aboutsummaryrefslogtreecommitdiffstats
path: root/package/boot
Commit message (Collapse)AuthorAgeFilesLines
* uboot-mediatek: mt7622: suppress unwanted pinctrl warningDaniel Golle2022-09-033-6/+47
| | | | | | | Import patch which removes the default pinctrl of uart0 to suppress the unwanted warning. Apply also to downstream boards. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: backport fix for unstable UART on MT7622Daniel Golle2022-09-031-0/+26
| | | | | | | | | | | | | Import pending patch "arm: dts: mt7622: force high-speed mode for uart" from Weijie Gao <weijie.gao@mediatek.com> fixing the UART problems on MT7622 which made it hard to use the U-Boot menu on devices with this SoC. This patch is also contained in commit c09eb08dad ("uboot-mediatek: add support for MT798x platforms") in the development branch. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: no compression means IH_COMP_NONEDaniel Golle2022-09-034-4/+121
| | | | | | | | | | | Treat missing compression node in FIT image as IH_COMP_NONE. This is implicentely already happening in most places, but for now was still triggering an annoying warning about initramfs compression being obsolete despite compression note being absent. Fix this. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 0a18456ffc25d6a26911fca6f9079090243c2284)
* uboot-mediatek: fix factory reset on UBIDaniel Golle2022-09-032-2/+2
| | | | | | | | Truncating a UBI volume using `ubi write 0x0 volname 0x0` results in segfault on newer U-Boot. Write 1MB of 0s instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit d118cbdfece181994a96d1bcb1868bd807d481bf)
* uboot-envtools: mt7622: use 4k sectors for UniFi 6 LR (ubootmod)Daniel Golle2022-09-031-1/+1
| | | | | | | | | Use 4k sectors when accessing the U-Boot environment on the 64MiB SPI-NOR flash chip found in the UniFi 6 LR. The speeds up environment write access as only 4kB instead of 64kB have to be written. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit f0adf253fdcf78ce005dad9652b405a4ad2726e6)
* uboot-mediatek: fix Ubiquiti UniFi 6 LR U-Boot modDaniel Golle2022-09-031-20/+8
| | | | | | | | Image names as well as the calculation of the padded image size did not work as intended. Fix that. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 0bc8889e7b4f19d7e33a9be6c3db918fed051501)
* at91bootstrap: use sdmmc0 as booting media for sama5d27_som1_ekClaudiu Beznea2022-09-021-7/+1
| | | | | | | | | | | Commit 0b7c66c ("at91bootstrap: add sama5d27_som1_eksd1_uboot as default defconfig") changed default booting media for sama5d27_som1_ek board w/o any reason. Changed it back to sdmmc0 as it is for all the other Microchip supported distributions for this board (Buildroot, Yocto Project). The initial commit cannot be cleanly reverted. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> (cherry picked from commit e9f12931e60ee291cd7d2c8fd19a14682dae0197)
* uboot-at91: use sdmmc0 as booting media for sama5d27_som1_ekClaudiu Beznea2022-09-021-3/+3
| | | | | | | | | | | | Commit adc69fe (""uboot-at91: changed som1 ek default defconfigs") changed the booting media to sdmmc1 as default booting w/o any reason. The Microchip releases for the rest of supported distributions (Buildroot, Yocto Project) uses sdmmc0 as default booting media for this board. Thus change it back to sdmmc0. With this remove references to sdmmc1 config. The initial commit cannot be cleanly reverted. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> (cherry picked from commit 9a49788008c18fd4fe6fefe9697962c102fb14c6)
* ramips: add support for MTS WG430223Mikhail Zhilkin2022-08-161-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan WG443223). Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 128 MiB Flash: 128 MiB (Winbond W29N01HV) Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: No Button: 1 (Reset/WPS) LEDs: 2 (Red, Green) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WG430223 Installation ------------ 1. Login to the router web interface (superadmin:serial number) 2. Navigate to Administration -> Miscellaneous -> Access control lists & enable telnet & enable "Remote control from any IP address" 3. Connect to the router using telnet (default admin:admin) 4. Place *factory.trx on any web server (192.168.1.2 in this example) 5. Connect to the router using telnet shell (no password required) 6. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 7. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 8. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 9. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | A4:xx:xx:51:xx:F4 | No MACs was | | LAN | A4:xx:xx:51:xx:F6 | found on Flash | | WAN | A4:xx:xx:51:xx:F4 | [1] | | WLAN_2g | A4:xx:xx:51:xx:F5 | | | WLAN_5g | A6:xx:xx:21:xx:F5 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several MTS WG430223 devices even within the same broadcast domain. Stock firmware image format --------------------------- The same as Beeline Smartbox Flash but with another trx magic +--------------+---------------+----------------------------------------+ | Offset | | Description | +==============+===============+========================================+ | 0x0 | 31 52 48 53 | TRX magic "1RHS" | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit 498c15376bae109bfe130cc5581f83e4cc52c0f9)
* arm-trusted-firmware-mediatek: skip bad blocks on SPI-NAND (SNFI)Daniel Golle2022-08-121-0/+40
| | | | | | | | | | Add patch to skip bad blocks when reading from SPI-NAND. This is needed in case erase block(s) early in the flash inside the FIP area are bad and hence need to be skipped in order to be able to boot on such damaged chips. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit c0109537d13650e3cfd4d4840c571a0d557b303a)
* uboot-mvebu: update to v2022.07Andre Heider2022-08-063-33/+22
| | | | | | | | | | | | | | | | | - Release announcement: https://lore.kernel.org/u-boot/20220711134339.GV1146598@bill-the-cat/ - Changes between 2022.04 and 2022.07: https://source.denx.de/u-boot/u-boot/-/compare/v2022.04...v2022.07?from_project_id=531 Remove one upstreamed patch and add patch to fix issue with sunxi tool as it uses function from newer version libressl (3.5.0). Signed-off-by: Andre Heider <a.heider@gmail.com> Tested-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [Turris Omnia] (cherry picked from commit 24bf6813bad98a8eba5430ed5e4da89d54797274) Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [Improve commit message]
* ramips: support fw_printenv for Netgear WAX202Wenli Looi2022-08-061-1/+2
| | | | | | | | | Config partition contains uboot env for the first 0x20000 bytes. The rest of the partition contains other data including the device MAC address and the password printed on the label. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> (cherry picked from commit 0bfe1cfbb13c58d909951cab9fac8910ccbe74f3)
* ramips: Add support command fw_setsys for Xiaomi routersOleg S2022-08-061-4/+10
| | | | | | | | | | | | | The system parameters are contained in the Bdata partition. To use the fw_setsys command, you need to create a file fw_sys.config. This file is created after calling the functions ubootenv_add_uci_sys_config and ubootenv_add_app_config. Signed-off-by: Oleg S <remittor@gmail.com> [ wrapped commit description to 72 char ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> (cherry picked from commit 6c7e337c80f92693c2ca628a4a56aeaec4cc3ca8)
* uboot-at91: fix build on buildbotsClaudiu Beznea2022-07-311-1/+2
| | | | | | | | | | | | | | | | Buidbots are throwing the following compile error: In file included from tools/aisimage.c:9: include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory ^~~~~~~~~~~~~~~ compilation terminated. Fix it by passing `UBOOT_MAKE_FLAGS` variable to make. Suggested-by: Petr Štetiar <ynezz@true.cz> Fixes: 6d5611af2813 ("uboot-at91: update to linux4sam-2022.04") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> (cherry picked from commit 95a24b54792ccf072c029edad495deb529383478)
* uboot-at91: update to linux4sam-2022.04Claudiu Beznea2022-07-312-16/+6
| | | | | | | | | | Update uboot-at91 to linux4sam-2022.04. As linux4sam-2022.04 is based on U-Boot v2022.01 which contains commit 93b196532254 ("Makefile: Only build dtc if needed") removed also the DTC variable passed to MAKE to force the compilation of DTC. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> (cherry picked from commit 6d5611af2813e5f06fbf9b400ef0fe642f16c566)
* at91bootstrap: update at91bootstrap v4 targets to v4.0.3Claudiu Beznea2022-07-311-3/+3
| | | | | | | Update AT91Bootstrap v4 capable targets to v4.0.3. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> (cherry picked from commit 859f5f9aec23c96ec3151175c349ffdbe6b108ef)
* uboot-bcm4908: include SoC in output filesRafał Miłecki2022-07-281-2/+4
| | | | | | | | | This fixes problem of overwriting BCM4908 U-Boot and DTB files by BCM4912 ones. That bug didn't allow booting BCM4908 devices. Fixes: f4c2dab544ec2 ("uboot-bcm4908: add BCM4912 build") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit a8e1e30543239e85ff5dc220368164b66cf73fba)
