aboutsummaryrefslogtreecommitdiffstats
path: root/package
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com> (cherry picked from commit 78c3534645958c123aa82cec9926a34eed5dd5dd)
* mac80211: fix QCA9561 PA biasThibaut VARÈNE2022-04-181-0/+47
| | | | | | | | | | | | | | | This patch fixes an invalid TX PA DC bias level on QCA9561, which results in a very low output power and very low throughput as devices are further away from the AP (compared to other 2.4GHz APs), following a suggestion from nbd[1]. This patch has been submitted upstream[2]. [1] https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name [2] https://lore.kernel.org/linux-wireless/20220417145145.1847-1-hacks+kernel@slashdirt.org/ Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit 7dc52a78ae2c2f748a0c0c4adcb13979260b3498)
* readline: add host PICRosen Penev2022-04-171-0/+1
| | | | | | | | Python seems to fail to link to libreadline properly because of this. Not a fatal error but an error nontheless. Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit b363f7488643882b9c53a1e2c6db2a110703cc1d)
* linux-firmware: Update to version 20220411Hauke Mehrtens2022-04-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following files used in OpenWrt changed: amd64-microcode/lib/firmware/amd-ucode/microcode_amd_fam17h.bin amd64-microcode/lib/firmware/amd-ucode/microcode_amd_fam19h.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_mec.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_smc.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_sos.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_ta.bin amdgpu-firmware/lib/firmware/amdgpu/aldebaran_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/arcturus_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_ce.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_me.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_mec.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_smc.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_sos.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_ta.bin amdgpu-firmware/lib/firmware/amdgpu/beige_goby_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_ce.bin amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_me.bin amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_mec.bin amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/dcn_3_1_6_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_ce.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_me.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_mec.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_smc.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_sos.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_ta.bin amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_ce.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_me.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_mec.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_asd.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_ce.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_me.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_mec.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_ta.bin amdgpu-firmware/lib/firmware/amdgpu/green_sardine_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_asd.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_ce.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_me.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_mec.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_sos.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_ta.bin amdgpu-firmware/lib/firmware/amdgpu/navi10_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_asd.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_sdma1.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_sos.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_ta.bin amdgpu-firmware/lib/firmware/amdgpu/navi12_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/navi14_asd.bin amdgpu-firmware/lib/firmware/amdgpu/navi14_smc.bin amdgpu-firmware/lib/firmware/amdgpu/navi14_sos.bin amdgpu-firmware/lib/firmware/amdgpu/navi14_ta.bin amdgpu-firmware/lib/firmware/amdgpu/navi14_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_ce.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_me.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_mec.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_smc.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_sos.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_ta.bin amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_asd.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_ce.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_me.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_mec.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_ta.bin amdgpu-firmware/lib/firmware/amdgpu/picasso_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_asd.bin amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_ta.bin amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_toc.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_asd.