aboutsummaryrefslogtreecommitdiffstats
path: root/package/boot
Commit message (Collapse)AuthorAgeFilesLines
* uboot-sunxi: add support for FriendlyARM NanoPi R1S H5Chukun Pan2021-10-302-0/+281
| | | | | | | Merged in https://github.com/u-boot/u-boot/commit/e7510d2, adjust back to the current 2020.04 version. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* at91: add support for sam9x60-ek boardClaudiu Beznea2021-10-242-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for SAM9X60-EK board. Hardware: - SoC: SAM9X60 - RAM: Winbond W972GG6KB-25 (2Gbit DDR2) - NAND Flash: Micron MT29F4G08ABAEA - QSPI Flash: Microchip SST26VF064B - EEPROM: Microchip 24AA02E48 - SDMMC: One standard 4-bit SD card interface - USB: two stacked Type-A connectors with power switches, one micro-B USB device - CAN: 2 interfaces (Microchip MCP2542) - Ethernet: one 10/100Mbps - WiFi/BT: one optional WiFi/Bluetooth interface - Audio: one ClassD port - Display: one 24-bit LCD interface - Camera: one 12-bit image sensor interface - IO: one IO expander (Microchip MCP23008) - Debug ports: one J-Link-OB + CDC, one JTAG interface - Leds: one RGB LED - Buttons: 4 push button switches - Expansion: one PIO connector, one mikrobus connector - Power management: two power regulators, two power consumption measurement devices Flashing: - follow the procedure at [1] [1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
* at91: add support for sama5d27-wlsom1-ek boardClaudiu Beznea2021-10-242-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for SAMA5D27 WLSOM1-EK board. Hardware: - SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM - MMC: one standard SD card interface - Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF) with embedded EUI-48 and EUI-64 MAC addresses - USB: one USB device, one USB host one HSIC interface - Ethernet: 1x10/100Mbps port - WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module (ATWILC3000-MR110UA) - Crypto: one ATECC608B-TNGTLS secure element - Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface - Debug port: one JTAG interface, one UART interface, one WILC UART interface - Leds: one RGB LED - Buttons: start, reset, wakeup, user buttons - Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC connector - Power managament: PMIC (MCP16502) Flashing: - follow procedure at [1] [1] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
* at91: add support for sama5d2 icp boardClaudiu Beznea2021-10-242-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for SAMA5D2 ICP board. Hardware: - SoC: SAMA5D27 - RAM: 512 MB DDR3L - MMC: One stanard SD card interface - USB: One USB host switch 4 ports with power switch, One USB device type Micro-AB - CAN: 2 interfaces - Ethernet: One Gigabit Ethernet PHY through HSIC, One ETH switchport, One EtherCAT interface - WiFi/BT: Footprint for IEEE 802.11 b/g/n Wi-Fi plus Bluetooth module (Wi-Fi/BT), suitable for Microchip WILC3000-MR110CA or WILC3000-MR110UA - Debug port: One J-Link-OB/J-Link-CDC, one JTAG interface - Leds: one RGB LED - Buttons: reset, wakeup, 2 user buttons - Expansion: one PIOBU/PIO connector, 3 mikrobus sockets - Power mangament: PMIC (MCP16502), one power consumption device (PAC1934) Not working in Linux: - EtherCAT interface: there is no Linux support integrated - PAC1934: driver available at [1] but not integrated in Linux Flashing: - follow the procedure at [2] [1] https://ww1.microchip.com/downloads/en/DeviceDoc/pac193x_linux_driver.zip [2] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage#Create_a_SD_card_with_the_demo Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
* u-boot.mk: always link host libraries staticAndre Heider2021-10-243-42/+0
| | | | | | | | Host libraries are only build static, so let's pass --static to pkg-config globally and remove the then unnecessary patches doing exactly that individually. Signed-off-by: Andre Heider <a.heider@gmail.com>
* u-boot.mk: fix pkg-config usageAndre Heider2021-10-244-8/+0
| | | | | | | | Using Host/Exports doesn't work as intended, explicitly add the required vars so that u-boot finds the required libraries when building its tools. Signed-off-by: Andre Heider <a.heider@gmail.com>
* rockchip: rename "Rock Pi 4" to "Rock Pi 4A"Adrian Schmutzler2021-10-101-1/+1
| | | | | | | | | | | | Kernel has added the different variants of the Rock Pi 4 in commit b5edb0467370 ("arm64: dts: rockchip: Mark rock-pi-4 as rock-pi-4a dts"). The former Rock Pi 4 is now Rock Pi 4A. For compatibility with kernel 5.4, this rename has been held back so far. Having switched to kernel 5.10 now, we can finally apply it in our tree as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* uboot-mediatek: update to 2021.10Daniel Golle2021-10-0432-610/+77