* layerscape: update PKG_HASH / PKG_MIRROR_HASHChristian Lamparter2022-07-232-2/+2
| | | | | | | | | | | The change of the PKG_VERSION caused the hash of the package to change. This is because the PKG_VERSION is present in the internal directory structure of the archive. Fixes: 038d5bdab117 ("layerscape: use semantic versions for LSDK") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit e879cccaa21563a7cdf47797b18fb86723720158) (cherry picked from commit d4391ef073825f5817cdbcc3fc215311f1bbb461)
* uboot-mediatek: update UniFi 6 LR board nameDaniel Golle2022-07-041-1/+1
| | | | | | | | Select matching U-Boot for both v1 and v2 variants. Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1") Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 2caa03ec8607fb38e11ac1ce3c7b698f80191b49)
* uboot-mvebu: update to version v2022.04Josef Schlehofer2022-06-148-524/+2
| | | | | | | | | | | | | | | Release announcement: https://lore.kernel.org/u-boot/20220404143253.GQ14476@bill-the-cat/ Release notes between tags: https://source.denx.de/u-boot/u-boot/-/compare/v2022.01...v2022.04?from_project_id=531 All patches were removed, since they are included in this release. Run tested: Turris Omnia, mvebu/cortex-a9, OpenWrt daily snapshots Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (cherry picked from commit 4f51f1fc9b3597d24de442cfff253fddce478d17)
* uboot-mvebu: remove enabled CONFIG_CMD_SETEXPRJosef Schlehofer2022-06-141-7/+0
| | | | | | | | | | | | | | | | | | | | | | | We don't need to make sure that we want to have enabled CONFIG_CMD_SETEXPR by default, since this is already done in U-boot [1]. This was actually needed only for clearfog board [2], which was added in commit: da0005a6d08ae33d958a6d8a6c0c12dc07b5b2b8 ("uboot-mvebu: add patch to enable setexpr for clearfog boards) and send to U-boot to fix it properly. After a while, there was added support for Turris Omnia, which uses setexpr as well [3], but for this board, there are no fixes needed in U-boot and that's why we can remove this option here. It is helpful with shell scripting. If some downstream distributions are using it, they should correct it in defconfig for related boards. [1] https://source.denx.de/u-boot/u-boot/-/blob/e95afa56753cebcd20a5114b6d121f281b789006/cmd/Kconfig#L1504 [2] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/clearfog.bootscript#L7 [3] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/turris-omnia.bootscript#L2 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (cherry picked from commit 69cef74c671cb7fa738a5a4c9a283c29f45326c7)
* uboot-mvebu: add patch to enable setexpr for clearfog boardsJosef Schlehofer2022-06-141-0/+31
| | | | | | | | | | | | | | | Option CMD_SETEXPR is already default in U-boot [1], since this was disabled since initial version for this board, there is send this patch to U-boot mailing list to enable it. It is required to use in OpenWrt bootscript for these boards [2]. [1] https://source.denx.de/u-boot/u-boot/-/blob/e95afa56753cebcd20a5114b6d121f281b789006/cmd/Kconfig#L1504 [2] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/clearfog.bootscript#L7 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (cherry picked from commit b3c2072504867b8ca00dde37f531edf0cfbe3359)
* uboot-imx: fix wrong make flags overridingPetr Štetiar2022-06-071-2/+2
| | | | | | | | | | | | | | | | | | | | Buidbots are currently choking on the following compile error: In file included from tools/aisimage.c:9: include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory # include <openssl/evp.h> ^~~~~~~~~~~~~~~ compilation terminated. This is caused by a complete overriding of make flags which are provided correctly in `UBOOT_MAKE_FLAGS` variable, but currently overriden instead of extended. This then leads to the usage of build host include dirs, which are not available. Fix it by extending `UBOOT_MAKE_FLAGS` variable in all device recipes. Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 481339a0426698adaa0254b479807efde0428de9)