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_ce.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_me.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_mec.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_ta.bin amdgpu-firmware/lib/firmware/amdgpu/raven2_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/raven_asd.bin amdgpu-firmware/lib/firmware/amdgpu/raven_ce.bin amdgpu-firmware/lib/firmware/amdgpu/raven_me.bin amdgpu-firmware/lib/firmware/amdgpu/raven_mec.bin amdgpu-firmware/lib/firmware/amdgpu/raven_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/raven_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/raven_ta.bin amdgpu-firmware/lib/firmware/amdgpu/raven_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_asd.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_ce.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_me.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_mec.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_ta.bin amdgpu-firmware/lib/firmware/amdgpu/renoir_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/sdma_5_2_7.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_ce.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_dmcub.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_me.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_mec.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_sdma.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_smc.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_sos.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_ta.bin amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_vcn.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_asd.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_ce.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_me.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_mec.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/vangogh_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_asd.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_ce.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_me.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_mec.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/vega10_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_asd.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_ce.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_me.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_mec.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/vega12_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_asd.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_ce.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_me.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_mec.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/vega20_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_asd.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_ce.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_me.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_mec.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_mec2.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_pfp.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_rlc.bin amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_ta.bin ibt-firmware/lib/firmware/intel/ibt-hw-37.8.10-fw-22.50.19.14.f.bseq iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm iwlwifi-firmware-iwl9260/lib/firmware/iwlwifi-9260-th-b0-jf-b0-46.ucode iwlwifi-firmware-iwl9000/lib/firmware/iwlwifi-9000-pu-b0-jf-b0-46.ucode Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 54d9051c5596814293edd9e6a534c8d1e56e6fcf)
* comgt: support ZTE MF286R modemCezary Jackiewicz2022-04-172-1/+23
| | | | | | | | | | | | | The modem is based on Marvell PXA1826 and uses ACM+RNDIS interface to establish connection with custom commands specific to ZTE modems. Two variants of modems were discovered, some identifying themselves as "ZTE", and others as plain "Marvell", the chipset manufacturer. The modem itself runs a fork of OpenWrt inside, which root shell can be accessed via ADB interface. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit e02fb42c53bad5dd36726c6ef5a46bfe31d2e400)
* comgt: ncm: try to detect interface for ttyACM portsLech Perczak2022-04-171-0/+4
| | | | | | | | | | | | Some modems expose ttyACM as their control ports, which have the "device" symlink pointing one level down in sysfs tree. Try to find network interfaces for them as well, this is commonly used for modems exposing ACM + RNDIS or ACM + ECM interface combinations. Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit ed7957810c0aee04943559be9b0ed23431ee0654)
* comgt: ncm: select first available network interface for deviceLech Perczak2022-04-171-3/+4
| | | | | | | | | | | | | | Some modems expose multiple network interfaces on the same USB device, causing the connection setup script to fail, because glob matching in the detection phase causes 'ls' to output more than one interface name plus their base directories in sysfs. Avoid that by listing the directories explicitly and then selecting first available interface. This is the case for some variants of ZTE MF286R built-in modem, which exposes both RNDIS and CDC-ECM network interfaces, causing the connection setup to fail. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit b2940bb8b2878ce193f2edaee3e7d4c44f4a2065)