| | | | | | | | | | | U-Boot 2021.10 has been released. Rebase mediatek patches on top of new release and remove some patches which have been merged upstream. Tested on Bananapi BPi-R2 (mt7623), Bananapi BPi-R64 (mt7622) and Linksys E8450 (mt7622). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* treewide: use AUTORELEASE on all uboot-* packagesAdrian Schmutzler2021-10-0210-10/+10
| | | | | | | | Nobody ever updates PKG_RELEASE when changing devices or setup in the various uboot-* packages. Use $(AUTORELEASE) so we still have proper versioning there. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: add Globalscale MOCHAbinRobert Marko2021-10-021-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Globalscale MOCHAbin is a Armada 7040 based development board. Specifications: * Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz * 2 / 4 / 8 GB of DDR4 DRAM * 16 GB eMMC * 4MB SPI-NOR (Bootloader) * 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only) * 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only) * 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C) * 1x SATA 7+15 socket (SATA3) * 1x 16-pin (2×8) MikroBus Connector * 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots) * 2x USB3.0 Type-A ports via SMSC USB5434B hub * Cortex 2x5 JTAG * microUSB port for UART (PL2303GL/PL2303SA onboard) * 1x 10G SFP+ * 1x 1G SFP (Connected to 88E1512 PHY) * 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY) * 4x 1G RJ45 ports via Topaz 88E6141 switch * RTC with battery holder (SoC provided, requires CR2032 battery) * 1x 12V DC IN * 1x Power switch * 1x 12V fan header (3-pin, power only) * 1x mini-PCIe LED header (2x0.1" pins) * 1x M.2-2280 LED header (2x0.1" pins) * 6x Bootstrap jumpers * 1x Power LED (Green) * 3x Tri-color RGB LEDs (Controllable) * 1x Microchip ATECC608B secure element Note that 1G SFP and 1G WAN cannot be used at the same time as they are in parallel connected to the same PHY. Installation: Copy dtb from build_dir to bin/ and run tftpserver there: $ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/ $ in.tftpd -L -s bin/targets/mvebu/cortexa72/ Connect to the device UART via microUSB port and power on the device. Power on the device and hit any key to stop the autoboot. Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g: $ setenv serverip 192.168.1.10 # Host $ setenv ipaddr 192.168.1.15 # Device Set the ethernet device (Example for the 1G WAN): $ setenv ethact mvpp2-2 Ping server to confirm network is working: $ ping $serverip Using mvpp2-2 device host 192.168.1.15 is alive Tftpboot the firmware: $ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin $ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb Boot the image: $ booti $kernel_addr_r - $fdt_addr_r Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz to /tmp dir on the device. Gunzip and dd the image: $ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz $ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync Reboot the device. Hit any key to stop the autoboot. Reset U-boot env and set the bootcmd: $ env default -a $ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}' Optionally I would advise to edit the console env variable to remove earlycon as that causes the kernel to never use the driver for the serial console. Earlycon should be used only for debugging before the kernel can configure the console and will otherwise cause various issues with the console. $ setenv console 'console=ttyS0,115200' Save and reset $ saveenv $ reset OpenWrt should boot from eMMC now. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* uboot-lantiq: fix sha1.h header clash when system libmd installedAlan Swanson2021-10-021-0/+172
| | | | | | | | Backport of u-boot commit "includes: move openssl headers to include/u-boot" https://github.com/u-boot/u-boot/commit/2b9912e6a7df7b1f60beb7942bd0e6fa5f9d0167 Fixes: FS#3955 Signed-off-by: Alan Swanson <reiver@improbability.net>
* uboot-mediatek: fix and make use of LEDs on BPi-R2Daniel Golle2021-09-302-5/+36
| | | | | | | Fix BPi-R2 GPIO LEDs to indicate boot into production or recovery firmware in DTS and define them in default environment. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* tfp-layerscape: update to LSDK-20.12Rosen Penev2021-09-213-10/+23
| | | | | | | | | | Fixes compilation with GCC11. Kept PKG_VERSION as there's some bug that chops off the 12 at the end. Refreshed other patch. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* arm-trusted-firmware-mvebu: Add hash for aarch64 cm3-gccHauke Mehrtens2021-09-201-0/+4
