |
In order to make it more portable.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8b278a76d90e3724815a5fde32be59f7796be1d8)
|
|
|
|
|
|
|
|
|
|
| |
xxdi.pl is a Perl script that implements vim's 'xxd -i' mode so that
packages do not have to use all of vim just to get this functionality.
References: #10555
Source: https://github.com/gregkh/xxdi/blob/97a6bd5cee05d1b15851981ec38ef5a460ddfcb1/xxdi.pl
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 2117d04a3aaad3394c0afec799d9c43f8a09c2cf)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Netgear encrypted image is used in various devices including WAX202,
WAX206, and EX6400v3. This image format also requires a dummy squashfs4
image which is added here as well.
References in WAX202 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar
* openwrt/bootloader/u-boot-mt7621-2018.09-gitb178829-20200526/board/ralink/common/dual_image.c
Bootloader code that verifies the presence of a squashfs4 image, thus
a dummy image is added here.
* openwrt/tools/imgencoder/src/gj_enc.c
Contains code that generates the encrypted image. There is support for
adding an RSA signature, but it does not look like the signature is
verified by the stock firmware or bootloader.
* openwrt/tools/imgencoder/src/imagekey.h
Contains the encryption key and IV. It appears the same key/IV is used
for other Netgear devices including WAX206 and EX6400v3.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit efca76ffce5cf464e82d8269d79877f442209a0a)
|
|
|
|
|
|
|
|
|
|
|
|
| |
What should have been only cosmetic changes, ended up in breaking the
script. Rename UIMAGE_CRC_SLICE back to (the original) UIMAGE_CRC_OFF.
Fixes issue #10204 "cameo-tag.py broken"
Reported-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Fixes: f9e840b65700 ("scripts: add CAMEO tag generator")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit ebfe66e494e57f4b421f1190d6bff1d361db1b3d)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This script inserts CAMEO tags into an uImage to make U-Boot
of DGS-1210 switches happy.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Suggested-by: Sander Vanheule <sander@svanheule.net> # Mutual checksum algorithm
[commit title prefix, trailing whitespace, OpenWrt capitalisation, move
CRC calculation comment, use UIMAGE_NAME_*, remove parentheses for
return, use f-string instead of str()]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit f9e840b65700e1cdff6d066d39c163bac936d046)
|
|
|
|
|
|
|
|
|
|
|
| |
The cameo header is a 0x40-byte header used by D-Link DGS 1210 switches
and Apresia ApresiaLightGS series. cameo-imghdr.py is a clean-room
reimplementation of imghdr present in the DGS-1210-28-GPL package.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[fix board_version argument's help text]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 2fd66e058b0804b9c561d8d6858363fdf5bd7aea)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
mtools recursive copy (mcopy -s ...) is using READDIR(3) to iterate
over the directory entries, hence they end up in the FAT filesystem in
traversal order which breaks reproducibility (rather than being added
to the FAT filesystem in a reproducible order). Implement recursive
copy in gen_image_generic.sh in Shell code instead, as in that way we
can force files to be copied in reproducible order.
Fixes: aece8f5ae8 ("scripts/gen_image_generic.sh: generate reproducible EFI filesystem")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4d289ae7e63893f90957b77962c6b60574d35441)
|
|
|
|
|
|
|
|
|
|
| |
Generate FAT filesystem for EFI boot in a reproducible way:
* use '--invariant' option of mkfs.fat
* set timestamps of all files to SOURCE_DATE_EPOCH
* make sure files are ordered locale-independent
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit aece8f5ae8d15e5e79b8e34a176895209709afb6)
|
|
|
|
|
|
|
|
| |
Set fixed timestamp for kernel other files in /boot filesystem.
This should help making x86 *combined* images reproducible.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 068ea2cde04e2666fb05731cea941bccfaeddc25)
|
|
|
|
|
|
|
|
|
| |
Set LC_ALL=C environment variable when calling 'sort' as the sort
order otherwise depends on the locale set.
Fixes: 56ce110b73 ("scripts: make sure conffiles are sorted")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1d77dca3b32dd883bcc2213675cf21111ac1beca)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Introduce `sha256_unsigned` which is a checksum of the image _before_ a
signature is attached. This is helpful to compare image reproducibility.
