aboutsummaryrefslogtreecommitdiffstats
path: root/package/firmware
Commit message (Collapse)AuthorAgeFilesLines
* ipq-wifi: Work around Plasma Cloud PA1200 5GHz crashSven Eckelmann2021-09-231-0/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It was noticed [1] that the ath10k firmware crashes on 5GHz since OpenWrt 21.02.0. The problem seems to be triggered by the the nonLinearTxFir field in the 5GHz BDF. If baseEepHeader.nonLinearTxFir (offset 0xc2) is 1 then the firmware just crashes when setting up the 5Ghz radio using `ifconfig wlan1 up`: ath10k_ahb a800000.wifi: firmware crashed! (guid 9e36ee82-4d2c-4c63-b20b-609a1eaca30c) ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 ath10k_ahb a800000.wifi: firmware ver 10.4-3.6-00140 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 ba79b746 ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17 crc32 5f400efc ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1 ath10k_ahb a800000.wifi: firmware register dump: ath10k_ahb a800000.wifi: [00]: 0x0000000B 0x000015B3 0x009C3C27 0x00975B31 ath10k_ahb a800000.wifi: [04]: 0x009C3C27 0x00060530 0x00000018 0x004176B8 ath10k_ahb a800000.wifi: [08]: 0x00405A50 0x00412A30 0x00000000 0x00000000 ath10k_ahb a800000.wifi: [12]: 0x00000009 0x00000000 0x009B9742 0x009B974F ath10k_ahb a800000.wifi: [16]: 0x00971238 0x009B9742 0x00000000 0x00000000 ath10k_ahb a800000.wifi: [20]: 0x409C3C27 0x004053DC 0x00000D2C 0x00405A60 ath10k_ahb a800000.wifi: [24]: 0x809C3E13 0x0040543C 0x00000000 0xC09C3C27 ath10k_ahb a800000.wifi: [28]: 0x809B9AC5 0x0040547C 0x00412A30 0x0040549C ath10k_ahb a800000.wifi: [32]: 0x809B8ECD 0x0040549C 0x00000001 0x00412A30 ath10k_ahb a800000.wifi: [36]: 0x809B8FF3 0x004054CC 0x00412838 0x00000014 ath10k_ahb a800000.wifi: [40]: 0x809BEF98 0x0040551C 0x0041627C 0x00000002 ath10k_ahb a800000.wifi: [44]: 0x80986D47 0x0040553C 0x0041627C 0x00416A88 ath10k_ahb a800000.wifi: [48]: 0x809CBB0A 0x0040559C 0x0041ACC0 0x00000000 ath10k_ahb a800000.wifi: [52]: 0x809864EE 0x0040560C 0x0041ACC0 0x00000001 ath10k_ahb a800000.wifi: [56]: 0x809CA8A4 0x0040564C 0x0041ACC0 0x00000001 ath10k_ahb a800000.wifi: Copy Engine register dump: ath10k_ahb a800000.wifi: [00]: 0x0004a000 14 14 3 3 ath10k_ahb a800000.wifi: [01]: 0x0004a400 16 16 22 23 ath10k_ahb a800000.wifi: [02]: 0x0004a800 3 3 2 3 ath10k_ahb a800000.wifi: [03]: 0x0004ac00 15 15 15 15 ath10k_ahb a800000.wifi: [04]: 0x0004b000 4 4 44 4 ath10k_ahb a800000.wifi: [05]: 0x0004b400 3 3 2 3 ath10k_ahb a800000.wifi: [06]: 0x0004b800 1 1 1 1 ath10k_ahb a800000.wifi: [07]: 0x0004bc00 1 1 1 1 ath10k_ahb a800000.wifi: [08]: 0x0004c000 0 0 127 0 ath10k_ahb a800000.wifi: [09]: 0x0004c400 0 0 0 0 ath10k_ahb a800000.wifi: [10]: 0x0004c800 0 0 0 0 ath10k_ahb a800000.wifi: [11]: 0x0004cc00 0 0 0 0 ath10k_ahb a800000.wifi: failed to update channel list: -108 ath10k_ahb a800000.wifi: failed to set pdev regdomain: -108 ath10k_ahb a800000.wifi: failed to create WMI vdev 0: -108 ieee80211 phy1: Hardware restart was requested Since no actual solution is known (besides downgrading the ath10k firmware) it seems to be better to disable the nonLinearTxFir for now. [1] https://lore.kernel.org/ath10k/3423718.UToCqzeSYe@ripper/ Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq-wifi: Update Plasma Cloud PA1200 BDFs to firmware 3.5.12Sven Eckelmann2021-09-231-0/+0
| | | | | | | | The official Plasma Cloud firmware adjusted the BDFs to contain new conformance test limits and target power values. These should be imported to avoid emissions outside the allowed limits. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq-wifi: Drop empty wifi package for Netgear WAC510Sven Eckelmann2021-09-121-2/+0
| | | | | | | | | | The ipq-wifi-netgear_wac510 package is not selected by any device and would be empty anyway. The default board-2.bin from ath10k-board-qca4019 is therefore used for this device and the package doesn't provide any visible features. Fixes: b126d9c3a3d3 ("ipq40xx: add netgear wac510 support") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* linux-firmware: add 2G and 5G precal binaries for QCA99X0Damien Mascord2021-07-251-0/+35
| | | | | | | | | | | Some devices (such as Extreme Networks WS-AP3959i-ROW) do not contain precal binaries in ART, and the precal in the cards eeprom causes firmware load errors. These firmware files were previously in linux-firmware, so these are adding them back and renaming to be cleaner. Signed-off-by: Damien Mascord <tusker@tusker.org>
* linux-firmware: update to 20210511Tomas Lara2021-06-081-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git log --pretty=oneline --abbrev-commit 20201118..20210511 7685cf4 (HEAD, tag: 20210511) nvidia: Update Tegra194 XUSB firmware to v60.09 cf32752 nvidia: Update Tegra186 XUSB firmware to v55.18 cb8ca82 nvidia: Update Tegra210 XUSB firmware to v50.26 f99d6a1 linux-firmware: update firmware for mhdp8546 ecdfcf8 Merge branch 'adlp_dmc_firmware' of git://anongit.freedesktop.org/drm/drm-firmware into main 547b202 Merge https://github.com/suraj714/linux-firmware-venus into main 3d32f21 i915: Add ADL-P DMC Support 3f23f51 amdgpu: add new polaris 12 MC firmware a2565bb firmware: nvidia: Add VIC firmware for Tegra194 17ec2a5 qcom: add gpu firmwares for sc7280 b653cf4 Merge https://github.com/pkshih/linux-firmware into main 2a96c08 brcm: Add a link to enable khadas VIM2's WiFi ffc64a2 rtw89: 8852a: update fw to v0.13.8.0 3e3497c rtl_bt: Update RTL8852A BT USB firmware to 0xD9A8_7893 c7b11ed qcom: Add venus firmware files for VPU-2.0 2f4f0f8 rtw89: 8852a: update fw to v0.13.8.0 fa0efef linux-firmware: Update firmware file for Intel Bluetooth AX210 9be3daa linux-firmware: Update firmware file for Intel Bluetooth 9560 687d64a linux-firmware: Update firmware file for Intel Bluetooth 9260 a7f1249 linux-firmware: Update firmware file for Intel Bluetooth AX200 47650a0 linux-firmware: Update firmware file for Intel Bluetooth AX201 195ecf1 linux-firmware: Intel BT 7265: Fix Security Issues 4116d72 linux-firmware: Update firmware file for Intel Bluetooth 8265 ca83c73 qcom: update venus firmware files for v5.4 1334578 Merge branch 'mrvl-prestera' of https://github.com/PLVision/linux-firmware into main 16052e4 mrvl: prestera: Add Marvell Prestera Switchdev firmware 3.0 version bdf929d rtw88: 8822c: Update normal firmware to v9.9.9 0b558e8 brcm: add missing symlink for Pi Zero W NVRAM file cfa004c amdgpu: update arcturus firmware from 21.10 d5567c5 amdgpu: update navy flounder firmware from 21.10 ef5ea5d amdgpu: update sienna cichlid firmware from 21.10 f35700f amdgpu: update vega20 firmware from 21.10 1be98f1 amdgpu: update picasso firmware from 21.10 fee0497 amdgpu: update navi14 firmware from 21.10 15003b0 amdgpu: update green sardine firmware from 21.10 64555fb amdgpu: update vega12 firmware from 21.10 eb07276 amdgpu: update navi12 firmware from 21.10 e36c82a amdgpu: update vega10 firmware from 21.10 4a5eaa2 amdgpu: update renoir firmware from 21.10 65eb326 amdgpu: update navi10 firmware from 21.10 8bdca03 amdgpu: update raven2 firmware from 21.10 c9e44ca amdgpu: update raven firmware from 21.10 bc3e610 rtl_nic: add new firmware for RTL8153 and RTL8156 series 8528618 Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware into main 940b7f4 cxgb4: Update firmware to revision 1.25.4.0 f66adc3 Merge branch 'main' of gitolite.kernel.org:/pub/scm/linux/kernel/git/maks/linux-firmware