* comgt: ncm: allow specification of interface nameLech Perczak2022-04-171-14/+18
| | | | | | | | | | | | | Add ifname property to UCI, which can be used to override the autodetected interface name in case the detection fails due to having none or more than one interface exposed by the modem, which is not explicitly linked to TTY port. This is needed on certain variants of ZTE MF286R built-in modem, which exposes both RNDIS and CDC-ECM interfaces on the modem, on which the automatic detection may select the wrong network interface. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit a67629bbe25ef3d0e159db1e0c6ca81affd06898)
* hostapd: add ubus link-measurements notificationsDavid Bauer2022-04-173-0/+43
| | | | | | | Notify external ubus subscribers of received link-measurement reports. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f6445cfa1acb32676723c49da3e3158b64a4b3d2)
* hostapd: add ubus method for requesting link measurementsDavid Bauer2022-04-171-0/+65
| | | | | | | | | | | Add a ubus method to request link-measurements from connected STAs. In addition to the STAs address, the used and maximum transmit power can be provided by the external process for the link-measurement. If they are not provided, 0 is used as the default value. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 965aa33a18c76bb2d5a1eeb0cfa01501b08e784a)
* hostapd: add support for enabling link measurementsDavid Bauer2022-04-171-0/+10
| | | | | | | | Allow external processes to enable advertisement of link-measurement RRM capability. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 2ca5c3da04c3f05a7477ae484768e03d4ca30711)
* netifd: relax check in dhcp proto handlerDaniel Golle2022-04-151-1/+1
| | | | | | | | | | Checking whether /sbin/udhcpc is a symbolic link breaks using the DHCP proto handler inside procd-ujail where bind-mounts are used for the resolved link. Check whether /sbin/udhcpc is executable instead to allow using the proto handler for DHCP-provisioned containers. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit c5f113c43f43c20555298c8500bf91bffbe1f58b)
* procd: update to git HEADDaniel Golle2022-04-151-3/+3
| | | | | | | | | 6343c3a procd: completely remove tmp-on-zram support 5c5e63f uxc: fix potential NULL-pointer dereference eb03f03 jail: include necessary files for per-netns netifd instance Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 2c8873033e3c0b5a5e8f6080ea3a73fde6a55f39)
* base-files: more robust sysupgrade on NANDDaniel Golle2022-04-151-4/+10
| | | | | | | | | | Make sure sysupgrade on NAND also works in case of UBI volumes having index >9. While at it, also make sure UBI device is detected and abort in case it isn't. Use Shell built-in shorthand ':' instead of 'true'. Fixes #9708 Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 0dbca1b2baf9c26514b517a1e5860f6a5b04d5ae)
* ath79: add support for Yuncore A930Thibaut VARÈNE2022-04-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR - 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN) - 2T2R 802.11b/g/n 2.4GHz Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit a05dcb07241aa83a4416b56201e31b4af8518981)
* ath79: add support for Yuncore XD3200Thibaut VARÈNE2022-04-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit c91df224f54fdd44c9c0487a8c91876f5d273164)
* mac80211: backport minstrel_ht fix for legacy ratesFelix Fietkau2022-04-121-0/+61
| | | | | | | Fixes OFDM rates on 5 GHz Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 5d5afd51772c9a992cb6bb9e0a9dce6feaa3fdef)
* musl-fts: add host buildRosen Penev2022-04-111-0/+2
| | | | | | | This will be used for libselinux. Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit 1fb099341e5879a8c5247020e5056676ba2f0745)
* nftables: add CONFLICT between versionsEneas U de Queiroz2022-04-111-1/+2
| | | | | | | Have nftables-json conflict with nftables-nojson. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit 1135b75d1fd26049a0644b304b7199e4a73c6a08)
* mac80211: Update to version 5.15.33-1Hauke Mehrtens2022-04-1133-439/+85
| | | | | | | | | | | | | | | This updates mac80211 to version 5.15.33-1 which is based on kernel 5.15.33. The removed patches were applied upstream. This new release contains many fixes which were merged into the upstream Linux kernel. This also contains the following new drivers which are needed for ath11k: * net/qrtr/ * drivers/bus/mhi/ Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 3aa96efa24c13c6e0aafa5ad826f3f95a3bd74f9)
* wolfssl: bump to 5.2.0Eneas U de Queiroz2022-04-114-9/+7
| | | | | | | | | | | | | | | | | Fixes two high-severity vulnerabilities: - CVE-2022-25640: A TLS v1.3 server who requires mutual authentication can be bypassed. If a malicious client does not send the certificate_verify message a client can connect without presenting a certificate even if the server requires one. - CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS v1.3 server can have its certificate heck bypassed. If the sig_algo in the certificate_verify message is different than the certificate message checking may be bypassed. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit e89f3e85eb1c1d81294e5d430a91b0ba625e2ec0)
