aboutsummaryrefslogtreecommitdiffstats
path: root/package
Commit message (Collapse)AuthorAgeFilesLines
* perf: Depend on libbfd and libopcodes when enabledFlorian Fainelli2022-01-271-1/+2
| | | | | | | | bpftool will enabled libbfd and libopcodes which gets picked up by perf as libraries to link against. Add those missing dependencies when either of these packages are enabled. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* netfilter: correct some dependenciesTiago Gaspar2022-01-271-2/+2
| | | | | | | | | | | | nf-nathelper-extra and nf-conntrack-netlink had iptables related dependencies, yet, when looking for the respective kernel symbols and checking it's dependencies it was confirmed that iptables wasn't required and that these were either it's own moodule or tool independent (nftables or iptables). Correct these and make sure no unneeded extras are pulled in. Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
* uboot-mediatek: update to version 2022.01Daniel Golle2022-01-2321-111/+62
| | | | | | | Tested on BananaPi R2 (SD, eMMC), BananaPi R64 (SD, eMMC, SPI-NAND) and UniElec U7623-02 (eMMC). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: add configuration for UniElec U7623 boardDaniel Golle2022-01-231-0/+4
| | | | | | | Add U-Boot env settings to allow accessing the environment using fw_printenv and fw_setenv tools on the UniElec U7623 board. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: update build for the U7623-02 boardDaniel Golle2022-01-236-70/+273
| | | | | | | Brings bootmenu and production/recovery dual-boot scheme like on the BPi-R2, BPi-R64, E8450 and UniFi 6 LR. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* netifd: update to git HEADHans Dedecker2022-01-231-3/+3
| | | | | | ed71876 iprule: add support for uidrange Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ucode: add temporary fix for integer formatting on 32bit systemsJo-Philipp Wich2022-01-232-1/+12
| | | | | | | | | | | | The ucode VM always passes 64bit integer values to sprintf implementation while the `%d` format expects 32bit integers on 32bit platforms, leading to incorrect formatting results. Temporarily solve the issue by casting the numeric argument to int until a more thorough fix arrives with the next update. Fixes: FS#4234 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* util-linux: Add tasksetHauke Mehrtens2022-01-211-0/+15
| | | | | | | This adds the taskset application from util Linux. It is already built, but not packaged yet. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* ltq-vdsl-mei: Remove static linkingHauke Mehrtens2022-01-211-0/+47
| | | | | | | | | This removes -static compile option. The -static option tells GCC to link this statically with the libc, which we do not want in OpenWrt. We want to link everything dynamically to the libc. This fixes a compile problem with glibc. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipip: add 'nohostroute' optionMatthew Hagan2022-01-192-3/+6
| | | | | | | | Add the nohostroute option as available for gre and wg tunnels to allow the user to prevent explicit creation of a route to the peer address. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ustream-ssl: update to Git version 2022-01-16Hauke Mehrtens2022-01-161-4/+4
| | | | | | 868fd88 ustream-openssl: wolfSSL: Add compatibility for wolfssl >= 5.0 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: Add support for OpenMesh OM2P v1Sven Eckelmann2022-01-161-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR7240 rev 2 * 350/350/175 MHz (CPU/DDR/AHB) * 32 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 18-24V passive POE (mode B) + used as WAN interface - eth1 + builtin switch port 4 + used as LAN interface * 12-24V 1A DC * external antenna The device itself requires the mtdparts from the uboot arguments to properly boot the flashed image and to support dual-boot (primary + recovery image). Unfortunately, the name of the mtd device in mtdparts is still using the legacy name "ar7240-nor0" which must be supplied using the Linux-specfic DT parameter linux,mtd-name to overwrite the generic name "spi0.0". Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* mtd-utils: update to 2.1.4Nick Hainke2022-01-162-6/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changes from 2.1.3 to 2.1.4: Features: - ubiscan debugging and statistics utility Fixes: - Some mtd-tests erroneously using sub-pages instead of the full page size - Buffer overrun in fectest - Missing jffs2 kernel header in the last release, leading to build failures on some systems. Changes from 2.1.2 to 2.1.3: Features: flashcp: Add new function that copy only different blocks flash_erase: Add flash erase chip Add flash_otp_erase Add an ubifs mount helper Add nandflipbits tool Fixes: mkfs.ubifs: Fix runtime assertions when running without crypto mtd-utils: Use AC_SYS_LARGEFILE Fix test binary installation libmtd: avoid divide by zero ubihealthd: fix UBIFS build dependency mkfs.ubifs: remove OPENSSL_no_config() misc-utils: Add fectest to build system mkfs.ubifs: Fix build with SELinux Fix typos found by Debian's lintian tool Fix jffs2 build if zlib or lzo headers are not in default paths Signed-off-by: Nick Hainke <vincent@systemli.org>
* kernel: add missing kmod+regmap-i2c dependency for NCT7802Y moduleChristian Lamparter2022-01-151-1/+1
| | | | | | | | | | x86, mt7623 and others buildbot failed due to: |Package kmod-hwmon-nct7802 is missing dependencies for the following libraries: |regmap-core.ko |regmap-i2c.ko Fixes: 1ed50b92d157 ("package: kernel: add driver module for NCT7802Y") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mvebu: cortexa9: Add support for Ctera C200-V2Pawel Dembicki2022-01-151-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 2-Bay NAS - maximum two 3.5" Harddisks Hardware: - SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC) - Ram: 1GB (2x Nanya NT5CC512M8DN-D1) - NAND Flash: 256MB (ESMT F59L2G81A-25T) - Lan: 1x GBE (Marvell 88E1318-NNB2) - Storage: 2x SATA HDD 3.5" Slot - USB: 2x USB 3.0 port (Renesas uPD720202) - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND) - LEDs: 13x GPIO controlled - Buttons: 2x GPIO controlled Known issues: - Buzzer is unused due lack of proper driver - USB1/2 usbport ledtrigger won't work (through DT) - Renesas uPD720202 requires firmware file. It's possible to find non-free binary. Please look for 'UPDATE.mem' file and put in into '/lib/firmware/renesas_usb_fw.mem' file. Installation: - Apply factory initramfs image via stock web-gui. - Do sysupgrade to make installation complete. Back to stock: - OpenWrt rootfs partition use unused space after stock firmware. - Full revert is possible. - Login via ssh and run: ## ctera_c200-v2_back_to_factory start ## . /lib/functions.sh part=$(find_mtd_part "active_bank") active_bank=$(strings "$part" | grep bank) if [ "$active_bank" = "bank1" ]; then echo "bank2" > /tmp/change_bank else echo "bank1" > /tmp/change_bank fi mtd write /tmp/change_bank active_bank reboot ## ctera_c200-v2_back_to_factory end ## Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (put back-to-stock script into commit message, removed dup. SUBPAGESIZE var, added 01_leds for non-working dt-usb-port trigger) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* package: kernel: add driver module for NCT7802YPawel Dembicki2022-01-151-0/+15
| | | | | | | | | | | | This commit add package with hwmon-nct7802 module. This driver implements support for the Nuvoton NCT7802Y hardware monitoring chip. NCT7802Y supports 6 temperature sensors, 5 voltage sensors, and 3 fan speed sensors. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (fixed c&p'ed module description) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ASUS RT-ACRH17/RT-AC42UJoshua Roys2022-01-153-0/+2
| | | | | | | | | | | | | | | | | | | | | SOC: IPQ4019 CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d DRAM: 256 MB NAND: 128 MiB Macronix MX30LF1G18AC ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN) USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4 INPUT: 1x WPS, 1x Reset LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed with an intermediary initramfs image, the jffs2 ubi volume deleted, and then finally a sysupgrade with the final image performed. Signed-off-by: Joshua Roys <roysjosh@gmail.com> (added ALT0) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* hostapd: add op-class to get_status outputDavid Bauer2022-01-141-2/+9
| | | | | | Include the current operation class to hostapd get_status interface. Signed-off-by: David Bauer <mail@david-bauer.net>
* netifd: update to git HEADHans Dedecker2022-01-141-3/+3
| | | | | | 3043206 system: fix compilation with glibc 2.34 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* iptables: enable nftable support by defaultPaul Spooren2022-01-141-2/+2
