aboutsummaryrefslogtreecommitdiffstats
path: root/package/kernel
Commit message (Collapse)AuthorAgeFilesLines
* mac80211: add missing change for encap offload on devices with sw rate controlFelix Fietkau2021-08-243-21/+65
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: refresh patchFelix Fietkau2021-08-241-12/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix HT40 mode for 6G bandFelix Fietkau2021-08-241-3/+4
| | | | | | The channel offset used for VHT segment calculation was missing for HT Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ltq-vdsl: add missing backslashJan Hoffmann2021-08-211-2/+2
| | | | | | This error was introduced with the recent cleanup. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* bcm27xx-gpu-fw: update to latest versionÁlvaro Fernández Rojas2021-08-211-15/+15
| | | | | | Multiple firmware fixes needed for kernel updates. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ltq-vdsl/ltq-vdsl-app: clean up configure argsJan Hoffmann2021-08-211-8/+5
| | | | | | | | | | | | | | | | | | | | | The userspace application now uses the model=full option to match the configuration of the kernel module. The source no longer contains SOAP support, which was the primary reason to build only typical instead of full before. This makes several CLI commands, which were already supported in the kernel module, available in the userspace application. For example, this includes bbsg which allows to get information about VDSL2 bands. Some previously applied build options were redundant. Disabling ADSL MIB support is unnecessary, as it only applies to Danube. ADSL LED support is no longer included in the source. ReTx counters are already included with model type full. This increases the size of the userspace application by approximately 15 kB (uncompressed). The kernel module does not change at all. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* kernel: kmod-xfrm-interface requires IPv6Stijn Tintel2021-08-061-1/+1
| | | | | | | | The xfrm_interface module will not be built if IPv6 is not enabled in the kernel. Add this dependency in the kmod package to avoid people wondering why it doesn't build when they disabled IPv6. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* treewide: backport support for nvmem on non platform devicesAnsuel Smith2021-08-055-50/+462
| | | | | | | | | | | | In the current state, nvmem cells are only detected on platform device. To quickly fix the problem, we register the affected problematic driver with the of_platform but that is more an hack than a real solution. Backport from net-next the required patch so that nvmem can work also with non-platform devices and rework our current patch. Drop the mediatek and dsa workaround and rework the ath10k patches. Rework every driver that use the of_get_mac_address api. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* nat46: fix translation of ICMP protocols parameter problem and unreachableHans Dedecker2021-08-011-3/+3
| | | | | | 9b3a819 nat46-core: Fix translation of ICMP protocols parameter problem and unreachable (#27) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: add missing symbol to kmod-qlcnicStijn Tintel2021-07-231-1/+2
| | | | | | | | When the kmod-qlcnic package is built on targets that have CONFIG_PCI_IOV enabled, the CONFIG_QLCNIC_SRIOV symbol is exposed. Enable this symbol in the kmod package to fix its build. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ath10k: fix compilation error with CONFIG_OF not availableAnsuel Smith2021-07-192-2/+6
| | | | | | | | of_platform_device_create require CONFIG_OF selected. Add an ifdef and register to the of platform only if of is available. Fixes: 985954ccbd11 ("kernel: add ath10k support for of_get_mac_address") Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* kernel: add ath10k support for of_get_mac_addressAnsuel Smith2021-07-192-0/+118
| | | | | | | ath10k doesn't currently support the standard function to get mac-address from the dts. Add this for both ath10k and ath10k-ct Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* mt76: update to the latest versionFelix Fietkau2021-07-151-3/+3
