aboutsummaryrefslogtreecommitdiffstats
path: root/package/boot
Commit message (Collapse)AuthorAgeFilesLines
* uboot-mvebu: Fix build with libressl 2.7.2Hauke Mehrtens2018-04-291-0/+14
| | | | | | | When libressl was linked the libpthread was missing, add it in addition. Fixes: 2c192b69163f ("tools/libressl: update to version 2.7.2") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-mxs: Fix build with libressl 2.7.2Hauke Mehrtens2018-04-292-16/+31
| | | | | | | | | When libressl was linked the libpthread was missing, add it in addition. Also make the mxsimage tool to use the OpenSSL 1.1 API for the recent libressl version. Fixes: 2c192b69163f ("tools/libressl: update to version 2.7.2") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-zynq: Fix build with libressl 2.7.2Hauke Mehrtens2018-04-291-0/+14
| | | | | | | When libressl was linked the libpthread was missing, add it in addition. Fixes: 2c192b69163f ("tools/libressl: update to version 2.7.2") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-envtools: add support for ESPRESSObin and MACCHIATObinDamir Samardzic2018-04-251-0/+4
| | | | | | | | Added for convenience. These boards can be used as dev boards running various operating systems from different media, and this simplifies work with U-Boot environment. Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* ipq40xx: add support for OpenMesh A62Sven Eckelmann2018-04-231-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + 802.3at POE+ - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 18-24V passive POE (mode B) * powered only via POE The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. The initramfs image can be started using setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)' tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb set fdt_high 0x85000000 bootm 0x84000000 Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* uboot-envtools: remove makefile duplication for supported targetsFelix Fietkau2018-04-201-47/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uboot-envtools: update to 2018.03Luis Araneda2018-04-186-234/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several changes has been made: + AES support has been removed by upstream commit c6831c7 (2017-11-14) [remove patch "200-fw_env_no_aes.patch"] + Support for UBI volumes has beed added by upstream commit 34255b9 (2017-11-15) [remove patch "300-support-env-in-ubivol-chardev.patch"] + A command line argument has beed added ("-c") to manually indicate the location of the environment configuration file Also, patch "400-u-boot-2015.10-stdint.patch" is no longer necessary, and the config option to enable UBI support has been removed. Size comparisons: fw_printenv size: Target Before After ar71xx 15,189 bytes 18,133 bytes (+2,944 bytes) ipq40xx 20,873 bytes 20,987 bytes (+114 bytes) mvebu 20,881 bytes 20,991 bytes (+110 bytes) ramips 15,128 bytes 18,072 bytes (+2,944 bytes) OPKG package size: Target Before After ar71xx 11,309 bytes 12,875 bytes (+1,566 bytes) ipq40xx 11,772 bytes 13,299 bytes (+1,527 bytes) mvebu 11,609 bytes 13,114 bytes (+1,505 bytes) ramips 10,975 bytes 12,503 bytes (+1,528 bytes) Compile tested: ipq40xx (musl, glibc, gcc5-musl), ar71xx, mvebu, ramips Run tested: ipq40xx (ASUS RT-AC58U) Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* packages/uboot-omap: bugfix: serial using ns16550 fifo not enabledAlexander Couzens2018-04-112-1/+310
| | | | | | | | The serial was working before, but not when doing copy&pasting longer commands in a short time. Fixes: a4def18f29e1 ("uboot-omap: Update to u-boot v2017.01") Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: add U-Boot env support for ALFA Network AC1200RMPiotr Dymacz2018-04-061-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: fix ALFA Network AWUSFREE1 supportPiotr Dymacz2018-04-061-7/+9
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* u-boot-mvebu: update to 2018.03Josua Mayer2018-03-313-136/+2
| | | | | | | | | This release brings various improvements to clearfog support, such as distro-boot. Obsoletes: 0002-clearfog-reset-usom-onboard-1512-phy.patch 0003-clearfog-enable-distro-boot-code.patch Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
* u-boot-mvebu: set configuration options in MakefileJosua Mayer2018-03-313-52/+8
| | | | | | | | | | | CONFIG_* variables can easily be set by overriding Build/Configure. so set NET_RANDOM_ETHADDR=y and CMD_SETEXPR=y here. This replaces the following patches: 0001-clearfog-generate-random-MAC-address.patch 0004-clearfog-enable-setexpr-command-by-default.patch Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
* sunxi: add build for sopineFan Fan2018-03-231-0/+10