| | | | | | | | | | | | | | OpenWrt plans to move over to firewall4 which uses nftables under the hood. To allow a smooth migration the package `iptables-nft` offer a transparent wrapper to apply iptables rules to nftables. Without the config option for nftables the package isn't installed and therefore can't be tested. This commit enabled it and therefore provides the wrapper. The size of the iptables package increases from 25436 to 26500 Bytes. Signed-off-by: Paul Spooren <mail@aparcar.org>
* netifd: update to git HEADHans Dedecker2022-01-121-3/+3
| | | | | | | | 96902e8 Revert "netifd: add devtype to ubus call" 29e6acf netifd: add devtype to ubus call 7ccbf08 netifd: add devtype to ubus call Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* procd: update to git HEADDaniel Golle2022-01-121-3/+3
| | | | | | | | | | ca6c35c uxc: usage message cosmetics e083dd4 uxc: fix two minor issues reported by Coverity 35dfbff procd: jail/cgroups: correctly enable "rdma" when requested 3b3ac64 procd: mount /dev with noexec ac2b8b3 procd: clean up /dev/pts mounts Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* firewall: update to latest HEADKevin Darbyshire-Bryant2022-01-101-3/+3
| | | | | | | | | 0f16ea5 options.c: add DSCP code LE Least Effort 24ba465 firewall3: remove redundant syn check df1306a firewall3: fix locking issue 3624c37 firewall3: support table load on access on Linux 5.15+ Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: Add support for OpenMesh OM5P-AC v1Sven Eckelmann2022-01-091-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh OM5P-ANSven Eckelmann2022-01-091-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9344 rev 2 * 560/450/225 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 1T1R 2.4 GHz Wi-Fi * 2T2R 5 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + 10/100 Mbps Ethernet + builtin switch port 1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* opkg: update to git HEAD of 2022-01-09Daniel Golle2022-01-091-3/+3
| | | | | | | | | | db7fb64 libopkg: pkg_hash: prefer to-be-installed packages 2edcfad libopkg: set 'const' attribute for argv This should fix the ImageBuilder problems people are having since we introduced the 'uci-firewall' providers. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* firewall4: bump to git HEADStijn Tintel2022-01-091-3/+3
| | | | | | | | | | | | 9a509d4 ruleset.uc: consolidate ip and ip6 offload 21f311d ruleset.uc: don't trim newline before comment sign f121383 tests: enable flow offloading in tests 550df40 tests: add test for unknown defaults option 47c5a5b tests: add test for deprecated rule option 69a89d6 tests: add test for unknown rule option 07579df fw4.uc: handle interface zone option Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add kmod-usb-net-lan78xxJosef Schlehofer2022-01-081-0/+17
| | | | | | | | | | | | | | | | | Add kernel module for Microchip LAN78XX based USB 2 & USB 3 10/100/1000 Ethernet adapters. [1] This kernel module is required for the Seeed Studio's Mini Router based on RPI CM4 [2]. [1] <https://cateee.net/lkddb/web-lkddb/USB_LAN78XX.html> [2] <https://www.seeedstudio.com/Dual-GbE-Carrier-Board-with-4GB-RAM-32GB-eMMC-RPi-CM4-Case-p-5029.html> Link: <https://github.com/openwrt/openwrt/pull/4893> Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (added kmod-phy-microchip and kmod-fixed-phy dependencies, rpi3 needs lan78xx but has it built-in) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: provide kmod-fixed-phy as separate kmodChristian Lamparter2022-01-081-2/+17
| | | | | | | | | | Almost all targets have the fixed-phy feature built into the kernel. One big exception is x86. This caused a problem with the upcoming LAN78xx usb driver. Hence this patch breaks out the fixed-phy from of_mdio (which didn't include the .ko) and puts into a separate module. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: add kmod-phy-microchipChristian Lamparter2022-01-081-0/+15
| | | | | | | | phy drivers for Microchip's LAN88xx PHYs. This is needed for the "LAN7801" variant of the upstream lan78xx usb ethernet driver. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* elfutils: Add missing musl-fts dependencyFlorian Fainelli2022-01-071-1/+1
| | | | | | | | libdw depends on libfts.so when building with the musl-libc library, add this missing dependency. Fixes: 6835ea13f0fa ("elfutils: update to 0.186") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* linux-firmware: add new package r8152-firmwareMarty Jones2022-01-082-1/+15