| | | | | | bbebea7d6dc6 Revert "mt76: fix mt76_rates for the multiple devices" Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mt76: update to the latest versionFelix Fietkau2021-07-141-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 624c681ef0c6 mt76: mt7921: enable VHT BFee capability a27dfcb63ccf mt76: connac: fix UC entry is being overwritten 6b691e62470e mt76: connac: add mt76_connac_power_save_sched in mt76_connac_pm_unref b14365bea586 mt76: mt7921: wake the device before dumping power table 82af16bddfc0 mt76: mt7921: make mt7921_set_channel static b24598b1c1a9 mt76: connac: add mt76_connac_mcu_get_nic_capability utility routine 5954e3381ff9 mt76: testmode: move chip-specific stats dump before common stats fd5b612f9aa4 mt76: mt7915: fix rx fcs error count in testmode d9d26a294f7b mt76: connac: fix the maximum interval schedule scan can support ed39c882f388 mt76: reduce rx buffer size to 2048 60f3d3adbba6 mt76: move mt76_get_next_pkt_id in mt76.h 67ed4d902c84 mt76: connac: check band caps in mt76_connac_mcu_set_rate_txpower 23c6ec49c000 mt76: make mt76_update_survey() per phy 5ca602fb9455 mt76: mt7915: introduce mt7915_mcu_set_txbf() c13df42282e9 mt76: mt7915: improve MU stability dee7dcddcaa0 mt76: use SPDX header file comment style 6fbd47153b3d mt76: mt7915: fix IEEE80211_HE_PHY_CAP7_MAX_NC for station mode 1b97dd1762ca mt76: mt7921: fix sta_state incorrect implementation 1b89053b5a6f mt76: mt7921: improve code readability for mt7921_update_txs 126649816785 mt76: mt7921: limit txpower according to userlevel power a5163ac09be2 mt76: mt7921: introduce dedicated control for deep_sleep e47c04db4d7e mt76: mt7921: fix kernel warning when reset on vif is not sta 063d3611662c mt76: mt7921: fix the coredump is being truncated 12bf28feba7c mt76: fix iv and CCMP header insertion 949327e76ee4 mt76: disable TWT capabilities for the moment 3530254c1bc9 mt76: mt7921: enable HE BFee capability 599e35f5d9b8 mt76: sdio: do not run mt76_txq_schedule directly 3b6d30c28946 mt76: mt7663s: rely on pm reference counting 529d55a79088 mt76: mt7663s: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path ef44ff116ee2 mt76: mt7663s: enable runtime-pm 3a71e71a555e mt76: mt7615: set macwork timeout according to runtime-pm 925d96e443a4 mt76: mt7921: allow chip reset during device restart 63b114d84361 mt76: mt76x0e: fix device hang during suspend/resume 7f5ea5e2fd10 mt7915: check return code of sysfs_create_link ca64a36908b7 mt76: fix mt76_rates for the multiple devices f517116bf14c mt76: add mt76_default_basic_rate more devices can rely on 6c70b0100513 mt76: mt7921: fix mgmt frame using unexpected bitrate c00a9a6b52af mt76: mt7915: fix mgmt frame using unexpected bitrate 0e4089949565 mt76: mt7921: fix endianness in mt7921_mcu_tx_done_event 55f314120ef2 mt76: mt7921: avoid unnecessary spin_lock/spin_unlock in mt7921_mcu_tx_done_event 541cd3276488 mt76: mt7915: fix endianness warning in mt7915_mac_add_txs_skb 817761e87c4f mt76: mt7921: fix endianness warning in mt7921_update_txs b8eca74bbd7b mt76: mt7615: fix endianness warning in mt7615_mac_write_txwi 5e5e07f0def3 mt76: mt7915: fix potential overflow of eeprom page index abda4cded420 mt76: mt7915: fix info leak in mt7915_mcu_set_pre_cal() 535899f81a46 mt76: mt7915: fix calling mt76_wcid_alloc with incorrect parameter adfa1b9a3ca0 mt76: connac: fix mt76_connac_gtk_rekey_tlv usage 2a65b105ea4a mt76: mt7921: enable aspm by default c57158c82804 mt76: fix build error implicit enumeration conversion 41f607cab83c mt76: mt7921: fix survey-dump reporting 25b4f885a937 mt76: mt76x02: fix endianness warnings in mt76x02_mac.c e63fadb87fe1 mt76: mt7915: report HE MU radiotap 135ef3e9827a mt76: mt7915: adapt new firmware to update BA winsize for Rx session 7118eacb7ce4 mt76: mt7921: add .set_sar_specs support f1f6569da408 mt76: mt7915: fix an off-by-one bound check f7da39467965 mt76 mt7915: take RCU read lock when calling ieee80211_bss_get_elem() 87af8e5c72b1 mt76: mt7915: cleanup -Wunused-but-set-variable 8e2d383fbd92 mt76: mt7915: report tx rate directly from tx status ddce30977591 mt76: mt7915: remove mt7915_sta_stats 4ccd42029519 mt76: mt7921: introduce testmode support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: backport SAR power limit supportFelix Fietkau2021-07-143-7/+456
| | | | | | Needed for an upcoming mt76 update Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: merge a 4-addr client mode fixFelix Fietkau2021-07-141-0/+72