* realtek: add support for ZyXEL GS1900-24ERaylynn Knight2022-06-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24E * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB Macronix MX25L12835F * RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE * Ethernet: 24x 10/100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 24 ethernet port link/activity LEDs (green, SoC controlled) * Buttons: 1 "RESET" button on front panel * Switch: 1 Power switch on rear of device * Power 120-240V AC C13 * UART: 1 serial header (JP2) with populated standard pin connector on the left side of the PCB. Pinout (front to back): + Pin 1 - VCC marked with white dot + Pin 2 - RX + Pin 3 - TX + PIn 4 - GND Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware * Select the HTTP radio button * Select the Active radio button * Use the browse button to locate the realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin file and select open so File Path is updated with filename. * Select the Apply button. Screen will display "Prepare for firmware upgrade ...". *Wait until screen shows "Do you really want to reboot?" then select the OK button * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24E is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Raylynn Knight <rayknight@me.com> (cherry picked from commit b515ad10a6e1bd5c5da0ea95366fb19c92a75dea)
* ipq806x: add support for Arris TR4400 v2 / RAC2V1ARodrigo Balerdi2022-05-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specs: SoC: Qualcomm IPQ8065 (dual core Cortex-A15) RAM: 512 MB DDR3 Flash: 256 MB NAND, 32 MB NOR WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz Switch: QCA8337 Ethernet: 5x 10/100/1000 Mbit/s USB: 1x USB 3.0 Type-A Buttons: WPS, Reset Power: 12 VDC, 2.5 A Ethernet ports: 1x WAN: connected to eth2 4x LAN: connected via the switch to eth0 and eth1 (eth0 is disabled in OEM firmware) MAC addresses (OEM and OpenWrt): fw_env @ 0x00 d4:ab:82:??:??:?a LAN (eth1) fw_env @ 0x06 d4:ab:82:??:??:?b WAN (eth2) fw_env @ 0x0c d4:ab:82:??:??:?c WLAN 2.4 GHz (ath1) fw_env @ 0x12 d4:ab:82:??:??:?d WLAN 5 GHz (ath0) fw_env @ 0x18 d4:ab:82:??:??:?e OEM usage unknown (eth0 in OpenWrt) OID d4:ab:82 is registered to: ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US More info: https://openwrt.org/inbox/toh/arris/tr4400_v2 IMPORTANT: This port requires moving the 'fw_env' partition prior to first boot to consolidate 70% of the usable space in flash into a contiguous partition. 'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords. Its contents must be copied to 'rootfs_1' prior to booting via initramfs. Note that the stock 'fw_env' partition will be wiped during sysupgrade. A writable 'stock_fw_env' partition pointing to the old, stock location is included in the port to help rolling back this change if desired. Installation: - Requires serial access and a TFTP server. - Fully boot stock, press ENTER, type in: mtd erase /dev/mtd21 dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21 umount /config && ubidetach -m 23 && mtd erase /dev/mtd23 - Reboot and interrupt U-Boot by pressing a key, type in: set mtdids 'nand0=nand0' set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)' set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm' env save - Setup TFTP server serving initramfs image as 'recovery.bin', type in: set ipaddr 192.168.1.1 set serverip 192.168.1.2 tftpboot recovery.bin && bootm - Use sysupgrade to install squashfs image. This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> [add 5.15 changes for 0069-arm-boot-add-dts-files.patch] Signed-off-by: Sungbo Eo <mans0n@gorani.run> (cherry picked from commit f8b0010dfb548469686049f85076fd6a3a6bca2e)
* realtek: add support for ZyXEL GS1900-16Raylynn Knight2022-05-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-16 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB Macronix MX25L12835F * RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE * Ethernet: 16x 10/100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 16 ethernet port link/activity LEDs (green, SoC controlled) * Buttons: 1 "RESET" button on front panel * Power 120-240V AC C13 * UART: 1 serial header (J12) with populated standard pin connector on the right back of the PCB. Pinout (front to back): + Pin 1 - VCC marked with white dot + Pin 2 - RX + Pin 3 - TX + PIn 4 - GND Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware * Select the HTTP radio button * Select the Active radio button * Use the browse button to locate the realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin file amd select open so File Path is update with filename. * Select the Apply button. Screen will display "Prepare for firmware upgrade ...". *Wait until screen shows "Do you really want to reboot?" then select the OK button * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-16 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Raylynn Knight <rayknight@me.com> [removed duplicate patch title, align RAM specification] Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit 580723e86ae53f14273ff8c3a0ebf5d15b4ce1f1)