Since the `.sha256sum` file is located in the $(KDIR) folder, switch
$(BIN_DIR) with $(KDIR) to simplify the code. The value of $(BIN_DIR)
itself is not stored inside the resulting JSON file, so it can be
replaced.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 8822a8d850ba2df69b81289758959bb90643a696)
|
|
|
|
|
|
|
|
|
|
| |
It may happen that conffiles are in different order on different builds.
Make sure they have the same order by sorting them.
FIX: #9612
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 56ce110b73970bcd65d309440baada84c8e1504b)
|
|
|
|
|
|
|
|
| |
Cosmetical change to improve style in mkits.sh.
Fixes: fd679086473 ("scripts: mkits.sh: Allow legacy @ mode for dts creation")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit e89c85249e311e9a376d07cda33c9dc39b12a906)
|
|
|
|
|
|
|
|
|
|
|
|
| |
While at it, also fix the download.xs4all.nl and add ftp.gnu.org to the GNU
mirrors, as it seems to be updated faster.
Deleted (upstreamed):
600-Close_the_file_descriptor.patch [1]
[1] https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=5a98fb7513b559e20dfebdbaa2a471afda3b4742
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
be64enc, be16dec, and be32dec are declared on FreeBSD 13.0, in
/usr/include/sys/endian.h so we should not declare them.
Fixes the following error during feeds update:
staging_dir/host/bin/mkhash: No such file or directory
gcc scripts/mkhash.c
scripts/mkhash.c:111:1: error: redefinition of 'be64enc'
111 | be64enc(void *buf, uint64_t u)
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
It seems, that there are currently some unhandled corner cases in which
`.toolchain_build_ver` results in empty file and thus forcing rebuilds,
even if the toolchain was build correctly just a few moments ago. Until
proper fix is found, workaround that by checking for this corner case
and simply populate `.toolchain_build_ver` file.
While at it, improve the UX and display version mismatch, so it's more
clear what has forced the rebuild:
"Toolchain build version changed (11.2.0-1 != ), running make targetclean"
References: https://gitlab.com/ynezz/openwrt/-/jobs/2133332533/raw
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
|
| |
Fixes following complaints and suggestions:
In scripts/check-toolchain-clean.sh line 2:
eval `grep CONFIG_GCC_VERSION .config`
^-- SC2046 (warning): Quote this to prevent word splitting.
^-- SC2006 (style): Use $(...) notation instead of legacy backticks `...`.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
| |
diffconfig.sh runs ./scripts/config/conf, but it does not get built
with 'make {menu,x,n}config. Call 'make ./scripts/config/conf' to
ensure it's been built before running it, aborting in case of failure.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>[removed Fixes: due revert]
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit c0849c1d9c17ba96a37b67363b5551c065e9f50d as it seems
to introduce regression in config.buildinfo files produced at least by
buildbots:
$ curl -s https://downloads.openwrt.org/snapshots/targets/ath79/generic/config.buildinfo | head -2
make[3]: Entering directory '/builder/shared-workdir/build'
make[3]: Leaving directory '/builder/shared-workdir/build'
References: https://github.com/openwrt/openwrt/issues/9297#issuecomment-1049719381
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
| |
diffconfig.sh runs ./scripts/config/conf, but it does not get built
with 'make {menu,x,n}config. Call 'make ./scripts/config/conf' to
ensure it's been built befpre running it.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Functional Changes
---------- -------
- make 'imply' not impose any restrictions: allow symbols implied by y
to become m
- change "modules" from sub-option to first-level attribute
Bugfixes
--------
- nconf: fix core dump when searching in empty menu
- nconf: stop endless search loops
- xconfig: fix content of the main widget
- xconfig: fix support for the split view mode
Other Changes
----- -------
- highlight xconfig 'comment' lines with '***'
- xconfig: navigate menus on hyperlinks
- xconfig: drop support for Qt4
- improve host ncurses detection
Update the 'option modules' usage to just 'modules' in Config.in.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Both $(AUTORELEASE) and $(PKG_SRC_VERSION) (from luci.git) use the Git
log to determine releases and package timestamps.
Feeds are shallow cloned by default, resulting in an incomplete Git log
and therefore different local package versions than offered upstream.
This commits sets the default feeds to use `src-git-full` to solve that.
Add fixes from "2b1d92f: scripts/feeds: silence git warning by selecting
pull style" to `src-git-full`
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
| |
The value is retreived from a env variable which defaults to be read as
a string. However the SOURCE_DATE_EPOCH is a unix timestamp aka integer.
