aboutsummaryrefslogtreecommitdiffstats
path: root/package
Commit message (Collapse)AuthorAgeFilesLines
* ath79: Add support for OpenMesh OM5PSven Eckelmann2020-12-302-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9344 rev 2 * 560/450/225 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 5 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + builtin switch port 1 + used as LAN interface - eth1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas WAN/LAN LEDs appear to be wrong in ar71xx and have been swapped here. Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org> [add LED swap comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for OpenMesh OM2P v2Sven Eckelmann2020-12-302-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9330 rev 1 * 400/400/200 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + builtin switch port 1 + used as LAN interface - eth1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * external antenna Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh OM2P-LCSven Eckelmann2020-12-302-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9330 rev 1 * 400/400/200 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + builtin switch port 1 + used as LAN interface - eth1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* odhcp6c: update to git HEADHans Dedecker2020-12-301-3/+3
| | | | | | | eac1961 dhcpv6: fix displaying IA info 0475e18 dhcpv6: display status code as a string Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* base-files: sysupgrade: add function for conffiles retrievalAdrian Schmutzler2020-12-302-8/+13
| | | | | | | | | | | | The find command to retrieve files from /etc/sysupgrade.conf and /lib/upgrade/keep.d/* is used twice in almost the same way. Move it into a function to consolidate, enhance readability and make future adjustments easier. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org> Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
* busybox: define BUSYBOX_SYM before the first useMaxim Storchak2020-12-291-4/+4
| | | | | | Since PKG_FILE_MODES relies on BUSYBOX_SYM, it should be defined early enough Signed-off-by: Maxim Storchak <m.storchak@gmail.com>
* ath79: add support for OpenMesh OM2P-HS v3Sven Eckelmann2020-12-292-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9341 rev 1 * 535/400/200 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 802.3af POE + builtin switch port 1 + used as LAN interface - eth1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: add support for OpenMesh OM2P-HS v2Sven Eckelmann2020-12-292-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9341 rev 1 * 535/400/200 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 802.3af POE + builtin switch port 1 + used as LAN interface - eth1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: add support for OpenMesh OM2P-HS v1Sven Eckelmann2020-12-292-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9341 rev 1 * 535/400/200 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 802.3af POE + builtin switch port 1 + used as LAN interface - eth1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org> [drop redundant status from eth1] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx-cfe: update to the latest masterRafał Miłecki2020-12-281-4/+4
| | | | | | | | | | c0b3691 netgear: r8000p: add cferam file ae870eb asus: gt-ac5300: add cferam file 424b57c sfr: neufbox-6v-foxconn-r0: update cferam file 81a2a8b sfr: neufbox-6v-foxconn-r0: add cferam file 2730361 sercomm: h500-s: add cferam file Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: Add support for OpenMesh OM2P-HS v4Sven Eckelmann2020-12-282-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9533 v2 * 650/600/217 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 24V passive POE (mode B) + used as WAN interface - eth1 + 802.3af POE + builtin switch port 1 + used as LAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh OM2P v4Sven Eckelmann2020-12-282-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9533 v2 * 650/600/217 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + Label: Ethernet 1 + 24V passive POE (mode B) - eth1 + Label: Ethernet 2 + 802.3af POE + builtin switch port 1 * 12-24V 1A DC * external antenna Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org> [wrap two very long lines, fix typo in comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath10k-ct-firmware: update to 022 (2020-11-08)Álvaro Fernández Rojas2020-12-281-34/+34
| | | | | | Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath10k-ct: update to latest versionÁlvaro Fernández Rojas2020-12-284-13/+13
| | | | | | | | | Changelog: - ath10k-ct: Fix invalid use of ath-cb struct Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ethtool: update to version 5.10Hans Dedecker2020-12-261-2/+2