into main f350e91 Merge https://github.com/rjliao-qca/qca-btfw into main 9bc1bcc Merge https://github.com/Netronome/linux-firmware into main 2f30708 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2438 393f272 brcm: Link CM4's WiFi firmware with DMI machine name. 73144e0 linux-firmware: Update firmware file for Intel Bluetooth AX201 8ab7aba amdgpu: update navi14 smc firmware 4fe6e53 amdgpu: update navi10 SMC firmware c296849 QCA: Update Bluetooth firmware for QCA6174 d6a18e9 WHENCE: link to similar config file for rtl8821a support 6c419ae nfp: update Agilio SmartNIC flower firmware to rev AOTC-2.14.A.6 af1ca28 amdgpu: add arcturus firmware 0dd245d Merge branch 'sm8250-new-fw' of https://github.com/lumag/linux-firmware into main 55cab07 rtl_bt: Add rtl8723bs_config-OBDA0623.bin symlink 2548d06 brcm: Add nvram for the Chuwi Hi8 (CWI509) tablet e45c137 brcm: Add nvram for the Predia Basic tablet d8fa0cf qcom: sm8250: update remoteproc firmware 84af0e0 qcom: update a650 firmware files 3f026a2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x59A_76A3 c82cb46 amdgpu: update sienna cichlid firmware for 20.50 24fe696 amdgpu: update vega20 firmware for 20.50 e05d197 amdgpu: update picasso firmware for 20.50 76d07cd amdgpu: update navi14 firmware for 20.50 b2fc037 amdgpu: update vega12 firmware for 20.50 25451a4 amdgpu: update navi12 firmware for 20.50 b938597 amdgpu: update vega10 firmware for 20.50 2542ba7 amdgpu: update renoir firmware for 20.50 b55d063 amdgpu: update navi10 firmware for 20.50 1a62f28 amdgpu: update raven2 firmware for 20.50 4df488f amdgpu: update raven firmware for 20.50 a29bdb2 amdgpu: add initial support for navy flounder 3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210 9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200 c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201 5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6 5a2fd63 iwlwifi: add new FWs from core59-66 release 4f54906 iwlwifi: update 9000-family firmwares 11b7607 iwlwifi: update 7265D firmware e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main 5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406 58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921) e576a1b rtw89: 8852a: add firmware v0.9.12.2 048a7cb WHENCE: add missing symlink for BananaPi M3 aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config 58825f7 brcm: Fix Raspberry Pi 4B NVRAM file 520f71b silabs: add new firmware for WF200 f7915a0 amdgpu: add initial firmware for green sardine 80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5 b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main 66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304 391fd50 linux-firmware: add firmware for MT7921 c5e3240 rtw88: RTL8821C: Update firmware to v24.8 d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210 3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200 13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201 348d8a9 i915: Add DMC v2.01 for ADL-S f33f1f7 i915: Add HuC v7.7.1 for DG1 6a422f5 i915: Add GuC v49.0.1 for DG1 df822a8 qcom: Add venus firmware files for VPU-1.0 11a1db1 qcom: Add SM8250 Compute DSP firmware e55248b qcom: Add SM8250 Audio DSP firmware da74cc6 qcom: add firmware files for Adreno a650 0578970 brcm: Link RPi4's WiFi firmware with DMI machine name. d528862 brcm: Add NVRAM for Vamrs 96boards Rock960 870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes a28a590 cypress: Fix link direction 060ad8b cypress: Link the new cypress firmware to the old brcm files 0f0aefd brcm: remove old brcm firmwares that have newer cypress variants f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB 7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253 e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644 646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work 28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210 23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200 2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201 94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560 27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260 5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main 63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge 0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6 1a08ec9 QCA : Updated firmware files for WCN3991 7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main 7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210 5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210 c487f7d i915: Add GuC firmware v49.0.1 for all platforms d9ffb07 i915: Remove duplicate KBL DMC entry b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018 bc9cd0b linux-firmware: Update AMD SEV firmware 54c797a amdgpu: add sienna cichlid firmware for 20.45 1340e9c amdgpu: update vega20 firmware for 20.45 b260c9c amdgpu: update vega12 firmware for 20.45 d683bd5 amdgpu: update vega10 firmware for 20.45 7c81cc2 amdgpu: update renoir firmware for 20.45 3619e57 amdgpu: update navi14 firmware for 20.45 68ce0fb amdgpu: update navi12 firmware for 20.45 e889b80 amdgpu: update navi10 firmware for 20.45 f4edc15 amdgpu: update raven2 firmware for 20.45 e71210f amdgpu: update raven firmware for 20.45 Signed-off-by: Tomas Lara <tl849670@gmail.com> [rebased; removed brcmfmac changes due to removed firmware] Signed-off-by: David Bauer <mail@david-bauer.net>
* linux-firmware: update to version 20210315 and trim down broadcom FWJosef Schlehofer2021-06-062-30/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In there linux-firmware repository located in kernel, there were removed old broadcom firmware [1] as they seem to be likely vulnerable to KrØØk vulnerability (CVE-2019-15126), because Cypress released new versions and superseded by it. In OpenWrt, there is Makefile for cypress-firmware, which already provides the same named packages like it was in linux-firmware. For example, cypress-firmware-43455-sdio provides brcmfmac-firmware-43455-sdio [2]. Changelog between 2020118 and 20210315: 3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210 9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200 c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201 5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6 5a2fd63 iwlwifi: add new FWs from core59-66 release 4f54906 iwlwifi: update 9000-family firmwares 11b7607 iwlwifi: update 7265D firmware e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main 5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406 58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921) e576a1b rtw89: 8852a: add firmware v0.9.12.2 048a7cb WHENCE: add missing symlink for BananaPi M3 aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config 58825f7 brcm: Fix Raspberry Pi 4B NVRAM file 520f71b silabs: add new firmware for WF200 f7915a0 amdgpu: add initial firmware for green sardine 80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5 b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main 66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304 391fd50 linux-firmware: add firmware for MT7921 c5e3240 rtw88: RTL8821C: Update firmware to v24.8 d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210 3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200 13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201 348d8a9 