| | | | | | | | This adds the hash also for the aarch64 toolchain in addition to the x86_64 toolchain. This gets the build on a Linux aarch64 host one step further. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* arm-trusted-firmware-mvebu: CZ.NIC's Secure Firmware bump to v2021.09.07sean lee2021-09-154-168/+2
| | | | | | | | | | | | | | | | | bump version and remove patches that have been applied 176d701 wtmi: Wait 1s after putting PHYs INTn pin low 2eeccfe wtmi: Change comment describing reset workaround e8c94a5 wtmi: Count RAM size from both CS0 and CS1 995979e wtmi: Rename macro e29eb29 wtmi: soc: Fix start_ap_workaround() for TF-A with debug 81245ed wtmi: Use constant name PLAT_MARVELL_MAILBOX_BASE 18ccb83 wtmi: Do a proper UART reset with clock change as described in spec 15ff106 avs: Validate VDD value from OTP 3f33626 fix: clock: a3700: change pwm clock for 600/600 and 1200/750 preset fb5e436 wtmi: uart: fix UART baudrate divisor calculation Signed-off-by: sean lee <ilf@live.com>
* realtek: add ZyXEL GS1900-24HPv2 supportSoma Zambelly2021-09-131-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24HPv2 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: W631GG8MB-12 128 MiB DDR3 SDRAM (stock firmware is configured to use only 64 MiB) * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 24 ethernet port link/activity LEDs (green, SoC controlled) 24 ethernet port PoE status LEDs 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: 1 "RESTORE" button on front panel 1 "RESET" button on front panel * Power 120-240V AC C13 * UART: 1 serial header (J41) with populated standard pin connector on the left edge of the PCB, angled towards the side. The casing has a rectangular cutout on the side that provides external access to these pins. Pinout (front to back): + GND + TX + RX + VCC Serial connection parameters for both devices: 115200 8N1. Installation ------------ OEM upgrade method: (Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged) * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
* ramips: add support for Sitecom WLR-4100 v1 002Andrea Poletti2021-09-051-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router Specification: SoC: MT7620A RAM: 64 MB DDR2 Flash: MX25L6405D SPI NOR 8 MB WIFI: 2.4 GHz integrated Ethernet: 5x 10/100/1000 Mbps QCA8337 USB: 1x 2.0 LEDS: 2x GPIO controlled, 5x switch Buttons: 1x GPIO controlled UART: row of 4 unpopulated holes near USB port, starting count from white triangle on PCB: VCC 3.3V GND TX RX baud: 115200, parity: none, flow control: none Installation Connect to one of LAN (yellow) ethernet ports, Open router configuration interface, Go to Toolbox > Firmware, Browse for OpenWrt factory image with dlf extension and hit Apply, Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Known issues Some USB 2.0 devices work at full speed mode 1.1 only MAC addresses factory partition only contains one (binary) MAC address in 0x4. u-boot-env contains four (ascii) MAC addresses, of which two appear to be valid. factory 0x4 **:**:**:**:b9:84 binary u-boot-env ethaddr **:**:**:**:b9:84 ascii u-boot-env wanaddr **:**:**:**:b9:85 ascii u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii The factory firmware only assigns ethaddr. Thus, we take the binary value which we can use directly in DTS. Additional information OEM firmware shell password is: SitecomSenao useful for creating backup of original firmware. There is also another revision of this device (v1 001), based on RT3352 SoC Signed-off-by: Andrea Poletti <polex73@yahoo.it> [remove config DT label, convert to nvmem, remove MAC address setup from u-boot-env, add MAC address info to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* uboot-mediatek: pass console=tty1 for BPi-R2Daniel Golle2021-08-211-1/+1
| | | | | | | BananaPi BPi-R2 comes with HDMI and MIPI-DSI. Use dislpay facility in Linux by add "console=tty1" boot argument. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* at91bootstrap: Fix compile with binutils 2.36Hauke Mehrtens2021-08-211-0/+38
| | | | | | | This fixes a build problem seen after binutils 2.36 is used by default. Fixes: 3f41153b1c28 ("toolchain/binutils: switch to version 2.36.1 by default") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-at91: fix dtc compilation on host gcc 10Hauke Mehrtens2021-08-212-9/+49
| | | | | | Backport a patch from upstream U-Boot to fix the compile with host GCC 10. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-rockchip: update to v2021.07David Bauer2021-08-155-310/+70
