aboutsummaryrefslogtreecommitdiffstats
path: root/package/firmware
Commit message (Collapse)AuthorAgeFilesLines
* broadcom-sprom: add new packageÁlvaro Fernández Rojas2023-04-231-0/+295
| | | | | | | This adds a new package with Broadcom SPROMs that can be used as fallback when the devices lack physical SPROMs. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ipq-wifi: bump to latest git HEADChristian Marangi2023-04-121-3/+3
| | | | | | | | b22487d ath11k: qcn8074: Update regDb in every BDF 3add8be ath11k: ipq8074: Update regDb in every BDF 8bb6039 ath11k: ipq8074: add Netgear RAX120v2 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ath11k-firmware: update to WLAN.HK.2.9.0.1-01385-QCAHKSWPL_SILICONZ-1Robert Marko2023-04-071-7/+18
| | | | | | | | | | | | | | | | | | | Current WLAN.HK.2.5.0.1 FW is quite old and buggy, but we had to hold off from updating to 2.6.0.1 and 2.7.0.1 as they had compatibility regressions, but now QCA finally released 2.9.0.1 FW which is working on all of the boards. So finally update IPQ8074 and QCN9074 FW to the latest WLAN.HK.2.9.0.1-01385-QCAHKSWPL_SILICONZ-1 firmware. In order to do so, we have to switch to using QCA-s QUIC repo instead of Kalle-s. QCA-s QUIC repo does not have BDF-s so we have to get the QCN9074 BDF from Kalles repo. Tested-by: Mireia Fernández Casals <meirin.f@gmail.com> # Xiaomi AX3600 Tested-by: Francisco G Luna <frangonlun@gmail.com> #Netgear WAX218 Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq-wifi: bump to latest git HEADChristian Marangi2023-03-271-3/+3
| | | | | | | | ccd7e46 ipq40xx: add support for Wallystech DR40x9 2ce60e1 Revert "ipq40xx: add support for Wallystech DR40x9" ea962ca ipq40xx: add Emplus WAP551 BDF Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: add support for Wallystech DR40x9Robert Marko2023-03-211-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Wallys DR40x9 series boards. They come in IPQ4019 and IPQ4029 versions. IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures. Specifications are: * CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz * RAM: 512 MB * Storage: 2MB of SPI-NOR, 128 MB of parallel NAND * USB 3.0 TypeA port for users * MiniPCI-E with PCI-E 2.0 link * MiniPCI-E for LTE modems with only USB2.0 link * 2 SIM card slots that are selected via GPIO11 * MicroSD card slot * Ethernet: 2x GBe with 24~48V passive POE * SFP port (Does not work, I2C and GPIO's not connected on hardware) * DC Jack * UART header * WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac * 4x MMCX connectors for WLAN * Reset button * 8x LED-s Installation instructions: Connect to UART, pins are like this: -> 3.3V | TX | RX | GND Settings are 115200 8n1 Boot initramfs from TFTP: tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb bootm Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name> The board file binary was provided from Wallystech on March 14th 2023 including full permission to use and distribute. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* ipq-wifi: bump to latest git HEADKoen Vandeputte2023-03-211-3/+3
| | | | | | f9cece0 ipq40xx: add support for Wallystech DR40x9 Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* linux-firmware: update to 20230310Nick Hainke2023-03-201-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changes: 588dd07 qat: update licence text a03713d rtl_bt: Update RTL8822C BT USB firmware to 0x0CC6_D2E3 63dac62 rtl_bt: Update RTL8822C BT UART firmware to 0x05C6_D2E3 5adebcf WHENCE: remove duplicate File entries d32de23 WHENCE: remove trailing white space 24c9df9 linux-firmware: add fw for qat_4xxx b568bbc Fix symlinks for Intel firmware f49c572 linux-firmware: update firmware for mediatek bluetooth chip (MT7921) db6e357 linux-firmware: update firmware for MT7921 WiFi device 4309412 iwlwifi: update core69 and core72 firmwares for Ty device 4cc3eda rtlwifi: Add firmware v16.0 for RTL8710BU aka RTL8188GU 76ad275 brcm: Add nvram for the Lenovo Yoga Book X90F / X90L convertible 1bc8afb brcm: Fix Xiaomi Inc Mipad2 nvram/.txt file macaddr d02d58a brcm: Add nvram for the Advantech MICA-071 tablet c51488f rtl_bt: Update RTL8852C BT USB firmware to 0xD7B8_FABF 3653d69 rtl_bt: Add firmware and config files for RTL8821CS 7375bcf rtw89: 8852b: update fw to v0.29.29.0 5148670 rtw89: 8852b: update fw to v0.29.26.0 c600840 liquidio: remove lio_23xx_vsw.bin 23afbfe intel: avs: Add AudioDSP base firmware for CNL-based platforms 284e55d intel: avs: Add AudioDSP base firmware for APL-based platforms 289e3a9 intel: avs: Add AudioDSP base firmware for SKL-based platforms c7a57ef ath11k: WCN6855 hw2.0: update to WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23 6a4e7f6 ath11k: WCN6855 hw2.0: update board-2.bin 0e2486b ath11k: WCN6750 hw1.0: update board-2.bin f48fbe4 ath11k: IPQ5018 hw1.0: add to WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1 9dacec6 ath11k: IPQ5018 hw1.0: add board-2.bin 15054af ath10k: QCA6174 hw3.0: update firmware-sdio-6.bin to version WLAN.RMH.4.4.1-00174 024cc5e ath10k: WCN3990 hw1.0: update board-2.bin a253a37 cnm: update chips&media wave521c firmware. c0a0bc2 amdgpu: Update GC 11.0.1 firmware 4296b7a intel: catpt: Add AudioDSP base firmware for BDW platforms f79e4ba linux-firmware: Update AMD cpu microcode 1fd4c55 brcm: revert firmware files for Cypress devices 5aa0b27 brcm: restore previous firmware file for BCM4329 device c3f3baa rtw88: 8822c: Update normal firmware to v9.9.14 c1181ae i915: Add DMC v2.11 for MTL 2fd61bc linux-firmware: Add firmware for Cirrus CS35L41 on UM3402 ASUS Laptop a60d908 linux-firmware: Add missing tuning files for HP Laptops using Cirrus Amps a5046f4 i915: Add DMC v2.18 for ADLP 5c11a37 amdgpu: Add VCN 4.0.2 firmware 5fe2d73 amdgpu: Add PSP 13.0.4 firmware a3332f8 amdgpu: Add SDMA 6.0.1 fimware 4535de6 amdgpu: Add GC 11.0.1 firmware 2e93e4c amdgpu: Add DCN 3.1.4 firmware 3435843 iwlwifi: remove old intermediate 5.15+ firmwares 494389c iwlwifi: remove 5.10 and 5.15 intermediate old firmwares 177c593 iwlwifi: remove 5.4 and 5.10 intermediate old firmwares fa3a6d5 iwlwifi: remove 4.19 and 5.4 intermediate old firmwares d11eb6f iwlwifi: remove old unsupported older than 4.14 LTS bb2d42d linux-firmware: update firmware for MT7921 WiFi device 3f0f338 linux-firmware: update firmware for mediatek bluetooth chip (MT7921) f88f1f8 amdgpu: update vangogh firmware Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq807x: add support for Netgear WAX218Alexandru Gagniuc2023-03-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall or ceiling mountable. It can be powered via PoE, or a 12 V adapter. The board has footprints for 2.54mm UART headers. They're difficult to solder because the GND is