aboutsummaryrefslogtreecommitdiffstats
path: root/package/boot
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for Netgear WNDR3700v4Paul Blazejowski2019-11-141-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNDR3700v4. Router was previously supported by ar71xx target only. Note: device requires 'ar934x-nand' driver in kernel. Specification ============= * Description: Netgear WNDR3700v4 * Loader: U-boot * SOC: Atheros AR9344 (560 MHz) * RAM: 128 MiB * Flash: 128 MiB (NAND) - U-boot binary: 256 KiB - U-boot environment: 256 KiB - ART: 256 KiB - POT: 512 KiB - Language: 2 MiB - Config: 512 KiB - Traffic Meter: 3 MiB - Firmware: 25 MiB - ART Backup: 256 KiB - Reserved: 96 MiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (amber/green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 2.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Note about partitioning: firmware partition offset (0x6c0000) is hardcoded into vendor's u-boot, so this partition cannot be moved and resized to include Netgear-specific flash areas (pot, language, config, traffic_meter) not used by OpenWrt. Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr3700-v4=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net>
* ath79: GL-AR750S: provide NAND support; increase kernel to 4 MBJeff Kletsky2019-11-141-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet GL-AR750S has been supported by the ar71xx and ath79 platforms with access to its 16 MB NOR flash, but not its 128 MB SPI NAND flash. This commit provides support for the NAND through the upstream SPI-NAND framework. At this time, the OEM U-Boot appears to only support loading the kernel from NOR. This configuration is preserved as this time, with the glinet,gl-ar750s-nand name reserved for a potential, future, NAND-only boot. The family of GL-AR750S devices on the ath79 platform now includes: * glinet,gl-ar750m-nor-nand "nand" target * glinet,gl-ar750m-nor "nand" target (NAND-aware) NB: This commit increases the kernel size from 2 MB to 4 MB "Force-less" sysupgrade is presently supported from the current versions of following NOR-based firmwre images to the version of glinet,gl-ar750s-nor firmware produced by this commit: * glinet,gl-ar750s -- OpenWrt 19.07 ar71xx * glinet,gl-ar750s -- OpenWrt 19.07 ath79 Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the NAND-based variant. Other upgrades to these images, including directly to the NAND-based glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot. NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which enables flashing of NAND factory.img with the current GL-iNet U-Boot, "U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)" The GL-AR750S OEM U-Boot allows upload and flashing of either NOR firmware (sysupgrade.bin) or NAND firmware (factory.img) through its HTTP-based GUI. Serial connectivity is not required. The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images generated after this commit flash each other directly. This commit changes the control of the USB VBUS to gpio-hog from regulator-fixed introduced by commit 0f6b944c92. This reduces the compressed kernel size by ~14 kB, with no apparent loss of functionality. No other ath79-nand boards are using regulator-fixed at this time. Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC and the GL.iNet source indicates that only the 0x0 offset is valid The ar71xx targets are unmodified. Cc: Alexander Wördekemper <alexwoerde@web.de> Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: add GL.iNet GL-AR300M16 as NOR-only boardJeff Kletsky2019-11-141-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet GL-AR300M series of devices includes variants without NAND and only the 16 MB NOR flash. These include the GL-AR300M16 and the GL-AR300M-Lite (already with its own board name). This board-name addition provides disambiguation from the NAND-bearing GL-AR300M devices, both for OpenWrt code and for end users. Kernel and firmware support for NAND and UBI will add ~320 kB to the overall firmware size at this time. This NOR-only option continues to provide more compact firmware for both the GL-AR300M16 as well as those who wish to use it as an alternate or primary, NOR-resident firmware on the GL-AR300M. The ar71xx targets are unmodified. Installation ------------ Install through OEM U-Boot (HTTP-based) or `sysupgrade --force` when booted from NOR and running OEM or OpenWrt, NOR-based firmware. As one of the intentions is disambiguation from NAND-bearing units, users who have flashed this firmware onto a device with NAND would need to use U-Boot or `sysupgrade --force` to flash firmware that again supports NAND. There are no additional SUPPORTED_DEVICES as it is not possible to determine if a device does or does not have NAND based on either the OEM's or OpenWrt's board names prior to this patch. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* uboot-envtools: ramips: add support for ALFA Network Quad-E4GPiotr Dymacz2019-11-141-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: ramips: add support for ALFA Network R36M-E4GPiotr Dymacz2019-11-131-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: Add TARGET_LDFLAGS to fix PIE and RELROHauke Mehrtens2019-11-092-11/+9
| | | | | | | | | Forward the OpenWrt TARGET_LDFLAGS to the linker of the fw_printenv tool. In addition also use the more standard make invocation script. With this change the fw_printenv tool is built with PIE and Full RELRO support when activated globally in OpenWrt. Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
* uboot-mxs: bump to v2019.10Michael Heimpold2019-11-092-9/+11
| | | | | | | | Also update the U-Boot BSP patch for I2SE Duckbill devices. Run tested on I2SE Duckbill and Olimex OLinuXino Maxi boards. Signed-off-by: Michael Heimpold <mhei@heimpold.de>