i915: Add DMC v2.01 for ADL-S f33f1f7 i915: Add HuC v7.7.1 for DG1 6a422f5 i915: Add GuC v49.0.1 for DG1 df822a8 qcom: Add venus firmware files for VPU-1.0 11a1db1 qcom: Add SM8250 Compute DSP firmware e55248b qcom: Add SM8250 Audio DSP firmware da74cc6 qcom: add firmware files for Adreno a650 0578970 brcm: Link RPi4's WiFi firmware with DMI machine name. d528862 brcm: Add NVRAM for Vamrs 96boards Rock960 870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes a28a590 cypress: Fix link direction 060ad8b cypress: Link the new cypress firmware to the old brcm files 0f0aefd brcm: remove old brcm firmwares that have newer cypress variants f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB 7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253 e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644 646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work 28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210 23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200 2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201 94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560 27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260 5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main 63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge 0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6 1a08ec9 QCA : Updated firmware files for WCN3991 7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main 7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210 5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210 c487f7d i915: Add GuC firmware v49.0.1 for all platforms d9ffb07 i915: Remove duplicate KBL DMC entry b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018 bc9cd0b linux-firmware: Update AMD SEV firmware 54c797a amdgpu: add sienna cichlid firmware for 20.45 1340e9c amdgpu: update vega20 firmware for 20.45 b260c9c amdgpu: update vega12 firmware for 20.45 d683bd5 amdgpu: update vega10 firmware for 20.45 7c81cc2 amdgpu: update renoir firmware for 20.45 3619e57 amdgpu: update navi14 firmware for 20.45 68ce0fb amdgpu: update navi12 firmware for 20.45 e889b80 amdgpu: update navi10 firmware for 20.45 f4edc15 amdgpu: update raven2 firmware for 20.45 e71210f amdgpu: update raven firmware for 20.45 [1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=0f0aefd733f70beae4c0246edbd2c158d5ce974c [2] https://github.com/openwrt/openwrt/blob/eeda8652f1655d4f9c11e9c9f51ddcd3377d119a/package/firmware/cypress-firmware/Makefile#L124 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* ipq40xx: add netgear wac510 supportRobert Marko2021-06-051-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear WAC510 Insight Managed Smart Cloud Wireless Access Point, an indoor dual-band, dual-radio 802.11ac business-class wireless AP with integrated omnidirectional antennae and two 10/100/1000 Mbps Ethernet ports. For more information see: <https://www.netgear.com/business/wifi/access-points/wac510> Specifications: SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB Flash1: 2 MiB Winbond W25Q16JV SPI-NOR Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port, WAN port active IEEE 802.3af/at PoE in Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1 LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN Serial: Header J2 1 - 3.3 Volt (Do NOT connect!) 2 - TX 3 - RX 4 - Ground WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter! The Serial settings are 115200-8-N-1. Installation via Stock Web Interface: BTW: The default factory console/web interface login user/password are admin/password. In the web interface navigating to Management - Maintenance - Upgrade - 'Firmware Upgrade' will show you what is currently installed e.g.: Manage Firmware Current Firmware Version: V5.0.10.2 Backup Firmware Version: V1.2.5.11 Under 'Upgrade Options' choose Local (alternatively SFTP would be available) then click/select 'Browse File' on the right side, choose openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar and hit the Upgrade button below. After a minute or two your browser should indicate completion printing 'Firmware update complete.' and 'Rebooting AP...'. Note that OpenWrt will use the WAN PoE port as actual WAN port defaulting to DHCP client but NOT allowing LuCI access, use LAN port defaulting to 192.168.1.1/24 to access LuCI. Installation via TFTP Requiring Serial U-Boot Access: Connect to the device's serial port and hit any key to stop autoboot. Upload and boot the initramfs based OpenWrt image as follows: (IPQ40xx) # setenv serverip 192.168.1.1 (IPQ40xx) # setenv ipaddr 192.168.1.2 (IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb (IPQ40xx) # bootm Note: This only runs OpenWrt from RAM and has not installed anything to flash as of yet. One may permanently install OpenWrt as follows: Check the MTD device number of the active partition: root@OpenWrt:/# dmesg | grep 'set to be root filesystem' [ 1.010084] mtd: device 9 (rootfs) set to be root filesystem Upload the factory image ending with .ubi to /tmp (e.g. using scp or tftp). Then flash the image as follows (substituting the 9 in mtd9 below with whatever number reported above): root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi And reboot. Dual Image Configuration: The default U-Boot boot command bootipq uses the U-Boot environment variables primary/secondary to decide which image to boot. E.g. primary=0, secondary=3800000 uses rootfs while primary=3800000, secondary=0 uses rootfs_1. Switching their values changes the active partition. E.g. from within U-Boot: (IPQ40xx) # setenv primary 0 (IPQ40xx) # setenv secondary 3800000 (IPQ40xx) # saveenv Or from a OpenWrt userspace serial/SSH console: fw_setenv primary 0 fw_setenv secondary 3800000 Note that if you install two copies of OpenWrt then each will have its independent configuration not like when switching partitions on the stock firmware. BTW: The kernel log shows which boot partition is active: [ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB) vs. [ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB) Note: After 3 failed boot attempts it automatically switches partition. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [squashed netgear-tar commit into main and rename netgear-tar for now, until it is made generic.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* wireless-regdb: update to version 2021.04.21Felix Fietkau2021-05-261-2/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* treewide: Mark packages nonshared if they depend on @TARGET_Hauke Mehrtens2021-05-249-0/+18
| | | | | | | | | | | | | | This marks all packages which depend on a target with @TARGET nonshared. If they are not marked nonshared they would be build by the SDK build and if this happens with a different SDK, then the SDK from the target the package depends on, the package would not be added to the index. This should fix the image builder for some of these packages. This should fix the image builder at least for bcm27xx/bcm2710 and bcm4908/generic. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: add support for MikroTik SXTsq 5 acRoger Pueyo Centelles2021-04-292-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD), an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet port. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 256 MB - Storage: 16 MB NOR - Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae - Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in - 1x Ethernet LED (green) - 7x user-controllable LEDs · 1x power (blue) · 1x user (green) · 5x rssi (green) Note: Serial UART is probably available on the board, but it has not been tested. Flashing: Boot via TFTP the initramfs image. Then, upload a sysupgrade image via SSH and flash it normally. More info at the "Common procedures for MikroTik products" page https://openwrt.org/toh/mikrotik/common. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* linux-firmware: ath10k: add support for Qualcomm Atheros QCA9377Josef Schlehofer2021-04-171-0/+17
