aboutsummaryrefslogtreecommitdiffstats
path: root/package
Commit message (Collapse)AuthorAgeFilesLines
* ipq-wifi: add board-2.bin for ASUS RT-AC58UMathias Kresin2018-03-151-0/+0
| | | | | | | The existing file is 0 byte. Replace the ASUS RT-AC58U board-2.bin with the correct file. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: add Cisco Meraki MR33 SupportChris Blake2018-03-142-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* base-files: add more name source to get_dt_led helper functionMathias Kresin2018-03-141-1/+4
| | | | | | | | Not all LED driver are using the label devicetree property for the led name. Add support for the TI/National Semiconductor LP55xx Led Drivers, which are using the chan-name property for the led name, as fallback. Signed-off-by: Mathias Kresin <dev@kresin.me>
* base-files: add function to get binary mac from fileMathias Kresin2018-03-141-6/+13
| | | | | | | Add a fucntion to get the a binary mac address from file. Use the new function for mtd_get_mac_binary() to limit duplicate code. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13Christian Lamparter2018-03-142-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for ASUS RT-AC58U/RT-ACRH13. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE) NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI) ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one Reset and one WPS button LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each) Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has an unpopulated 1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the PCB right next to the connector. U-Boot Note: The ethernet driver isn't always reliable and can sometime time out... Don't worry, just retry. Access via the serial console is required. As well as a working TFTP-server setup and the initramfs image. (If not provided, it has to be built from the OpenWrt source. Make sure to enable LZMA as the compression for the INITRAMFS!) To install the image permanently, you have to do the following steps in the listed order. 1. Open up the router. There are four phillips screws hiding behind the four plastic feets on the underside. 2. Connect the serial cable (See notes above) 3. Connect your router via one of the four LAN-ports (yellow) to a PC which can set the IP-Address and ssh and scp from. If possible set your PC's IPv4 Address to 192.168.1.70 (As this is the IP-Address the Router's bootloader expects for the tftp server) 4. power up the router and enter the u-boot choose option 1 to upload the initramfs image. And follow through the ipv4 setup. Wait for your router's status LED to stop blinking rapidly and glow just blue. (The LAN LED should also be glowing blue). 3. Connect to the OpenWrt running in RAM The default IPv4-Address of your router will be 192.168.1.1. 1. Copy over the openwrt-sysupgrade.bin image to your router's temporary directory # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp 2. ssh from your PC into your router as root. # ssh root@192.168.1.1 The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key. Once connected...: run the following commands on your temporary installation 3. delete the "jffs2" ubi partition to make room for your new root partition # ubirmvol /dev/ubi0 --name=jffs2 4. install OpenWrt on the NAND Flash. # sysupgrade -v /tmp/openwrt-sysupgrade.bin - This will will automatically reboot the router - Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mac80211: ath10k: search all IEs for variant before falling backChristian Lamparter2018-03-142-0/+237
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the patch that was posted to ath10k-devel ML: <https://patchwork.kernel.org/patch/10233491/> |From: Thomas Hebb <tommyhebb@gmail.com> |Subject: [PATCH] ath10k: search all IEs for variant before falling back |Date: Wed, 21 Feb 2018 11:43:39 -0500 |[...] |This patch fixes the issue by first searching the entire file for the ID |with variant, and searching for the fallback ID only if that search |fails. It also includes some code cleanup in the area, as |ath10k_core_fetch_board_data_api_n() no longer does its own string |mangling to remove the variant from an ID, instead leaving that job to a |new flag passed to ath10k_core_create_board_name(). | |I've tested this patch on a QCA4019 and verified that the driver behaves |correctly for 1) both fallback and variant BDFs present, 2) only fallback |BDF present, and 3) no matching BDFs present. | |Fixes: 1657b8f84ed9 ("ath10k: search SMBIOS for OEM board file extension") |Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Note: 937-ath10k-calibration-variant.patch has been reassigned a new 081 number, as it now ships with upstream.... But also because this patch requires the change in ath10k_core_create_board_name(). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx/ipq806x: move qcom-dwc3 usb driver to genericMathias Kresin2018-03-141-0/+36