| | | | | | | | | | | | | | Linux upstream commit https://github.com/torvalds/linux/commit/9370f2d05a2a150b0aa719a3070b26d478180df3 add load firmware file through request_firmware,this affect the nanopi r2s and some USB adapters in kernel 5.10 with this error: 'r8152 4-1:1.0: unable to load firmware patch rtl_nic/rtl8153b-2.fw' This patch split the USB NIC firmware files from r8169 firmware, and adds r8152-firmware to r8152 driver. Add kmod-usb-net-cdc-ncm to support RTL8156A and RTL8156B 2.5G ethernet adapters supported since v5.13-rc1. https://github.com/torvalds/linux/commit/195aae321c829dd1945900d75561e6aa79cce208 Signed-off-by: Marty Jones <mj8263788@gmail.com>
* ltq-ifxos: update to 1.7.1Jan Hoffmann2022-01-086-234/+34
| | | | | | Signed-off-by: Jan Hoffmann <jan@3e8.eu> [fix warnings, switch to tag tarball, update patches] Signed-off-by: Andre Heider <a.heider@gmail.com>
* ltq-vdsl: move to the default device name /dev/dsl_cpe_api/0Andre Heider2022-01-083-14/+3
| | | | | | | This makes patching it for ltq-vdsl-app unnecessary and paves the way for VRX518 support. Signed-off-by: Andre Heider <a.heider@gmail.com>
* busybox: update to 1.35.0Hannu Nyman2022-01-0810-208/+314
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Update busybox to 1.35.0 * refresh patches Config refresh: Refresh commands, run after busybox is first built once: cd package/utils/busybox/config/ ../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0 cd .. ./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0/.config > Config-defaults.in Manual edits needed after config refresh: * Config-defaults.in: OpenWrt config symbol IPV6 logic applied to BUSYBOX_DEFAULT_FEATURE_IPV6 * Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec) * Config-defaults.in: OpenWrt logic applied to BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917) * config/editors/Config.in: Add USE_GLIBC dependency to BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090) * config/shell/Config.in : change at "Options common to all shells" the symbol SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH (discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html Apparently our script does not see the hidden option while prepending config options with "BUSYBOX_CONFIG_" which leads to a missed dependency when the options are later evaluated.) * Edit Config.in files by adding quotes to sourced items in config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f) Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* mbedtls: enable session ticketsGlenn Strauss2022-01-081-18/+0
| | | | | | | | | | session tickets are a feature of TLSv1.2 and require less memory and overhead on the server than does managing a session cache Building mbedtls with support for session tickets will allow the feature to be used with lighttpd-1.4.56 and later. Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
* elfutils: update to 0.186Sergey V. Lobanov2022-01-087-145/+30
| | | | | | | | | | | | | | | | | | | | | Upstreamed patches (deleted): 0001-ppc_initreg.c-Incliude-asm-ptrace.h-for-pt_regs-defi.patch - https://sourceware.org/git/?p=elfutils.git;a=commitdiff;h=8382833a257b57b0d288be07d2d5e7af6c102869 110-no-cdefs.patch - https://sourceware.org/git/?p=elfutils.git;a=commitdiff;h=d390548df1942e98a1d836269a5e41ba52e121f1 Auto-refreshed: 006-Fix-build-on-aarch64-musl.patch 101-no-fts.patch Manually updated and refreshed: 005-build_only_libs.patch 003-libintl-compatibility.patch 100-musl-compat.patch Disabled _obstack_free check (via configure vars) Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
* ramips: add support for Linksys EA6350 v4Nick McKinney2022-01-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621DAT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 128 MB NAND - Ethernet: 5x 1GiE MT7530 - WiFi: MT7603/MT7613 - USB: 1x USB 3.0 This is another MT7621 device, very similar to other Linksys EA7300 series devices. Installation: Upload the generated factory.bin image via the stock web firmware updater. Reverting to factory firmware: Like other EA7300 devices, this device has an A/B router configuration to prevent bricking. Hard-resetting this device three (3) times will put the device in failsafe (default) mode. At this point, flash the OEM image to itself and reboot. This puts the router back into the 'B' image and allows for a firmware upgrade. Troubleshooting: If the firmware will not boot, first restore the factory as described above. This will then allow the factory.bin update to be applied properly. Signed-off-by: Nick McKinney <nick@ndmckinney.net>
