aboutsummaryrefslogtreecommitdiffstats
path: root/package/switch
Commit message (Collapse)AuthorAgeFilesLines
* switch: export name of device found via /procHauke Mehrtens2013-02-144-1/+16
| | | | SVN-Revision: 35596
* switch: export cpuport, ports and vlans via /procHauke Mehrtens2013-02-141-0/+21
| | | | SVN-Revision: 35595
* switch: add support for BCM53125Hauke Mehrtens2013-02-131-3/+14
| | | | SVN-Revision: 35586
* switch: resetting and enabling vlan write for gigabit switchesHauke Mehrtens2013-02-131-7/+45
| | | | | | | | This patch makes it possible to reset and enable writing vlans to recent switchs. This is based on a patch by jcharest and the Broadcom SDK. SVN-Revision: 35585
* switch: read and write vlan config from and to gigabit switchesHauke Mehrtens2013-02-131-30/+105
| | | | | | | | This patch makes it possible to read and write the vlan config from and to recent switchs. This is based on a patch by jcharest and the Broadcom SDK. SVN-Revision: 35584
* switch: improve robo_switch_enable()Hauke Mehrtens2013-02-131-2/+6
| | | | | | This is based on a patch by jcharest and the Broadcom SDK. SVN-Revision: 35583
* switch: fix switches with more than 6 portsHauke Mehrtens2013-02-131-4/+9
| | | | | | This is based on a patch by jcharest and the Broadcom SDK. SVN-Revision: 35582
* switch: reverse if else in handle_vlan_port_read()Hauke Mehrtens2013-02-131-14/+16
| | | | SVN-Revision: 35581
* switch: the BCM5365 is a special switch and the BCM5350 or BCM5325 is the ↵Hauke Mehrtens2013-02-132-47/+40
| | | | | | | | normal case. This makes it easier to compare this code with the code from the Broadcom SDK. SVN-Revision: 35580
* switch: reset switch before using it.Hauke Mehrtens2013-02-131-2/+70
| | | | SVN-Revision: 35579
* switch: improve error handling in robo_probe()Hauke Mehrtens2013-02-131-13/+16
| | | | SVN-Revision: 35578
* switch: run cleanfile over the source codeHauke Mehrtens2013-02-131-3/+3
| | | | SVN-Revision: 35577
* bcm63xx: switch to b53 and swconfigJonas Gorski2013-01-231-1/+1
| | | | | | | | | | | | | | | | | Switch to using the B53 switch driver where appropriate. Use a non-tagged default config where it isn't confirmed to be working. Remove the switch configuration in preinit as the switch will now be configured by the driver to use port isolation to prevent leakage between lan and wan. While at it, also provide a switch config for Neufbox 6. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 35307
* switch: ROBO Switch Gigabit MII SupportHauke Mehrtens2013-01-036-35/+155
| | | | | | | | | | | | | | | | | | | | | | | I wrote this patch some time ago because I had a need for one of the Gigabit ports (Linksys E3000) to be forced to 100FD. This is based on the robocfg sources included w/ the RT-N16 sources from ASUS. Since work is progressing on a BGMAC driver that could be included in OpenWRT, this may be useful to someone else. In testing, forcing the speed to 10/100 or 1000 worked fine; however, when trying to force full-duplex mode, the result was always half-duplex. I was not able to isolate the source of the problem (this patch, driver or H/W limitation). The only way I could get it to work was to set the port to Auto, but then only advertise 100FD (not included in this patch). I have a modified version of the robocfg package as well, I'd have to clean it up a little first (remove the full-duplex hack) before submitting it if there is interest. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> SVN-Revision: 34992
* switch: improve error messagesHauke Mehrtens2013-01-031-15/+14
| | | | | | This is in part based on a patch send by Nathan Hintz <nlhintz@hotmail.com> SVN-Revision: 34991
* brcm47xx: add a new version of the nvram rewrite patchHauke Mehrtens2013-01-032-8/+8
| | | | | | This is the version like it was send for mainline inclusion. SVN-Revision: 34988
* switch: warn if ndo_do_ioctl is not implemented in the Ethernet driverHauke Mehrtens2012-09-221-0/+4
| | | | SVN-Revision: 33506
* switch: improve error messageHauke Mehrtens2012-09-191-4/+9
| | | | SVN-Revision: 33464
* switch: clean up robo switch driverHauke Mehrtens2012-08-051-98/+42
| | | | | | | | | | * remove use_et, all supported drivers are using mii ioctls * remove robo.phy_addr, phy_addr was always set to ROBO_PHY_ADDR. * remove support for old kernel versions * do_ioctl is allways called with buff == NULL * use if_mii SVN-Revision: 33002
* brcm47xx: use libgpio instaed of implementing the gpio interface ourself.Hauke Mehrtens2012-08-043-79/+24