| | | | | | | | The ipkg sizes changes as follows for mips 24kc : 5.9 : ethtool_5.9-1_mips_24kc.ipk 35246 5.10 : ethtool_5.10-1_mips_24kc.ipk 35385 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kmod-tcp-hybla: new module for hybla congestion control algorithmYousong Zhou2020-12-261-0/+18
| | | | | | | Just the module and no default sysctl conf file is provided Link: https://forum.openwrt.org/t/20-xx-tcp-hybla/83076 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* kmod-tcp-bbr: use AutoProbeYousong Zhou2020-12-261-1/+1
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* kmod-tcp-bbr: leave CONFIG_TCP_CONG_ADVANCED to target configYousong Zhou2020-12-261-3/+1
| | | | | | | Since generic has the option set to y and other targets now inherit that choice, there is no behaviour change Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ipq40xx: add support for GL.iNet GL-AP1300Dongming Han2020-12-253-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: Reset LED: Power, Internet UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 OTHER: On board with BLE module - by cp210x USB serial chip On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi (IPQ40xx) # run lf By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq806x: add support for NEC Platforms Aterm WG2600HP3Yanase Yuki2020-12-252-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Platforms Aterm WG2600HP3 is a dual-band router based on Qualcomm IPQ8062. Specification ------------- - SoC: Qualcomm IPQ8062 - RAM: 512MiB - Flash memory: SPI-NOR 32MiB (Cypress S25FL256S) - Wi-Fi: Qualcomm QCA9984 (2.4GHz, 1ch - 13ch) - Wi-Fi: Qualcomm QCA9984 (5GHz, 36ch - 64ch, 100ch - 140ch) - Ethernet: 4x 100/1000 Mbps (1x WAN, 4x LAN) - LED: 6x green LED, 6x red LED - Input: 2x tactile switch, 1x SP3T slide switch - Serial console: 115200bps, through-hole J3 - [ ] [GND] [ ] [TX] [RX] ----> DC jack - Power: DC 12V 1.5A This device does not support VHT160 and VHT80+80. Custom BDFs are required to limit VHT capabilities. Flash instructions ------------------ 1. Setup TFTP server (IP address: 192.168.1.2) 2. Put initramfs image into TFTP server directory 3. Connect WG2600HP3 lan port and computer that runs TFTP server 4. Connect to the serial console 5. Interrupt booting by Esc key (password: chiron) 6. Execute the following commands # setenv bootcmd "nboot 0x44000000 1 0x860000" # saveenv # setenv ipaddr 192.168.1.1 # setenv serverip 192.168.1.2 # tftpboot 0x44000000 openwrt-ipq806x-generic-nec_wg2600hp3-initramfs-uImage 7. After booting OpenWrt initramfs image, backup SPI-NOR flash memory 8. Erase firmware partition # mtd erase firmware 9. Run sysupgrade Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* ipq-wifi: Fix suffix for Plasma Cloud PA2200 QCA4019 board-2.binSven Eckelmann2020-12-251-0/+0
| | | | | | | | | | | | | The Makefile is rejecting all files with for a given prefix (here "board-plasmacloud_pa2200") when it didn't match a known suffix. Instead it stops the build with an error like: Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa2200.ipq4019'. Stop. The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019. Fixes: 4871fd2616ac ("ipq40xx: add support for Plasma Cloud PA2200") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq-wifi: Fix suffix for Plasma Cloud PA1200 QCA4019 board-2.binSven Eckelmann2020-12-251-0/+0
| | | | | | | | | | | | | The Makefile is rejecting all files with for a given prefix (here "board-plasmacloud_pa1200") when it didn't match a known suffix. Instead it stops the build with an error like: Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa1200.ipq4019'. Stop. The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019. Fixes: ea5bb6bbfee0 ("ipq40xx: add support for Plasma Cloud PA1200") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: add support for Senao Engenius EAP350 v1Michael Pratt2020-12-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: U2M-EAP350 Engenius EAP350 is a wireless access point with 1 gigabit PoE ethernet port, 2.4 GHz wireless, external ethernet switch, and 2 internal antennas. Specification: - AR7242 SOC - AR9283 WLAN (2.4 GHz, 2x2, PCIe on-board) - AR8035-A switch (GbE with 802.3af PoE) - 40 MHz reference clock - 8 MB FLASH MX25L6406E - 32 MB RAM EM6AA160TSA-5G - UART at J2 (populated) - 3 LEDs, 1 button (power, eth, 2.4 GHz) (reset) - 2 internal antennas MAC addresses: MAC address is labeled as "MAC" Only 1 address on label and in flash The OEM software reports these MACs for the ifconfig eth0 MAC *:0c art 0x0 phy0 --- *:0d --- Installation: 2 ways to flash factory.bin from OEM: - if you get Failsafe Mode from failed flash: only use it to flash Original firmware from Engenius or risk kernel loop or halt which requires serial cable Method 1: Firmware upgrade page: OEM webpage at 192.168.10.1 username and password "admin" Navigate to "Upgrade Firmware" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9f670000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes Return to OEM: If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image *DISCLAIMER* The Failsafe image is unique to Engenius boards. If the failsafe image is missing or damaged this will not work DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade Format of OEM firmware image: The OEM software of EAP350 is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names... openwrt-senao-eap350-uImage-lzma.bin openwrt-senao-eap350-root.squashfs and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. The OEM upgrade script is at /etc/fwupgrade.sh Later models in the EAP series likely have a different platform and the upgrade and image verification process differs. OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1024k and the factory.bin upgrade procedure would overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035-A switch between the SOC and the ethernet PHY chips. For AR724x series, the PLL register for GMAC0 can be seen in the DTSI as 0x2c. Therefore the PLL register can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x1805002c 1`. uboot did not have a good value for 1 GBps so it was taken from other similar DTS file. Tested from master, all link speeds functional Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Senao Engenius EAP600Michael Pratt2020-12-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-EAP600 Engenius EAP600 is a wireless access point with 1 gigabit ethernet port, dual-band wireless, external ethernet switch, 4 internal antennas and 802.3af PoE. Specification: - AR9344 SOC (5 GHz, 2x2, WMAC) - AR9382 WLAN (2.4 GHz, 2x2, PCIe on-board) - AR8035-A switch (GbE with 802.3af PoE) - 40 MHz reference clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16DG - UART at H1 (populated) - 5 LEDs, 1 button (power, eth, 2.4 GHz, 5 GHz, wps) (reset) - 4 internal antennas MAC addresses: MAC addresses are labeled MAC1 and MAC2 The MAC address in flash is not on the label The OEM software reports these MACs for the ifconfig eth0 MAC 1 *:5e --- phy1 MAC 2 *:5f --- (2.4 GHz) phy0 ----- *:60 art 0x0 (5 GHz) Installation: 2 ways to flash factory.bin from OEM: - if you get Failsafe Mode from failed flash: only use it to flash Original firmware from Engenius or risk kernel loop or halt which requires serial cable Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Upgrade Firmware" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fdf0000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes Return to OEM: If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image *DISCLAIMER* The Failsafe image is unique to Engenius boards. If the failsafe image is missing or damaged this will not work DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade Format of OEM firmware image: The OEM software of EAP600 is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names... openwrt-senao-eap600-uImage-lzma.bin openwrt-senao-eap600-root.squashfs and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. The OEM upgrade script is at /etc/fwupgrade.sh Later models in the EAP series likely have a different platform and the upgrade and image verification process differs. OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035-A switch between the SOC and the ethernet PHY chips. For AR934x series, the PLL register for GMAC0 can be seen in the DTSI as 0x2c. Therefore the PLL register can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x1805002c 1`. Unfortunately uboot did not have the best values so they were taken from other similar DTS files. Tested from master, all link speeds functional Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Senao Engenius ECB600Michael Pratt2020-12-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-ECB600 Engenius ECB600 is a wireless access point with 1 gigabit PoE ethernet port, dual-band wireless, external ethernet switch, and 4 external antennas. Specification: - AR9344 SOC (5 GHz, 2x2, WMAC) - AR9382 WLAN (2.4 GHz, 2x2, PCIe on-board) - AR8035-A switch (GbE with 802.3af PoE) - 40 MHz reference clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16DG - UART at H1 (populated) - 4 LEDs, 1 button (power, eth, 2.4 GHz, 5 GHz) (reset) - 4 external antennas MAC addresses: MAC addresses are labeled MAC1 and MAC2 The MAC address in flash is not on the label The OEM software reports these MACs for the ifconfig phy1 MAC 1 *:52 --- (2.4 GHz) phy0 MAC 2 *:53 --- (5 GHz) eth0 ----- *:54 art 0x0 Installation: 2 ways to flash factory.bin from OEM: - if you get Failsafe Mode from failed flash: only use it to flash Original firmware from Engenius or risk kernel loop or halt which requires serial cable Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Upgrade Firmware" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fdf0000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes Return to OEM: If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image *DISCLAIMER* The Failsafe image is unique to Engenius boards. If the failsafe image is missing