| | | | | | | If the a kernel package exists within multiple targets an error/warning is shown. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: add targetJohn Crispin2018-03-146-7/+50
| | | | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
* e2fsprogs: break out libcomerr/libss, FS#1310Andy Walsh2018-03-142-17/+117
| | | | | | | | | | | | | | | | | libext2fs breaks krb5 by always installing its own copies of libcom_err.so and libss.so. Move the libraries into separate libcomerr and libss packages respectively and add a host build recipe to stage the required compile_et and mk_cmds utilities for use by other packages. This allows the krb5 package to be fixed to use the system wide libcomerr and libss libraries. Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com> [rename libcom_err to libcomerr, make compile_et and mk_cmds relocatable, cleanup makefile, add dependency on host build, reword commit message] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* jsonfilter: update to latest git HEADJo-Philipp Wich2018-03-141-3/+3
| | | | | | | | c7e938d implement POSIX regexp support cd6629f lexer: fix encoding 7 bit escape sequences 8614470 main: implement array mode Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* dnsmasq: bump to 2.79rc2Hans Dedecker2018-03-131-2/+2
| | | | | | | | | | | | | | | | | | ae29065 Fix debian/changelog syntax. 6b2b564 Enhance --synth-domain to allow names with sequential integers. 4f7bb57 Fix deletion of dhcp-options from inotify dynamic files. 56f0623 Allow trailing dot in CNAME. f3223fb Fix nettle_hash() function to avoid ABI incompatibilities. 4c4f4c2 Debian dependency tweaking for new dnsmasq-base-lua package. 773af30 Man page typo fix. 4cc944b Merge branch 'master' of ssh://thekelleys.org.uk/var/local/git/dnsmasq 87e00fe Compiler warning fixes. e7a4af8 Compiler warning fixes. 2d69d61 Add liblua-dev to Debian build-depends. 30e4a94 Debian package: add dnsmasq-base-lua binary package. 232a8f3 Merge messages for release. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* uboot-imx6: fix build with GCC 7Hauke Mehrtens2018-03-134-5/+1344
| | | | | | | | Backport the compiler support patches from upstream u-boot to this older version to make it compile with GCC 7. This was found by build bot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* 6in4: support multiple additional user prefixesJo-Philipp Wich2018-03-132-6/+11
| | | | | | | | | | | | | | Support configuration in the form... list ip6prefix 2001:db8:1234::/64 list ip6prefix 2001:db8:5678::/64 ... to allow specifying multiple routed IPv6 prefixes. Implements feature request FS#1361. Signed-off-by: Jo-Philipp Wich <jo@mein.io> Acked-by: Hans Dedecker <dedeckeh@gmail.com>
* netifd: update to the latest version (fixes FS#1358)Felix Fietkau2018-03-131-3/+3
| | | | | | | | 1f5a29c ip: do not add local routes for host dependencies c06f842 device: add support for setting the isolate options for bridge ports 69aeaab interface-ip: fix route selection for host dependencies Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ppp: make ppp-multilink provide pppFelix Fietkau2018-03-121-9/+10
| | | | | | Fixes dependencies on ppp from other packages Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uboot-fritz4040: fix build with gcc7Felix Fietkau2018-03-121-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* busybox: remove i386-specific build flagsMatthias Schiffer2018-03-121-0/+10
| | | | | | | | | | busybox tries to be smart and passes a number of additional flags to the compiler. Unfortunately, the i386-specific flags break ABI compatiblity with libc. Fixes busybox crashes observed on x86-generic with GCC 7. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* mac80211: minstrel: make short preamble CCK available when not used at ↵Felix Fietkau2018-03-101-4/+12
| | | | | | | | | connect time The BSS short preamble state can change without rate control update notification. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix a tx queue memory accounting errorFelix Fietkau2018-03-101-0/+66
| | | | | | Fixes rare hard to trigger tx hangs after some time Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: Add subtarget for Cortex A9 buildHauke Mehrtens2018-03-101-0/+1