connected to a large copper plane. Only try soldering if you are very skilled. Otherwise, use pogo pins. Specifications: --------------- * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 366 MB of RAM available to OS, not sure of total amount * Storage: Macronix MX30UF2G18AC 256MB NAND * Ethernet: * 2.5G RJ45 port (QCA8081) with PoE input * WLAN: * 2.4GHz/5GHz with 8 antennas * LEDs: * Power (Amber) * LAN (Blue) * 2G WLAN (Blue) * 5G WLAN (Blue) * Buttons: * 1x Factory reset * Power: 12V DC Jack * UART: Two 4-pin unpopulated headers near the LEDs * "J2 UART" is the CPU UART, 3.3 V level Installation: ============= Web UI method ------------- Flashing OpenWRT using the vendor's Web UI is problematic on this device. The u-boot mechanism for communicating the active rootfs is antiquated and unreliable. Instead of setting the kernel commandline, it relies on patching the DTS partitions of the nand node. The way partitions are patched is incompatible with newer kernels. Newer kernels use the SMEM partition table, which puts "rootfs" on mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One reliable way to boot from mtd14 and avoid boot loops is to use an initramfs image. 1. In the factory web UI, navigate to System Manager -> Firmware. 2. In the "Local Firmware Upgrade" section, click Browse 3. Navigate and select the 'web-ui-factory.fit' image 4. Click "Upload" 5. On the following page, click on "Proceed" The flash proceeds at this point and the system will reboot automatically to OpenWRT. 6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline SSH method ---------- Enable SSH using the CLI or Web UI. The root account is locked out to ssh, and the admin account defaults to Netgear's CLI application. So we need to get creative: First, make sure the device boots from the second firmware partition: ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 1 Then reboot the device, and run the update: scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \ -o hostkeyalgorithms=ssh-rsa \ netgear_wax218-squashfs-nand-factory.ubi \ admin@<ipaddr>:/tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 0 Now reboot the device, and it should boot into a ready-to-use OpenWRT. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Francisco G Luna <frangonlun@gmail.com>
* ipq-wifi: bump to latest git HEADKristjan Krušič2023-03-191-3/+3
| | | | | | | 31ff96d ipq806x: add support for Nokia Airscale AC400i 1af1df2 ath11k: ipq8074: add Netgear WAX218 Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
* ipq806x: add support for Nokia Airscale AC400iKristjan Krušič2023-03-191-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Qualcomm IPQ8065 RAM: 512 MB DDR3 Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB) 4 MB SPI-NOR (Macronix MX25U3235F) WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz Qualcomm Atheros QCA9984 - 5Ghz ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt) eth1 - (1000Mbps in both) Auto-negotiation broken on both. USB: USB 2.0 LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red) BTN: Reset Other: SD card slot (non-functional) Serial: 115200bps, near the Ethernet transformers, labeled 9X. Connections from the arrow to the 9X text: [NC] - [TXD] - [GND] - [RXD] - [NC] Installation ------------ 0. Connect to the device Plug your computer into LAN2 (1000Mbps connection required). If you use the LAN1/POE port, set your computer to force a 100Mbps link. Connect to the device via TTL (Serial) 115200n8. Locate the header (or solder pads) labeled 9X, near the Ethernet jacks/transformers. There should be an arrow on the other side of the header marking. The connections should go like this: (from the arrow to the 9X text): NC - TXD - GND - RXD - NC 1. Prepare for installation While the AP is powering up, interrupt the startup process. MAKE SURE TO CHECK YOUR CURRENT PARTITION! If you see: "Current Partition is : partB" or "Need to switch partition from partA to partB", you have to force the device into partA mode, before continuing. This can be done by changing the PKRstCnt to 5 and resetting the device. setenv PKRstCnt 5 saveenv reset After you interrupt the startup process again, you should see: Need to switch partition from partB to partA You can now continue to the next step. If you see: "Current Partition is : partA", you can continue to the next step. 2. Prevent partition switching. To prevent the device from switching partitions, we are going to modify the startup command. set bootcmd "setenv PKRstCnt 0; saveenv; bootipq" setenv 3. First boot Now, we have to boot the OpenWrt intifs. The easiest way to do this is by using Tiny PXE. You can also use the normal U-Boot tftp method. Run "bootp" this will get an IP from the DHCP server and possibly the firmware image. If it doesn't download the firmware image, run "tftpboot". Now run "bootm" to run the image. You might see: "ERROR: new format image overwritten - must RESET the board to recover" this means that the image you are trying to load is too big. Use a smaller image for the initial boot. 4. Install OpenWrt from initfs Once you are booted into OpenWrt, transfer the OpenWrt upgrade image and use sysupgrade to install OpenWrt to the device. Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
* ipq-wifi: bump to latest git HEADChristian Marangi2023-03-181-2/+2
| | | | | | 86180c4 ath10k-firmware: IPQ4019 hw1.0: Rename variant to ZTE MF18A specific BDF Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq-wifi: bump to latest git HEADChristian Marangi2023-03-181-3/+3
| | | | | | | 1f35a8c ath10k-firmware: IPQ4019 hw1.0: Add variant to Teltonika RUTX10 specific BDF a49672f ath10k-firmware: QCA99X0 hw2.0: Add variant to ZTE MF18A specific BDF Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq-wifi: bump to latest git HEAD and add 8devices boardsMantas Pucka2023-03-171-3/+7
| | | | | | | | | 2dae618 ipq-wifi: update 8devices Jalapeno BDF 08e92db ipq-wifi: update 8devices Habanero BDF Signed-off-by: Mantas Pucka <mantas@8devices.com> [ split ipq40xx changes in separate commit ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* firmware: ipq-wifi: use project branch and drop local fileChristian Marangi2023-03-1536-5/+8
| | | | | | | Source BDF files out of project dedicated repository and drop local file from openwrt main repository. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* linux-firmware: add mt7986 offload firmwareFelix Fietkau2023-03-021-0/+10
| | | | | | | This is needed for WED support on MT7986. Enable it by default for the filogic subtarget. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* wireless-regdb: update to 2023.02.13Yuu Toriyama2023-02-181-2/+2
