| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.
The device is based on Qualcomm/Atheros AR9341 v1.
Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button
Flash instructions:
You have three options:
- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.
- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.
- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:
*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
stat -- Status
sys -- System
wless2 -- 2.4G-Wireless
mgmt -- Management
tree -- Tree
help -- Help
reboot -- Reboot
ens202ext>mgmt
Management
---========= Commands Help =========---
admin -- Administration
mvlan -- Management VLAN settings
snmp -- SNMP settings
backup -- Backup/Restore settings
autorb -- Auto reboot settings
fwgrade -- Firmware upgrade
time -- Time settings
wifisch -- Wifi schedule
log -- Log
diag -- Diagnostics
disc -- Device Discovery
logout -- Logout
help -- Help
exit -- Exit
ens202ext/mgmt>fwgrade
Management --> Firmware upgrade
---========= Commands Help =========---
fwup -- Firmware upgrade
help -- Help
exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin
Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
|
|
|
|
| |
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
|
|
|
|
|
|
|
| |
Add a patchfile that implements distro-boot and is meant to go upstream
Also make the other patches git-am'able for easier maintenance.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
|
|
|
|
| |
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
|
|
|
|
| |
Signed-off-by: Mantas Pucka <mantas@8devices.com>
|
|
|
|
|
|
|
|
|
|
| |
Add support for SolidRun ClearFog Base board.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
|
|
|
|
|
|
| |
The conventional model is now known as the "Clearfog Pro"
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
|
|
|
|
|
|
| |
It's disabling thumb for the whole omap3 family.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
|
|
|
|
|
|
|
|
| |
Even it's unknown if it's booting with thumb, because the lack of hardware.
Enable it for now, so the build succeed, because without thumb it can not fit
into spl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
|
|
|
|
| |
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
|
|
|
|
| |
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
|
|
|
|
|
|
|
| |
The beagleboard doesn't boot with Thumb enabled, but without Thumb the
SPL (first stage bootloader) is too big to fit into SRAM.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
|
|
|
|
|
|
| |
to use them later by image/Makefile to create full working sdcard images
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
|
|
|
|
| |
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
|
|
|
|
|
|
|
|
|
|
| |
Use fixed led names and add each board variant instead of manipulating
the board name.
It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
| |
Update to version 2.02~rc2.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
|
|
|
|
|
|
| |
The HOSTCFLAGS override only works on newer u-boot versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
Cuts build time on Mac OS X in half by avoiding repeated $(shell) calls
from the build system
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
asm/* includes are not safe for the host build
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
Couple of important upstream patches (slated for 2.0.15) that
are necessary for kexec to run on MUSL and on x86 hardware.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
|
|
|
|
|
|
|
| |
With upstream changes, the last update to U-Boot 2017.03
broke the nsa310 and nsa325 targets. Also fix some redefines.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
|
|
|
|
|
|
| |
Use device tree based model string
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.
This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.
Note, this commit is just the initial board support hence the
following are not expected to work yet:
* WiFi
* Bluetooth
* 6lowpan
* Audio
* Mikrobus uarts, user leds (clock dependency of 6lowpan chip)
The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
Bump uboot-kirkwood to upstream release 2017.03
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
|
|
|
|
| |
Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>
|
|
|
|
| |
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
|
|
|
|
|
|
|
|
| |
Backport kernel patches for LS1043A Rev1.1 support from upstream,
patchwork, and SDK. And update to latest u-boot to support LS1043A
Rev1.1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
|
|
|
|
|
|
|
|
|
| |
This is needed for the definition of $(LINUX_DIR). This is used in
u-boot.mk to change the device-tree compiler to the dtc used by
linux.
Without this, the build will use the system dtc. This results in a
build failure when a dtc does not exist outside the buildroot.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specifying USE_PRIVATE_LIBGCC is no longer needed, as it is the
default.
Patch 001 is removed, since it was already merged upstream. Patches
100 and 101 are removed because they do not appear to be needed
anymore, and they do not conform with the sign-off and commit message
procedures.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Because they were hidden, there was no way to disable the uboot
targets in menuconfig, so they had to be built every time. The omap
target is the only one to hide uboot packages. To be consistent with
the other targets, and have more control over the build, un-hide the
u-boot packages.
Note that the default behavior remains unchanged, as uboot will be
built unless explicitly disabled.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
|
|
|
|
|
|
|
| |
fixes issue "nsa 310b u-boot can initialize usb but cannot
use usb storage so it cannot load files from usb"
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
|
|
|
|
| |
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
|
|
|
|
| |
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
|
|
|
|
| |
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
|
|
|
|
|
|
| |
add uboot for NSA325
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
|
|
|
|
|
|
| |
adding nsa325 envs for consistency with other kirkwoods
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
|
|
|
|
|
|
|
|
|
|
| |
Goflexhome/net use uImage, and to boot an uImage the u-boot
must use bootm command, not bootz.
Fixes the "i cannot boot LEDE with this u-boot" issue that I
found out myself with my goflexnet.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
|
|
|
|
|
|
|
|
|
|
| |
all patches for CONFIG_SYS_GENERIC_BOARD are obsolete for
uboot 2016 sources.
Run-tested with the uboot of goflexnet, also the md5sum of
all other uboots is the same with or without these patches.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Do not put the apex images into the kernel build directory as this directory
might get removed after kernel updates while the apex packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing u-boot images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
All SPL variants are lzo compressed. The lzop binary is used for
compression but is not available in tools.
Additionally at least the NAND SPL support is broken and doesn't create
working bootloaders.
The fb3370 SPI NOR SPL enabled u-boot isn't required for LEDE since the
LEDE images are targeting the pre-installed EVA bootloader.
Mark these u-boot variants as well as the SPL variants for the
reference boards as broken till the lzma issues are fixed upstream and
we can use lzma instead of lzo compression.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
| |
Use the standard off_t type instead of loff_t
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
stage u-boot images in KERNEL_BUILD_DIR for building images
always select uboot-mxs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|