* utils/mdadm: fix build on hosts without /run dirSergey V. Lobanov2022-01-081-1/+1
| | | | | | | CHECK_RUN_DIR=0 must be a part of MAKE_FLAGS, not MAKE_VARS, otherwise it is not possible to compile mdadm on host without /run dir. Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
* toolchain: glibc: Update to version 2.34Hauke Mehrtens2022-01-071-4/+1
| | | | | | | | | | | | glibc version 2.34 does not provide versioned shared libraries any more, it only provides shared libraries using the ABI version. Do not try to copy them any more. The functions from libpthread and librt were integrated into the main binary, the libpthread.so and librt.so are only used for backwards compatibility any more. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* firewall4: bump to git HEADStijn Tintel2022-01-061-2/+2
| | | | | | main.uc: fix device gathering Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* firewall4: fix syntax error in dependency specJo-Philipp Wich2022-01-061-1/+1
| | | | | Fixes: ae60af8572 ("firewall4: order DEPENDS alphabetically") Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* firewall/firewall4: provide uci-firewallStijn Tintel2022-01-062-2/+4
| | | | | | | | | | | | | | | | Provide uci-firewall via PROVIDES in both firewall and firewall4. This will allow us to change the dependency of luci-app-firewall to uci-firewall, making it possible to use it with either implementation. Move CONFLICTS from firewall4 to firewall, to solve this recursive dependency problem: tmp/.config-package.in:307:error: recursive dependency detected! tmp/.config-package.in:307: symbol PACKAGE_firewall is selected by PACKAGE_firewall4 tmp/.config-package.in:328: symbol PACKAGE_firewall4 depends on PACKAGE_firewall Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Jo-Philipp Wich <jo@mein.io>
* firewall4: bump to git HEADStijn Tintel2022-01-061-4/+4
| | | | | | | | | | | | | | | | 4ead2a6 treewide: move executables to /sbin 9ebc2f4 fw4.uc: filter duplicates in fw4.set 85b74f3 treewide: support flow offloading be3b4e6 treewide: support hardware flow offloading 38889b7 treewide: support set timeout 31c7550 fw4.uc: do not skip defaults with invalid option 334a127 fw4.uc: introduce DEPRECATED flag 7a0d38f fw4.uc: add _name as deprecated option 5e7ad3b fw4.uc: don't fail on unknown options be5f4e3 fw4.uc: allow use of cidr in ipsets Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Jo-Philipp Wich <jo@mein.io>
* firewall4: order DEPENDS alphabeticallyStijn Tintel2022-01-061-1/+5
| | | | | | | Add some line breaks while at at, to improve readability. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Jo-Philipp Wich <jo@mein.io>
* firewall4: drop kmod-ipt-nat from CONFLICTSStijn Tintel2022-01-061-1/+1
| | | | | | | | The limitation of not being able to use iptables and nft nat at the same time exists only in kernels before 4.18. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Jo-Philipp Wich <jo@mein.io>
* ltq-deu: disable arc4 algorithmDaniel Kestrel2022-01-061-4/+4
| | | | | | | ARC4 was used for WEP, which is not secure anymore. Therefor it is disabled in the driver, but the code is not removed for now. Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
* ltq-deu: add aes_gcm algorithmDaniel Kestrel2022-01-061-0/+313
| | | | | | | | | | | | The lantiq AES hardware does not support the gcm algorithm. But it can be implemented in the driver as a combination of the aes_ctr algorithm and the xor plus gfmul operations for the hashing. Due to the wrapping of the several algorithms and the inefficient 16 byte block by 16 byte block invokation in the kernel implementations, this driver is about 3 times faster for the larger block sizes. Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
* ltq-deu: change PKG_RELEASE to AUTORELEASEDaniel Kestrel2022-01-061-1/+1
| | | | | | As per suggestion by adschm, PKG_RELEASE is set to AUTORELEASE. Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
* ltq-deu: remove redundant code for setting the key in aesDaniel Kestrel2022-01-061-120/+4
| | | | | | | | | | After adding xts and cbcmac the aes algorithm source had three sections for setting the aes key to the hardware which are identical. Method aes_set_key_hw was created which is now called from within the spinlock secured control sections in methods ifx_deu_aes, ifx_deu_aes_xts and aes_cbcmac_final_impl and reduces the size of ifxmips_aes.c. Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 10:54:45 +0000