| | | | | | This will generate image for Pine64 Sopine board. Signed-off-by: Fan Fan <fkpwolf@gmail.com>
* uboot-sunxi: refresh patchesZoltan HERPAI2018-03-217-12/+12
| | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-sunxi: fix build by adding comparabilities for old dtcHauke Mehrtens2018-03-211-0/+52
| | | | | | | | | We use the dtc from the kernel and that does not have all the options which u-boot would like to use now. make these parameters optional. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> [wigyori@uid0.hu: renamed to 221-compatible-old-dtc.patch from 220-] Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-sunxi: bump again to 2017.11Zoltan HERPAI2018-03-2111-392/+36
| | | | | | | | | | | | | | | Runtime-tested on: - Pine64 (A64) - Orange Pi 2 (H3) - Bananapro (A20) - Olimex A20-Micro (A20) - Pcduino v3 (A20) - Pcduino v2 (A10) Compile-tested on: - all A8/A7/A53 boards Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-kirkwood: update to 2018.03Paul Wassi2018-03-2010-218/+120
| | | | | | | | | | | U-Boot now requires GCC > 5 Catch up with upstream and move some configuration options from the header files to the corresponding defconfig files. Also move some options of patch 010 affecting the whole platform to 010's device only. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* uboot-mxs: fix compile problems related to OpenSSLHauke Mehrtens2018-03-172-1/+36
| | | | | | | | | | | | | | Use the UBOOT_MAKE_FLAGS defined in include/u-boot.mk and do not overwrite them to compile the host tools against the shipped LibreSSL. In addition add a patch to fix a compile problem when compiling the tools against LibreSSL caused by differences in the API between OpenSSL 1.1 and LibreSSL. This should fix the compile problems seen in build bot from time to time by not depending on the host libssl-dev package any more but using the LibreSSL version from OpenWrt. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-mxs: refresh patchesHauke Mehrtens2018-03-171-26/+0
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: add targetJohn Crispin2018-03-144-5/+48
| | | | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
* uboot-imx6: fix build with GCC 7Hauke Mehrtens2018-03-134-5/+1344
| | | | | | | | Backport the compiler support patches from upstream u-boot to this older version to make it compile with GCC 7. This was found by build bot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-fritz4040: fix build with gcc7Felix Fietkau2018-03-121-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: Add subtarget for Cortex A9 buildHauke Mehrtens2018-03-101-0/+1
| | | | | | This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: add support for Turris OmniaRyan Mounce2018-03-101-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Turris Omnia and builds an eMMC sysupgrade image in the same format as the SolidRun ClearFog. An initramfs image in the simple yet Omnia-specific 'medkit' image format is also built in order to ease the initial flashing process. Notable hardware support omissions are support for switching between SFP cage and copper PHY, and RGB LED control. Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used. Specifications: - Marvell Armada 385 1.6GHz dual-core ARMv7 CPU - 1GB DDR3 RAM - 8GB eMMC Flash - 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports) - 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN - 2x USB 3.0 - 12x dimmable RGB LEDs controlled by independent MCU - 3x Mini PCIe slots - Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz) - Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz) - Optional Quectel EC20 Mini PCIe LTE modem Flash instructions: If the U-Boot environment has been modified previously (likely manually via serial console), first use serial to reset the default environment. => env default -a => saveenv Method 1 - USB 'medkit' image w/o serial - Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS. Note that the medkit MUST be named omnia-medkit*.tar.gz - Disconnect other USB devices from the Omnia and connect the flash drive to either USB port. - Power on the Omnia and hold down the rear reset button until 4 LEDs are illuminated, then release. - Wait approximately 2 minutes for the Turris Omnia to flash itself with the temporary image, during which LEDs will change multiple times. - Connect a computer to a LAN port of the Turris Omnia with a DHCP client - (if necessary) ssh-keygen -R 192.168.1.1 - ssh root@192.168.1.1 $ mount /dev/sda1 /mnt $ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself and you can remove the flash drive. Method 2 - TFTP w/ serial - Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy dtb + zImage to your TFTP server (rename if desired) - Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server - Connect serial console and interrupt U-Boot => dhcp => setenv serverip <tftp_server_ip_here> => tftpboot 0x01000000 zImage => tftpboot 0x02000000 dtb => bootz 0x01000000 - 0x02000000 - OpenWrt will now boot from ramdisk - Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/ $ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* uboot-sunxi: add Xunlong Orange Pi PCVitalij Alshevsky2018-02-261-0/+7