| | | | | | | | | | | | Changes: 7f7a9f7 wireless-regdb: update regulatory database based on preceding changes 660a1ae wireless-regdb: Update regulatory info for Russia (RU) on 5GHz fe05cc9 wireless-regdb: Update regulatory rules for Japan (JP) on 6GHz d8584dc wireless-regdb: Update regulatory rules for Japan (JP) on 5GHz c04fd9b wireless-regdb: update regulatory rules for Switzerland (CH) f29772a wireless-regdb: Update regulatory rules for Brazil (BR) Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
* ipq807x: add support for Buffalo WXR-5950AX12INAGAKI Hiroshi2023-02-122-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WXR-5950AX12 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ8074A. Specification: - SoC : Qualcomm IPQ8074A - RAM : DDR3 1024 MiB (2x Nanya NT5CC256M16ER-EK) - Flash : RAW NAND 256 MiB (Winbond W29N02GZBIBA) - WLAN : 2.4/5 GHz (IPQ8074A) - Ethernet : 5 ports - WAN : 100/1000/2500/10000 Mbps x1 (AQR113C) - LAN : 100/1000/2500/10000 Mbps x1 (AQR113C), 10/100/1000 Mbps x3 (QCA8075) - LED/Keys : 8x/5x - UART : pin header on PCB (J7) - assignment: 3.3V, GND, TX, RX from disc marking - settings : 115200n8 - Power : 12 VDC, 4 A Flash instruction using initramfs image: 1. Prepare TFTP server with IP address 192.168.11.10 2. Rename OpenWrt initramfs image to "WXR-5950AX12-initramfs.uImage and place it to TFTP directory 3. Hold AOSS (WPS) button and power on WXR-5950AX12 4. WXR-5950AX12 downloads initramfs image from TFTP server and boots with it automatically 5. Upload sysupgrade image to WXR-5950AX12 and perform sysupgrade 6. Wait ~120 seconds to complete flashing Partition layout: 0x000000000000-0x000000100000 : "0:sbl1" 0x000000100000-0x000000200000 : "0:mibib" 0x000000200000-0x000000280000 : "0:bootconfig" 0x000000280000-0x000000300000 : "0:bootconfig1" 0x000000300000-0x000000600000 : "0:qsee" 0x000000600000-0x000000900000 : "0:qsee_1" 0x000000900000-0x000000980000 : "0:devcfg" 0x000000980000-0x000000a00000 : "0:devcfg_1" 0x000000a00000-0x000000a80000 : "0:apdp" 0x000000a80000-0x000000b00000 : "0:apdp_1" 0x000000b00000-0x000000b80000 : "0:rpm" 0x000000b80000-0x000000c00000 : "0:rpm_1" 0x000000c00000-0x000000c80000 : "0:cdt" 0x000000c80000-0x000000d00000 : "0:cdt_1" 0x000000d00000-0x000000d80000 : "0:appsblenv" 0x000000d80000-0x000000e80000 : "0:appsbl" 0x000000e80000-0x000000f80000 : "0:appsbl_1" 0x000000f80000-0x000001000000 : "0:art" 0x000001000000-0x000001080000 : "0:art_1" 0x000001080000-0x000001100000 : "0:orgdata" 0x000001100000-0x000001180000 : "0:orgdata_1" 0x000001180000-0x000005180000 : "rootfs" 0x000005180000-0x000009180000 : "rootfs_recover" 0x000009180000-0x000010000000 : "user_property" Notes: - WXR-5950AX12 has 2x OS images on NAND flash. The 1st image is for normal operation and the 2nd one is for recoverying or firmware upgrading on stock. - Stock U-Boot checks MD5 hashes in "fw_hash" volume in each "root*" partition when booting. This is just a comparation of hash strings. Behaviors: - both "fw_hash" volumes exist, hashes are rootfs == rootfs_recover ---> boot from rootfs - both "fw_hash" volumes exist, hashes are rootfs != rootfs_recover ---> boot from rootfs_recover Note: this behavior is used for firmware upgrading on stock - "fw_hash" volume in rootfs is missing ---> boot from rootfs_recover - "fw_hash" volume in rootfs_recover is missing ---> boot from rootfs - "fw_hash" volumes in both root* partition are missing ---> boot from rootfs_recover Reverting to stock firmware: 1. Decrypt official image by buffalo-enc and remove header example of decryption: $ buffalo-enc -i wxr_5950ax12_jp_305 -o wxr_5950ax12_jp_305.dec \ -d -k olaffuB -O 0xc8 example of removing header (v3.05): - before $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.dec 00000000 57 58 52 2d 35 39 35 30 41 58 31 32 5f 33 2e 30 |WXR-5950AX12_3.0| 00000010 35 5f 31 2e 30 31 5f 4a 50 5f 6a 70 5f 71 63 61 |5_1.01_JP_jp_qca| 00000020 0a 66 69 6c 65 6c 65 6e 3d 34 35 33 35 30 39 31 |.filelen=4535091| 00000030 32 0a 55 42 49 23 01 00 00 00 00 00 00 00 00 00 |2.UBI#..........| 00000040 - after $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.ubi 00000000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............| 00000010 00 00 08 00 00 00 10 00 78 cf c4 91 00 00 00 00 |........x.......| 00000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000030 00 00 00 00 00 00 00 00 00 00 00 00 3d 2a 64 fd |............=*d.| 00000040 2. Boot WXR-5950AX12 with OpenWrt initramfs image 3. Upload modified stock image to WXR-5950AX12 4. Find partitions "rootfs" and "rootfs_recover" example: root@OpenWrt:/# cat /proc/mtd dev: size erasesize name ... mtd22: 04000000 00020000 "rootfs" mtd23: 04000000 00020000 "rootfs_recover" ... in this case, "rootfs" is mtd22 and "rootfs_recover" is mtd23 5. Format "rootfs"/"rootfs_recover" partition with the uploaded image example: ubiformat /dev/mtd22 -f /tmp/wxr_5950ax12_jp_305.ubi ubiformat /dev/mtd23 -f /tmp/wxr_5950ax12_jp_305.ubi 6. Remove "rootfs"/"rootfs_data" volume from user_property partition example: . /lib/upgrade/nand.sh UBI=$(nand_attach_ubi user_property) ubirmvol /dev/$UBI -N rootfs ubirmvol /dev/$UBI -N rootfs_data 7. Reboot MAC addresses: LAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) WAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) 2.4 GHz: 50:C4:DD:xx:xx:30 (0:APPSBLENV, wlan0addr (text)) 5 GHz : 50:C4:DD:xx:xx:38 (0:APPSBLENV, wlan1addr (text)) Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* linux-firmware: update to 20230117Nick Hainke2023-01-261-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changes: 32d3199 linux-firmware: Update firmware file for Intel Bluetooth AX201 2da8a7a linux-firmware: Update firmware file for Intel Bluetooth AX201 8b5ddf4 linux-firmware: Update firmware file for Intel Bluetooth AX211 4219dac linux-firmware: Update firmware file for Intel Bluetooth AX211 fb34135 linux-firmware: Update firmware file for Intel Bluetooth AX210 becd3fc linux-firmware: Update firmware file for Intel Bluetooth AX200 7101c57 linux-firmware: Update firmware file for Intel Bluetooth AX201 49e87fa linux-firmware: Update firmware file for Intel Bluetooth 9560 86b73ce linux-firmware: Update firmware file for Intel Bluetooth 9260 3723b48 brcm: add configuration files for CyberTan WC121 7f626ef qcom: add firmware files for Adreno A200 fc5a25f rtw89: 8852c: update fw to v0.27.56.10 2ba1bea QCA: Add Bluetooth firmware for QCA2066 a1ad1d5 amdgpu: add VCN4.0.4 firmware from amd-5.4 9e01e17 amdgpu: add SMU13.0.7 firmware from amd-5.4 3a50eb8 amdgpu: add SDMA6.0.2 firmware from amd-5.4 19995fb amdgpu: add PSP13.0.7 firmware from amd-5.4 32e7c93 amdgpu: add GC11.0.2 firmware from amd-5.4 20c8060 amdgpu: add DCN3.2.1 firmware from