aboutsummaryrefslogtreecommitdiffstats
path: root/package
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: add Edgecore ECW5410 supportRobert Marko2020-09-173-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Edgecore ECW5410 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15 - RAM: 256MB(225 usable) DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB S34MS01G2 Parallel NAND - Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn) - CC2540 BLE - UART console on RJ45 next to ethernet ports exposed. Its Cisco pin compatible, 115200 8n1 baud. Installation instructions: Through stock firmware or initramfs. 1.Connect to console 2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe. 3. Transfer factory image 4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path> This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0 Note Initramfs: 1. Connect to console 2. Transfer the image from TFTP server with tftpboot, or by using DHCP advertised image with dhcp command. 3. bootm 4. Run ubiformat /dev/mtd1 You need to interrupt the bootloader after rebooting and run: run altbootcmd This will switch your active rootfs partition to one you wrote to and boot from it. So if rootfs1 is active, then it will change it to rootfs2. This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0 If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those. This will result in wrong ordering and OpenWrt will panic on boot. 5. Transfer sysupgrade image 6. Flash with sysupgrade -n. Note that sysupgrade will write the image to rootfs partition that is not currently in use. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* firmware: ipq-wifi: enable use on IPQ806xRobert Marko2020-09-171-1/+1
| | | | | | | | | This enables the ipq-wifi package to be used on IPQ806x target. Its needed for boards using a different BDF than one shipped in the upstream board-2.bin. Currently needed for Edgecore ECW5410. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* mac80211: allow bigger A-MSDU sizes in VHT, even if HT is limitedFelix Fietkau2020-09-161-0/+26
| | | | | | Improves tx throughput when connecting to some APs (e.g. Asus RT-AC88U) Signed-off-by: Felix Fietkau <nbd@nbd.name>
* base-files: drop default setup for vconfigAdrian Schmutzler2020-09-162-2/+1
| | | | | | | | | | | | | | | | | vconfig has been disabled by default since 2015 [1] and there are no remaining uses in entire OpenWrt trunk. However, we still set up a specific name_type for it during boot. While this setup is properly implemented to be only triggered when vconfig is present, it still seems anachronistic and unnecessary to set up a standard for a tool that is not used anymore. Therefore, this removes the set_name_type initialization and leaves it for those people actually using the tool to configure it as needed. [1] 899a23227e55 ("busybox: improve applets & deprecate ifconfig, route") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* uhttpd: update to the latest masterRafał Miłecki2020-09-151-3/+3
| | | | | | | | 1172357 ubus: add new RESTful API fe1888f ubus: fix blob_buf initialization Fixes: 3d167ed805a9 ("uhttpd: update to the latest master") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* cns3xxx: drop targetAdrian Schmutzler2020-09-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This target has not been updated to 5.4 yet, and the only person trying it (Koen) decided to retreat based on the following reasons: - The target is not DT-aware at all - The huge amount of effort required - The SoC itself reached EoL at Cavium for some time now - Upstream removed some important parts as it's also slowly getting EoL over there - The commercial product that used this will fade out shortly - The amount of download for this binary suggest that the target is not that popular Since nobody has picked up the work since then, and this is the last remaining 4.19-only target, finally drop it now. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* uboot-envtools: mvebu: update uci defaults for Turris OmniaKlaus Kudielka2020-09-132-2/+6
| | | | | | | | | | | | On the Turris Omnia 2019, u-boot environment is located at 0xF0000, instead of 0xC0000. The switch happened with u-boot-omnia package version 2019-04-2 (May 10, 2019). Check the installed u-boot release, and set the default accordingly. Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com> [bump PKG_RELEASE, use lower case for hex offset] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* netifd: update to latest git HEADHans Dedecker2020-09-121-3/+3