| | | | SVN-Revision: 32992
* switch: the hardware must be up while configuring Since the removal of the ↵Jo-Philipp Wich2012-03-132-2/+3
| | | | | | interface coldplug hack the timing changed in such a way that eth0 is not up during switch setup, leading to an inaccesible device. Bring up the switch interface before configuring it to mitigate the problem. SVN-Revision: 30937
* switch: fix some memory leaks in switch_parse_vlan()Hauke Mehrtens2012-01-283-7/+8
| | | | SVN-Revision: 29936
* switch: update for brcm47xx targetHauke Mehrtens2011-08-047-102/+83
| | | | | | | * remove suport for 2.4 kernel * add support for bcma bus SVN-Revision: 27904
* switch: fix switch-robo device reference countingFlorian Fainelli2011-02-202-7/+16
| | | | | | | | Fix incorrect device reference counting by switch-robo. Signed-off-by: George Kashperko <george@znau.edu.ua> SVN-Revision: 25619
* remove whitespaces in kmod-switch sourcesFlorian Fainelli2010-07-203-56/+56
| | | | SVN-Revision: 22320
* massive: replace occurences of .$(LINUX_KMOD_SUFFIX) with .ko after r21950Claudio Mignanti2010-07-121-3/+3
| | | | SVN-Revision: 22145
* remove linux 2.4 support from several packagesFelix Fietkau2010-06-264-27/+3
| | | | SVN-Revision: 21954
* switch: explicitely clear port mappings in unsused vlans (#7082)Jo-Philipp Wich2010-04-052-1/+7
| | | | SVN-Revision: 20717
* switch: suppress boot error message on 2.4Nicolas Thill2010-03-011-2/+2
| | | | SVN-Revision: 19922
* switch: eliminate the asterisk from the switch port configuration and set it ↵Jo-Philipp Wich2010-02-281-1/+9
| | | | | | automatically on the first vlan, this aligns the broadcom vlan config with the swconfig format SVN-Revision: 19909
* switch: do not include linux/autoconf.h (#6513)Florian Fainelli2010-02-283-3/+0
| | | | SVN-Revision: 19903
* change switch config to swconfig style format to remain consistent accross ↵Jo-Philipp Wich2009-11-151-25/+30
| | | | | | platforms SVN-Revision: 18425
* fix breakage on wl500gp after r18214, thanks sn9 (#6084)Florian Fainelli2009-11-031-2/+2
| | | | SVN-Revision: 18289
* make etehrent work on wrt350n, thx sn9John Crispin2009-10-291-2/+25
| | | | SVN-Revision: 18214
* add patches for kernel 2.6.31Hauke Mehrtens2009-09-261-0/+4
| | | | | | This is completly untested. Only a compile tests with the default config was done! SVN-Revision: 17734
* fix oops in switch-robo on brcm63xx, thanks to Daniel Dickinson (#5053)Florian Fainelli2009-05-051-1/+1
| | | | SVN-Revision: 15611
* prevent kmod-switch from accessing nvram on brcm63xx (#5035)Florian Fainelli2009-05-021-1/+5
| | | | SVN-Revision: 15555
* fix nvram_get checking on non-WGT634U (#4975)Florian Fainelli2009-04-211-1/+2
| | | | SVN-Revision: 15319
* fix strange LED behavior with Netgear WGT634U (#3552)Florian Fainelli2009-04-202-3/+7
| | | | SVN-Revision: 15290
* get rid of $Id$ - it has never helped us and it has broken too many patches ;)Felix Fietkau2009-04-174-4/+0
| | | | SVN-Revision: 15242
* allow kmod-switch to be used on brcm63xx (#4599)Florian Fainelli2009-03-093-4/+14
| | | | SVN-Revision: 14825
* switch: remove message about BFL_ENETADM not being set on systems with a ↵Felix Fietkau2008-11-021-3/+2
| | | | | | roboswitch SVN-Revision: 13100
* (4/6) bcm57xx: switch-core.c/switch-robo.c check for port already registeredFelix Fietkau2008-06-153-1/+19
| | | | | | | | | | | | This patch prevents switch-robo.c from attempting robo_probe on a port that is already registered. robo_probe will adjust kernel reference counts if it detects a switch on the port. If this patch wasn't applied, the wrt350n would hang on reboot, waiting for the network driver reference count to reach zero indefinitely. Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu> SVN-Revision: 11469
* Stopgap compilation fixes for diag and switch under 2.6.25Peter Denison2008-05-201-0/+4
| | | | SVN-Revision: 11231
* Allow package/switch to compile against 2.6.25Peter Denison2008-05-141-0/+4
| | | | SVN-Revision: 11138
* Check the return values of kmalloc()Michael Büsch2008-03-131-6/+25
| | | | SVN-Revision: 10599
* fix switch-robo.c compile errors on linux 2.4Felix Fietkau2008-03-011-0/+4
| | | | SVN-Revision: 10539
* Fix the roboswitch code for the WRT350NMichael Büsch2008-02-273-80/+186
| | | | SVN-Revision: 10531
* ssb: Make the GPIO API reentrancy safe.Michael Büsch2008-02-191-22/+7
| | | | SVN-Revision: 10496
* export switch-core.h to $(STAGING_DIR)Felix Fietkau2008-01-061-1/+10
| | | | SVN-Revision: 10138