amd-5.4 5c8e895 amdgpu: update VCN4.0.0 firmware from amd-5.4 66b3435 amdgpu: update SMU13.0.0 firmware from amd-5.4 604df78 amdgpu: update SDMA6.0.0 firmware from amd-5.4 3e9169a amdgpu: update PSP13.0.0 firmware from amd-5.4 bd1b7f7 amdgpu: update GC11.0.0 firmware from amd-5.4 c8ff1f4 iwlwifi: add new FWs from core76-35 release 5630963 iwlwifi: update cc/Qu/QuZ firmwares for core76-35 release 8bbec22 iwlwifi: add new FWs from core75-47 release e20a687 iwlwifi: update 9000-family firmwares to core75-47 504b691 amdgpu: update renoir DMCUB firmware 1ed02d5 amdgpu: Update renoir PSP firmware d0598c3 amdgpu: update copyright date for LICENSE.amdgpu cee86df linux-firmware: update firmware for MT7921 WiFi device e2d1174 linux-firmware: update firmware for MT7922 WiFi device ce7cc73 linux-firmware: update firmware for mediatek bluetooth chip (MT7921) 91f4c6b linux-firmware: update firmware for mediatek bluetooth chip (MT7922) 52e62d6 cxgb4: Update firmware to revision 1.27.1.0 4704e25 qca: Update firmware files for BT chip WCN6750 c9c1958 rtw89: 8852c: update fw to v0.27.56.9 9e91f0c rtw89: 8852c: update fw to v0.27.56.8 Signed-off-by: Nick Hainke <vincent@systemli.org>
* firmware: intel-microcode: update to 20221108Linhui Liu2023-01-261-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changelog: * New Microcodes: sig 0x000606c1, pf_mask 0x10, 2022-08-07, rev 0x1000201, size 286720 sig 0x000b0671, pf_mask 0x32, 2022-09-07, rev 0x010e, size 204800 * Updated Microcodes: sig 0x000706e5, pf_mask 0x80, 2022-08-02, rev 0x00b6, size 113664 sig 0x000806c1, pf_mask 0x80, 2022-06-28, rev 0x00a6, size 110592 sig 0x000806d1, pf_mask 0xc2, 2022-06-28, rev 0x0042, size 102400 sig 0x000806ec, pf_mask 0x94, 2022-07-31, rev 0x00f4, size 105472 sig 0x00090661, pf_mask 0x01, 2022-07-15, rev 0x0017, size 20480 sig 0x00090672, pf_mask 0x07, 2022-09-19, rev 0x0026, size 218112 sig 0x00090675, pf_mask 0x07, 2022-09-19, rev 0x0026 sig 0x000b06f2, pf_mask 0x07, 2022-09-19, rev 0x0026 sig 0x000b06f5, pf_mask 0x07, 2022-09-19, rev 0x0026 sig 0x000906a3, pf_mask 0x80, 2022-09-19, rev 0x0424, size 217088 sig 0x000906a4, pf_mask 0x80, 2022-09-19, rev 0x0424 sig 0x000906ed, pf_mask 0x22, 2022-07-31, rev 0x00f4, size 104448 sig 0x000a0652, pf_mask 0x20, 2022-07-31, rev 0x00f4, size 96256 sig 0x000a0653, pf_mask 0x22, 2022-07-31, rev 0x00f4, size 97280 sig 0x000a0655, pf_mask 0x22, 2022-07-31, rev 0x00f4, size 96256 sig 0x000a0660, pf_mask 0x80, 2022-07-31, rev 0x00f4, size 97280 sig 0x000a0661, pf_mask 0x80, 2022-07-31, rev 0x00f4, size 96256 sig 0x000a0671, pf_mask 0x02, 2022-08-02, rev 0x0056, size 103424 We need to update to this version because https://ftp.debian.org/debian/pool/non-free/i/intel-microcode/intel-microcode_3.20220809.1.tar.xz has been removed. Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
* ipq807x: Add ZyXEL NBG7815André Valentin2023-01-192-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1 GB 2x Nanya NT5CC256M16ER-EK * Storage: * 8MB serial flash Winbond W25Q64DW * 4GB eMMC flash Kingston EMMC04G-M627 * Ethernet: * 4x1G RJ45 ports (QCA8074A) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * 1x10G RJ45 port (AQR113C) with 1x status LED * Switch: Qualcomm Atheros QCA8075 * WLAN: * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate * Bluetooth CSR8811 using HSUART, currently unsupported * USB: 1x USB3.0 Type-A port * LED-s currently not supported: * White * Dark Blu * Amber * Purple * Purple and dark blue * Red * Buttons: * 1x Soft reset * Power: 12V DC Jack Installation instructions: * Disconnect WAN * Reset device to factory defaults by pushing reset button 15 sec, LEDs should lit orange color. * After 5-10 minutes, when the LEDs turn constant dark blue, put your LAN cable and connect at address 192.168.123.1 by telnet on port 23 * Login with NBG7815 login: root password: nbg7815@2019 * cd /tmp/ApplicationData * wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://... * wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh * run flash_to_openwrt.sh If you can't use wget, you can transfer the files via nc. See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details. Bluetooth usage: * you need at least package bluez-utils, recommended bluez-daemon * run following commands to enable and start hciattach /dev/ttyMSM1 bcsp hciconfig hci0 up Many thanks to itorK for his work on this device: https://github.com/itorK/openwrt/tree/nbg7815 Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: André Valentin <avalentin@marcant.net>
* ipq807x: add Dynalink DL-WRX36Dirk Buchwalder2023-01-162-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 256MB Nand • Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081) • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate • 1x USB 3.0 • 1 gpio-controlled dual color led (blue/red) • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard (J1004) the connector size is a 4-pin 2.0 mm JST PH. RX/TX is working, u-boot bootwait is active, secure boot is enabled. Notes: - Serial is completely deactivated in the stock firmware image. - This commit adds only single partition support, that means sysupgrade is upgrading the current rootfs partition. - Installation can be done by serial connection or SSH access on OEM firmware Installation Instructions: Most part of the installation is performed from an initramfs image running OpenWrt, and there are two options to boot it. Boot initramfs option 1: Using serial connection (3.3V) 1. Stop auto boot to get to U-boot shell 2. Transfer initramfs image to device (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb) Tested using TFTP and a FAT-formatted USB flash drive. 3. Boot the initramfs image # bootm Boot initramfs option 2: From SSH access on OEM firmware 1. Copy the initramfs image to a FAT-formatted flash drive (tested on single-partition drive) and connect it to device USB port. 2. Change boot command so it loads the initramfs image on next boot Fallback to OEM firmware is provided. # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq' 3. Reboot the device to boot the initramfs # reboot Install OpenWrt from initramfs image: 1. Use SCP (or other way) to transfer OpenWrt factory image 2. Connect to device using SSH (on a LAN port) 3. Check MTD partition table. rootfs and rootfs_1 should be mtd18 and mtd20 depending on current OEM slot. # cat /proc/mtd 4. Do a ubiformat to both rootfs partitions: # ubiformat /dev/mtd18 -y -f /path_to/factory_image # ubiformat /dev/mtd20 -y -f /path_to/factory_image 5. Set U-boot env variable: mtdids # fw_setenv mtdids 'nand0=nand0' 6. Get offset of mtd18 to determine current OEM slot - If current OEM slot is 1, offset is 16777216 (0x1000000) - If current OEM slot is 2, offset is 127926272 (0x7a00000) # cat /sys/class/mtd/mtd18/offset 7. Set U-boot env variable: mtdparts If current OEM slot is 1, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)' If current OEM slot is 2, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)' 8. Set U-boot env variable: bootcmd # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0' 9. Reboot the device # reboot Note: this PR adds only single partition support, that means sysupgrade is upgrading the current rootfs partition Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