| | | | | | Tested on NanoPi R2S Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-layerscape: fix dtc compilation on host gcc 10Hauke Mehrtens2021-08-091-0/+46
| | | | | | Backport a patch from upstream U-Boot to fix the compile with host GCC 10. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* arm-trusted-firmware-mvebu: switch to CZ.NIC's Secure FirmwareAndre Heider2021-07-256-0/+215
| | | | | | | | | | | | | | | | | CZ.NIC as part of Turris project released free and open source WTMI application firmware wtmi_app.bin for all Armada 3720 devices. This firmware includes additional features like access to Hardware Random Number Generator of Armada 3720 SoC which original Marvell's fuse.bin image does not have. Add a patch which allows to pass the commit id, so the firmware is able to identify itself, see a04bffeb. Add a patch to disable linking with gold, since the ARM toolchain doesn't ship gold. Cherry-pick the 3 post-release fixes. Signed-off-by: Andre Heider <a.heider@gmail.com>
* arm-trusted-firmware-mvebu: update CM3 toolchain to v10.2Andre Heider2021-07-251-12/+12
| | | | | | | Linaro stopped shipping binary toolchains quite some time ago, switch over to the ARM builds. Signed-off-by: Andre Heider <a.heider@gmail.com>
* arm-trusted-firmware-mvebu: update mv-ddr-marvell to current masterAndre Heider2021-07-251-3/+3
| | | | | | | | | | | | | 02e23db fix compilation errors popped up by GCC-10 7c35173 Merge pull request #29 from pali/sync-a38x-uboot bb734f5 mv_ddr: a38x: Use SOC_REGS_PHY_BASE for INTER_REGS_BASE ee1ea84 mv_ddr: a38x: Fix ddr3 compilation 70f3e2e mv_ddr: Fix comment typo dd960b4 mv_ddr: ddr3: Allow boards to specify CK_DELAY parameter a87f4f7 mv_ddr: ddr3: only use active chip-selects when tuning ODT 3defcec mv_ddr: a38x: Add support for setting timing in hws_topology_map Signed-off-by: Andre Heider <a.heider@gmail.com>
* arm-trusted-firmware-mvebu: update a3700-tools to current masterAndre Heider2021-07-252-8/+9
| | | | | | | | | | | | | | | | | | | 2efdb10 wtmi: Fix calculation of UART divider 4247e39 fix: twin die ddr porting guide 8ad7992 sys_init: Add missing newlines in debug mode 4ddea19 avs: Validate VDD value from OTP c444aeb avs: Fix description for avs value 0x2e 1915b78 tim: Optimize code generated by gettimver.sh and print newline 21f566d tim: Print mv_ddr version and configuration on UART 840b70b tim: Use variable $DDRFILE where possible c10e6ae tim: Fix waiting for UART TX ready 7bf95cf wtmi: Wait 3ms for the TX on UART to be empty prior resetting TX FIFO 63e8433 wtmi: Add "dirty" suffix to git commit and rebuild sys_init.bin binary when VERSION changes e949b58 wtmi: During setup clock phase print CPU and DDR speed 10376b5 wtmi: Flush output on UART after the '\n' character 509c647 Makefile: Check that specified DDR_TOPOLOGY option is valid Signed-off-by: Andre Heider <a.heider@gmail.com>
* arm-trusted-firmware-mvebu: update to v2.5Andre Heider2021-07-256-4/+441
| | | | | | | | | | | Revert to using the checked in `tbb_linux` image tool binary since building it drags in the rather big Crypto++ project. Cherry-pick the post-release UART fixes. Switch to AUTORELEASE while at it. Signed-off-by: Andre Heider <a.heider@gmail.com>
* arm-trusted-firmware-mvebu: remove unpacked sources upon cleanAndre Heider2021-07-251-0/+7
| | | | | | These are all unpacked in the Build/Prepare step, clean up accordingly. Signed-off-by: Andre Heider <a.heider@gmail.com>
* uboot-mvebu: update to v2021.07Andre Heider2021-07-252-4/+4
| | | | | | | Refresh the patches. Switch to AUTORELEASE while at it. Signed-off-by: Andre Heider <a.heider@gmail.com>
* uboot-envtools: mvebu: update uci defaults for Turris OmniaMarek Behún2021-07-251-1/+4
| | | | | | | | | | | | | From version 2021.09 U-Boot will fixup Turris Omnia's DTB before booting, separating U-Boot's environment into separate MTD partition "u-boot-env" [1]. Check if "u-boot-env" MTD partition exists and set the uci defaults accordingly. [1] https://lists.denx.de/pipermail/u-boot/2021-July/455017.html Signed-off-by: Marek Behún <marek.behun@nic.cz>
* uboot-mediatek: fix board name of Bananapi BPi-R2Daniel Golle2021-07-201-1/+1
| | | | | | | | As the board name was changed to be identical to the device tree compatible string (just like for other boards), also reflect that change for U-Boot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: add configuration for Bananapi BPi-R2Daniel Golle2021-07-201-0/+25
| | | | | | | | Add fw_env configuration for the BPi-R2 which is a mediatek/mt7623 devboard which can be booted from SD Card or eMMC. Auto detect the boot device and add environment accordingly. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: move mediatek to mediatek_mt7622Daniel Golle2021-07-201-0/+0