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: merge the virtual time based airtime schedulerFelix Fietkau2021-07-144-3/+1430
| | | | | | Improves airtime fairness, especially for devices with larger firmware buffers Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: backport fix for nl80211 control port tx (fixes FS#3857)Felix Fietkau2021-06-307-17/+133
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix a regression in starting aggregation sessions on mesh interfacesFelix Fietkau2021-06-291-0/+112
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: print an error if wifi teardown failsBob Cantor2021-06-281-0/+4
| | | | | | | | | drv_mac80211_teardown fails silently if the device to be torn down is not defined. This commit prints an error message. branches affected: trunk, 21.02 Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
* mac80211: always call wireless_set_data (FS#3784)Bob Cantor2021-06-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When wifi is turned off, drv_mac80211_teardown sometimes fails (silently) because the device to be torn down is not defined. This situation arises if drv_mac80211_setup was called twice when wifi was turned on. This commit ensures that the device to be torn down is always defined in drv_mac80211_teardown. Steps to reproduce: 1) Use /sbin/wifi to turn on wifi. uci set wireless.@wifi-iface[0].disabled=0 uci set wireless.@wifi-device[0].disabled=0 uci commit wifi 2) Use /sbin/wifi to turn off wifi. uci set wireless.@wifi-device[0].disabled=1 uci commit wifi 3) Observe that wifi is still up. branches affected: trunk, 21.02 Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
* mac80211: fix no_reload logic (FS#3902)Bob Cantor2021-06-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If drv_mac80211_setup is called twice with the same wifi configuration, then the second call returns early with error HOSTAPD_START_FAILED. (wifi works nevertheless, despite the fact that setup is incomplete. But "ubus call network.wireless status" erroneously reports that radio0 is down.) The relevant part of drv_mac80211_setup is, if [ "$no_reload" != "0" ]; then add_ap=1 ubus wait_for hostapd local hostapd_res="$(ubus call hostapd config_add "{\"iface\":\"$primary_ap\", \"config\":\"${hostapd_conf_file}\"}")" ret="$?" [ "$ret" != 0 -o -z "$hostapd_res" ] && { wireless_setup_failed HOSTAPD_START_FAILED return } wireless_add_process "$(jsonfilter -s "$hostapd_res" -l 1 -e @.pid)" "/usr/sbin/hostapd" 1 1 fi This commit sets no_reload = 0 during the second call of drv_mac80211_setup. It is perhaps worth providing a way to reproduce the situation where drv_mac80211_setup is called twice. When /sbin/wifi is used to turn on wifi, uci set wireless.@wifi-iface[0].disabled=0 uci set wireless.@wifi-device[0].disabled=0 uci commit wifi /sbin/wifi makes the following ubus calls, ubus call network reload ubus call network.wireless down ubus call network.wireless up The first and third ubus calls both call drv_mac80211_setup, while the second ubus call triggers wireless_device_setup_cancel. So the call sequence becomes, drv_mac80211_setup wireless_device_setup_cancel drv_mac80211_setup In contrast, when LuCI is used to turn on wifi only a single call is made to drv_mac80211_setup. branches affected: trunk, 21.02 Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
* kernel: crypto: limit crypto-hw-hifn-795x to devices with pci supportAleksander Jan Bajkowski2021-06-221-1/+1
| | | | | | | CONFIG_CRYPTO_DEV_HIFN_795X depends on PCI. This driver only makes sense on devices with pci support. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* bcm63xx-cfe: update to the latest masterRafał Miłecki2021-06-221-4/+4
| | | | | | e5050f3 linksys: ea9500-v2: add cferam file Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel/modules: make sure igb loads at bootChris Blake2021-06-211-1/+1
| | | | | | | | | | Without loading the igb at boot, the recovery wouldn't have network available. All network drivers should be loaded before etc/board.d/02_network is called. Note that other network drivers already have this set, such as tg3. Fixes: 7e0e5110bc90 ("kernel: add igb kernel module") Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ath10k-ct: fix typo in MakefileMichael Yartys2021-06-211-1/+1