* ramips: add support for YunCore AX820/HWAP-AX820Clemens Hopfer2022-05-171-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> (cherry picked from commit 4891b865380e2b7f32acf0893df9c1ca9db8d4ea)
* uboot-fritz4040: Add support for Toshiba NANDChristian Lamparter2022-05-151-3/+3
| | | | | | | | | | | | | From Andreas Böhler: "Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in contrast to the Macronix NAND with 4 bit ECC.". Uboot needs to know this in order to have a chance to load from the NAND. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 057bac2e1fc796fb4b2440a896be43bca138be84)
* uboot-envtools: add WS-AP3825i configDavid Bauer2022-04-261-0/+4
| | | | | | | | Add configuration to use uboot-envtools with the Extreme Networks WS-AP3825i. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit fb7ff6b027d1c69e97e6d39e688a969c164065c8)
* uboot-mediatek: remove '0x' prefix from pstore nodeDaniel Golle2022-04-231-1/+1
| | | | | | | | | Remove '0x' prefix from pstore node in dts, just like it was done for the device tree used by Linux on MT7622. This change is done in preparation to update U-Boot to 2022.04. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 810b48e79389a54b9b332fa2834360602a9734f3)
* realtek: add ZyXEL GS1900-24HP v1 supportMartin Kennedy2022-04-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24HP v1 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: * 1 PWR LED (green, not configurable) * 1 SYS LED (green, configurable) * 24 ethernet port link/activity LEDs (green, SoC controlled) * 24 ethernet port PoE status LEDs * 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: * 1 "RESET" button on front panel (soft reset) * 1 button ('SW1') behind right hex grate (hardwired power-off) * PoE: * Management MCU: ST Micro ST32F100 Microcontroller * 6 BCM59111 PSE chips * 170W power budget * Power: 120-240V AC C13 * UART: Internal populated 10-pin header ('J5') providing RS232; connected to SoC UART through a TI or SIPEX 3232C for voltage level shifting. * 'J5' RS232 Pinout (dot as pin 1): 2) SoC RXD 3) GND 10) SoC TXD Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24HP v1 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only be installed in the first partition anyway (hardcoded in the DTS). To ensure we are set to boot from the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin Signed-off-by: Martin Kennedy <hurricos@gmail.com> [Add info on PoE hardware to commit message] Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit a5ac8ad0ba9df50bdd0dda1dc26cf36f83006893)
* ath79: add support for Sophos AP100/AP55 familyAndrew Powers-Holmes2022-04-191-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access points based on the Qualcomm QCA9558 SoC. They share PCB designs with several devices that already have partial or full support, most notably the Devolo DVL1750i/e. The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however the 55 models' ART does not contain calibration data for their third chain despite it being present on the PCB. Specifications common to all models: - Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor) - 128 MB RAM - 16 MB SPI flash - 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in - Green and Red status LEDs sharing a single external light-pipe - Reset button on PCB[1] - Piezo beeper on PCB[2] - Serial UART header on PCB - Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC Unique to AP100 and AP100C: - 3T3R 2.4GHz 802.11b/g/n via SoC WMAC - 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express) AP55 and AP55C: - 2T2R 2.4GHz 802.11b/g/n via SoC WMAC - 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express) AP100 and AP55: - External RJ45 serial console port[3] - USB 2.0 Type A port, power controlled via GPIO 11 Flashing instructions: This firmware can be flashed either via a compatible Sophos SG or XG firewall appliance, which does not require disassembling the device, or via the U-Boot console available on the internal UART header. To flash via XG appliance: - Register on Sophos' website for a no-cost Home Use XG firewall license - Download and install the XG software on a compatible PC or virtual machine, complete initial appliance setup, and enable SSH console access - Connect the target AP device to the XG appliance's LAN interface - Approve the AP from the XG Web UI and wait until it shows as Active (this can take 3-5 minutes) - Connect to the XG appliance over SSH and access the Advanced Console (Menu option 5, then menu option 3) - Run `sudo awetool` and select the menu option to connect to an AP via SSH. When prompted to enable SSH on the target AP, select Yes. - Wait 2-3 minutes, then select the AP from the awetool menu again. This will connect you to a root shell on the target AP. - Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc - Run `mtd -r write /tmp/openwrt.bin astaro_image` - When complete, the access point will reboot to OpenWRT. To flash via U-Boot serial console: - Configure a TFTP server on your PC, and set IP address 192.168.99.8 with netmask 255.255.255.0 - Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C' - Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4] - Connect the AP ethernet to your PC's ethernet port - Connect a terminal to the UART at 115200 8/N/1 as usual - Power on the AP and press a key to cancel autoboot when prompted - Run the following commands at the U-Boot console: - `tftpboot` - `cp.b $fileaddr 0x9f070000 $filesize` - `boot` - The access point will boot to OpenWRT. MAC addresses as verified by OEM firmware: use address source LAN label config 0x201a (label) 2g label + 1 art 0x1002 (also found at config 0x2004) 5g label + 9 art 0x5006 Increments confirmed across three AP55C, two AP55, and one AP100C. These changes have been tested to function on both current master and 21.02.0 without any obvious issues. [1] Button is present but does not alter state of any GPIO on SoC [2] Buzzer and driver circuitry is present on PCB but is not connected to any GPIO. Shorting an unpopulated resistor next to the driver circuitry should connect the buzzer to GPIO 4, but this is unconfirmed. [3] This external RJ45 serial port is disabled in the OEM firmware, but works in OpenWRT without additional configuration, at least on my three test units. [4] On AP100/AP55 models the UART header is accessible after removing the device's top cover. On AP100C/AP55C models, the PCB must be removed for access; three screws secure it to the case. Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net> (cherry picked from commit 6f1efb28983758116a8ecaf9c93e1d875bb70af7)
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com> (cherry picked from commit 78c3534645958c123aa82cec9926a34eed5dd5dd)
* ath79: add support for Yuncore A930Thibaut VARÈNE2022-04-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR - 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN) - 2T2R 802.11b/g/n 2.4GHz Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit a05dcb07241aa83a4416b56201e31b4af8518981)
* ath79: add support for Yuncore XD3200Thibaut VARÈNE2022-04-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit c91df224f54fdd44c9c0487a8c91876f5d273164)
* arm-trusted-firmware-mediatek: remove no longer needed Configure stepDaniel Golle2022-04-101-4/+0
| | | | | | | | | As anyway only the default is called now we can as well also just remove the override for Build/Configure. Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10") Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit dffad93d3e34275b87d97724e64447d8bde537ff)
* grub2: add missing licensePaul Spooren2022-04-051-1/+3
| | | | | | | | The PKG_LICENSE field was missing. While at it, normalize the Makefile a bit. Signed-off-by: Paul Spooren <mail@aparcar.org> (cherry picked from commit 839b1ff1fc0d6bcd74131a78fb9286df7f3b7b97)
* uboot-mvebu: backport patch to fix eMMCRobert Marko2022-04-051-0/+64
| | | | | | | | | | | v2022.01 has a regression that broke eMMC usage on most if not all Armada SoC-s, thus breaking boards like uDPU which use eMMC for storage. Fix it by backporting a recent upstream patch. Fixes: 782d4c8306c8 ("uboot-mvebu: update to version 2022.01") Signed-off-by: Robert Marko <robert.marko@sartura.hr> (cherry picked from commit a70383080694f26d13db8341a83261f6b1c45f12)
* uboot-mediatek: add patch to allow accessing bootconf from LinuxDaniel Golle2022-03-271-0/+60
| | | | | | | | | Store selected boot configuration in '/chosen' node in device tree, so it can be accessed by Linux (and used for fine-tuning the FIT partition parser). Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit dfc3ea6810904f4f498d4a1304443c1a4c9f1e3c)
* uboot-envtools: oxnas: fix wrong eraseblock size for shuttle,kd20Daniel Golle2022-03-271-1/+1
| | | | | | | | | Shuttle KD20 has NAND flash with 0x20000 (128KiB) erase blocks. Correctly set that in uboot-envtools as well to allow writing to the bootloader environment using fw_setenv. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit fa676395136b17d753fd90137e58f02a4fcdb09e)