| | | | | | | | | Add firmware and board file for Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter (rev 31) recognized as [168c:0042]. This card supports standard 1x1 802.11ac Wave2, BT5, and MU-MIMO. Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* ipq40xx: add MikroTik hAP ac2 supportRobert Marko2021-04-052-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC (hAP ac²), a indoor dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional antennae, USB port and five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac2 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 128 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in - 1x USB Type A port Installation: Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com>
* treewide: fix spelling 'seperate' -> 'separate'Daniel Golle2021-02-281-1/+1
| | | | | | | This popular spelling mistake was also introduced by myself lately. Fix it everywhere. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* download: add mirror alias for DebianDavid Bauer2021-02-262-2/+2
| | | | | | | Add an alias for Debian packages and download them from the Debian mirror redirector. Signed-off-by: David Bauer <mail@david-bauer.net>
* tfa-layerscape: build fiptool againAdrian Schmutzler2021-02-211-1/+1
| | | | | | | | | | | | | | | | | The ls-ddr-phy package needs fiptool options that are not available via the version from arm-trusted-firmware-tools. This breaks build for layerscape with the recently added LX2160a: create: unrecognized option '--ddr-immem-udimm-1d' Use the tfa-layerscape variant again for now, but rename it to fiptool-layerscape to indicate that it's a specific variant. This reverts 84bc7d31e0a8 ("tfa-layerscape: don't build fiptool"). Fixes: f59d7aab2a37 ("layerscape: add ddr-phy package") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* layerscape: add LX2160ARDB (Rev2.0 silicon) board supportYangbo Lu2021-02-193-2/+12
| | | | | | | | | | | | | | | | | | | | | | The QorIQ LX2160A reference design board provides a comprehensive platform that enables design and evaluation of the LX2160A processor. - Enables network intelligence with the next generation Datapath (DPPA2) which provides differentiated offload and a rich set of IO, including 10GE, 25GE, 40GE, and PCIe Gen4 - Delivers unprecedented efficiency and new virtualized networks - Supports designs in 5G packet processing, network function virtualization, storage controller, white box switching, network interface cards, and mobile edge computing - Supports all three LX2 family members (16-core LX2160A; 12-core LX2120A; and 8-core LX2080A) Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [use AUTORELEASE, add dtb to firmware part] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* layerscape: add ddr-phy packageYangbo Lu2021-02-191-0/+50
| | | | | | | | | Add ddr-phy package for layerscape. Currently only LX2160ARDB requires the package. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [use AUTORELEASE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* layerscape: add FRWY-LS1046A board supportYangbo Lu2021-02-191-1/+5
| | | | | | | | | | | | | | | | | | | The LS1046A Freeway board (FRWY) is a high-performance computing, evaluation, and development platform that supports the QorIQ LS1046A architecture processor capable of support more than 32,000 CoreMark performance. The FRWY-LS1046A board supports the QorIQ LS1046A processor, onboard DDR4 memory, multiple Gigabit Ethernet, USB3.0 and M2_Type_E interfaces for Wi-Fi. The FRWY-LS1046A-TP includes the Coral Tensor Flow Processing Unit that offloads AI/ML inferencing from the CPU to provide significant boost for AI/ML applications. The FRWY-LS1046A-TP includes one M.2 TPU module and more modules can easily be added including USB versions of the module to scale the AI/ML performance. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [rebase, use AUTORELEASE, fix sorting, add dtb to firmware part] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* cypress-firmware: fix PKG_SOURCE_URLÁlvaro Fernández Rojas2021-02-191-1/+1
| | | | | | Download link has been moved. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* treewide: unify OpenWrt hosted source via @OPENWRTPaul Spooren2021-02-052-2/+2
| | | | | | | | | | | Multiple sources are hosted on OpenWrts source server only. The source URLs to point to the server vary based on different epochs in OpenWrts history. Replace all by @OPENWRT which is an "empty" mirror, therefore using the fallback servers sources.cdn.openwrt.org and sources.openwrt.org. Signed-off-by: Paul Spooren <mail@aparcar.org>
* linux-firmware: Add wil6210 firmwareRobert Marko2021-01-051-0/+8
| | | | | | | | This patch adds wil6210 firmware and board files. Firmware version is not up to date but is only freely redistributable one I found. Board file is a generic one so most devices and especially those for long distance PtP links will require so in a ipq-wifi like way. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ath10k-ct-firmware: update to 022 (2020-11-08)Álvaro Fernández Rojas2020-12-281-34/+34
| | | | | | Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ipq40xx: add support for GL.iNet GL-AP1300Dongming Han2020-12-252-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: Reset LED: Power, Internet UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 OTHER: On board with BLE module - by cp210x USB serial chip On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi (IPQ40xx) # run lf By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq806x: add support for NEC Platforms Aterm WG2600HP3Yanase Yuki2020-12-252-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Platforms Aterm WG2600HP3 is a dual-band router based on Qualcomm IPQ8062. Specification ------------- - SoC: Qualcomm IPQ8062 - RAM: 512MiB - Flash memory: SPI-NOR 32MiB (Cypress S25FL256S) - Wi-Fi: Qualcomm QCA9984 (2.4GHz, 1ch - 13ch) - Wi-Fi: Qualcomm QCA9984 (5GHz, 36ch - 64ch, 100ch - 140ch) - Ethernet: 4x 100/1000 Mbps (1x WAN, 4x LAN) - LED: 6x green LED, 6x red LED - Input: 2x tactile switch, 1x SP3T slide switch - Serial console: 115200bps, through-hole J3 - [ ] [GND] [ ] [TX] [RX] ----> DC jack - Power: DC 12V 1.5A This device does not support VHT160 and VHT80+80. Custom BDFs are required to limit VHT capabilities. Flash instructions ------------------ 1. Setup TFTP server (IP address: 192.168.1.2) 2. Put initramfs image into TFTP server directory 3. Connect WG2600HP3 lan port and computer that runs TFTP server 4. Connect to the serial console 5. Interrupt booting by Esc key (password: chiron) 6. Execute the following commands # setenv bootcmd "nboot 0x44000000 1 0x860000" # saveenv # setenv ipaddr 192.168.1.1 # setenv serverip 192.168.1.2 # tftpboot 0x44000000 openwrt-ipq806x-generic-nec_wg2600hp3-initramfs-uImage 7. After booting OpenWrt initramfs image, backup SPI-NOR flash memory 8. Erase firmware partition # mtd erase firmware 9. Run sysupgrade Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* ipq-wifi: Fix suffix for Plasma Cloud PA2200 QCA4019 board-2.binSven Eckelmann2020-12-251-0/+0