| | | | | | | | | 55a7b6b netifd: vxlan: add aging and maxaddress options 11223f5 netifd: vxlan: add most missing boolean options 226566b netifd: vxlan: refactor mapping of boolean attrs a3c033e netifd: vxlan: handle srcport range Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: fix partitions and boot for RAVPower RP-WD03Adrian Schmutzler2020-09-112-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RAVPower RP-WD03 is a battery powered router, with an Ethernet and USB port. Due due a limitation in the vendor supplied U-Boot bootloader, we cannot exceed a 1.5 MB kernel size, as is the case with recent builds (i.e. post v19.07). This breaks both factory and sysupgrade images. To address this, use the lzma loader (loader-okli) to work around this limitation. The improvements here also address the "misplaced" U-Boot environment partition, which is located between the kernel and rootfs in the stock image / implementation. This is addressed by making use of mtd-concat, maximizing space available in the booted image. This will make sysupgrade from earlier versions impossible. Changes are based on the recently supported HooToo HT-TM05, as the hardware is almost identical (except for RAM size) and is from the same vendor (SunValley). While at it, also change the SPI frequency accordingly. Installation: - Download the needed OpenWrt install files, place them in the root of a clean TFTP server running on your computer. Rename the files as, - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs - Plug the router into your computer via Ethernet - Set your computer to use 10.10.10.254 as its IP address - With your router shut down, hold down the power button until the first white LED lights up. - Push and hold the reset button and release the power button. Continue holding the reset button for 30 seconds or until it begins searching for files on your TFTP server, whichever comes first. - The router (10.10.10.128) will look for your computer at 10.10.10.254 and install the two files. Once it has finished installation, it will automatically reboot and start up OpenWrt. - Set your computer to use DHCP for its IP address Notes: - U-Boot environment can be modified, u-boot-env is preserved on initial install or sysupgrade - mtd-concat functionality is included, to leave a "hole" for u-boot-env, combining the OEM kernel and rootfs partitions Most of the changes in this commit are the work of Russell Morris (as credited below), I only wrapped them up and added compat-version. Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader to work! Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03") Suggested-by: Russell Morris <rmorris@rkmorris.us> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* hostapd: add support for per-BSS airtime configurationDavid Bauer2020-09-113-4/+14
| | | | | | | | | | | | Add support for per-BSS airtime weight configuration. This allows to set a airtime weight per BSS as well as a ratio limit based on the weight. Support for this feature is only enabled in the full flavors of hostapd. Consult the hostapd.conf documentation (Airtime policy configuration) for more information on the inner workings of the exposed settings. Signed-off-by: David Bauer <mail@david-bauer.net>
* base-files: disable LEDs if default state is undefinedDavid Bauer2020-09-112-2/+2
| | | | | | | | | | | | | | | Set the default state for LEDs to off. When a trigger is set, the trigger will turn the LED automatically on. Currently LEDs might stay on, e.g. when the LED trigger is set to a netdev trigger and the interface is never activated or the 'none' trigger is selected without setting the 'default' option to 0 and it's set for the LED indicating the system running state. Using off as a default value is also consistent with the documentation in the OpenWrt wiki. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: improve the description of fs-nfs-v4Bob Cai2020-09-101-1/+1
| | | | | | | | | | | TITLE is "NFS4 filesystem client support" (Line 428) but the description is "Kernel module for NFS v4 support" (Line 438). Use "Kernel module for NFS v4 client support" on line 438. Signed-off-by: Bob Cai <1119283622@qq.com> [commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* rpcd: update to the latest masterRafał Miłecki2020-09-101-3/+3
| | | | | | rc: new ubus object for handling /etc/init.d/ scripts Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* rssileds: update maintainer email addressDaniel Golle2020-09-101-1/+1
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* wireguard-tools: bump to 1.0.20200827Jason A. Donenfeld2020-09-091-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | * ipc: split into separate files per-platform This is in preparation for FreeBSD support, which I had hoped to have this release, but we're still waiting on some tooling fixes, so hopefully next wg(8) will support that. Either way, the code base is now a lot more amenable to adding more kernel platform support. * man: wg-quick: use syncconf instead of addconf for strip example Simple documentation fix. * pubkey: isblank is a subset of isspace * ctype: use non-locale-specific ctype.h In addition to ensuring that isalpha() and such isn't locale-specific, we also make these constant time, even though we're never distinguishing between bits of a secret using them. From that perspective, though, this is markedly better than the locale-specific table lookups in glibc, even though base64 characters span two cache lines and valid private keys must hit both. This may be useful for other projects too: https://git.zx2c4.com/wireguard-tools/tree/src/ctype.h Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* openvpn: fix shell compare operator in openvpn.initMartin Schiller2020-09-092-2/+2