| | | | | | | | All mediatek boards having fw_env accessible through uboot-envtools belong to be mt7622 subtarget. Move the file, as subtarget-specific files are supported for a while now. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: rework support for the BPi-R2Daniel Golle2021-07-202-13/+301
| | | | | | | | | * use built-in default environment instead of file in bootfs * get rid of bootfs alltogether and use uImage.FIT * auto-detect boot device like original script did * add support for factory button Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: several fixes for MT7622Daniel Golle2021-07-114-94/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | * ! Behavior change ! Old behavior: If the Reset button is held down during power-on do factory reset and try booting recovery from TFTP forever. If valid recovery is received via TFTP, write it to flash and boot. New behavior: If the Reset button is held down during power-on do factory reset, then try TFTP *once*, then try booting on-flash recovery, then keep trying via TFTP forever until a valid image is received. Only if there is no bootable recovery stored on flash, store the downloaded recovery. Then boot it. * Set loadaddr to 0x48000000 in order to allow booting images larger than ~47MB (reported by Oskari Lemmelä). Setting loadaddr to 0x48000000 gives us 384MB on devices with 512MB RAM, which should be more than enough as a maximum size for uImage.FIT to be loaded. * Widely unify device-specific default environment in preparation to auto-generate it from parameters. * backport upstream commit fixing MBR/DOS partitioning Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Linksys EA8100 v2Tee Hao Wei2021-07-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Tom Wizetek (@wizetek) for testing. Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
* grub2: update to 2.06Dirk Neukirchen2021-06-213-59/+19
| | | | | | | | | | | | | | | -300-CVE-2015-8370.patch is upstreamed with different code (upstream id: 451d80e52d851432e109771bb8febafca7a5f1f2) - fixup OpenWrts setup_root patch compile tested: x86_64,i386 runtime tested: VM x86_64,VM i386 - booted fine - grub-editenv worked Signed-off-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
* grub2: pass compilation parameters more accurately李国2021-06-201-3/+5
| | | | | | | | | In order for the grub2 boot-related code to compile normally, we have made many adjustments to the compilation parameters. These adjustments are not necessary for tools-related code. We apply these parameter adjustments only to the boot-related code. Signed-off-by: 李国 <uxgood.org@gmail.com>
* grub2: make grub2 tools built in a separate variant李国2021-06-201-2/+6
| | | | | | | | | grub2 boot-related code and tools-related code may require different compilation parameters. We split them into different variants for compilation, so that we can accurately pass the required parameters and avoid causing problems. Signed-off-by: 李国 <uxgood.org@gmail.com>
* grub2: make grub2-bios-setup as a separate package李国2021-06-201-8/+23
| | | | | | | | | | The grub2 and grub2-efi packages should only contain boot-related code. grub-bios-setup is the same as grub-editenv, they are both grub2 tools and should be placed in a separate package. Signed-off-by: 李国 <uxgood.org@gmail.com> [use AUTORELEASE and update to SPDX] Signed-off-by: Paul Spooren <mail@aparcar.org>
* uboot-rockchip: add NanoPi R4S supportTianling Shen2021-06-102-0/+301
| | | | | | Add support for the FriendlyARM NanoPi R4S. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-kirkwood: refresh patchesAdrian Schmutzler2021-06-0610-45/+35
| | | | | | | | This is only cosmetic, but the next one adding a patch here would have to do it anyway, and thus will get a smaller diff for review now. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: Add support for SheevaplugBERENYI Balazs2021-06-064-2/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Globalscale SheevaPlug: * Marvell Kirkwood 88F6281 * 512 MB SDRAM * 512 MB Flash * Gigabit Network * USB 2.0 * SD slot * Serial console The device is supported in mainline uboot/linux the commit adds only some openwrt config for building an image. Installation: 1 - Update uboot: setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot u-boot.kwb nand erase 0x0 0x100000 nand write 0x800000 0x0 0x100000 reset 2 - Install OpenWRT: setenv ethaddr 00:50:43:01:xx:xx saveenv setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot openwrt-kirkwood-globalscale_sheevaplug-squashfs-factory.bin nand erase.part ubi nand write 0x800000 ubi 0x600000 reset Signed-off-by: BERENYI Balazs <balazs@wee.hu> Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com> [add vendor name for uboot-kirkwood, merge patches, copy to 5.10, add AUTORELEASE for uboot-kirkwood, refresh patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: add support for Askey RT4230W REV6Lauro Moreno2021-06-051-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Askey RT4230W REV6 (Branded by Spectrum/Charter as RAC2V1K) At this time, there's no way to reinstall the stock firmware so don't install this on a router that's being rented. Specifications: Qualcomm IPQ8065 1 GB of RAM (DDR3) 512 MB Flash (NAND) 2x Wave 2 WiFi cards (QCA9984) 5x 10/100/1000 Mbps Ethernet (Switch: QCA8337) 1x LED (Controlled by a microcontroller that switches it between red and blue with different patterns) 1x USB 3.0 Type-A 12V DC Power Input UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V Port settings are 115200n8 More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830 https://deviwiki.com/wiki/Askey_RAC2V1K To check what revision your router is, restore one of these config backups through the stock firmware to get ssh access then run "cat /proc/device-tree/model". https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17 The revision number on the board doesn't seem to be very consistent so that's why this is needed. You can also run printenv in the uboot console and if machid is set to 177d, that means your router is rev6. Note: Don't install this if the router is being rented from an ISP. The defined partition layout is different from the OEM one and even if you changed the layout to match, backing up and restoring the OEM firmware breaks /overlay so nothing will save and the router will likely enter a bootloop. How to install: Method 1: Install without opening the case using SSH and tftp You'll need: RAC2V1K-SSH.zip: https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip initramfs and sysupgrade images Connect to one of the router's LAN ports Download the RAC2V1K-SSH.zip file and restore the config file that corresponds to your router's firmware (If you're firmware is newer than what's in the zip file, just restore the 1.1.16 file) After a reboot, you should be able to ssh into the router with username: "4230w" and password: "linuxbox" or "admin". Run the following commannds fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as it's in the same subnet as the server fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next steps fw_setenv bootdelay 8 fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq" Don't reboot the router yet. Install and set up a tftp server on your computer Set a static ip on the ethernet interface of your computer (use this for serverip in the above commands) Rename the initramfs image to initramfs.bin, and host it with the tftp server Reboot the router. If you set up everything right, the router led should switch over to a slow blue glow which means openwrt is booted. If for some reason the file doesn't get loaded into ram properly, it should still boot to the OEM firmware. After openwrt boots, ssh into it and run these commands: fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi read 0x44000000 kernel 0x6e0000 && bootm" fw_setenv bootdelay 2 After openwrt boots up, figure out a way to get the sysupgrade file onto it (scp, custom build with usb kernel module included, wget, etc.) then flash it with sysupgrade. After it finishes flashing, it should reboot, the light should start flashing blue, then when the light starts "breathing" blue that means openwrt is booted. Method 2: Install with serial access (Do this if something fails and you can't boot after using method 1) You'll need: initramfs and sysupgrade images Serial access: https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case Install and set up a tftp server Set a static ip on the ethernet interface of your computer Download the initramfs image, rename it to initramfs.bin, and host it with the tftp server Connect the wan port of the router to your computer Interrupt U-Boot and run these commands: setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer) setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet) setenv bootcmd "setenv mtdids nand0=nand0 && set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi read 0x44000000 kernel 0x6e0000 && bootm" saveenv tftpboot initramfs.bin bootm After openwrt boots up, figure out a way to get the sysupgrade file onto it (scp, custom build with usb kernel module included, wget, etc.) then flash it with sysupgrade. After it finishes flashing, it should reboot, the light should start flashing blue, then when the light starts "breathing" blue that means openwrt is booted. Signed-off-by: Lauro Moreno <lmore377@gmail.com> [add entry in 5.10 patch, fix whitespace issues] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA8100 v1Tee Hao Wei2021-06-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2 and EA7500 v2. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Leon Poon (@LeonPoon) for the initial bringup. Signed-off-by: Tee Hao Wei <angelsl@in04.sg> [add missing entry in 10_fix_wifi_mac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Amped Wireless ALLY router and extenderJonathan Sturges2021-06-051-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Amped Wireless ALLY is a whole-home WiFi kit, with a router (model ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are 11ac and based on MediaTek MT7621AT and MT7615N chips. The units are nearly identical, except the Extender lacks a USB port and has a single Ethernet port. Specification: - SoC: MediaTek MT7621AT (2C/4T) @ 880MHz - RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI) - FLASH: 128MB NAND (Winbond W29N01GVSIAA) - WiFi: 2.4/5 GHz 4T4R - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac - Switch: SoC integrated Gigabit Switch - USB: 1x USB3 (Router only) - BTN: Reset, WPS - LED: single RGB - UART: through-hole on PCB. J1: pin1 (square pad, towards rear)=3.3V, pin2=RX, pin3=GND, pin4=TX. Settings: 57600/8N1. Note regarding dual system partitions ------------------------------------- The vendor firmware and boot loader use a dual partition scheme. The boot partition is decided by the bootImage U-boot environment variable: 0 for the 1st partition, 1 for the 2nd. OpenWrt does not support this scheme and will always use the first OS partition. It will set bootImage to 0 during installation, making sure the first partition is selected by the boot loader. Also, because we can't be sure which partition is active to begin with, a 2-step flash process is used. We first flash an initramfs image, then follow with a regular sysupgrade. Installation: Router (ALLY-R1900K) 1) Install the flashable initramfs image via the OEM web-interface. (Alternatively, you can use the TFTP recovery method below.) You can use WiFi or Ethernet. The direct URL is: http://192.168.3.1/07_06_00_firmware.html a. No login is needed, and you'll be in their setup wizard. b. You might get a warning about not being connected to the Internet. c. Towards the bottom of the page will be a section entitled "Or Manually Upgrade Firmware from a File:" where you can manually choose and upload a firmware file. d: Click "Choose File", select the OpenWRT "initramfs" image and click "Upload." 2) The Router will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 3) Log into LuCI as root; there is no password. 4) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 5) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Extender (ALLY-00X19K) 1) This device requires a TFTP recovery procedure to do an initial load of OpenWRT. Start by configuring a computer as a TFTP client: a. Install a TFTP client (server not necessary) b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6 c. Connect the Ethernet to the sole Ethernet port on the X19K. 2) Put the ALLY Extender in TFTP recovery mode. a. Do this by pressing and holding the reset button on the bottom while connecting the power. b. As soon as the LED lights up green (roughly 2-3 seconds), release the button. 3) Start the TFTP transfer of the Initramfs image from your setup machine. For example, from Linux: tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin 4) The Extender will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 5) Log into LuCI as root; there is no password. 6) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 7) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Backup the OEM Firmware: ----------------------- There isn't any downloadable firmware for the ALLY devices on the Amped Wireless web site. Reverting back to the OEM firmware is not possible unless we have a backup of the original OEM firmware. The OEM firmware may be stored on either /dev/mtd3 ("firmware") or /dev/mtd6 ("oem"). We can't be sure which was overwritten with the initramfs image, so backup both partitions to be safe. 1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware. 2) Under "Save mtdblock contents," first select "firmware" and click "Save mtdblock" to download the image. 3) Repeat the process, but select "oem" from the pull-down menu. Revert to the OEM Firmware: -------------------------- * U-boot TFTP: Follow the TFTP recovery steps for the Extender, and use the backup image. * OpenWrt "Flash Firmware" interface: Upload the backup image and select "Force update" before continuing. Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