Fix this to allow downstream tools to parse the value directly.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
Add similar code to what is done on packages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Ubuntu started to flag which as deprecated and it
seems which is not really standard and may vary
across Distro.
Drop the use of which and use the standard 'command -v'
for this simple task.
Which is still present in the prereq if some package/script
still use which.
A utility script called command_all.sh is implemented that
will just mimic the output of which -a.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commits adds the ability to print Kernel versions of all
targets/subtargets. If a testing Kernel is set print that version as
well.
Example output:
apm821xx/nand 5.10
apm821xx/sata 5.10
arc770/generic 5.4
archs38/generic 5.4
armvirt/32 5.10
armvirt/64 5.10
at91/sam9x 5.10
at91/sama5 5.10
ath25/generic 5.4
ath79/generic 5.4 5.10
ath79/mikrotik 5.4 5.10
--- %< ---
This should help to get a quick update on the state of Kernels.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Adds generic support for sysupgrading on eMMC-based devices.
Provide function emmc_do_upgrade and emmc_copy_config to be used in
/lib/upgrade/platform.sh instead of redundantly implementing the same
logic over and over again.
Similar to generic sysupgrade on NAND, use environment variables
CI_KERNPART, CI_ROOTPART and newly introduce CI_DATAPART to indicate
GPT partition names to be used. On devices with more than one MMC
block device, CI_ROOTDEV can be used to specify the MMC device for
partition name lookups.
Also allow to select block devices directly using EMMC_KERN_DEV,
EMMC_ROOT_DEV and EMMC_DATA_DEV, as using GPT partition names is not
always an option (e.g. when forced to use MBR).
To easily handle writing kernel and rootfs make use of sysupgrade.tar
format convention which is also already used for generic NAND support.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
CC: TruongSinh Tran-Nguyen <i@truongsinh.pro>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently ubinize-image script always expects the
rootfs image to be passed and a volume for it created.
So, to allow only ubinizing a kernel for example which
the MikroTik hAP ac3 and other new NAND devices from
MikroTik require make rootfs an optional parameter like
kernel.
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
|
|
|
|
|
|
|
| |
This can be used to ensure that the compiled code is up to date, when
something important changes in the toolchain.
A recent example of this is the gcc 11 fix for a code miscompilation issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
| |
Since version 2.28, git has a config option init.defaultBranch to set the name
of the first branch created with git init. The env script expects this name to
be "master". This commit sets the initial branch name to "master"
instead of using the git configured one.
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
|
|
|
|
|
|
|
|
|
| |
This only affects typos in comments or user-facing output.
Signed-off-by: Josh Soref <jsoref@users.noreply.github.com>
[only picks changes to scripts, drop "commandline" replacement,
fix case for "arbitrary", improve commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
concludes:
commit e7bc8984d9ca ("scripts: make eva_ramboot.py offset configurable")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some packages may require additional group membership for the system
user added by that package. Allow defining additional groups as third
member of the ':'-separated tuple, allowing to specify multiple
','-separated groups with optional GID.
Example:
USERID:=foouser=1000:foogroup=1000:addg1=1001,addg2=1002,addg3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
| |
This reverts commit 7630001427fa266fa61da0b2533e2c1054eababe
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
| |
Update to newly released version 5.14
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
| |
Fixes packaging of eBPF modules
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
| |
The new `pkgmanifestjson` call prints all package manifest of a feed in
JSON format. This function can be used to print an overview of packages
information used for downstream tooling.
The script is entirely based on Petrs work on dependency visualisation.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
| |
The maintainer could be usable for downstream tooling, so start storing
it in the metadata.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
commit 5ec60cbe9d94 ("scripts: mkits.sh: replace @ with - in nodes")
broke support for Meraki MR32 and this patch makes the replacement
configurable allowing for specifying the @ or - or whatever character
that is desired to retain backwards compatibility with existing devices.
For example, this patch includes the fix for the Meraki MR32 in
target/linux/bcm53xx/image for meraki_mr32:
DEVICE_DTS_DELIMITER := @
DEVICE_DTS_CONFIG := config@1
Fixes: 5ec60cbe9d94 ("scripts: mkits.sh: replace @ with - in nodes")
Signed-off-by: Damien Mascord <tusker@tusker.org>
[Added tags, checkpatch.pl fixes, noted that this is for old stuff]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|