| | | | | | | | | | | | | The Makefile is rejecting all files with for a given prefix (here "board-plasmacloud_pa2200") when it didn't match a known suffix. Instead it stops the build with an error like: Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa2200.ipq4019'. Stop. The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019. Fixes: 4871fd2616ac ("ipq40xx: add support for Plasma Cloud PA2200") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq-wifi: Fix suffix for Plasma Cloud PA1200 QCA4019 board-2.binSven Eckelmann2020-12-251-0/+0
| | | | | | | | | | | | | The Makefile is rejecting all files with for a given prefix (here "board-plasmacloud_pa1200") when it didn't match a known suffix. Instead it stops the build with an error like: Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa1200.ipq4019'. Stop. The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019. Fixes: ea5bb6bbfee0 ("ipq40xx: add support for Plasma Cloud PA1200") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: add support for devolo Magic 2 WiFi nextStefan Schake2020-12-222-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8075 (2 ports) PLC: MaxLinear G.hn 88LX5152 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET, WiFi, PLC Button LEDS: red/white home, white WiFi To modify a retail device to run OpenWRT firmware: 1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'. 2) Power on the device while pressing the recessed reset button next to the Ethernet ports. This causes the bootloader to retrieve and start the initramfs. 3) Once the initramfs is booted, the device will come up with IP 192.168.1.1. You can then connect through SSH (allow some time for the first connection). 4) On the device shell, run 'fw_printenv' to show the U-boot environment. Backup this information since it contains device unique factory data. 5) Change the boot command to support booting OpenWRT: # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm' 6) Change directory to /tmp, download the sysupgrade (e.g. through wget) and install it with sysupgrade. The device will reboot into OpenWRT. Notice that there is currently no support for booting the G.hn chip. This requires userland software we lack the rights to share right now. Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
* ipq40xx: add support for Plasma Cloud PA2200Marek Lindner2020-12-223-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200 * GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE * GPIO-LEDs for power (orange) and status (blue) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3at POE+ + used as WAN interface * 12V 2A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: add support for Plasma Cloud PA1200Marek Lindner2020-12-222-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4018 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200 * 3x GPIO-LEDs for status (cyan, purple, yellow) * 1x GPIO-button (reset) * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio4: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio3: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3af/at POE(+) + used as WAN interface * 12V/24V 1A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* wireless-regdb: Update to version 2020.11.20Hauke Mehrtens2020-12-161-2/+2
| | | | | | | | | | | | 9efa1da wireless-regdb: update regulatory rules for Egypt (EG) ede87f5 wireless-regdb: restore channel 12 & 13 limitation in the US 5bcafa3 wireless-regdb: Update regulatory rules for Croatia (HR) 4e052f1 wireless-regdb: Update regulatory rules for Pakistan (PK) on 5GHz f9dfc58 wireless-regdb: update 5.8 GHz regulatory rule for GB c19aad0 wireless-regdb: Update regulatory rules for Kazakhstan (KZ) 07057d3 wireless-regdb: update regulatory database based on preceding changes Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath10k-firmware: remove unused packageÁlvaro Fernández Rojas2020-11-281-182/+0
| | | | | | | All firmwares were added to linux-firmware, so there's no need to keep this package definitions. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath10k-ct-firmware: switch to linux-firmware board binariesÁlvaro Fernández Rojas2020-11-281-135/+37
| | | | | | | | | | Instead of duplicating board firmware binaries, which are exactly the same as the ones from linux-firmware, add dependencies and remove duplicated downloads. Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* linux-firmware: ath10k: add board firmware packagesÁlvaro Fernández Rojas2020-11-282-16/+46
| | | | | | | Split ath10k firmwares into board and firmware packages. This way we can add dependencies to ath10k-ct firmware packages. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* linux-firmware: brcm: use RPI 4B NVRAM fileÁlvaro Fernández Rojas2020-11-252-4/+2
| | | | | | Use the dedicated RPI 4B NVRAM file introduced in 20191215. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* cypress-nvram: add proper package conflictsÁlvaro Fernández Rojas2020-11-251-1/+9
| | | | | | There are linux firmware packages for all RPIs NVRAMs. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* cypress-firmware: add proper package conflictsÁlvaro Fernández Rojas2020-11-251-1/+4
| | | | | | | There are linux firmwares packages for 43362, 43430 and 43455 which shouldn't be installed at the same time as Cypress firmwares. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath10k-ct-firmware: add conflicts and better providesKarel Kočí2020-11-251-11/+71
| | | | | | | | | | | | | This expands packages to define not only provides but also conflicts. These packages provides same files so they should specify conflicts. Second expansion is that *-ct-htt and *-ct-full-htt firmwares can also provide *-ct variant as that allows explicit dependency on CT variant with various firmware modifications. Signed-off-by: Karel Kočí <karel.koci@nic.cz> [Bump PKG_RELEASE and format PROVIDES/CONFLICTS] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* layerscape: enable spi-uart in LS1012A-FRDMPawel Dembicki2020-11-232-1/+14