* ipq807x: add Edgecore EAP102Matthew Hagan2023-01-162-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be powered by either PoE or AC adapter. Device info: - IPQ8071-A SoC - 1GiB RAM - 256MiB NAND flash - 32MiB SPI NOR - 2 Ethernet ports - 1 Console port - 2GHz/5GHz AX WLAN - 2 USB 2.0 ports Install instructions: Prerequistes - TFTP server, preferrably within 192.168.1.0/24 Console cable plugged in (115200 8N1 no flow control) 1. Power on device and interrupt u-boot to obtain u-boot CLI 2. set serverip to IP address of the TFTP server: `setenv serverip 192.168.1.250` 3. Download image from TFTP server: `tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi` 4. Flash ubi image to both partitions and reset: `sf probe imxtract 0x44000000 ubi nand device 0 nand erase 0x0 0x3400000 nand erase 0x3c00000 0x3400000 nand write $fileaddr 0x0 $filesize nand write $fileaddr 0x3c00000 $filesize reset` Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq807x: Add Xiaomi AX9000Robert Marko2023-01-164-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq807x: add QNAP 301wDirk Buchwalder2023-01-162-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR (contains art and u-boot-env) • Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C) • WLAN: 2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate • LEDs: 7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, hold WPS button til the second beep (yes the router has a buzzer) SSH is available on port 22200, login with user admin and password "mac address of the router". Installation Instructions: • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial) • stop auto boot • setenv serverip 192.168.10.1 • setenv ipaddr 192.168.10.10 • tftpboot the initramfs image (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb) • bootm • make sure that current_entry is set to "0": "fw_printenv -n current_entry" should be print "0". If not, do "fw_setenv current_entry 0" • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin to the device to /tmp folder • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4) • reboot Note: this leaves the second kernel / rootfs parition untouched. So if you want to go back to stock, stop u-boot autoboot, "setenv current_entry 1" , "saveenv", "bootipq". Stock firmware should start from the second partition. Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt in the first partitions Make 10G Aquantia phy's work: The aquantia phy's need a firmware to work. This can either be loaded in linux with a userspace tool or in u-boot. I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is aq_load_fw available in u-boot. But first the right firmware needs to write to the 0:ETHPHYFW mtd partition (it is empty on my device) Grab the ethphy firmware image from: https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn and scp that to openwrt. Check the 0:ETHPHYFW partition number: cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10. Backup the 0:ETHPHYFW partition: dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place. Write the new firmware image to the 0:ETHPHYFW partition: "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10". Reboot to u-boot. Check if aq_load_fw is working: "aq_load_fw 0", that checks the firmware and if successfull, loads iram and dram to one of the aquantia phy's. If that worked, add the aq_load_fw to the bootcmd: setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq" "saveenv" "reset" Board reboots and the firmware load to both phy's should start and then openwrt boots. Check if the 10G ports work. Note: lan port labeled "10G-2" is configured as WAN port as per default. All other port are in the br-lan. This can be changed in the network config. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
* ipq807x: add Edimax CAX1800Dirk Buchwalder2023-01-162-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Edimax CAX1800 is a 802.11 ax dual-band AP with PoE. AP can be ceiling or wall mount. Specifications: • CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz • RAM: 512MB of DDR3 • Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env) • Ethernet: 1x 1G RJ45 port (QCA8072) PoE • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate 5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate • LEDs: 3 x GPIO-controlled System-LEDs (form one virtual RGB System-LED) black_small_square Buttons: 1x soft reset black_small_square Power: 12V DC jack or PoE (802.3af ) An unpopulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, but it drops only to a limited shell . Installation Instructions: black_small_square obtain serial access black_small_square stop auto boot black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot) black_small_square bootm black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi to the device black_small_square write the image to the NAND: black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0) black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs- nand-factory.ubi black_small_square reboot Note: Device is not using dual partitioning (NAND contains other partitions with different manufacture data etc.) Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
* ipq807x: add Redmi AX6Zhijun You2023-01-162-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Redmi AX6 is a budget 802.11ax dual-band router/AP Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 128MB NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LEDs: * System (Blue/Yellow) * Network (Blue/Yellow) *Buttons: 1x soft reset *Power: 12V DC jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Zhijun You <hujy652@gmail.com>
* ipq807x: add Xiaomi AX3600Robert Marko2023-01-163-3/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
* firmware: add ath11k-firmware packageRobert Marko2023-01-161-0/+66