| | | | | | This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: add support for Turris OmniaRyan Mounce2018-03-101-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Turris Omnia and builds an eMMC sysupgrade image in the same format as the SolidRun ClearFog. An initramfs image in the simple yet Omnia-specific 'medkit' image format is also built in order to ease the initial flashing process. Notable hardware support omissions are support for switching between SFP cage and copper PHY, and RGB LED control. Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used. Specifications: - Marvell Armada 385 1.6GHz dual-core ARMv7 CPU - 1GB DDR3 RAM - 8GB eMMC Flash - 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports) - 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN - 2x USB 3.0 - 12x dimmable RGB LEDs controlled by independent MCU - 3x Mini PCIe slots - Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz) - Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz) - Optional Quectel EC20 Mini PCIe LTE modem Flash instructions: If the U-Boot environment has been modified previously (likely manually via serial console), first use serial to reset the default environment. => env default -a => saveenv Method 1 - USB 'medkit' image w/o serial - Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS. Note that the medkit MUST be named omnia-medkit*.tar.gz - Disconnect other USB devices from the Omnia and connect the flash drive to either USB port. - Power on the Omnia and hold down the rear reset button until 4 LEDs are illuminated, then release. - Wait approximately 2 minutes for the Turris Omnia to flash itself with the temporary image, during which LEDs will change multiple times. - Connect a computer to a LAN port of the Turris Omnia with a DHCP client - (if necessary) ssh-keygen -R 192.168.1.1 - ssh root@192.168.1.1 $ mount /dev/sda1 /mnt $ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself and you can remove the flash drive. Method 2 - TFTP w/ serial - Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy dtb + zImage to your TFTP server (rename if desired) - Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server - Connect serial console and interrupt U-Boot => dhcp => setenv serverip <tftp_server_ip_here> => tftpboot 0x01000000 zImage => tftpboot 0x02000000 dtb => bootz 0x01000000 - 0x02000000 - OpenWrt will now boot from ramdisk - Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/ $ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* firmware: ath10k-firmware: update QCA9984 firmware to 10.4-3.5.3-00053Henryk Heisig2018-03-091-1/+1
| | | | | | | | | | | | | | | | | | | This patch updates ath10k-firmware to use the firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9984. The update fixes "ath10k_pci 0001:01:00.0: Invalid VHT mcs 15 peer stats" spamming the kernel ring buffer at very high frequencies, but introduces the new "ath10k_pci 0001:01:00.0: Unknown eventid: 36925". This new warning doesn't appear to cause problems in practice and is only emitted relatively rarely, not causing dmesg to overflow within minutes. Tested on the ZyXEL NBG6817; early feedback also suggests this firmware to work well (with the same fixes and caveats) on the Netgear r7800 as well. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* firmware: ath10k-firmware: update to 2018-02-09Henryk Heisig2018-03-091-4/+4
| | | | | | | This patch updates ath10k-firmware to last commit and use the firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9888. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* util-linux: added unshare and nsenter executablesToni Uhlig2018-03-091-0/+30
| | | | Signed-off-by: Toni Uhlig <matzeton@googlemail.com>
* iperf3: update to 3.5Philip Prindeville2018-03-092-67/+2
| | | | | | Get rid of patches which are already upstream. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* openvpn: update to 2.4.5Magnus Kroken2018-03-094-24/+19
| | | | | Signed-off-by: Magnus Kroken <mkroken@gmail.com> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* linux-firmware: bump firmware for Intel Wireless 8260AC to version 31Stijn Segers2018-03-091-1/+1
| | | | | | Bump the firmware for 8260AC and related hardware to version 31. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* ebtables: update to latest git 2018-01-17Hans Dedecker2018-03-081-3/+3
| | | | | | 068ba95 Fix locking if LOCKDIR does not exist Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* firewall: bump to git HEADStijn Tintel2018-03-081-3/+5
| | | | | | | | | | | 392811a ubus: let fw3_ubus_address() return the number of resolved addresses 359adcf options: emit an empty address item when resolving networks fails 503db4a zones: disable masq when resolving of all masq_src or masq_dest items failed f50a524 helpers: implement explicit CT helper assignment support a3ef503 zones: allow per-table log control 8ef12cb iptables: fix possible NULL pointer access on constructing rule masks Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* base-files: tune fragment queue thresholds for available system memoryMatthias Schiffer2018-03-072-10/+21