| | | | | | | | | This patch add missing support of SC16IS740 serial controller, installed on LS1012A-FRDM board. It was required to change RCW bits, because SPI was disabled by default. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* linux-firmware: update to 20201118John Audia2020-11-231-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git log --pretty=oneline --abbrev-commit 20201022..20201118 2ea8667 (tag: 20201118) rtlwifi: v88.2 firmware files for RTL8192CU e850cf3 Merge https://github.com/rjliao-qca/qca-btfw into main 65370db rtw88: RTL8822C: Update firmware to v9.9.4 e371b7c Revert "rtw88: RTL8822C: Update firmware to v9.9.4" 51d2c81 vpdma: Move firmware to ti directory d7a24c9 Merge branch 'master' of https://github.com/shahasit/video-linux-firmware into main 9ee1543 Merge branch 'master' of https://github.com/shahasit/bt-linux-firmware into main 3bcc4c1 amdgpu: update picasso VCN firmware b6b4542 amdgpu: update raven2 VCN firmware 79aa335 amdgpu: update raven VCN firmware c93834e rtw88: RTL8822C: Update firmware to v9.9.4 3ef6c93 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099A_281A b503c96 Merge branch 'ath10k-20201023' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware into main 463fdea QCA: Update Bluetooth firmware for QCA6390 8a46c32 qcom : updated venus firmware files for v5.4 d7793e5 QCA : Fixed BT SSR due to command timeout / IO fatal error d842d8c ath11k: QCA6390 hw2.0: add to WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 8fb1a6e ath11k: QCA6390 hw2.0: add board-2.bin 34cb5fc ath11k: IPQ8074 hw2.0: add to WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 c0a8efd ath11k: IPQ8074 hw2.0: add board-2.bin ac7f5e9 ath11k: IPQ6018 hw1.0: add to WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 2594e51 ath11k: IPQ6018 hw1.0: add board-2.bin d8f10d4 ath10k: QCA6174 hw3.0: add firmware-sdio-6.bin version WLAN.RMH.4.4.1-00077 6652297 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00131 36059aa ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00131 1e5629d ath10k: QCA6174 hw3.0: update board-2.bin e315d1a ath10k: QCA6174 hw3.0: update firmware-6.bin to WLAN.RM.4.4.1-00157-QCARMSWPZ-1 Signed-off-by: John Audia <graysky@archlinux.us>
* linux-firmware: update to 20201022John Audia2020-11-011-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git log --pretty=oneline --abbrev-commit 20200918..20201022 dae4b4c (HEAD -> main, tag: 20201022, origin/master, origin/main, origin/HEAD) Merge branch 'v1.1.5' of https://github.com/irui-wang/linux_fw_vpu_v1.1.5 into main 04f71fe cypress: add Cypress firmware and clm_blob files 4d0755b Merge https://github.com/shahasit/bt-linux-firmware into main 2a262bb Merge https://github.com/shahasit/video-linux-firmware into main c024640 Merge tag 'iwlwifi-fw-2020-10-14' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main 09e8cff rtl_bt: Update RTL8821C BT FW to 0xAA6C_A99E d7904d5 ath10k: add SDIO firmware for QCA9377 WiFi ecdc272 Merge branch 'dg1_dmc_v2_02' of git://anongit.freedesktop.org/drm/drm-firmware into main c86361d ice: update package file to 1.3.16.0 76ceac8 mediatek: separate venc service thread 8877322 QCA : Updated firmware file for WCN3991 4f41e9d iwlwifi: update and add new FWs from core56-54 release 346057d iwlwifi: update 3168, 7265D, 8000C and 8265 firmwares a140ef3 i915: Add DG1 DMC v2.02 a09b728 qcom : updated venus firmware files for v5.4 58d41d0 ice: Add comms package file for Intel E800 series driver c1bef9e copy-firmware: Always write Link: entries b95e230 Merge commit 'ad1da95d52f1a9206da3ef52f3484f3b89ec6615' of https://github.com/shahasit/linux-firmware-bt into main 0b884ec amdgpu: update vega20 firmware for 20.40 bca0233 amdgpu: update vega12 firmware for 20.40 8652e02 amdgpu: update vega10 firmware for 20.40 9f46d48 amdgpu: update renoir firmware for 20.40 e667605 amdgpu: update raven2 firmware for 20.40 a487f2f amdgpu: update raven firmware for 20.40 aa7b732 amdgpu: update picasso firmware for 20.40 a18981e amdgpu: update navi14 firmware for 20.40 1696e2e amdgpu: update navi12 firmware for 20.40 6b8a6ea amdgpu: update navi10 firmware for 20.40 5b30b38 linux-firmware: Add new VPDMA firmware 1b8.bin ad1da95 QCA : Updated firmware files for WCN3991 b78a66c linux-firmware: Update firmware for Cadence MHDP8546 DP bridge afbfb5f linux-firmware: Update firmware patch for Intel Bluetooth 7265 (D1) a38b8ed Mellanox: Add new mlxsw_spectrum firmware xx.2008.1312 1487a8a linux-firmware: nvidia: move firmware symlinks to WHENCE bdd5617 linux-firmware: move i915 firmware symlinks to WHENCE ab69b57 linux-firmware: move iwlwifi-7265D-10.ucode symlink to WHENCE 49c4ff5 Merge branch 'mrvl-prestera' of https://github.com/PLVision/linux-firmware into main 7a02212 linux-firmware: Update Marvell Switchdev firmware with ABI changes Signed-off-by: John Audia <graysky@archlinux.us>
* layerscape: update ls-rcw to LSDK-20.04-update-290520Biwen Li2020-10-261-4/+4
| | | | | | | | | Update ls-rcw to LSDK-20.04-update-290520. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [rebase, fix PKG_RELEASE change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: improve support for Edgecore ECW5211Sungbo Eo2020-10-072-2/+0
| | | | | | | | | | | | | | | | | | | This adds several stylistic and functional improvements of the recently added Edgecore ECW5211, especially: * Drop the local BDFs as those are already in the upstream under different names * Add SPDX tag to DTS * Add label MAC address * Move LED trigger to DTS * Remove unnecessary status="okay" * Disable unused SS USB phy as the USB port only supports USB 2.0 * Make uboot-env partition writable * Remove qcom,poll_required_dynamic property as the driver does not use it * Tidy up the device recipe Fixes: 4488b260a02e ("ipq40xx: add Edgecore ECW5211 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> Acked-by: Robert Marko <robert.marko@sartura.hr>
* linux-firmware: update to 20200918David Bauer2020-10-031-3/+3
| | | | | | | | | | | | | | | | | | | 00a84c5 linux-firmware: Update AMD SEV firmware 71338c2 Merge branch 'for-master' of https://github.com/CosmicPenguin/linux-firmware into main 07367b9 linux-firmware: Update firmware file for Intel Bluetooth AX200 1d1586a linux-firmware: Update firmware file for Intel Bluetooth AX201 28b333d linux-firmware: Update firmware file for Intel Bluetooth 9560 db30380 linux-firmware: Update firmware file for Intel Bluetooth 9260 eb3aa1f Mellanox: Add new mlxsw_spectrum firmware xx.2008.1310 ec88f05 mediatek: update MT7915 firmware to 20200819 a9993f8 brcm: Fix a stale symlink for RPi3 model b+ f48fec4 qcom: Add updated a5xx and a6xx microcode d5f9eea wl18xx: update firmware file 8.9.0.0.83 7a237c6 linux-firmware: mt7615: update firmware to 20200814 version 74bd44f amdgpu: add navi12 firmware from 20.30 b9f69cd amdgpu: update navi10 firmware for 20.30 Signed-off-by: David Bauer <mail@david-bauer.net>
* ath10k-firmware: package Wave1 from linux-firmwareDavid Bauer2020-09-282-4/+4
| | | | | | | | | | The firmware for Wave1 chips was updated to the latest release 10.2.4-1.0-00047 at the end of 2019 (commit 513d70cc50b). Package firmware for these chips from linux-firmware. This avoids downloading the ath10k-firmware repository. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: Add support for Linksys MR8300 (Dallas)Hans Geiblinger2020-09-253-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys MR8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Hardware Highlights: SoC: IPQ4019 at 717 MHz (4 CPUs) RAM: 512MB RAM SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs) RAM: 512M DDR3 FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel) ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks) BTN: Reset and WPS USB: USB3.0, single port on rear with LED SERIAL: Serial pads internal (unpopulated) LED: Four status lights on top + USB LED WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14 WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64 WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165 Support is based on the already supported EA8300. Key differences: EA8300 has 256MB RAM where MR8300 has 512MB RAM. MR8300 has a revised top panel LED setup. Installation: "Factory" images may be installed directly through the OEM GUI using URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1) Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com> [copied Hardware-highlights from EA8300. Fixed alphabetical order. fixed commit subject, removed bogus unit-address of keys, fixed author (used Signed-off-By to From:) ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Luma Home WRTQ-329ACNTomasz Maciej Nowak2020-09-252-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band wireless access point. Specification SoC: Qualcomm Atheros IPQ4018 RAM: 256 MB DDR3 Flash: 2 MB SPI NOR 128 MB SPI NAND WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R integrated Ethernet: 2x 10/100/1000 Mbps QCA8075 USB: 1x 2.0 Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU Buttons: 1x GPIO controlled EEPROM: 16 Kbit, compatible with AT24C16 UART: row of 4 holes marked on PCB as J19, starting count from the side of J19 marking on PCB 1. GND, 2. RX, 3. TX, 4. 