| | | | | | | | | | Package ath11k firmware for AHB devices as well as QCN9074 which is a non consumer card targeted as a companion for QCA WiSoC-s. linux-firmware is always out of date for these, so fetch them from Kalle-s repo like we do for ath10k. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: add support for Linksys WHW03 V2Vincent Tremblay2023-01-153-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA8888 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash 1: Mactronix MX30LF4G18AC-XKI RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB) LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). - The three WiFis were fully tested and are configured with the same settings as in the vendor firmware. - The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream. - Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working. Bluetooth: ======== - Fully working with the following caveats: - RFKILL need to be enabled in the kernel. - An older version of bluez is needed as bccmd is needed to configure the chip. Zigbee: ====== - The spidev device is available in the /dev directory. - GPIOs are configured the same way as in the vendor firmware. - Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working. Installation: ========= The squash-factory image can be installed via the Linksys Web UI: 1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device). 2. Login with your admin password. 3. To enter into the support mode, click on the "CA" link and the bottom of the page. 4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button. 5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups. The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts. If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row. It can also be done via TFTP: 1. Setup a local TFTP server and configure its IP to 192.168.1.100. 2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server. 3. Connect to the device through the serial console. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2". 6. Once flashed, enter "reset" to reboot the device. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
* ipq40xx: Add support ZTE MF18AMarcin Gajda2023-01-143-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
* linux-firmware: disable strippingRobert Marko2022-12-291-1/+4
| | | | | | | | | | | It has been brought to my attention that recently added WCN6855 firmware is broken as it is getting stripped during building due to being 2 ELF binaries. I am sure WCN6750 and any other ELF binaries are having the same issue, so since stripping firmware binaries is clearly unwanted disable it. Fixes: b4d3694f81f4 ("linux-firmware: package ath11k consumer cards firmware") Signed-off-by: Robert Marko <robimarko@gmail.com>
* linux-firmware: ath11k: add symlink for WCN6855 hw2.1Robert Marko2022-12-282-1/+2
| | | | | | | | WCN6855 exists in 2 HW revisions, but both use the same FW so upstream just has a symlink for hw2.1 to hw2.0 that I forgot to make. Fixes: b4d3694f81f4 ("linux-firmware: package ath11k consumer cards firmware") Signed-off-by: Robert Marko <robimarko@gmail.com>
* linux-firmware: update to 20221214Nick Hainke2022-12-281-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changes: f3c283e amdgpu: updated navi10 firmware for amd-5.4 ba115d4 amdgpu: updated yellow carp firmware for amd-5.4 b8aba70 amdgpu: updated raven2 firmware for amd-5.4 2b21c5e amdgpu: updated raven firmware for amd-5.4 fc9a1c9 amdgpu: updated PSP 13.0.8 firmware for amd-5.4 7d43336 amdgpu: updated GC 10.3.7 RLC firmware for amd-5.4 c089dab amdgpu: updated vega20 firmware for amd-5.4 75e3494 amdgpu: updated PSP 13.0.5 firmware for amd-5.4 31c5734 amdgpu: add VCN 4.0.0 firmware for amd-5.4 a735158 amdgpu: add SMU 13.0.0 firmware for amd-5.4 0bef6bb amdgpu: Add SDMA 6.0.0 firmware for amd-5.4 bb56d1a amdgpu: add PSP 13.0.0 firmware for amd-5.4 e32209f amdgpu: add GC 11.0.0 firmware for amd-5.4 613db81 amdgpu: add DCN 3.2.0 firmware for amd-5.4 1fc8f6c amdgpu: updated vega10 firmware for amd-5.4 2257447 amdgpu: updated beige goby firmware for amd-5.4 6aa0023 amdgpu: updated dimgrey cavefish firmware for amd-5.4 dd1225a amdgpu: updated vangogh firmware for amd-5.4 5cb010e amdgpu: updated picasso firmware for amd-5.4 edf9699 amdgpu: updated navy flounder firmware for amd-5.4 b7e83d9 amdgpu: updated green sardine firmware for amd-5.4 f820cc3 amdgpu: updated sienna cichlid firmware for amd-5.4 b77f539 amdgpu: updated arcture firmware for amd-5.4 dccfdf1 amdgpu: updated navi14 firmware for amd-5.4 5d1af6d amdgpu: updated renoir firmware for amd-5.4 13b9c94 amdgpu: updated navi12 firmware for amd-5.4 e9b8357 amdgpu: updated aldebaran firmware for amd-5.4 b4af754 sr150 : Add NXP SR150 UWB firmware 0707b2f brcm: add/update firmware files for brcmfmac driver 16c9630 rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x75b8_f098 80ed874 amdgpu: update sdma_5.2.7 firmware 32d8681 QCA: Add Bluetooth firmware for WCN785x This commit will add required Bluetooth firmware files for QCA WCN785x. The image version is 2.0.0-00515. cdf9499 linux-firmware: update firmware for MT7916 685ea4d linux-firmware: update firmware for MT7915 7f6279b i915: Add DMC v2.08 for DG2 391fb47 amdgpu: update green sardine DMCUB firmware de854c9 i915: Add DMC v2.10 for MTL daff404 linux-firmware: update firmware for MT7986 70494e3 linux-firmware: update firmware for mediatek bluetooth chip (MT7921) 750c0dc linux-firmware: update firmware for MT7921 WiFi device Signed-off-by: Nick Hainke <vincent@systemli.org>
* linux-firmware: package ath11k consumer cards firmwareRobert Marko2022-12-192-1/+24
| | | | | | Package firmware for ath11k supported QCA consumer cards from linux-firmware. Signed-off-by: Robert Marko <robimarko@gmail.com>
* cypress-firmware: update to v5.10.9-2022_0909Álvaro Fernández Rojas2022-11-171-3/+147
| | | | | | | | | | | | | | | | | | | | | | | | | The following firmwares have been updated: - cyfmac43012-sdio (v13.10.271.266 -> v13.10.271.289) - cyfmac43430-sdio (v7.45.98.118 -> v7.45.98.125) - cyfmac43455-sdio (v7.45.234 -> v7.45.250) - cyfmac4354-sdio (v7.35.349.104 -> v7.35.349.117) - cyfmac4356-pcie (v7.35.180.208 -> v7.35.180.212) - cyfmac4356-sdio (v7.35.349.104 -> v7.35.349.115) - cyfmac4373-sdio (v13.10.246.253 -> v13.10.246.289) - cyfmac4373-usb (v13.10.246.253 -> v13.10.246.289) - cyfmac54591-pcie (v13.35.225 -> v13.35.284) The following firmwares have been added: - cyfmac43439-sdio (v7.95.55) - cyfmac4373-pcie (v13.35.205.66) - cyfmac54591-sdio (v13.35.284) - cyfmac55560-pcie (v18.53.53.4) - cyfmac55572-pcie (v18.53.117.2) - cyfmac55572-sdio (v18.53.117.2) More info: https://github.com/Infineon/ifx-linux-firmware/compare/release-v5.4.18-2021_0812...release-v5.10.9-2022_0909 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* cypress-firmware: fix cyfmac4356-pcie symbolic linksÁlvaro Fernández Rojas2022-11-171-9/+4