| | | | | | | | | The default fragment low/high thresholds are 3 and 4 MB. On devices with only 32MB RAM, these settings may lead to OOM when many fragments that cannot be reassembled are received. Decrease fragment low/high thresholds to 384 and 512 kB on devices with less than 64 MB RAM. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* imagebuilder: reuse rootfs preparation from rootfs.mkMatthias Schiffer2018-03-071-0/+1
| | | | | | | | | | | | In addition to removing redundant code, this fixes various issues in IB-generated images that have been fixed in prepare_rootfs before, including better handling of CONFIG_CLEAN_IPKG and enabling of initscripts from FILES. We also reuse the opkg macro and remove --force-... flags that have been removed from rootfs.mk as well. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* include/rootfs.mk: pass additional files dir to prepare_rootfs as an argumentMatthias Schiffer2018-03-071-1/+1
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* base-files: sysupgrade: do not rely on opkg to list changed conffilesMatthias Schiffer2018-03-072-2/+21
| | | | | | | Many packages use the opkg conffiles field to list configuration files that are to be retained on upgrades. Make this work on systems without opkg. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* lantiq: ltq-adsl: deactivate ASLR supportMathias Kresin2018-03-061-0/+1
| | | | | | | | The package still leaks some user space linker options into the kernel space. This breaks the build when ASLR is activated, deactivate it for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* wireguard: bump to 20180304Jason A. Donenfeld2018-03-061-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 7c0d711 version: bump snapshot b6a5cc0 contrib: add extract-handshakes kprobe example 37dc953 wg-quick: if resolvconf/run/iface exists, use it 1f9be19 wg-quick: if resolvconf/interface-order exists, use it 4d2d395 noise: align static_identity keys 14395d2 compat: use correct -include path 38c6d8f noise: fix function prototype 302d0c0 global: in gnu code, use un-underscored asm ff4e06b messages: MESSAGE_TOTAL is unused ea81962 crypto: read only after init e35f409 Kconfig: require DST_CACHE explicitly 9d5baf7 Revert "contrib: keygen-html: rewrite in pure javascript" 6e09a46 contrib: keygen-html: rewrite in pure javascript e0af0f4 compat: workaround netlink refcount bug ec65415 contrib: embedded-wg-library: add key generation functions 06099b8 allowedips: fix comment style ce04251 contrib: embedded-wg-library: add ability to add and del interfaces 7403191 queueing: skb_reset: mark as xnet Changes: * queueing: skb_reset: mark as xnet This allows cgroups to classify packets. * contrib: embedded-wg-library: add ability to add and del interfaces * contrib: embedded-wg-library: add key generation functions The embeddable library gains a few extra tricks, for people implementing plugins for various network managers. * crypto: read only after init * allowedips: fix comment style * messages: MESSAGE_TOTAL is unused * global: in gnu code, use un-underscored asm * noise: fix function prototype Small cleanups. * compat: workaround netlink refcount bug An upstream refcounting bug meant that in certain situations it became impossible to unload the module. So, we work around it in the compat code. The problem has been fixed in 4.16. * contrib: keygen-html: rewrite in pure javascript * Revert "contrib: keygen-html: rewrite in pure javascript" We nearly moved away from emscripten'ing the fiat32 code, but the resultant floating point javascript was just too terrifying. * Kconfig: require DST_CACHE explicitly Required for certain frankenkernels. * compat: use correct -include path Fixes certain out-of-tree build systems. * noise: align static_identity keys Gives us better alignment of private keys. * wg-quick: if resolvconf/interface-order exists, use it * wg-quick: if resolvconf/run/iface exists, use it Better compatibility with Debian's resolvconf. * contrib: add extract-handshakes kprobe example Small utility for extracting ephemeral key data from the kernel's memory. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (git log --oneline description)
* nghttp2: bump to 1.31.0Hans Dedecker2018-03-051-2/+2