* arm-trusted-firmware-mediatek: remove no longer needed Configure stepDaniel Golle2022-04-101-4/+0
| | | | | | | | | As anyway only the default is called now we can as well also just remove the override for Build/Configure. Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10") Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit dffad93d3e34275b87d97724e64447d8bde537ff)
* dropbear: bump to 2022.82Konstantin Demin2022-04-109-66/+90
| | | | | | | | | | | | | | | | | | | | | | | - update dropbear to latest stable 2022.82; for the changes see https://matt.ucc.asn.au/dropbear/CHANGES - use $(AUTORELEASE) in PKG_RELEASE - use https for all uris - refresh all patches - rewrite patches: - 100-pubkey_path.patch - 130-ssh_ignore_x_args.patch binary/pkg size changes: - ath79/generic, mips: - binary: 215112 -> 219228 (+4116) - pkg: 111914 -> 113404 (+1490) - ath79/tiny, mips: - binary: 172501 -> 172485 (-16) - pkg: 89871 -> 90904 (+1033) Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Konstantin Demin <rockdrilla@gmail.com> (cherry picked from commit 65256aee23a5104eb0c78411fdc73640c0b757ea)
* libmnl: update to 1.0.5Nick Hainke2022-04-101-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changes: Duncan Roe (5): nlmsg: Fix a missing doxygen section trailer build: doc: "make" builds & installs a full set of man pages build: doc: get rid of the need for manual updating of Makefile build: If doxygen is not available, be sure to report "doxygen: no" to ./configure src: doc: Fix messed-up Netlink message batch diagram Fernando Fernandez Mancera (1): src: fix doxygen function documentation Florian Westphal (1): libmnl: zero attribute padding Guillaume Nault (1): callback: mark cb_ctl_array 'const' in mnl_cb_run2() Kylie McClain (1): examples: nfct-daemon: Fix test building on musl libc Laura Garcia Liebana (4): examples: add arp cache dump example examples: fix neigh max attributes examples: fix print line format examples: reduce LOCs during neigh attributes validation Pablo Neira Ayuso (3): doxygen: remove EXPORT_SYMBOL from the output include: add MNL_SOCKET_DUMP_SIZE definition build: libmnl 1.0.5 release Petr Vorel (1): examples: Add rtnl-addr-add.c Stephen Hemminger (1): examples: rtnl-addr-dump: fix typo igo95862 (1): doxygen: Fixed link to the git source tree on the website. Signed-off-by: Nick Hainke <vincent@systemli.org> (cherry picked from commit c3b738933981de601389794152534628b04555dc)
* libnfnetlink: update to 1.0.2Nick Hainke2022-04-102-23/+3
| | | | | | | | | | | | | | | | | | | | | | | | Changes: c63f193 bump version to 1.0.2 3cffa84 libnfnetlink: Check getsockname() return code 90ba679 include: Silence gcc warning in linux_list.h bb4f6c8 Make it clear that this library is deprecated e46569c Minimally resurrect doxygen documentation 5087de4 libnfnetlink: hide private symbols 62ca426 autogen: don't convert __u16 to u_int16_t efa1d8e src: Use stdint types everywhere 7a1a07c include: Sync with kernel headers 7633f0c libnfnetlink: initialize attribute padding to resolve valgrind warnings 94b68f3 configure: uclinux is also linux 617fe82 src: get source code license header in sync with current licensing terms 97a3960 build: resolve automake-1.12 warnings Removed the patch 100-missing_include.patch, libnfnetlink compiles fine with musl without this patch. Signed-off-by: Nick Hainke <vincent@systemli.org> (cherry picked from commit aecf088b3792d556c717510304729fa542ceb770)
* gpio-button-hotplug: fix data raceAndrey Erokhin2022-04-101-1/+1
| | | | | | | | bh_event_add_var can be called by multiple threads concurrently, so it shall not use a static char buffer Signed-off-by: Andrey Erokhin <a.erokhin@inango-systems.com> (cherry picked from commit 1e991e09b73c309321d21b9cb706bd5139d952d2)
* libselinux: add missing host-build dependency on libsepol/hostDaniel Golle2022-04-101-1/+1
| | | | | | | | | The host-build of libselinux requires libsepol/host. Add the libsepol/host to HOST_BUILD_DEPENDS to allow build on hosts which don't have libsepol installed. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 0d3850dc5af4896ab3679dc4d8ef9a664e5e705f)
* dnsmasq: add procd interface index trackingValentyn Datsko2022-04-101-0/+5
| | | | | | | | | | | | | | Problem exist when dnsmasq is exclusively bind to particular interface. After reconfiguring or restarting this interface, its index changes, but dnsmasq uses the old one. When this problem occurs, dnsmasq does not listen on the correct interface so DHCP does not work, and clients do not get an IP address. Procd netdev param can be added to restart dnsmasq when the interface index is changed. Signed-off-by: Valentyn Datsko <valikk.d@gmail.com> [combined into a single &&-connected statement] Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 76f55e3c3f32dea63a385e9b3c8eaed1322089c7)