| | | | | | | The symbolic link introduced in 22e9d8bc896b is wrong. Fixes: 22e9d8bc896b ("cypress-firmware: use symlink to provide firmware in brcm") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* cypress-nvram: consolidate NVRAM packagesKuan-Yi Li2022-11-161-20/+6
| | | | | | | NVRAM packages for the same wireless chip are consolidated into one as they contain only small text files and symlinks. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* linux-firmware: broadcom: consolidate NVRAM packagesKuan-Yi Li2022-11-163-31/+79
| | | | | | | NVRAM packages for the same wireless chip are consolidated into one as they contain only small text files and symlinks. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* cypress-nvram: disassociate from external source repoKuan-Yi Li2022-11-162-101/+18
| | | | | | | | | | | | Since all NVRAM files in external repo are now upstreamed and to lower future maintenance cost, disassociate the package from external source repo. All upstream pending NVRAM files shall be stored locally from now on. Signed-off-by: Kuan-Yi Li <kyli@abysm.org> [Remove outdated URL, add SPDX-License-Identifier] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* linux-firmware: offer two versions of firmware for CYW4339Kuan-Yi Li2022-11-154-10/+36
| | | | | | | | | | | | | | | | | | | | | According to commit 6f6c2fb321, AP6335 module used in PICO-PI-IMX7D works only with firmware from `linux-firmware`. However, firmware from `cypress-firmware` suite is directly from the chip company (Infineon) and is actually newer. Instead of dropping the firmware from Infineon, create a package named `brcmfmac-firmware-4339-sdio`, and keep the Infineon version of `cypress-firmware-4339-sdio` around. This gives us devs the option to choose. Also, it means that - packages `brcmfmac-firmware-*` uniformly come from `linux-firmware` - packages `cypress-firmware-*` uniformly come from `cypress-firmware` so hopefully brings more clarity. Tested-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* linux-firmware: broadcom: use symlink to provide NVRAM for some RPisKuan-Yi Li2022-11-152-4/+13
| | | | | | | | | | This is to align the implementation with upstream `linux-firmware`. Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware` source repository, their NVRAM is provided through a symbolic link to NVRAM of another board with an identical wireless design. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* cypress-firmware: use symlink to provide firmware in brcmKuan-Yi Li2022-11-151-23/+101
| | | | | | | | | | | | | This is to align the implementation with upstream `linux-firmware`. Instead of moving these firmware files to `brcm` subdirectory and changing their names, leave them in `cypress` subdirectory, keep their names intact and use symbolic links to provide compatibility with Broadcom FullMAC driver. This gives more context to where the firmware comes from. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* cypress-nvram: use symlink to provide NVRAM for some RPisKuan-Yi Li2022-11-151-11/+25
| | | | | | | | | | This is to align the implementation with upstream `linux-firmware`. Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware` source repository, their NVRAM is provided through a symbolic link to NVRAM of another board with an identical wireless design. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* cypress-nvram: remove PROVIDES in NVRAM packagesKuan-Yi Li2022-11-151-6/+1
| | | | | | | | | | | | | | | | | | | | PROVIDES for these packages will cause ambiguity and circular dependency in planned changes. For example, if there is a package `brcmfmac-firmware-43455-sdio-rpi-cm4` that depends on `brcmfmac-firmware-43455-sdio-rpi-4b`, there is no way to tell which one of below packages the system will go for. - package named `brcmfmac-firmware-43455-sdio-rpi-4b` - package named `cypress-nvram-43455-sdio-rpi-4b` that PROVIDES `brcmfmac-firmware-43455-sdio-rpi-4b` When ambiguity is unacceptable, PROVIDES (aliases) shall be removed and packages shall only be used through their exact name. So remove PROVIDES and keep only CONFLICTS. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* linux-firmware: add rtl8761 bluetooth firmwareQuintin Hill2022-11-121-0/+23
| | | | | | | | | Realtek bluetooth devices need firmware. Add packages for some of these. Tested on a WNDR3700v4 with rtl8761bu firmware. Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
* linux-firmware: update to 20221109Nick Hainke2022-11-121-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changes: 712460c linux-firmware: Update firmware file for Intel Bluetooth 9462 90d5f7e linux-firmware: Update firmware file for Intel Bluetooth 9462 48954ba linux-firmware: Update firmware file for Intel Bluetooth 9560 0e205fd linux-firmware: Update firmware file for Intel Bluetooth 9560 06b941e linux-firmware: Update firmware file for Intel Bluetooth AX201 ba958ff linux-firmware: Update firmware file for Intel Bluetooth AX201 02bdea2 linux-firmware: Update firmware file for Intel Bluetooth AX211 7044d46 linux-firmware: Update firmware file for Intel Bluetooth AX211 1b99bcd linux-firmware: Update firmware file for Intel Bluetooth AX210 4668ae9 linux-firmware: Update firmware file for Intel Bluetooth AX200 5bdfdba linux-firmware: Update firmware file for Intel Bluetooth AX201 b0f995c amdgpu: update DMCUB firmware for DCN 3.1.6 d991031 rtl_bt: Update RTL8822C BT UART firmware to 0xFFB8_ABD6 fd62f01 rtl_bt: Update RTL8822C BT USB firmware to 0xFFB8_ABD3 b15fc21 WHENCE: mrvl: prestera: Add WHENCE entries for newly updated 4.1 FW images bf5a337 mrvl: prestera: Update Marvell Prestera Switchdev FW to v4.1 4a733c2 iwlwifi: add new FWs from core74_pv-60 release 7d2bb50 qcom: drop split a530_zap firmware file 7d56713 qcom/vpu-1.0: drop split firmware in favour of the mbn file 1431496 qcom/venus-4.2: drop split firmware in favour of the mbn file cf95783 qcom/venus-4.2: replace split firmware with the mbn file 1fe6f49 qcom/venus-1.8: replace split firmware with the mbn file abc0302 linux-firmware: Add firmware for Cirrus CS35L41 on new ASUS Laptop 20d9516 iwlwifi: add new PNVM binaries from core74-44 release 06dbfbc iwlwifi: add new FWs from core69-81 release 05df8e6 qcom: update venus firmware files for VPU-2.0 cd6fcdb qcom: remove split SC7280 venus firmware images 1612706 qcom: update venus firmware file for v5.4 ad9fdba qcom: replace split SC7180 venus firmware images with symlink dae5d46 rtw89: 8852b: update fw to v0.27.32.1 a8e86ec rtlwifi: update firmware for rtl8192eu to v35.7 9aa8db1 rtlwifi: Add firmware v4.0 for RTL8188FU 8f86b5a i915: Add HuC 7.10.3 for DG2 48407ff cnm: update chips&media wave521c firmware. bd31846 brcm: add symlink for Pi Zero 2 W NVRAM file 771968c linux-firmware: Add firmware for Cirrus CS35L41 on ASUS Laptops 6f9620e linux-firmware: Add firmware for Cirrus CS35L41 on Lenovo Laptops 1d18cb9 linux-firmware: Add firmware for Cirrus CS35L41 on HP Laptops e497757 rtw89: 8852b: add initial fw v0.27.32.0 98b5577 iwlwifi: add new FWs from core72-129 release 604026c iwlwifi: update 9000-family firmwares to core72-129 Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: add support for GL.iNet GL-A1300Weiping Yang2022-11-092-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2 USB: 1 x USB 3.0 port Button: 1 x Reset button Switch: 1 x Mode switch LED: 1 x Blue LED + 1 x White LED Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi (IPQ40xx) # nand erase 0 0x8000000 (IPQ40xx) # nand write 0x84000000 0 $filesize By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* mac80211: remove old legacy legacy driversFelix Fietkau2022-11-091-74/+0