| | | | Signed-off-by: Vitalij Alshevsky <v_alshevsky@tut.by>
* uboot-envtools: add support for ALFA Network AWUSFREE1Piotr Dymacz2018-02-221-6/+7
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for YunCore T830Piotr Dymacz2018-02-221-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for Samsung WAM250Piotr Dymacz2018-02-221-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for WHQX E1700AC/E600G/E600GAC v2Piotr Dymacz2018-02-221-0/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* grub2: disable building platform code for target utilityFelix Fietkau2018-02-221-1/+2
| | | | | | It is not used and it was causing a build error with GCC 7.3 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: rename gphy firmwareMathias Kresin2018-02-201-5/+5
| | | | | | | | | | Rename the gphy firmware to match the name requested by kernel 4.14 and update the devicetree source files to use the new name. Update the u-boot lantiq Makefile to be compatible with the new names as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uboot-sunxi: Add Xunlong Orange Pi Zero PlusHauke Mehrtens2018-02-172-1/+158
| | | | | | | This is based on a patch from armbian: https://github.com/armbian/build/blob/master/patch/u-boot/u-boot-sunxi/add-orangepi-zeroplus.patch Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: add support for NanoPi NEO Plus2 boardAntony Antony2018-02-171-0/+9
| | | | | | | | | | | | | | arm64: allwinner: h5: NanoPi NEO Plus2 DT support Add initial DT for NanoPi NEO Plus2 by FriendlyARM - Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU - 1 GB DDR3 RAM - 8GB eMMC flash (Samsung KLM8G1WEPD-B031) - micro SD card slot - Gigabit Ethernet (external RTL8211E-VB-CG chip) - 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module) - 2x USB 2.0 host ports & 2x USB via headers Signed-off-by: Antony Antony <antony@phenome.org>
* uboot-sunxi: add u-boot DT for NanoPi NEO Plus2 boardAntony Antony2018-02-171-0/+165
| | | | | | u-boot upstream commit 6130b1f6bc23 Signed-off-by: Antony Antony <antony@phenome.org>
* uboot-sunxi: dts: Update orange Pi R1 integrationHauke Mehrtens2018-02-172-146/+73
| | | | | | | | This syncs the Orange Pi R1 device tree files with the one from the upstream kernel and also uses the default configuration from the Orange Pi Zero. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Revert "uboot-sunxi: bump to 2017.11"Zoltan HERPAI2018-02-1611-36/+392
| | | | | | | | This reverts commit 805f756d6e4ff5061380baf5e262aec72abcf195. Move back to 2017.07 until we move sunxi to GCC7. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* Revert "uboot-sunxi: refresh patches"Zoltan HERPAI2018-02-166-10/+10
| | | | | | | | This reverts commit f142de5f44bcba8cb0f12e5b1fd26cd9867cf866. Revert until we can move to 2017.11 Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* Revert "uboot-sunxi: fix build by adding comparabilities for old dtc"Zoltan HERPAI2018-02-161-52/+0
| | | | | | | | This reverts commit ef0416666f48e1e7793c4230cec18c8cdd3e1003. Revert until we can move to 2017.11 Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ar71xx: Add eTactica EG-200 supportKarl Palsson2018-02-131-0/+1
| | | | | | | | | | | | | | EG-200 is a DIN rail mountable device with one ethernet port, wifi, an RS-485 port, and an internal USB attached uSD card reader. Two leds, "modbus" and "etactica" are managed by userspace applications in factory firmware. Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Karl Palsson <karlp@etactica.com>
* packages: uboot-mxs: override instead of appending u-boot make flagsMichael Heimpold2018-02-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | This prevents passing down the HOSTCC stuff set in u-boot.mk which results in linking errors against openssl: tools/mxsimage.o: In function `sb_aes_reinit': mxsimage.c:(.text+0x202): undefined reference to `EVP_CIPHER_CTX_reset' tools/mxsimage.o: In function `mxsimage_generate': mxsimage.c:(.text+0x110d): undefined reference to `EVP_MD_CTX_new' mxsimage.c:(.text+0x114f): undefined reference to `EVP_MD_CTX_free' mxsimage.c:(.text+0x11c3): undefined reference to `EVP_MD_CTX_new' mxsimage.c:(.text+0x1323): undefined reference to `EVP_MD_CTX_free' mxsimage.c:(.text+0x134a): undefined reference to `EVP_CIPHER_CTX_reset' tools/mxsimage.o: In function `mxsimage_verify_print_header': mxsimage.c:(.text+0x23ce): undefined reference to `EVP_MD_CTX_new' mxsimage.c:(.text+0x242c): undefined reference to `EVP_MD_CTX_new' mxsimage.c:(.text+0x246b): undefined reference to `EVP_MD_CTX_free' mxsimage.c:(.text+0x24ef): undefined reference to `EVP_CIPHER_CTX_reset' mxsimage.c:(.text+0x2e52): undefined reference to `EVP_MD_CTX_free' collect2: error: ld returned 1 exit status Signed-off-by: Michael Heimpold <mhei@heimpold.de>