| | | | | | Add forgotten colon to Makefile. Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
* mac80211: fix an issue with wds links on 802.11ax devicesFelix Fietkau2021-06-191-0/+51
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: remove extra patch accidentally added during rebaseFelix Fietkau2021-06-181-888/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: remove patches stripping down crypto supportFelix Fietkau2021-06-1812-978/+895
| | | | | | | | Use of WPA3 and things like FILS is getting much more common, and platforms that can't affort the extra kilobytes for this code are fading away. Let's not hold back modern authentication methods any longer Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: system hang caused by deferring calls into minstrel to dequeueFelix Fietkau2021-06-174-40/+127
| | | | | | Move the aggregation check to mac80211 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix minstrel sample time checkFelix Fietkau2021-06-171-0/+23
| | | | | | | | We need to skip sampling if the next sample time is after jiffies, not before. This patch fixes an issue where in some cases only very little sampling (or none at all) is performed, leading to really bad data rates Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: select iwinfoFelix Fietkau2021-06-171-1/+1
| | | | | | Since iwinfo is now used in the core scripts, it needs to be present on the system Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix processing HE capabilities (FS#3871)Felix Fietkau2021-06-171-1/+1
| | | | | | Use the right argument to fix setting unsupported capabilities to 0 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* package: fix cmake packages build with ninjaRosen Penev2021-06-121-0/+1
| | | | | | | | += is needed for CMAKE_OPTIONS. mt76 needs Ninja disabled as the kernel stuff uses normal make. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mac80211: add support for 802.3 encap offload with software rate controlFelix Fietkau2021-06-122-0/+158
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: improve rate control performanceFelix Fietkau2021-06-121-0/+114
| | | | | | Call rate control handler after intermediate queueuing Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: rely on iwinfo for phy->path and path->phy lookupsFelix Fietkau2021-06-104-42/+3
| | | | | | This avoids inconsistencies from having multiple implementations do the same thing Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: Update to backports-5.10.42Hauke Mehrtens2021-06-0634-2349/+63
| | | | | | | | | | | | The removed patches were integrated upstream. The brcmf_driver_work workqueue was removed in brcmfmac with kernel 5.10.42, the asynchronous call was covered to a synchronous call. There is no need to wait any more. This part was removed manually from this patch: brcm/860-brcmfmac-register-wiphy-s-during-module_init.patch Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mt76: update to the latest versionFelix Fietkau2021-06-061-4/+4
| | | | | | | | Add mt7915e dependency on kmod-thermal 22b690334c0f mt76: mt7915: do not fail if the cooling device could not be registered Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: package Synopsys Designware PCI to I2C controllerTomasz Maciej Nowak2021-06-061-0/+29
| | | | | | This is present on Roqos Core RC10 and needed to control LED matrix. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* kernel: usb: add kmod-usb-gadget-ncmKuan-Yi Li2021-06-061-0/+17
| | | | | | | Add kernel module package for USB Network Control Model (NCM) Gadget support. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* ath10k-ct: update to latest versionMichael Yartys2021-06-064-45/+8
| | | | | | | | | | | | | | | | Changelog: - ath10k-ct: Add security fixes. - ath10k-ct: Add 5.12 kernel version. - ath10k-ct: Fix the beacon/mcast/bcast override issue - ath10k-ct 5.7: Fix setting mcast/bcast/beacon rate from debugfs. - ath10k-ct: Add 5.11 driver. Delete upstreamed patch and refresh the rest. Also, use the opportunity to set PKG_RELEASE to $(AUTORELEASE). Runtime-tested on ipq806x (Netgear R7800). Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
* mac80211: split ath patch in dedicated subdirAnsuel Smith2021-06-0449-0/+8