| | | | | | | | Don't use bash syntax, because /bin/sh is used here. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [bump PKG_RELEASE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mac80211: update encap offload patches to the latest versionFelix Fietkau2020-09-0917-149/+1199
| | | | | | | Minor cleanup and code reorganization, along with a change to not disable offload anymore when a tkip or sw crypto key is added Signed-off-by: Felix Fietkau <nbd@nbd.name>
* wireguard: bump to 1.0.20200908Jason A. Donenfeld2020-09-091-2/+2
| | | | | | | | | | | | | | | * compat: backport kfree_sensitive and switch to it * netlink: consistently use NLA_POLICY_EXACT_LEN() * netlink: consistently use NLA_POLICY_MIN_LEN() * compat: backport NLA policy macros Backports from upstream changes. * peerlookup: take lock before checking hash in replace operation A fix for a race condition caught by syzkaller. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* hostapd: add UCI support for Hotspot 2.0Daniel Golle2020-09-083-3/+107
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* netifd: update to git HEADDaniel Golle2020-09-081-3/+3
| | | | | | | | | | | | | | | | | 3d9bd73 utils: fix check_pid_path to work with deleted file as well 330f403 vlan: initialize device ifname earlier at creation time c057e71 device: do not check state from within device_init cb0c07b system-dummy: fix resolving ifindex ccd9ddc bridge: add support for turning on vlan_filtering 82bcb64 bridge: add support for adding vlans to a bridge 0e8cea0 bridge: add support for VLAN filtering 6086b63 config: enable bridge vlan filtering by default for bridges that define VLANs ac0710b device: look up full device name before traversing vlan chain e32e21e bridge: flush vlan list on bridge free 645ceed interface-ip: clear host bits of the device prefix d7b614a netifd-wireless: parse 'osen' encryption Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* dropbear: Enable Ed25519 for normal devicesPaul Spooren2020-09-062-3/+4
| | | | | | | | | | | | | | | | | | | | The Ed25519 key pairs are much shorter than RSA pairs and are supported by default in OpenSSH. Looking at websites explaining how to create new SSH keys, many suggest using Ed25519 rather than RSA, however consider the former as not yet widely established. OpenWrt likely has a positive influence on that development. As enabling Ed25519 is a compile time option, it is currently not possible to install the feature via `opkg` nor select that option in an ImageBuilder. Due to the size impact of **12kB** the option should only be enabled for devices with `!SMALL_FLASH`. This approach seems cleaner than splitting `dropbear` into two packages like `dropbear` and `dropbear-ed25519`. Signed-off-by: Paul Spooren <mail@aparcar.org>
* util-linux: Fix build when libmagic is presentRosen Penev2020-09-061-1/+2
| | | | | | | | | | | | | | | | When the libmagic from the file package in the packages feed was also compiled and provided its libmagic.so file, util-linux tried to link against it. Avoid this by explicitly disable libmagic support. This fixes the following build error: Package more is missing dependencies for the following libraries: libmagic.so.1 Fixes: 36d9ed360a34 ("util-linux: update to 2.36") Acked-by: Sebastian Kemper <sebastian_ml@gmx.net> Signed-off-by: Rosen Penev <rosenp@gmail.com> [Add commit description] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* wolfssl: Activate link time optimization (LTO)Hauke Mehrtens2020-09-061-2/+3
| | | | | | | | | | | The ipk sizes for mips_24Kc change like this: old: libwolfssl24_4.5.0-stable-1_mips_24kc.ipk 391.545 new: libwolfssl24_4.5.0-stable-2_mips_24kc.ipk 387.439 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* iw: Update to version 5.8Hauke Mehrtens2020-09-063-723/+53
| | | | | | | | | | | | | The ipk sizes for mips_24Kc change like this: old: iw_5.4-1_mips_24kc.ipk 35.767 iw-full_5.4-1_mips_24kc.ipk 68.423 new: iw_5.8-1_mips_24kc.ipk 36.883 iw-full_5.8-1_mips_24kc.ipk 71.992 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* nftables: Activate link time optimization (LTO)Hauke Mehrtens2020-09-061-1/+4
| | | | | | | | | | | | | The ipk sizes for mips_24Kc change like this: old: nftables-json_0.9.6-1_mips_24kc.ipk 231.968 nftables-nojson_0.9.6-1_mips_24kc.ipk 204.731 new: nftables-json_0.9.6-2_mips_24kc.ipk 221.894 nftables-nojson_0.9.6-2_mips_24kc.ipk 193.932 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* libnftnl: Activate link time optimization (LTO)Hauke Mehrtens2020-09-061-2/+3