or damaged this will not work DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade Format of OEM firmware image: The OEM software of ECB600 is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names... openwrt-senao-ecb600-uImage-lzma.bin openwrt-senao-ecb600-root.squashfs and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. The OEM upgrade script is at /etc/fwupgrade.sh Later models in the ECB series likely have a different platform and the upgrade and image verification process differs. OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035-A switch between the SOC and the ethernet PHY chips. For AR934x series, the PLL register for GMAC0 can be seen in the DTSI as 0x2c. Therefore the PLL register can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x1805002c 1`. Unfortunately uboot did not have the best values so they were taken from other similar DTS files. Tested from master, all link speeds functional Signed-off-by: Michael Pratt <mcpratt@pm.me>
* odhcpd: update to latest git HEADHans Dedecker2020-12-241-3/+3
| | | | | | | | b75bcad dhcpv6-ia: remove assignment equal to 0 checks d1ae052 dhcpv6-ia: fix logic to include IA_PD prefix with lifetimes set to 0 9d5e379 dhcpv6-ia: fix prefix delegation behavior Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* opkg: update to git HEADDaniel Golle2020-12-241-3/+3
| | | | | | 9bbc7ea pkg_hash: pkg_hash_check_unresolved: fix segfault Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* treewide: nuke DRIVER_11W_SUPPORTDobroslaw Kijowski2020-12-2312-33/+23
| | | | | | | | | | | | | | As of hostapd upstream commit 7d2ed8ba "Remove CONFIG_IEEE80211W build parameter" https://w1.fi/cgit/hostap/commit?id=7d2ed8bae86a31dd2df45c24b3f7281d55315482 802.11w feature is always enabled in the build time. It doesn't make sense to opt-in 802.11w per driver as hostapd will always be compiled with this feature enabled. As suggested by Hauke Mehrtens, for now keep 11w enabled in build_features.h for compatibility reasons. This option will be dropped when LuCI is adjusted. Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
* netifd: update to the latest versionFelix Fietkau2020-12-231-3/+3
| | | | | | 88c6003e2b4f netifd: fix a typo in vlandev hotplug support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* base-files: drop banner.failsafe if failsafe is disabledPiotr Dymacz2020-12-221-1/+4
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: add support for devolo Magic 2 WiFi nextStefan Schake2020-12-223-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8075 (2 ports) PLC: MaxLinear G.hn 88LX5152 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET, WiFi, PLC Button LEDS: red/white home, white WiFi To modify a retail device to run OpenWRT firmware: 1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'. 2) Power on the device while pressing the recessed reset button next to the Ethernet ports. This causes the bootloader to retrieve and start the initramfs. 3) Once the initramfs is booted, the device will come up with IP 192.168.1.1. You can then connect through SSH (allow some time for the first connection). 4) On the device shell, run 'fw_printenv' to show the U-boot environment. Backup this information since it contains device unique factory data. 5) Change the boot command to support booting OpenWRT: # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm' 6) Change directory to /tmp, download the sysupgrade (e.g. through wget) and install it with sysupgrade. The device will reboot into OpenWRT. Notice that there is currently no support for booting the G.hn chip. This requires userland software we lack the rights to share right now. Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
* hostapd: pass respawn settings when registering the serviceJohn Crispin2020-12-221-2/+2
| | | | | | | | When hostapd gets restarted to often/quickly will cause procd to not restart it anymore. it will think that hapd is in a crash loop. Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> [adjust respawn time]
* kirkwood: add support for Seagate BlackArmor NAS220Kip Porterfield2020-12-222-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Seagate BlackArmor NAS220 is a consumer NAS with two internal drive bays. The stock OS runs RAID 1 over the disks via mdadm. Device specification: - SoC: Marvell 88F6192 800 MHz - RAM: 128 MB - Flash: 32 MB - 2 x internal SATA II drives - Ethernet: 10/100/1000 Mbps (single port, no switch) - WLAN: None - LED: Power, Status, Sata Activity - Key: Power, Reset - Serial: 10 pin header, (115200,8,N,1), 3.3V TTL 9|x - x|10 7|x - x|8 5|x - GND|6 3|x - RX|4 1|TX - x|2 front of case - USB ports: 2 x USB 2.0 Flash instruction: NOTE: this process uses a serial connection. It will upgrade the bootloader and reset the bootloader environment variables TFTP server setup - Setup PC with TFTP server set the PC IP to 10.4.50.5 as TFTP server - Copy these files to TFTP