* mediatek: Add support for Xiaomi Redmi Router AX6SRichard Huynh2022-03-211-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Also known as the "Xiaomi Router AX3200" in western markets, but only the AX6S is widely installation-capable at this time. SoC: MediaTek MT7622B RAM: DDR3 256 MiB (ESMT M15T2G16128A) Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG) WLAN: 2.4/5 GHz 4T4R 2.4 GHz: MediaTek MT7622B 5 GHz: MediaTek MT7915E Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531B LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin) UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8 Power: 12 VDC, 1.5 A Notes: U-Boot passes through the ethaddr from uboot-env partition, but also has been known to reset it to a generic mac address hardcoded in the bootloader. However, bdata is also populated with the ethernet mac addresses, but is also typically never written to. Thus this is used instead. Installation: 1. Flash stock Xiaomi "closed beta" image labelled 'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'. (MD5: 5eedf1632ac97bb5a6bb072c08603ed7) 2. Calculate telnet password from serial number and login 3. Execute commands to prepare device nvram set ssh_en=1 nvram set uart_en=1 nvram set boot_wait=on nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit 4. Download and flash image On computer: python -m http.server On router: cd /tmp wget http://<IP>:8000/factory.bin mtd -r write factory.bin firmware Device should reboot at this point. Reverting to stock: Stock Xiaomi recovery tftp that accepts their signed images, with default ips of 192.168.31.1 + 192.168.31.100. Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img) Triggered by holding reset pin on powerup. A simple implementation of this would be via dnsmasq's dhcp-boot option or using the vendor's (Windows only) recovery tool available on their website. Signed-off-by: Richard Huynh <voxlympha@gmail.com> (cherry picked from commit 9f9477b2751231d57cdd8c227149b88c93491d93)
* ramips: add support for Beeline SmartBox FlashMikhail Zhilkin2022-03-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Winbond W632GU6NB Flash: 128 MiB (NAND), Winbond W29N01HVSINF Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: 1xUSB3.0 Button: 1 (Reset/WPS) LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WE42022 Installation ------------ 1. Place *factory.trx on any web server (192.168.1.2 in this example) 2. Connect to the router using telnet shell (no password required) 3. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 4. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 5. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 6. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 reboot Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | 30:xx:xx:51:xx:09 | No MACs was | | LAN | 30:xx:xx:51:xx:09 | found on Flash | | WAN | 30:xx:xx:51:xx:06 | [1] | | WLAN_2g | 30:xx:xx:51:xx:07 | | | WLAN_5g | 32:xx:xx:41:xx:07 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in "Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several Smartbox Flash devices even within the same broadcast domain. Stock firmware image format --------------------------- +--------------+---------------+----------------------------------------+ | Offset | 1.0.15 | Description | +==============+===============+========================================+ | 0x0 | 5d 43 6f 74 | TRX magic "]Cot" | +--------------+---------------+----------------------------------------+ | 0x4 | 00 70 ff 00 | Length (reverse) | +--------------+---------------+----------------------------------------+ | | | htonl(~crc) from 0xc ("flag_version") | | 0x8 | 72 b3 93 16 | to "Length" | +--------------+---------------+----------------------------------------+ | 0xc | 00 00 01 00 | Flags | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of Kernel partition | | 0x10 | 1c 00 00 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of RootFS partition | | 0x14 | 00 00 42 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | 0x18 | 00 00 00 00 | Zeroes | +--------------+---------------+----------------------------------------+ | 0x1c | 27 05 19 56 … | Kernel data + zero padding | +--------------+---------------+----------------------------------------+ | | | RootFS data (starting with "hsqs") + | | 0x420000 | 68 73 71 73 … | zero padding to "Length" | +--------------+---------------+----------------------------------------+ | | | Some signature data (format is | | | | unknown). Necessary for the fw | | "Lenght" | 00 00 00 00 … | update via oem fw web interface. | +--------------+---------------+----------------------------------------+ | "Lenght" + | | TRX magic "HDR0". U-Boot is | | 0x10c | 48 44 52 30 | checking it at every boot. | +--------------+---------------+----------------------------------------+ | | | 1.00: | | | | Zero padding to ("Lenght" + 0x23000) | | | | 1.0.12: | | | | Zero padding to ("Lenght" + 0x2a000) | | "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: | | 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* uboot-bcm4908: add BCM4912 buildRafał Miłecki2022-03-153-3/+33