| | | | | | | | | | | The ipk sizes for mips_24Kc change like this: old: libnftnl12_1.1.7-1_mips_24kc.ipk 47.459 new: libnftnl12_1.1.7-2_mips_24kc.ipk 45.742 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* jansson: Activate link time optimization (LTO)Hauke Mehrtens2020-09-061-1/+4
| | | | | | | | | | | The ipk sizes for mips_24Kc change like this: old: jansson4_2.13.1-1_mips_24kc.ipk 19.171 new: jansson4_2.13.1-2_mips_24kc.ipk 18.936 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* nftables: Update to version 0.9.6Hauke Mehrtens2020-09-061-2/+2
| | | | | | | | | | | | | The ipk sizes for mips_24Kc change like this: old: nftables-json_0.9.3-1_mips_24kc.ipk 220.262 nftables-nojson_0.9.3-1_mips_24kc.ipk 192.937 new: nftables-json_0.9.6-1_mips_24kc.ipk 231.968 nftables-nojson_0.9.6-1_mips_24kc.ipk 204.731 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* libnftnl: Update to version 1.1.7Hauke Mehrtens2020-09-061-2/+2
| | | | | | | | | | | The ipk sizes for mips_24Kc change like this: old: libnftnl12_1.1.5-1_mips_24kc.ipk 46.252 new: libnftnl12_1.1.7-1_mips_24kc.ipk 47.459 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* jansson: Update to version 2.13.1Hauke Mehrtens2020-09-061-2/+3
| | | | | | | | | | | | | This also sets the ABI_VERSION as this is a versioned shared library. The ipk sizes for mips_24Kc change like this: old: jansson_2.12-1_mips_24kc.ipk 18.692 new: jansson4_2.13.1-1_mips_24kc.ipk 19.171 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath25: add back target supportAdrian Schmutzler2020-09-061-3/+7
| | | | | | | | | | | | Discussion on the mailing list reveals that this target has active users. As we are finally able to upgrade this target to kernel 5.4, add it back to master. This reverts commit 7d29a5571403 ("ath25: drop target") and immediately moves the relevant files to 5.4, without touching the content. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* base-files: support label-property-less in get_dt_ledsChristian Lamparter2020-09-052-2/+3
| | | | | | | | | | | | | | | | | | | | | | | The LED's "label" property has been deprecated in upstream by: |commit c5d18dd6b64e09dd6984bda9bdd55160af537a8c |Author: Jacek Anaszewski <jacek.anaszewski@gmail.com> |Date: Sun Jun 9 20:19:04 2019 +0200 | | dt-bindings: leds: Add properties for LED name construction | | Introduce dedicated properties for conveying information about | LED function and color. Mark old "label" property as deprecated. | | Additionally function-enumerator property is being provided | for the cases when neither function nor color can be used | for LED differentiation. in order to be somewhat prepared, this patch adds a fallback as a last resort to make the current led code work by falling back to the node-name as the "label". Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ppp: update to latest git HEADHans Dedecker2020-09-051-3/+3
| | | | | | | af30be0 Fix setting prefix for IPv6 link-local addresss 0314df4 Disable asking password again when prompt program returns 128 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* firewall: bump to latest HEADDavid Bauer2020-09-051-3/+3
| | | | | | | 8c2f9fa fw3: zones: limit zone names to 11 bytes 78d52a2 options: fix parsing of boolean attributes Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: add preliminary support for enabling 802.11ax in configFelix Fietkau2020-09-041-12/+37
| | | | | | No advanced features are configurable yet, just basic enabling of HE modes Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libselinux: package executables into -utilsDaniel Golle2020-09-041-0/+13
| | | | | | | Add new package libselinux-utils containing the executable utilities included with libselinux. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for HooToo HT-TM05Russell Morris2020-09-032-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port. Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli). Specifications: SOC: MediaTek MT7620N BATTERY: 10400mAh WLAN: 802.11bgn LAN: 1x 10/100 Mbps Ethernet USB: 1x USB 2.0 (Type-A) RAM: 64 MB FLASH: GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz Flash itself specified to 80 MHz, but speed limited by mt7620 SPI fast-read enabled (m25p) LED: Status LED (blue after boot, green with WiFi traffic 4 leds to indicate power level of the battery (unable to control) INPUT: Power, reset button MAC assignment based on vendor firmware: 2.4 GHz *:b4 (factory 0x04) LAN/label *:b4 (factory 0x28) WAN *:b5 (factory 0x2e) Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - Installation from TFTP (recovery) - OpenWRT sysupgrade (Preserving and non-preserving), through the usual ways: command line and LuCI - LEDs (except as noted above) - Button (reset) - I2C, which is needed for reading battery charge status and level - U-Boot environment / variables (from U-Boot, and OpenWrt) Installation: - Download the needed OpenWrt install files, place them in the root of a clean TFTP server running on your computer. Rename