server location - u-boot.kwb - seagate_blackarmor-nas220-initramfs-uImage - seagate_blackarmor-nas220-squashfs-sysupgrade.bin - seagate_blackarmor-nas220-squashfs-factory.bin Seagate NAS setup - Connect LAN cable between PC and seagate device - Connect to serial to seagate device Install u-boot - Boot seagate device and stop in bootloader by pressing any key - run 'printenv' from u-boot and save the values - tftpboot 0x2000000 u-boot.kwb - nand erase.part uboot - nand write 0x2000000 0x0 ${filesize} - reset Update MAC address in u-boot env - Stop in u-boot by pressing any key - Get your MAC address from your saved printenv. Is also on chassis - setenv ethaddr <your MAC> - saveenv Option 1 (recommended) - Install OpenWrt via initramfs and sysupgrade - tftpboot 0x2000000 seagate_blackarmor-nas220-initramfs-uImage - bootm 0x2000000 - *OpenWrt should be running now, however it is not written to flash yet* - From the running instance of OpenWrt use Luci's "flash image" feature from the web site or use sysupgrade from the console to write seagate_blackarmor-nas220-squashfs-sysupgrade.bin to flash Option 2 - Install OpenWrt by flashing factory image from u-boot - nand erase.part ubi - tftpboot 0x2000000 seagate_blackarmor-nas220-squashfs-factory.bin - nand write 0x2000000 ubi ${filesize} - reset Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
* ath79: add support for Senao Engenius EnStationAC v1Michael Pratt2020-12-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-ENSTAC Engenius EnStationAC v1 is an outdoor wireless access point/bridge with 2 gigabit ethernet ports on 2 external ethernet switches, 5 GHz only wireless, internal antenna plates, and proprietery PoE. Specification: - QCA9557 SOC - QCA9882 WLAN (PCI card, 5 GHz, 2x2, 26dBm) - AR8035-A switch (RGMII GbE with PoE+ IN) - AR8031 switch (SGMII GbE with PoE OUT) - 40 MHz reference clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16FG - UART at J10 (unpopulated) - internal antenna plates (19 dbi, directional) - 7 LEDs, 1 button (power, eth, wlan, RSSI) (reset) MAC addresses: MAC addresses are labeled as ETH and 5GHz Vendor MAC addresses in flash are duplicate eth0 ETH *:d3 art 0x0/0x6 eth1 ---- *:d4 --- phy0 5GHz *:d5 --- Installation: 2 ways to flash factory.bin from OEM: - if you get Failsafe Mode from failed flash: only use it to flash Original firmware from Engenius or risk kernel loop or halt which requires serial cable Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Firmware" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes Return to OEM: If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image *DISCLAIMER* The Failsafe image is unique to Engenius boards. If the failsafe image is missing or damaged this will not work DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade TFTP recovery: rename initramfs to 'vmlinux-art-ramdisk' make available on TFTP server at 192.168.1.101 power board hold or press reset button repeatedly NOTE: for some Engenius boards TFTP is not reliable try setting MTU to 600 and try many times Format of OEM firmware image: The OEM software of EnStationAC is a heavily modified version of Openwrt Altitude Adjustment 12.09. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names... openwrt-ar71xx-enstationac-uImage-lzma.bin openwrt-ar71xx-enstationac-root.squashfs and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. Newer EnGenius software requires more checks but their script includes a way to skip them, otherwise the tar must include a text file with the version and md5sums in a deprecated format. The OEM upgrade script is at /etc/fwupgrade.sh. OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8033 switch between the SOC and the ethernet PHY chips. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. For eth0 at 1000 speed, the value returned was ae000000 but that didn't work, so following the logical pattern from the rest of the values, the guessed value of a3000000 works better. later discovered that delay can be placed on the PHY end only with phy-mode as 'rgmii-id' and set register to 0x82... Tested from master, all link speeds functional Signed-off-by: Michael Pratt <mcpratt@pm.me> [fixed SoB to match From:] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: add support for Plasma Cloud PA2200Marek Lindner2020-12-224-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200 * GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE * GPIO-LEDs for power (orange) and status (blue) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3at POE+ + used as WAN interface * 12V 2A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: add support for Plasma Cloud PA1200Marek Lindner2020-12-223-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4018 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200 * 3x GPIO-LEDs for status (cyan, purple, yellow) * 1x GPIO-button (reset) * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio4: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio3: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3af/at POE(+) + used as WAN interface * 12V/24V 1A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for Plasma Cloud PA300ESven Eckelmann2020-12-221-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * Qualcomm/Atheros QCA9533 v2 * 650/600/217 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash (mx25l12805d) - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 2.4 GHz Wi-Fi * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + Label: Ethernet 1 + 24V passive POE (mode B) + used as WAN interface - eth1 + Label: Ethernet 2 + 802.3af POE + builtin switch port 2 + used as LAN interface * 12-24V 1A DC * external antennas Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for Plasma Cloud PA300Sven Eckelmann2020-12-221-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * Qualcomm/Atheros QCA9533 v2 * 650/600/217 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash (mx25l12805d) - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 2.4 GHz Wi-Fi * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + Label: Ethernet 1 + 24V passive POE (mode B) + used as WAN interface - eth1 + Label: Ethernet 2 + 802.3af POE + builtin switch port 2 + used as LAN interface * 12-24V 1A DC * internal antennas Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: add support for Senao Engenius ECB350 v1Michael Pratt2020-12-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-ECB350 Engenius ECB350 v1 is an indoor wireless access point with a gigabit ethernet port, 2.4 GHz wireless, external antennas, and PoE. **Specification:** - AR7242 SOC - AR9283 WLAN 2.4 GHz (2x2), PCIe on-board - AR8035-A switch RGMII, GbE with 802.3af PoE - 40 MHz reference clock - 8 MB FLASH 25L6406EM2I-12G - 32 MB RAM - UART at J2 (populated) - 2 external antennas - 3 LEDs, 1 button (power, lan, wlan) (reset) **MAC addresses:** MACs are labeled as WLAN and WAN vendor MAC addresses in flash are duplicate phy0 WLAN *:b8 --- eth0 WAN *:b9 art 0x0/0x6 **Installation:** - if you get Failsafe Mode from failed flash: only use it to flash Original firmware from Engenius or risk kernel loop or halt which requires serial cable Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Firmware" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9f670000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image *DISCLAIMER* The Failsafe image is unique to Engenius boards. If the failsafe image is missing or damaged this will not work DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade **TFTP recovery** (unstable / not reliable): rename initramfs to 'vmlinux-art-ramdisk' make available on TFTP server at 192.168.1.101 power board while holding or pressing reset button repeatedly NOTE: for some Engenius boards TFTP is not reliable try setting MTU to 600 and try many times **Format of OEM firmware image:** The OEM software of ECB350 v1 is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. The OEM upgrade script is at /etc/fwupgrade.sh. OKLI kernel loader is required because the OEM software expects the kernel size to be no greater than 1536k and otherwise the factory.bin upgrade procedure would overwrite part of the kernel when writing rootfs. The factory upgrade script follows the original mtd partitions. **Note on PLL-data cells:** The default PLL register values will not work because of the AR8035 switch between the SOC and the ethernet port. For AR724x series, the PLL register for GMAC0 can be seen in the DTSI as 0x2c. Therefore the PLL register can be read from u-boot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x1805002c 1` However the registers that u-boot sets are not ideal and sometimes wrong... the at803x driver supports setting the RGMII clock/data delay on the PHY side. This way the pll-data register only needs to handle invert and phase. for this board no extra adjustements are needed on the MAC side all link speeds functional Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Senao Engenius ECB1200Michael Pratt2020-12-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-ECB1200 Engenius ECB1200 is an indoor wireless access point with a GbE port, 2.4 GHz and 5 GHz wireless, external antennas, and 802.3af PoE. **Specification:** - QCA9557 SOC MIPS, 2.4 GHz (2x2) - QCA9882 WLAN PCIe card, 5 GHz (2x2) - AR8035-A switch RGMII, GbE with 802.3af PoE, 25 MHz clock - 40 MHz reference clock - 16 MB FLASH 25L12845EMI-10G - 2x 64 MB RAM 1538ZFZ V59C1512164QEJ25 - UART at JP1 (unpopulated, RX shorted to ground) - 4 external antennas - 4 LEDs, 1 button (power, eth, wifi2g, wifi5g) (reset) **MAC addresses:** MAC Addresses are labeled as ETH and 5GHZ U-boot environment has the vendor MAC addresses MAC addresses in ART do not match vendor eth0 ETH *:5c u-boot-env ethaddr phy0 5GHZ *:5d u-boot-env athaddr ---- ---- ???? art 0x0/0x6 **Installation:** Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Firmware" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly (see TFTP recovery) perform a sysupgrade **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART pinout at JP1 **Return to OEM:** If you have a serial cable, see Serial Failsafe instructions Unlike most Engenius boards, this does not have a 'failsafe' image the only way to return to OEM is TFTP or serial access to u-boot **TFTP recovery:** Unlike most Engenius boards, TFTP is reliable here rename initramfs-kernel.bin to 'ap.bin' make the file available on a TFTP server at 192.168.1.10 power board while holding or pressing reset button repeatedly or with serial access: run `tftpboot` or `run factory_boot` with initramfs-kernel.bin then `bootm` with the load address **Format of OEM firmware image:** The OEM software of ECB1200 is a heavily modified version of Openwrt Altitude Adjustment 12.09. This Engenius board, like ECB1750, uses a proprietary header with a unique Product ID. The header for factory.bin is generated by the mksenaofw program included in openwrt. **Note on PLL-data cells:** The default PLL register values will not work because of the AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. However the registers that u-boot sets are not ideal and sometimes wrong... the at803x driver supports setting the RGMII clock/data delay on the PHY side. This way the pll-data register only needs to handle invert and phase. for this board clock invert is needed on the MAC side all link speeds functional Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: add support for Senao Engenius ESR600HMichael Pratt2020-12-221-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-ESR750H Engenius ESR600H is an indoor wireless router with a gigabit switch, 2.4 GHz and 5 GHz wireless, internal and external antennas, and a USB port. **Specification:** - RT3662F MIPS SOC, 5 GHz WMAC (2x2) - RT5392L PCI on-board, 2.4 GHz (2x2) - AR8327 RGMII, 7-port GbE, 25 MHz clock - 40 MHz reference clock - 8 MB FLASH 25L6406EM2I-12G - 64 MB RAM - UART at J12 (unpopulated) - 2 internal antennas (5 GHz) - 2 external antennas (2.4 GHz) - 9 LEDs, 1 button (power, wps, wifi2g, wifi5g, 5 LAN/WAN) - USB 2 port (GPIO controlled power) **MAC addresses:** MAC Addresses are labeled as WAN and WLAN U-boot environment has the the vendor MAC address for ethernet MAC addresses in "factory" are part of wifi calibration data eth0.2 WAN *:13:e7 u-boot-env wanaddr eth0.1 ---- *:13:e8 u-boot-env wanaddr + 1 phy0 WLAN *:14:b8 factory 0x8004 phy1 ---- *:14:bc factory 0x4 **Installation:** Method 1: Firmware upgrade page OEM webpage at 192.168.0.1 username and password "admin" Navigate to Network Setting --> Tools --> Firmware Click Browse and select the factory.dlf image Click Continue to confirm and wait 6 minutes or more... Method 2: Serial console to load TFTP image: (see TFTP recovery) **Return to OEM:** Unlike most Engenius boards, this does not have a 'failsafe' image the only way to return to OEM is serial access to uboot Unlike most Engenius boards, public images are not available... so the only way to return to OEM is to have a copy of the MTD partition "firmware" BEFORE flashing openwrt. **TFTP recovery:** Unlike most Engenius boards, TFTP is reliable here however it requires serial console access (soldering pins to the UART pinouts) build your own image... with 'ramdisk' selected under 'Target Images' rename initramfs-kernel.bin to 'uImageESR-600H' make the file available on a TFTP server at 192.168.99.8 interrupt boot by holding or pressing '4' in serial console as soon as board is powered on `tftpboot 0x81000000` `bootm 0x81000000` perform a sysupgrade **Format of OEM firmware image:** This Engenius board uses the Senao proprietary header with a unique Product ID. The header for factory.bin is generated by the mksenaofw program included in openwrt. .dlf file extension is also required for OEM software to accept it **Note on using OKLI:** the kernel is now too large for the bootloader to handle so OKLI is used via the `kernel-loader` image command recently in master several other ramips boards have the same problem 'Kernel panic - not syncing: Failed to find ralink,rt3883-sysc node' see commit ad19751edc21ae713bd95df6b93be64bd1e0c612 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* toolchain: remove uClibc install stuffRosen Penev2020-12-221-28/+3