* libselinux: use musl-fts for host buildsRosen Penev2022-04-101-2/+5
| | | | | | | | | Fixes compilation under musl based distros like Alpine Linux. Also add pcre/host as a build dependency as it's needed. Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit abb2683de36ffe7b29a1b6ea5a8d7edf73719152)
* toolchain: reproducible libstdcppPaul Spooren2022-04-061-1/+2
| | | | | | | | A Python script containing an unreproducible path is copied by default. Remove it before generating the package. Signed-off-by: Paul Spooren <mail@aparcar.org> (cherry picked from commit 950bd40a275d1a834c95d8f9830e1bfed4737a82)
* grub2: add missing licensePaul Spooren2022-04-051-1/+3
| | | | | | | | The PKG_LICENSE field was missing. While at it, normalize the Makefile a bit. Signed-off-by: Paul Spooren <mail@aparcar.org> (cherry picked from commit 839b1ff1fc0d6bcd74131a78fb9286df7f3b7b97)
* kernel: load device-mapper early on bootDaniel Golle2022-04-051-1/+1
| | | | | | | | | | Previously commit openwrt/packages@3abb7cb ("lvm2: Added script and updated Makefile[...]") couldn't actually work and allow rootfs_data to be stored on a LVM2 as the necessary kernel modules had not been loaded at this point. Fix this by loading device-mapper modules early at boot. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 82f9ad6ab21ca4925278429a3e1b31d26c306d9f)
* kernel: modules: drop 'AddDepends/bluetooth' callsPiotr Dymacz2022-04-051-2/+0
| | | | | | | Function 'AddDepends/bluetooth' doesn't exist in our codebase. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> (cherry picked from commit 173198e35a898ff7ec97749247f75cd82fa3c3ab)
* busybox: Fix snprintf arguments in lockHauke Mehrtens2022-04-051-1/+1
| | | | | | | | | | The first argument for snprintf is the buffer and the 2. one is the size. Fix the order. This broke the lock application. Fixes: 9d2b26d5a705 ("busybox: fix busybox lock applet pidstr buffer overflow") Reported-by: Hartmut Birr <e9hack@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit d80336e1a970b088c235dcf2773052537e6f5d72)
* busybox: fix busybox lock applet pidstr buffer overflowQichao Zhang2022-04-051-3/+3
| | | | | | | | | | | Kernel setting `/proc/sys/kernel/pid_max` can be set up to 4194304 (7 digits) which will cause buffer overflow in busbox lock patch, this often happens when running in a rootfs container environment. This commit enlarges `pidstr` to 12 bytes to ensure a sufficient buffer for pid number and an additional char '\n'. Signed-off-by: Qichao Zhang <njuzhangqichao@gmail.com> (cherry picked from commit 34567750db2c3a84fc9f971189c223e2eefd93b0)
* pcre: disable shared libraries for host buildsRosen Penev2022-04-051-0/+1
| | | | | | | | | Getting rid of shared libraries for hostpkg avoids having to use rpath hacks to find the library. It also fixes compilation with host glib2 binaries. Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit f8571749a77ea23b418c84692220083858c1df79)
* musl-fts: remove shared libraries from hostRosen Penev2022-04-051-0/+1
| | | | | | | | | Avoids having to add rpath to the various packages using it. Also add PIC to fix compilation as static libraries do not use PIC by default. Fixes: 1fb099341e58 ("musl-fts: add host build") Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit 8a75ed4ba07b9d64ae547ce36873e51ba54f0eaf)
* gettext-full: add gmsgfmt symlink in host installStijn Tintel2022-04-051-0/+5
| | | | | | | | | | | | | | | Some configure scripts look for msgfmt and gmsgfmt. As we don't install the latter, configure might pick up one from staging_dir/hostpkg, and the other from the host: checking for msgfmt... /home/stijn/Development/OpenWrt/openwrt/staging_dir/hostpkg/bin/msgfmt checking for gmsgfmt... /usr/bin/gmsgfmt This could potentially lead to hard to debug undefined behaviour. Install a symlink in the host install phase to avoid this. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry picked from commit 636cb00ecc8d693c36e48952f6d154f91e0e569e)
* uboot-mvebu: backport patch to fix eMMCRobert Marko2022-04-051-0/+64
| | | | | | | | | | | v2022.01 has a regression that broke eMMC usage on most if not all Armada SoC-s, thus breaking boards like uDPU which use eMMC for storage. Fix it by backporting a recent upstream patch. Fixes: 782d4c8306c8 ("uboot-mvebu: update to version 2022.01") Signed-off-by: Robert Marko <robert.marko@sartura.hr> (cherry picked from commit a70383080694f26d13db8341a83261f6b1c45f12)
* uqmi: fix acquiring PIN statusDaniel Golle2022-03-271-4/+8
| | | | | | | | | | | | | Evaluating the return value of 'json_load' didn't work in the intended way resulting in PIN status no longer being read on modems where --get-pin-status doesn't fail. Fix this by trying --get-pin-status first and checking if pin1_status field exists in JSON, and if it doesn't try again with --uim-get-sim-state. Fixes: #9501 Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit ee7cb5e885118b78fb5f692d8ed6c93bb7e35853)
* mac80211: backport patch that allows receiving packets with non-standard VHT ↵Felix Fietkau2022-03-271-0/+36