the files as, - ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel - ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs - Plug the router into your computer via Ethernet - Set your computer to use 10.10.10.254 as its IP address - With your router shut down, hold down the power button until the first white LED lights up. - Push and hold the reset button and release the power button. Continue holding the reset button for 30 seconds or until it begins searching for files on your TFTP server, whichever comes first. - The router (10.10.10.128) will look for your computer at 10.10.10.254 and install the two files. Once it has finished installation, it will automatically reboot and start up OpenWrt. - Set your computer to use DHCP for its IP address Notes: - U-Boot environment can be modified, u-boot-env is preserved on initial install or sysupgrade - mtd-concat functionality is included, to leave a "hole" for u-boot-env, combining the OEM kernel and rootfs partitions I would like to thank @mpratt14 and @xabolcs for their help getting the lzma loader to work! Signed-off-by: Russell Morris <rmorris@rkmorris.us> [drop changes in image/Makefile, fix indent and PKG_RELEASE in uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift, add COMPILE to Device/Default] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* policycoreutils: add nls.mkRosen Penev2020-09-031-1/+2
| | | | | | Fixes compilation under uClibc-ng. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: remove obsolete kernel version switches for 4.14Adrian Schmutzler2020-09-0223-1083/+34
| | | | | | | | | | This removes switches dependent on kernel version 4.14 as well as several packages/modules selected only for that version. This also removes sched-cake-virtual, which is not required anymore now that we have only one variant of cake. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* samsung: drop targetAdrian Schmutzler2020-09-021-2/+2
| | | | | | | | | This target is still on kernel 4.14, and no attempt has been made to update it to a newer kernel. Since we already are two LTS versions ahead of that the target is dropped, as the chance of somebody bumping it will only decrease with time. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath25: drop targetAdrian Schmutzler2020-09-021-7/+3
| | | | | | | | | | | | | This target still only works with kernel 4.14, and not so recent attempts of getting newer kernel versions supported did not lead to success. Therefore, drop the target, as we are already two LTS kernel versions ahead and it does not seem like anybody will pick up the work. Patchwork series: https://patchwork.ozlabs.org/project/openwrt/list/?series=169991&state=* Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mbedtls: update to 2.16.8Magnus Kroken2020-09-022-25/+25
| | | | | | | | | | | | | | | | | This release of Mbed TLS provides bug fixes and minor enhancements. This release includes fixes for security issues and the most notable of them are described in more detail in the security advisories. * Local side channel attack on RSA and static Diffie-Hellman * Local side channel attack on classical CBC decryption in (D)TLS * When checking X.509 CRLs, a certificate was only considered as revoked if its revocationDate was in the past according to the local clock if available. Full release announcement: https://github.com/ARMmbed/mbedtls/releases/tag/v2.16.8 Signed-off-by: Magnus Kroken <mkroken@gmail.com>
* base-files: fix comment typo in lib/functions/network.shWalter Sonius2020-09-021-1/+1
| | | | | | | | Fix typo in comment. Signed-off-by: Walter Sonius <walterav1984@gmail.com> [commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* hostapd: add hs20 variantDaniel Golle2020-09-011-1/+21
| | | | | | Add hostapd variant compiled with support for Hotspot 2.0 AP features. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: remove an obsolete patch that is no longer doing anything usefulFelix Fietkau2020-09-018-32/+17
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: add more AQL fixes/improvementsFelix Fietkau2020-09-012-0/+72
| | | | | | Fix aggregation length estimation, add HE and VHT160 support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* refpolicy: skip building docsDaniel Golle2020-09-012-1/+13
| | | | | | | Building docs requires xmllint and other bulky things being present on the host. Skip that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* libaudit: add host-build required by policycoreutils/hostDaniel Golle2020-09-011-9/+25
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* libsemanage: host-build depends on renamed libaudit packageDaniel Golle2020-09-011-1/+1
| | | | | Fixes: efdf619f21 ("audit: build only libaudit") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ugps: update to the latest versionHauke Mehrtens2020-09-011-3/+3
| | | | | | 511a5b3 ugps: fix 64-bit time_t Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-12 09:45:17 +0000