| | | | | | | | | | The ath patch number is already large and adding other patch for ath11k will add more confusion with the patch numbering. Since the support of ath11k based device is imminent, prepare the mac80211 ath patch dir and split it in the dedicated ath5k, ath9k, ath10k and ath11k (empty for now). Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* mac80211: fix typoFelix Fietkau2021-06-031-1/+1
| | | | | | Remove stray parenthesis Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mt76: update to the latest versionFelix Fietkau2021-06-021-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | bddc1db76d0f mt76: mt7915: drop the use of repeater entries for station interfaces 3c90f35dddac mt76: mt7915: add thermal sensor device support afab0e8202ff mt76: mt7915: add thermal cooling device support 41cf02184699 mt76: mt7615: add thermal sensor device support 2ac6b8762565 mt76: connac: update BA win size in Rx direction ddb301127291 mt76: mt7921: fix reset under the deep sleep is enabled e4cbefd1d69a mt76: mt7921: avoid unnecessary consecutive WiFi resets 393eea2034d7 mt76: mt7921: fix invalid register access in wake_work a15d46407ffa mt76: mt7921: fix OMAC idx usage e4d267d8e900 mt76: mt7921: enable runtime pm by default 50fd8ce2412a mt76: connac: add bss color support for sta mode e29058c3c860 mt76: mt7921: return proper error value in mt7921_mac_init c89c8c347b1e mt76: mt7921: do not schedule hw reset if the device is not running 9f7bb428e587 mt76: mt7921: reset wfsys during hw probe 22ea365913b5 mt76: mt7915: add .offset_tsf callback ad91f8e8e494 mt76: mt7615: add .offset_tsf callback 6f871f35e3c1 mt76: mt7915: use mt7915_mcu_get_txpower_sku() to get per-rate txpower 597b68b7daa3 mt76: mt7615: remove useless if condition in mt7615_add_interface() 3945264468eb mt76: testmode: fix memory leak in mt76_testmode_alloc_skb bdcc57a11606 mt76: testmode: remove unnecessary function calls in mt76_testmode_free_skb a9763452601d mt76: testmode: remove undefined behaviour in mt76_testmode_alloc_skb 4aef2a2be464 mt76: mt7615: fix potential overflow on large shift d9dd7635b055 mt76: mt7915: use mt7915_mcu_get_mib_info() to get survey data d740e921758a mt76: mt7921: introduce mac tx done handling 259ddfc7cb73 mt76: mt7921: update statistic in active mode only 757b93f4b179 mt76: mt7921: remove leftover 80+80 HE capability 1fcff599b2e1 mt76: allow hw driver code to overwrite wiphy interface_modes c55c22e39b7d mt7915: update firmware to 2020110522 10548aef1f45 mt76: mt7915: improve error recovery reliability ed6b0c79820c mt76: mt7921: set MT76_RESET during mac reset 321443258bea mt76: move mt76_rates in mt76 module d1652e8af9e1 Revert "mt76: connac: do not schedule wake_work if the runtime-pm is disabled" 4f4cab39ed9f mt76: mt7915: read all eeprom fields from fw in efuse mode 71450535f164 mt76: mt7921: enable hw offloading for wep keys 833d577e430c mt76: mt7921: remove mt7921_get_wtbl_info routine 67b7a22d2b99 mt76: mt7921: enable random mac address during sched_scan cf1ff7bf4f1b mt76: mt7915: setup drr group for peers ef2f7aa8745f mt76: mt7615: update radar parameters b9f09f530223 mt76: mt7915: fix MT_EE_CAL_GROUP_SIZE Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: do not enable VHT in the default config on 2.4 GHzFelix Fietkau2021-06-021-1/+1
| | | | | | | Some drivers advertise it, but it's not supported at the moment Reported-by: John Thomson <git@johnthomson.fastmail.com.au> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix detecting VHT capabilities when generating the default configFelix Fietkau2021-06-021-1/+1
| | | | | | | The colon does not directly follow the "VHT Capabilities" string Reported-by: John Thomson <git@johnthomson.fastmail.com.au> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix AutoLoad parameter for uleds moduleEvgeny Kolesnikov2021-05-261-1/+1
| | | | | | | | The name of the module is 'uleds', not 'leds-uleds'. Signed-off-by: Evgeny Kolesnikov <evgenyz@gmail.com> [improve commit title] Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: sync nl80211.h with upstream and backport a WPA3 related commitFelix Fietkau2021-05-265-33/+382
| | | | | | Fixes compatibility issues with the latest hostapd update Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: add more HE capabilitiesFelix Fietkau2021-05-261-5/+81
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-01 22:23:08 +0000