| | | | | | | | | | | Get rid of drivers that are either limited to 802.11b/g or don't even support cfg80211/mac80211. Most of these are either limited to boards that we don't even support anymore because of firmware size, or were only used for custom hacks by a really small number of users in the past. Let's get rid of those to reduce the maintenance effort and the number of useless packages Signed-off-by: Felix Fietkau <nbd@nbd.name>
* linux-firmware: update to 20221012Nick Hainke2022-10-221-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Changes: cfbd668 rtl_bt: Update RTL8852C BT USB firmware to 0xD5B8_A40A f49effc amdgpu: update GC 10.3.6 RLC firmware f9a1c7f amdgpu: update GC 10.3.7 RLC firmware eb1e45c amdgpu: update Yellow Carp RLC firmware 88557e1 amdgpu: update Beige Goby RLC firmware 2d3c1f8 amdgpu: update Dimgrey Cavefish RLC firmware d513825 amdgpu: update Navy Flounder RLC firmware c132bef amdgpu: update Sienna Cichlid RLC firmware 675bd6a mediatek: Update mt8195 SOF firmware to v0.4.1 44fa25d qcom: add squashed version of a530 zap shader d2aac63 rtw89: 8852c: update fw to v0.27.56.1 c9a1ddf rtw89: 8852c: update fw to v0.27.56.0 b7d6c9f mediatek: Update mt8186 SCP firmware fdf1a65 linux-firmware: Update AMD cpu microcode 375d450 mediatek: mt8195: Update scp.img to v2.0.11956 daee413 mediatek: Add new mt8195 SOF firmware 213255f mediatek: Update mt8186 SOF firmware to v0.2.1 9f88ec4 linux-firmware: update firmware for mediatek bluetooth chip (MT7922) bb3f948 rtl_bt: Update RTL8852A BT USB firmware to 0xD9B8_8207 6be4c4c linux-firmware: update firmware for mediatek bluetooth chip (MT7921) ea94bda linux-firmware: update firmware for MT7922 WiFi device 9490e8a linux-firmware: update firmware for MT7921 WiFi device e6e48db cxgb4: Update firmware to revision 1.27.0.0 51fff4e i915: Add versionless HuC files for current platforms 067440c i915: Add GuC v70.5.1 for DG1, DG2, TGL and ADL-P 0e8f546 qca: Update firmware files for BT chip WCN3991. 3593bb7 Removing crnv32 Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: Add ZTE MF289FGiammarco Marzano2022-09-243-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA) and Vodafone DE\T-Mobile PL (called GigaCube). Modem is a MiniPCIe-to-USB based on Snapdragon X24, it supports 4CA aggregation. There are currently two hardware revisions, which differ on the 5Ghz radio: AT1 = QCA9984 5Ghz Radio on PCI-E bus AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz Device specification -------------------- SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz: (QCA9984): a/n/ac, 4x4 HW REV AT1 (IPA4019): a/n/ac, 2x2 HW REV AT2 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot Installation ------------ 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial connector GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX (refer to this image: https://ibb.co/31Gngpr). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. Stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock, specially mtd16 (Web UI) and mtd17 (rootFS). Use /tmp as temporary storage and do: WEB PARITION -------------------------------------- cat /dev/mtd16 > /tmp/mtd16.bin scp /tmp/mtd16.bin root@YOURSERVERIP:/ rm /tmp/mtd16.bin ROOT PARITION -------------------------------------- cat /dev/mtd17 > /tmp/mtd17.bin scp /tmp/mtd17.bin root@YOURSERVERIP:/ rm /tmp/mtd17.bin 6. Login via ssh or serial and remove stock partitions (default IP 192.168.0.1): # this can return an error, if ubi was attached before # or rootfs part was erased before. ubiattach -m 17 # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # some devices doesn't have it ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. download and install image via sysupgrade -n (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin to the device's /tmp directory) sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin Sometimes it could print ubi attach error, but please ignore it if process goes forward. Flash Layout NAND: mtd8: 000a0000 00020000 "fota-flag" mtd9: 00080000 00020000 "0:ART" mtd10: 00080000 00020000 "mac" mtd11: 000c0000 00020000 "reserved2" mtd12: 00400000 00020000 "cfg-param" mtd13: 00400000 00020000 "log" mtd14: 000a0000 00020000 "oops" mtd15: 00500000 00020000 "reserved3" mtd16: 00800000 00020000 "web" mtd17: 01d00000 00020000 "rootfs" mtd18: 01900000 00020000 "data" mtd19: 03200000 00020000 "fota" mtd20: 0041e000 0001f000 "kernel" mtd21: 0101b000 0001f000 "ubi_rootfs" SPI: mtd0: 00040000 00010000 "0:SBL1" mtd1: 00020000 00010000 "0:MIBIB" mtd2: 00060000 00010000 "0:QSEE" mtd3: 00010000 00010000 "0:CDT" mtd4: 00010000 00010000 "0:DDRPARAMS" mtd5: 00010000 00010000 "0:APPSBLENV" mtd6: 000c0000 00010000 "0:APPSBL" mtd7: 00050000 00010000 "0:reserved1" Back to Stock (!!! need original dump taken from initramfs !!!) ------------- 1. Place mtd16.bin and mtd17.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial console connector (refer to the pin-out from above). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s 5. Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase RootFS+Web: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 ${dir}root_uImage_s nand erase 0x1800000 0x1D00000 nand write $fileaddr 0x1800000 $filesize This will restore Web Interface: tftpboot 0x84000000 ${dir}web.img nand erase 0x1000000 0x800000 nand write $fileaddr 0x1000000 $filesize After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router Signed-off-by: Giammarco Marzano <stich86@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com> (Warning: commit message did not conform to UTF-8 - hopefully fixed?, added description of the pin-out if image goes down, reformatted commit message to be hopefully somewhat readable on git-web, redid some of the gpio-buttons & leds DT nodes, etc.) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 01:45:26 +0000