* ipq40xx: add netgear wac510 supportRobert Marko2021-06-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear WAC510 Insight Managed Smart Cloud Wireless Access Point, an indoor dual-band, dual-radio 802.11ac business-class wireless AP with integrated omnidirectional antennae and two 10/100/1000 Mbps Ethernet ports. For more information see: <https://www.netgear.com/business/wifi/access-points/wac510> Specifications: SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB Flash1: 2 MiB Winbond W25Q16JV SPI-NOR Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port, WAN port active IEEE 802.3af/at PoE in Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1 LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN Serial: Header J2 1 - 3.3 Volt (Do NOT connect!) 2 - TX 3 - RX 4 - Ground WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter! The Serial settings are 115200-8-N-1. Installation via Stock Web Interface: BTW: The default factory console/web interface login user/password are admin/password. In the web interface navigating to Management - Maintenance - Upgrade - 'Firmware Upgrade' will show you what is currently installed e.g.: Manage Firmware Current Firmware Version: V5.0.10.2 Backup Firmware Version: V1.2.5.11 Under 'Upgrade Options' choose Local (alternatively SFTP would be available) then click/select 'Browse File' on the right side, choose openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar and hit the Upgrade button below. After a minute or two your browser should indicate completion printing 'Firmware update complete.' and 'Rebooting AP...'. Note that OpenWrt will use the WAN PoE port as actual WAN port defaulting to DHCP client but NOT allowing LuCI access, use LAN port defaulting to 192.168.1.1/24 to access LuCI. Installation via TFTP Requiring Serial U-Boot Access: Connect to the device's serial port and hit any key to stop autoboot. Upload and boot the initramfs based OpenWrt image as follows: (IPQ40xx) # setenv serverip 192.168.1.1 (IPQ40xx) # setenv ipaddr 192.168.1.2 (IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb (IPQ40xx) # bootm Note: This only runs OpenWrt from RAM and has not installed anything to flash as of yet. One may permanently install OpenWrt as follows: Check the MTD device number of the active partition: root@OpenWrt:/# dmesg | grep 'set to be root filesystem' [ 1.010084] mtd: device 9 (rootfs) set to be root filesystem Upload the factory image ending with .ubi to /tmp (e.g. using scp or tftp). Then flash the image as follows (substituting the 9 in mtd9 below with whatever number reported above): root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi And reboot. Dual Image Configuration: The default U-Boot boot command bootipq uses the U-Boot environment variables primary/secondary to decide which image to boot. E.g. primary=0, secondary=3800000 uses rootfs while primary=3800000, secondary=0 uses rootfs_1. Switching their values changes the active partition. E.g. from within U-Boot: (IPQ40xx) # setenv primary 0 (IPQ40xx) # setenv secondary 3800000 (IPQ40xx) # saveenv Or from a OpenWrt userspace serial/SSH console: fw_setenv primary 0 fw_setenv secondary 3800000 Note that if you install two copies of OpenWrt then each will have its independent configuration not like when switching partitions on the stock firmware. BTW: The kernel log shows which boot partition is active: [ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB) vs. [ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB) Note: After 3 failed boot attempts it automatically switches partition. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [squashed netgear-tar commit into main and rename netgear-tar for now, until it is made generic.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: Add support for OpenMesh A40Sven Eckelmann2021-06-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh A60Sven Eckelmann2021-06-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 3T3R 2.4 GHz Wi-Fi (11n) * 3T3R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8031 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ramips: add support for JCG Q20Chukun Pan2021-05-261-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 08:27:24 +0000