* packages: uboot-mxs: bump to 2017.11Michael Heimpold2018-02-132-120/+292
| | | | | | Also update the U-Boot BSP patch for I2SE Duckbill devices. Signed-off-by: Michael Heimpold <mhei@heimpold.de>
* layerscape: support ubifs rootfs in u-boot envYangbo Lu2018-02-135-15/+15
| | | | | | | ls1012ardb/ls1012afrdm/ls1046ardb/ls1088ardb firmwares now use ubifs rootfs. So u-boot env should be set accordingly. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update u-boot to LSDK1712Yangbo Lu2018-02-134-32/+32
| | | | | | | This patch is to update layerscape u-boot to NXP LSDK1712 release. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* kexec-tools: bump version to 2.0.16Philip Prindeville2018-02-115-245/+3
| | | | | | All patches have been integrated upstream. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* kexec-tools: issue warning when dd'ing vmcorePhilip Prindeville2018-02-112-1/+3
| | | | | | | | With no warning, it just looks like the box has hung during boot. We don't want users resetting it without having captured a crashdump. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* uboot-fritz4040: Fix build with HOSTCFLAGSHauke Mehrtens2018-02-111-1/+1
| | | | | | | | | | | | When we provide the HOSTCFLAGS to the U-Boot build it will fail because it can not find the u-boot provided header files any more. Just overwrite and not append the package specific configuration on top of the configuration provided by u-boot.mk. uboot-fritz4040 is based on U-Boot 2012.07 and this problem is probably similar to the problem seen with the lantiq and ar71xx u-boot build. Fixes: df9781a4205 ("u-boot,at91bootstrap: fix incorrect HOSTCPPFLAGS variable") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-mvebu: fix build ; use the build's tools/libresslAlexandru Ardelean2018-02-103-251/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since I have no openssl-dev on my machine, I first get this error: ``` tools/kwbimage.c:21:10: fatal error: openssl/bn.h: No such file or directory #include <openssl/bn.h> ``` After removing the UBOOT_MAKE_FLAGS the next error is: ``` tools/kwbimage.c:40:6: error: conflicting types for ‘EVP_MD_CTX_cleanup’ void EVP_MD_CTX_cleanup(EVP_MD_CTX *ctx) ``` After removing the OpenSSL patches the next error is: ``` HOSTLD tools/dumpimage /usr/bin/ld: cannot find -lssl /usr/bin/ld: cannot find -lcrypto collect2: error: ld returned 1 exit status scripts/Makefile.host:108: recipe for target 'tools/dumpimage' failed make[5]: *** [tools/dumpimage] Error 1 ``` So, the final part is to add the build system's HOST_LDFLAGS to the UBOOT_MAKE_FLAGS. (which was done in the previous commit) Then the image builds. Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
* u-boot,at91bootstrap: fix incorrect HOSTCPPFLAGS variableAlexandru Ardelean2018-02-101-1/+1
| | | | | | | | | | | | | | | | | This would should up as `$$(HOSTCPPFLAGS)` in the host CFLAGS. ``` make --jobserver-fds=3,4 -j -C <openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/u-boot-A10-OLinuXino-Lime/u-boot-2017.07 CROSS_COMPILE=arm-openwrt-linux-muslgnueabi- DTC="<openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/linux-sunxi_cortexa8/linux-4.9.76/scripts/dtc/dtc" HOSTCC="gcc" HOSTCFLAGS='-O2 -I<openwrt>/staging_dir/host/include -I<openwrt>/staging_dir/host/usr/include -I<openwrt>/staging_dir/hostpkg/include -I<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/host/include $$(HOSTCPPFLAGS)' HOSTLDFLAGS="" BL31=<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/image/bl31.bin ``` And then it would complain with: ``` /bin/sh: 1: HOSTCPPFLAGS: not found ``` Also, HOSTCPPFLAGS does not exist. The correct var is HOST_CPPFLAGS. Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
* uboot-sunxi: fix build by adding comparabilities for old dtcHauke Mehrtens2018-02-101-0/+52
| | | | | | | We use the dtc from the kernel and that does not have all the options which u-boot would like to use now. make these parameters optional. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-sunxi: refresh patchesHauke Mehrtens2018-02-106-10/+10
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-12 20:04:14 +0000