3.3V baud: 115200, parity: none, flow control: none The device supports OTA or USB flash drive updates, unfotunately they are signed. Until the signing key is known, the UART access is mandatory for installation. The difficult part is disassembling the casing, there are a lot of latches holding it together. Teardown Prepare three thin, but sturdy, prying tools. Place the device with back of it facing upwards. Start with the wall having a small notch. Insert first tool, until You'll feel resistance and keep it there. Repeat the procedure for neighbouring walls. With applying a pressure, one edge of the back cover should pop up. Now carefully slide one of the tools to free the rest of the latches. There's no need to solder pins to the UART holes, You can use hook clips, but wiring them outside the casing, will ease debuging and recovery if problems occur. Installation 1. Prepare TFTP server with OpenWrt initramfs image. 2. Connect to UART port (don't connect the voltage pin). 3. Connect to LAN port. 4. Power on the device, carefully observe the console output and when asked quickly enter the failsafe mode. 5. Invoke 'mount_root'. 6. After the overlayfs is mounted run: fw_setenv bootdelay 3 This will allow to access U-Boot shell. 7. Reboot the device and when prompted to stop autoboot, hit any key. 8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use 'setenv' to do that, then run following commands: tftpboot 0x84000000 <openwrt_initramfs_image_name> bootm 0x84000000 and wait till OpenWrt boots. 9. In OpenWrt command line run following commands: fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000" fw_setenv bootcmd "run openwrt" 10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it with: ubirmvol /dev/ubi0 -N ubi_rootfs sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name> 11. After flashing, the access point will reboot to OpenWrt, then it's ready for configuration. Reverting to OEM firmware 1. Execute installation guide steps: 1, 2, 3, 7, 8. 2. In OpenWrt command line run following commands: ubirmvol /dev/ubi0 -N rootfs_data ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N kernel ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs ubimkvol /dev/ubi0 -S 34 -N kernel1 ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1 ubimkvol /dev/ubi0 -S 264 -N rootfs_data fw_setenv bootcmd bootipq 3. Reboot. Known issues The LEDs ring doesn't have any dedicated driver or application to control it, the only available option atm is to manipulate it with 'i2cset' command. The default action after applying power to device is spinning blue light. This light will stay active at all time. To disable it install 'i2c-tools' with opkg and run: i2cset -y 2 0x48 3 1 0 0 i The light will stay off until next cold boot. Additional information After completing 5. step from installation guide, one can disable asking for root password on OEM firmware by running: sed -e 's/root:x:/root::/' -i /etc/passwd This is useful for investigating the OEM firmware. One can look at the communication between the stock firmware and the vendor's cloud servers or as a way of making a backup of both flash chips. The root password seems to be constant across all sold devices. This is output of 'led_ctl' from OEM firmware to illustrate possibilities of LEDs ring: Usage: led_ctl [status | upgrade | force_upgrade | version] led_ctl solid COLOR <brightness> led_ctl single COLOR INDEX <brightness 0 - 15> led_ctl spinning COLOR <period 1 - 16 (lower = faster)> led_ctl fill COLOR <period 1 - 16 (lower = faster)> ( default is 5 ) led_ctl flashing COLOR <on dur 1 - 128> <off dur 1 - 128> (default is 34) ( default is 34 ) led_ctl pulsing COLOR COLOR: red, green, blue, yellow, purple, cyan, white Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit, changed ubi volumes for easier integration, slightly reworded commit message, changed ubi volume layout to use standard names all around] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* firmware: intel-microcode: update to 20200616Tan Zien2020-09-181-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | intel-microcode (3.20200616.1) * New upstream microcode datafile 20200616 + Downgraded microcodes (to a previously shipped revision): sig 0x000406e3, pf_mask 0xc0, 2019-10-03, rev 0x00d6, size 101376 sig 0x000506e3, pf_mask 0x36, 2019-10-03, rev 0x00d6, size 101376 * Works around hangs on boot on Skylake-U/Y and Skylake Xeon E3, * This update *removes* the SRBDS mitigations from the above processors * Note that Debian had already downgraded 0x406e3 in release 3.20200609.2 intel-microcode (3.20200609.2) * REGRESSION FIX: 0x406e3: rollback to rev 0xd6 and document regression * Microcode rollbacks (closes: LP#1883002) sig 0x000406e3, pf_mask 0xc0, 2019-10-03, rev 0x00d6, size 101376 * THIS REMOVES THE SECURITY FIXES FOR SKYLAKE-U/Y PROCESSORS * Avoid hangs on boot on (some?) Skylake-U/Y processors, * ucode-blacklist: blacklist models 0x8e and 0x9e from late-loading, just in case. Note that Debian does not do late loading by itself. Refer to LP#1883002 for the report, 0x806ec hangs upon late load. intel-microcode (3.20200609.1) * SECURITY UPDATE * For most processors: SRBDS and/or VRDS, L1DCES mitigations depending on the processor model * For Skylake HEDT and Skylake Xeons with signature 0x50654: VRDS and L1DCES mitigations, plus mitigations described in the changelog entry for package release 3.20191112.1. * Expect some performance impact, the mitigations are enabled by default. A Linux kernel update will be issued that allows one to selectively disable the mitigations. * New upstream microcode datafile 20200609 * Implements mitigation for CVE-2020-0543 Special Register Buffer Data Sampling (SRBDS), INTEL-SA-00320, CROSSTalk * Implements mitigation for CVE-2020-0548 Vector Register Data Sampling (VRDS), INTEL-SA-00329 * Implements mitigation for CVE-2020-0549 L1D Cache Eviction Sampling (L1DCES), INTEL-SA-00329 * Known to fix the regression introduced in release 2019-11-12 (sig 0x50564, rev. 0x2000065), which would cause several systems with Skylake Xeon, Skylake HEDT processors to hang while rebooting * Updated Microcodes: sig 0x000306c3, pf_mask 0x32, 2019-11-12, rev 0x0028, size 23552 sig 0x000306d4, pf_mask 0xc0, 2019-11-12, rev 0x002f, size 19456 sig 0x00040651, pf_mask 0x72, 2019-11-12, rev 0x0026, size 22528 sig 0x00040661, pf_mask 0x32, 2019-11-12, rev 0x001c, size 25600 sig 0x00040671, pf_mask 0x22, 2019-11-12, rev 0x0022, size 14336 sig 