| | | | | | | | | | | | | | | | | | | | | 6e744662 Update bash_completion 478eac09 Update manual pages 88e2029e Bump up version number to 1.31.0, LT revision to 30:0:16 45d76cf5 nghttpx: Close listening socket on graceful shutdown 54573f28 Merge pull request #1137 from nghttp2/session-set-user-data 17793e99 Add nghttp2_session_set_user_data() public API function 5eac3c90 Update manual pages e70195ae nghttpx: Update doc fe51e7fa Merge pull request #1130 from nghttp2/avoid-inet_pton-macro eb951c2c src: Define nghttp2_inet_pton wrapper to avoid inet_pton macro 39f0ce7c Merge pull request #1126 from nghttp2/nghttpx-expired-client-cert 65157811 Merge pull request #1123 from nghttp2/mruby-client-cert-not-before-after e8af7afc nghttpx: Add an option to accept expired client certificate 38abfd18 nghttpx: Add mruby tls_client_not_before, and tls_client_not_after ff3edc09 nghttpx: Fix potential memory leak 0bb15406 Bump up version number to 1.31.0-DEV Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mt76: update to the latest versionFelix Fietkau2018-03-041-3/+3
| | | | | | | cda627f mt76: add missing VHT maximum A-MPDU length capability ffa2069 mt76: fix potential sleep in atomic context Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: remove an old kernel compatibility line from module packagingFelix Fietkau2018-03-041-4/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: avoid sampling rates that are too slow, improves throughputFelix Fietkau2018-03-031-0/+40
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: Deactivate ASLR support for some applicationsHauke Mehrtens2018-03-036-1/+6
| | | | | | | | | The lantiq components still leak some user space linker options into the kernel space. This breaks with build when ASLR is activated, deactivate it for now on these packages. Fixes: FS#1391 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: ltq-vmmc: Do not leak user space CFLAGS into kernel spaceHauke Mehrtens2018-03-032-2/+20
| | | | | | | Do not leak the user space CFLAGS into the kernel space any more, this allows us to activate the MIPS16 build. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: ltq-tapi: Do not leak user space CFLAGS into kernel spaceHauke Mehrtens2018-03-032-2/+28
| | | | | | | Do not leak the user space CFLAGS into the kernel space any more, this allows us to activate the MIPS16 build. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: ltq-adsl: Do not leak user space CFLAGS into kernel spaceHauke Mehrtens2018-03-036-104/+96
| | | | | | | Do not leak the user space CFLAGS into the kernel space any more, this allows us to activate the MIPS16 build. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: ltq-vdsl: Do not leak user space CFLAGS into kernel spaceHauke Mehrtens2018-03-032-5/+34
| | | | | | | Do not leak the user space CFLAGS into the kernel space any more, this allows us to activate the MIPS16 build. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: ltq-vdsl-mei: Do not leak user space CFLAGS into kernel spaceHauke Mehrtens2018-03-032-3/+23
| | | | | | | | | Do not leak the user space CFLAGS into the kernel space any more, this allows us to activate the MIPS16 build. This decreases the size of the ipk file from 87589 bytes to 81267 bytes. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: ltq-ifxos: Do not force O3 build any moreHauke Mehrtens2018-03-033-6/+20
| | | | | | | Do not force to build with O3 optimization any more, but take what was selected by the OpenWrt build system. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: ltq-ifxos: activate build with mips16Hauke Mehrtens2018-03-031-1/+0
| | | | | | | | | | | | | | | | | The build process does not leak the user space cflags into the kernel build process any more, this allows to activate MIPS16 builds. This was fixed with some update of ifxos. This decreases size of the libifxos.a and the ltq-vdsl-app old: 78320 libifxos.a 44383 ltq-vdsl-app_4.17.18.6-2_mips_24kc.ipk new: 66852 libifxos.a 43506 ltq-vdsl-app_4.17.18.6-2_mips_24kc.ipk Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mwlwifi: Update to version 10.3.4.0-20180226Kabuli Chana2018-03-022-6/+58
| | | | | | move to latest version, address vfs_write issue Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
* gre: squash grev4 and grev6 packages into gre (FS#1399)Hans Dedecker2018-03-021-34/+5
| | | | | | | | | The split-up into packages gre, grev4 and grev6 causes confusion for the users as reported in FS#1399. As IPv4 and IPv6 are considered now as bundled; squash the grev4 and grev6 packages into the gre package and let gre provide both grev4 and grev6. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* netifd: add udhcpc link check to dhcp shell handler scriptHans Dedecker2018-03-022-1/+3
| | | | | | | | Fixes the assumption the busybox udhcpc applet is always enabled; in case the symbolic link check fails the DHCP shell handler script will exit and as result the DHCP protocol handler will not be registered in netifd. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>