| | | | | | | MCS10-11 rates Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry picked from commit 56ae4eb90864373dd4663f579851290be74430aa)
* uboot-mediatek: add patch to allow accessing bootconf from LinuxDaniel Golle2022-03-271-0/+60
| | | | | | | | | Store selected boot configuration in '/chosen' node in device tree, so it can be accessed by Linux (and used for fine-tuning the FIT partition parser). Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit dfc3ea6810904f4f498d4a1304443c1a4c9f1e3c)
* uboot-envtools: oxnas: fix wrong eraseblock size for shuttle,kd20Daniel Golle2022-03-271-1/+1
| | | | | | | | | Shuttle KD20 has NAND flash with 0x20000 (128KiB) erase blocks. Correctly set that in uboot-envtools as well to allow writing to the bootloader environment using fw_setenv. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit fa676395136b17d753fd90137e58f02a4fcdb09e)
* openwrt-keyring: fix broken install stepPetr Štetiar2022-03-271-0/+1
| | | | | | | | | | In commit 2d03f27f0f07 ("openwrt-keyring: make opkg use 22.03 usign key") I've accidentally removed the `endef` keyword, so fix it by adding it back. Fixes: 2d03f27f0f07 ("openwrt-keyring: make opkg use 22.03 usign key") Reported-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* openwrt-keyring: make opkg use 22.03 usign keyPetr Štetiar2022-03-271-4/+3
| | | | | | | | | | | | In order to make opkg usable with artifacts produced by project's buildbot: Downloading https://downloads.openwrt.org/releases/22.03-SNAPSHOT/packages/x86_64/luci/Packages.sig Signature check failed. Remove wrong Signature file. References: https://gitlab.com/openwrt/docker/-/jobs/2255191689 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: update E2600AC c1/c2 board张 鹏2022-03-263-2/+4
| | | | | | | | | | Modified the radio frequency hardware part of e2600ac c1/c2, need to cooperate with the modified board.bin file, the device can work normally. Signed-off-by: 张 鹏 <sd20@qxwlan.com> (cherry picked from commit bdc786e82c13547b01bd8f699d00598a974c14f6) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* cypress-firmware: drop several packagesJosef Schlehofer2022-03-261-54/+0
| | | | | | | | | | | | | | | | | | | | | | | | 1. Drop package: cypress-firmware-4359-pcie This binary is no longer provided and there are not many details what happened. 2. Drop package: cypress-firmware-4359-sdio This binary is no longer provided, but in this case, to compare it with PCIe package mention as first, there was added support in Linux-firmware [1], but no sign of firmware file. 4. Drop package: cypress-firmware-89459-pcie [2] According to Infineon: "CYW89459 is an automotive Wi-Fi chip which is not supported in the broad market community." [1] https://patchwork.kernel.org/project/linux-wireless/patch/20191211235253.2539-6-smoch@web.de/ [2] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/the-wifi-driver-for-CYW89459-in-linux4-14-98-2-3-00/m-p/138971 Fixes: 7ca7e0b22de6 ("cypress-firmware: update it to version 5.4.18-2021_0812") Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (cherry picked from commit 51dee3f4f7bac26cae8a6355f5a9adb4823f63a5)
* openwrt-keyring: add OpenWrt 22.03 GPG/usign keysPetr Štetiar2022-03-251-3/+3
| | | | | | | | 62471e693b4f usign: add 22.03 release build public key 70817cffc905 gpg: add OpenWrt 22.03 signing key Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 759886345d900139f38bd9200a32ce12868d3343)
* zlib: backport security fix for a reproducible crash in compressorPetr Štetiar2022-03-242-1/+344
| | | | | | | | | | | | | | | Tavis has just reported, that he was recently trying to track down a reproducible crash in a compressor. Believe it or not, it really was a bug in zlib-1.2.11 when compressing (not decompressing!) certain inputs. Tavis has reported it upstream, but it turns out the issue has been public since 2018, but the patch never made it into a release. As far as he knows, nobody ever assigned it a CVE. Suggested-by: Tavis Ormandy <taviso@gmail.com> References: https://www.openwall.com/lists/oss-security/2022/03/24/1 Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit b3aa2909a79aeff20d594160b207a89dc807c033)
* qosify: update to the latest versionFelix Fietkau2022-03-221-3/+3
| | | | | | | | | | | | | | | | | 391a9fbd5ace dns: fix parsing vlan encapsulated protocol 6aeeddbc91ad interface: extend dns filters to cover vlan tagged traffic as well 1ab53d4ca601 bpf: return TC_ACT_UNSPEC to allow other filters to proceed ca21e729af23 interface: switch to using clsact for filters 5d158f6b3c15 interface: run ingress bpf filter on main device ingress instead of ifb egress bdfcb11847ce interface: fix duplicated dns filter line b97405aa632a Revert "ubus: remove dnsmasq subscriber" 8fbaf39dbc95 interface: rework adding/removing filters, do not delete clsact d7ba5804eae4 interface: replace open-coded ifb-dns string with QOSIFY_DNS_IFNAME 91cf440db9e2 loader: fix use of deprecated functions 57c7817f91c2 qosify: fix dscp values of ubus-added dns host entries Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit af434e0da2485bd7a82895b5bb63b1182154b98e)
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 01:10:38 +0000