0x000406e3, pf_mask 0xc0, 2020-04-27, rev 0x00dc, size 104448 sig 0x00050653, pf_mask 0x97, 2020-04-24, rev 0x1000157, size 32768 sig 0x00050654, pf_mask 0xb7, 2020-04-24, rev 0x2006906, size 34816 sig 0x00050656, pf_mask 0xbf, 2020-04-23, rev 0x4002f01, size 52224 sig 0x00050657, pf_mask 0xbf, 2020-04-23, rev 0x5002f01, size 52224 sig 0x000506e3, pf_mask 0x36, 2020-04-27, rev 0x00dc, size 104448 sig 0x000806e9, pf_mask 0x10, 2020-04-27, rev 0x00d6, size 103424 sig 0x000806e9, pf_mask 0xc0, 2020-04-27, rev 0x00d6, size 103424 sig 0x000806ea, pf_mask 0xc0, 2020-04-27, rev 0x00d6, size 103424 sig 0x000806eb, pf_mask 0xd0, 2020-04-27, rev 0x00d6, size 103424 sig 0x000806ec, pf_mask 0x94, 2020-04-23, rev 0x00d6, size 103424 sig 0x000906e9, pf_mask 0x2a, 2020-04-23, rev 0x00d6, size 103424 sig 0x000906ea, pf_mask 0x22, 2020-04-27, rev 0x00d6, size 102400 sig 0x000906eb, pf_mask 0x02, 2020-04-23, rev 0x00d6, size 103424 sig 0x000906ec, pf_mask 0x22, 2020-04-27, rev 0x00d6, size 102400 sig 0x000906ed, pf_mask 0x22, 2020-04-23, rev 0x00d6, size 103424 * Restores the microcode-level fixes that were reverted by release 3.20191115.2 for sig 0x50654 (Skylake Xeon, Skylake HEDT) intel-microcode (3.20200520.1) * New upstream microcode datafile 20200520 + Updated Microcodes: sig 0x000206d6, pf_mask 0x6d, 2020-03-04, rev 0x0621, size 18432 sig 0x000206d7, pf_mask 0x6d, 2020-03-24, rev 0x071a, size 19456 intel-microcode (3.20200508.1) * New upstream microcode datafile 20200508 + Updated Microcodes: sig 0x000706e5, pf_mask 0x80, 2020-03-12, rev 0x0078, size 107520 * Likely fixes several critical errata on IceLake-U/Y causing system hangs intel-microcode (3.20191115.2) * Microcode rollbacks (closes: #946515, LP#1854764): sig 0x00050654, pf_mask 0xb7, 2019-07-31, rev 0x2000064, size 33792 * Avoids hangs on warm reboots (cold boots work fine) on HEDT and Xeon processors with signature 0x50654. intel-microcode (3.20191115.1) * New upstream microcode datafile 20191115 + Updated Microcodes: sig 0x000406e3, pf_mask 0xc0, 2019-10-03, rev 0x00d6, size 101376 sig 0x000506e3, pf_mask 0x36, 2019-10-03, rev 0x00d6, size 101376 sig 0x000806e9, pf_mask 0x10, 2019-10-15, rev 0x00ca, size 100352 sig 0x000806e9, pf_mask 0xc0, 2019-09-26, rev 0x00ca, size 100352 sig 0x000806ea, pf_mask 0xc0, 2019-10-03, rev 0x00ca, size 100352 sig 0x000806eb, pf_mask 0xd0, 2019-10-03, rev 0x00ca, size 100352 sig 0x000806ec, pf_mask 0x94, 2019-10-03, rev 0x00ca, size 100352 sig 0x000906e9, pf_mask 0x2a, 2019-10-03, rev 0x00ca, size 100352 sig 0x000906ea, pf_mask 0x22, 2019-10-03, rev 0x00ca, size 99328 sig 0x000906eb, pf_mask 0x02, 2019-10-03, rev 0x00ca, size 100352 sig 0x000906ec, pf_mask 0x22, 2019-10-03, rev 0x00ca, size 99328 sig 0x000906ed, pf_mask 0x22, 2019-10-03, rev 0x00ca, size 100352 sig 0x000a0660, pf_mask 0x80, 2019-10-03, rev 0x00ca, size 91136 intel-microcode (3.20191113.1) * New upstream microcode datafile 20191113 + SECURITY UPDATE, refer to the 3.20191112.1 changelog entry for details Adds microcode update for CFL-S (Coffe Lake Desktop) INTEL-SA-00270, CVE-2019-11135, CVE-2019-0117 + Updated Microcodes (previously removed): sig 0x000906ec, pf_mask 0x22, 2019-08-14, rev 0x00c6, size 99328 intel-microcode (3.20191112.1) * New upstream microcode datafile 20191112 + SECURITY UPDATE - Implements MDS mitigation (TSX TAA), INTEL-SA-00270, CVE-2019-11135 - Implements TA Indirect Sharing mitigation, and improves the MDS mitigation (VERW) - Fixes FIVR (Xeon Voltage Modulation) vulnerability, INTEL-SA-00271, CVE-2019-11139 - Fixes SGX vulnerabilities and errata (including CVE-2019-0117) + CRITICAL ERRATA FIXES - Fixes Jcc conditional jump macro-fusion erratum (Skylake+, except Ice Lake), causes a 0-3% typical perforance hit (can be as bad as 10%). But ensures the processor will actually jump where it should, so don't even *dream* of not applying this fix. - Fixes AVX SHUF* instruction implementation flaw erratum + Removed Microcodes: sig 0x000906ec, pf_mask 0x22, 2019-02-14, rev 0x00ae, size 98304 + New Microcodes: sig 0x000406d8, pf_mask 0x01, 2019-09-16, rev 0x012d, size 84992 sig 0x00050656, pf_mask 0xbf, 2019-09-05, rev 0x400002c, size 51200 sig 0x00060663, pf_mask 0x80, 2018-04-17, rev 0x002a, size 87040 sig 0x000706a8, pf_mask 0x01, 2019-08-29, rev 0x0016, size 74752 sig 0x000706e5, pf_mask 0x80, 2019-09-05, rev 0x0046, size 102400 sig 0x000a0660, pf_mask 0x80, 2019-08-27, rev 0x00c6, size 91136 + Updated Microcodes: sig 0x000406e3, pf_mask 0xc0, 2019-08-14, rev 0x00d4, size 101376 sig 0x00050654, pf_mask 0xb7, 2019-09-05, rev 0x2000065, size 34816 sig 0x00050657, pf_mask 0xbf, 2019-09-05, rev 0x500002c, size 51200 sig 0x000506e3, pf_mask 0x36, 2019-08-14, rev 0x00d4, size 101376 sig 0x000706a1, pf_mask 0x01, 2019-08-28, rev 0x0032, size 73728 sig 0x000806e9, pf_mask 0x10, 2019-08-14, rev 0x00c6, size 99328 sig 0x000806e9, pf_mask 0xc0, 2019-08-14, rev 0x00c6, size 100352 sig 0x000806ea, pf_mask 0xc0, 2019-08-14, rev 0x00c6, size 99328 sig 0x000806eb, pf_mask 0xd0, 2019-08-14, rev 0x00c6, size 100352 sig 0x000806ec, pf_mask 0x94, 2019-08-14, rev 0x00c6, size 100352 sig 0x000906e9, pf_mask 0x2a, 2019-08-14, rev 0x00c6, size 100352 sig 0x000906ea, pf_mask 0x22, 2019-08-14, rev 0x00c6, size 99328 sig 0x000906eb, pf_mask 0x02, 2019-08-14, rev 0x00c6, size 100352 sig 0x000906ed, pf_mask 0x22, 2019-08-14, rev 0x00c6, size 99328 + Updated Microcodes (previously removed): sig 0x00050653, pf_mask 0x97, 2019-09-09, rev 0x1000151, size 32768 Signed-off-by: Tan Zien <nabsdh9@gmail.com>
* firmware: amd64-microcode: update to 20191218Tan Zien2020-09-181-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | amd64-microcode (3.20191218.1) * New microcode update packages from AMD upstream: + Removed Microcode updates (known to cause issues): sig 0x00830f10, patch id 0x08301025, 2019-07-11 * README: update for new release amd64-microcode (3.20191021.1) * New microcode update packages from AMD upstream: + New Microcodes: sig 0x00830f10, patch id 0x08301025, 2019-07-11 + Updated Microcodes: sig 0x00800f12, patch id 0x08001250, 2019-04-16 sig 0x00800f82, patch id 0x0800820d, 2019-04-16 amd64-microcode (3.20181128.1) * New microcode update packages from AMD upstream: + New Microcodes: sig 0x00800f82, patch id 0x0800820b, 2018-06-20 Signed-off-by: Tan Zien <nabsdh9@gmail.com>
* ipq40xx: add Edgecore OAP-100 supportJohn Crispin2020-09-172-0/+2
| | | | | | | | | | | | | | | | flashing the unit * first update to latest edcore FW as per the PDF instructions * boot the initramfs - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm * inside the initramfs call the following commiands - ubiattach -p /dev/mtd0 - ubirmvol /dev/ubi0 -n0 - ubirmvol /dev/ubi0 -n1 - ubirmvol /dev/ubi0 -n2 * scp the sysupgrade image to the board and call - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: add Edgecore ECW5211 supportRobert Marko2020-09-172-0/+2
| | | | | | | | | | | | | | | | | This patch adds support for the Edgecore ECW5211 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7 - RAM: 256MB DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB MX35LFxGE4AB SPI-NAND - Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn) - CC2540 BLE connected to USB 2.0 port - Atmel AT97SC3205T I2C TPM Signed-off-by: Robert Marko <robert.marko@sartura.hr>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-01 17:00:21 +0000