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* uboot-bcm4908: update to the latest genericRafał Miłecki2022-03-151-3/+3
| | | | | | | 0625aad74d arm: dts: add ASUS GT-AX6000 6fb1cb624d arm: dts: add Netgear RAXE450 / RAXE550 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* uboot-bcm4908: use "xxd" from staging_dirRafał Miłecki2022-03-151-4/+4
| | | | | | | | This fixes: bash: xxd: command not found on hosts without xxd installed. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: add support for Araknis AN-700-AP-I-ACMichael Pratt2022-03-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: 2AG6R-AN700APIAC Araknis AN-700-AP-I-AC is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP1750 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails **Specification:** - QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3 - QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state **MAC addresses:** MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH *:xb art 0x0 phy1 2.4G *:xc --- phy0 5GHz *:xd --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times **Format of OEM firmware image:** The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Araknis AN-500-AP-I-ACMichael Pratt2022-03-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: 2AG6R-AN500APIAC Araknis AN-500-AP-I-AC is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP1200 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails **Specification:** - QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2 - QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state **MAC addresses:** MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH *:e1 art 0x0 phy1 2.4G *:e2 --- phy0 5GHz *:e3 --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times **Format of OEM firmware image:** The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Araknis AN-300-AP-I-NMichael Pratt2022-03-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: U2M-AN300APIN Araknis AN-300-AP-I-N is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EWS310AP the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails **Specification:** - AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2 - AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2 - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM 1839ZFG V59C1512164QFJ25 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state **MAC addresses:** MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH *:7d art 0x0 phy1 2.4G *:7e --- phy0 5GHz *:7f --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times **Format of OEM firmware image:** The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* realtek: add ZyXEL GS1900-24 v1 supportMartin Kennedy2022-03-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24 v1 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: * 1 PWR LED (green, not configurable) * 1 SYS LED (green, configurable) * 24 ethernet port link/activity LEDs (green, SoC controlled) * 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: * 1 "RESET" button on front panel (soft reset) * 1 button ('SW1') behind right hex grate (hardwired power-off) * Power: 120-240V AC C13 * UART: Internal populated 10-pin header ('J5') providing RS232; connected to SoC UART through a SIPEX 3232EC for voltage level shifting. * 'J5' RS232 Pinout (dot as pin 1): 2) SoC RXD 3) GND 10) SoC TXD Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on > Since the GS1900-24 v1 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only be installed in the first partition anyway (hardcoded in the DTS). To ensure we are set to boot from the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin Signed-off-by: Martin Kennedy <hurricos@gmail.com>
* uboot-bcm4908: add package with BCM4908 U-BootRafał Miłecki2022-03-114-0/+181
| | | | | | | New BCM4908 devices come with U-Boot instead of CFE. Firmwares for such devices has to include U-Boot. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-03 20:19:35 +0000