| | | | | | This is preparation for removing uClibc-ng. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* hostapd: Use EAPOLv1 (802.1X-2001) if WPA enabledNick Lowe2020-12-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, EAPOLv2 (802.1X-2004) is used by default for legacy clients that are not WPA2 (RSN) capable. These legacy clients are often intolerant to this EAPOL version and fail to connect. hostapd.conf upstream documents for eapol_version the following and that this is a known compatibility issue with version 2: // IEEE 802.1X/EAPOL version // hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL // version 2. However, there are many client implementations that do not handle // the new version number correctly (they seem to drop the frames completely). // In order to make hostapd interoperate with these clients, the version number // can be set to the older version (1) with this configuration value. // Note: When using MACsec, eapol_version shall be set to 3, which is // defined in IEEE Std 802.1X-2010. //eapol_version=2 For the wpa parameter, hostapd.conf upstream documents that this is a bitfield, configured as follows: // Enable WPA. Setting this variable configures the AP to require WPA (either // WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either // wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK. // Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice. // For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys), // RADIUS authentication server must be configured, and WPA-EAP must be included // in wpa_key_mgmt. // This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0) // and/or WPA2 (full IEEE 802.11i/RSN): // bit0 = WPA // bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled) // Note that WPA3 is also configured with bit1 since it uses RSN just like WPA2. // In other words, for WPA3, wpa=2 is used the configuration (and // wpa_key_mgmt=SAE for WPA3-Personal instead of wpa_key_mgmt=WPA-PSK). //wpa=2 For client compatibility therefore: EAPOLv1 (802.1X-2001) should be used by default where WPA is enabled. EAPOLv2 (802.1X-2004) should be used by default where WPA is disabled. To fix this, we can therefore change in the script: set_default eapol_version 0 To the following: set_default eapol_version $((wpa & 1)) This therefore: 1) Sets eapol_version to 1 where WPA has been enabled via wpa bit0 being set. 2) Sets eapol_version to 0 where WPA has been disabled via wpa bit0 being unset. For usual configurations that only have WPA2 enabled, EAPOLv2 is then used. Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
* mac80211: fix MAC address allocations when local bit set on base addrPaul Fertser2020-12-221-2/+2
| | | | | | | | | | | | | | | Testing with hwsim reveals two problems: 1. phyX/addresses has two addresses and mac80211_get_addr keeps returning the last one when asked for more; 2. The base address has the local bit set and the operation unsets it. Fix both. Fixes: 866790fd827cb0187353cdf484eb46a9b38fb6ba Reported-by: Zero_Chaos Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* base-files: flush kernel memory cache during sysupgradeHannu Nyman2020-12-222-0/+2
| | | | | | | | | | | Flush kernel memory caches during sysupgrade in order to mitigate the impact from memory consumption spikes in low-RAM devices. This may help to prevent sysupgrade causing a reboot before the actual flashing starts. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* uboot-tegra: bump to 2020.04Tomasz Maciej Nowak2020-12-221-2/+2
| | | | | | | | | This fixes error when host GCC >= 10. /usr/bin/ld: scripts/dtc/dtc-parser.tab.o:(.bss+0x10): multiple definition of `yylloc'; scripts/dtc/dtc-lexer.lex.o:(.bss+0x0): first defined here collect2: error: ld returned 1 exit status Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* tcpdump: fix pcap-config issuesRosen Penev2020-12-222-115/+4
| | | | | | | | | | | | | | The patch removes a libpcap check to avoid a problem with libpcap. Fix libpcap instead. Modernize Makefile: Use a normal autoconf bool instead of checking for CONFIG_IPV6. Remove old configure and MAKE_FLAGS hacks. Removing them results in compilation continuing to work without a problem. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* libpcap: fix pcap-configRosen Penev2020-12-221-2/+10
| | | | | | | | | | | | | pcap-config as installed is using OS paths instead of OpenWrt ones. Take fix from libpng and adjust as needed. This problem seems to occur on Arch Linux and not on Debian/Fedora based distros. No idea why. Remove CMAKE_INSTALL as there is now an InstallDev section. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* fs/cifs: update module dependenciesRosen Penev2020-12-221-7/+10
| | | | | | | | | | | 0fdfef9aa7ee68ddd508aef7c98630cfc054f8d6 upstream removed CIFS_SMB311. Kernels 4.19 and above do not have it. Currently only kernels 4.19 and 5.4 are in the tree. The Kconfig file in the kernel has more selection that what is in here. Add the rest and reorder based on upstream ordering. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* pcre: fix paths in config fileRosen Penev2020-12-221-1/+2
| | | | | | | | | The paths are pointing to OS paths, not OpenWrt ones. Use SED line from libpng to fix and adjust accordingly. This may allow certain packages that use the config file to pick up pcre. Signed-off-by: Rosen Penev <rosenp@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-19 14:13:02 +0000