* ar71xx: update uboot-envtools for Netgear WNR routersMichal Cieslakiewicz2019-11-081-1/+10
| | | | | | | Boards added: WNR1000v2, WNR2000v3, WNR2200, WNR612v2, WNDR4300. Boards changed: WNDR3700 (u-boot env size is 2 sectors not 1). Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: update uboot-envtools for Netgear WNR routersMichal Cieslakiewicz2019-11-081-0/+6
| | | | | | Boards added: WNR1000v2, WNR2000v3, WNR612v2, WNDR3700. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNDR4300Michal Cieslakiewicz2019-11-021-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNDR4300. Router was previously supported by ar71xx target only. Note: device requires 'ar934x-nand' driver in kernel. Specification ============= * Description: Netgear WNDR4300 * Loader: U-boot * SOC: Atheros AR9344 (560 MHz) * RAM: 128 MiB * Flash: 128 MiB (NAND) - U-boot binary: 256 KiB - U-boot environment: 256 KiB - ART: 256 KiB - POT: 512 KiB - Language: 2 MiB - Config: 512 KiB - Traffic Meter: 3 MiB - Firmware: 25 MiB - ART Backup: 256 KiB - Reserved: 96 MiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (amber/green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 2.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Note about partitioning: firmware partition offset (0x6c0000) is hardcoded into vendor's u-boot, so this partition cannot be moved and resized to include Netgear-specific flash areas (pot, language, config, traffic_meter) not used by OpenWrt. Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* uboot-mvebu: add support for Macronix mx25u12835f flashVladimir Vid2019-11-011-0/+10
| | | | | | Some of A3700 boards use mx25u12835f, specifically uDPU and ESPRESSObin v7. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* ath79: add support for Netgear WNR2200Michal Cieslakiewicz2019-11-011-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNR2200. Router was previously supported by ar71xx target only (8 MiB variant). Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and 16 MiB for Russia and China markets. Apart from flash size both variants share the same hardware specification. Specification ============= * Description: Netgear WNR2200 * Loader: U-boot * SOC: Atheros AR7241 (360 MHz) * RAM: 64 MiB * Flash: 8 MiB or 16 MiB (SPI NOR) - U-boot binary: 256 KiB - U-boot environment: 64 KiB - Firmware: 7808 KiB or 16000 KiB - ART: 64 KiB * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN * Wireless: 2.4 GHz b/g/n (Atheros AR9287) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN (blue) - 4 x LAN (amber/green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1.5A * MAC addresses: LAN on case label, WAN +1, WLAN +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_generic=y CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y CONFIG_KERNEL_DEBUG_INFO=y CONFIG_KERNEL_DEBUG_KERNEL=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: uboot-envtools: Add GL-AR300M-LiteJeff Kletsky2019-10-241-0/+1
| | | | | | Add the GL.iNet GL-AR300M-Lite to the list of supported boards. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ipq40xx: add support for AVM FRITZ!Repeater 1200David Bauer2019-10-231-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Qualcomm IPQ4019 RAM: 256M DDR3 FLASH: 128M NAND WiFi: 2T2R IPQ4019 bgn 2T2R IPQ4019 a/n/ac ETH: Atheros AR8033 RGMII PHY BTN: 1x Connect (WPS) LED: Power (green/red/yellow) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz1200' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ1200.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz1200.bin uboot0 > mtd write /path/to/uboot-fritz1200.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-fritz4040: update to latest HEADDavid Bauer2019-10-231-3/+3
| | | | | | | | f92be9d add support for AVM FRITZ!Repeater 1200 d651302 enable support for Atheros AR8033 PHY e4c857c add machtype override hack Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-envtools: remove erasesize from MMC configTim Harvey2019-10-211-2/+2
| | | | | | | Erasesize doesn't belong in the u-boot env config for block devices as it is known to be 512 byte aligned. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* uboot-oxnas: remove unnecessary execute permission bitSungbo Eo2019-10-121-0/+0
| | | | | | .c files do not need to be executable. 644 is enough. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* grub2: fix a build regression on non-linux systemsFelix Fietkau2019-10-021-0/+31
| | | | | | Merge an upstream commit to correct a missing rename in generic code Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uboot-fritz4040: update to 2019-09-07David Bauer2019-09-251-3/+3
| | | | | | | | | | | | | 572ff7f fritzcreator: actually add checksum spacer 6edce1a fritzcreator: replace obscure padding generation with something more portable 2ff189f add ASUS RT-AC58U "easy install" factory u-boot shim b91f9c2 readd spi-nand support 486ae53 improve cmd_sysupgrade b0933f1 replace sstrip with strip 882e48a do not include generated files into git 0c5aa5f fix bugs in ipq40xx_cdp.c Signed-off-by: David Bauer <mail@david-bauer.net>
* sunxi: Add support for Banana Pi M2 UltraHal Martin2019-09-212-0/+32
| | | | | | | | | | | | | | | | | | CPU: Allwinner R40 Quad-Core Cortex-A7 @ 1.2GHz GPU: Mali 400 MP2 Memory: 2GB DDR3 onboard (shared with GPU) Onboard: Storage microSD card slot Onboard: Storage 8GB eMMC Onboard: Network 10/100/1000M Ethernet RJ45 Onboard: Network WiFi 802.11b/g/n 1x1 (AMPAK AP6212; brcmfmac) Onboard header: SPI, I2C, GPIO, UART USB: Two USB 2.0 Host, One USB 2.0 OTG Known issues: - WiFi doesn't work - eMMC not supported Signed-off-by: Hal Martin <hal.martin@gmail.com>
* uboot-fritz4040: build with ipq40xx "generic" subtargetYousong Zhou2019-09-061-0/+1
| | | | | | Fixes: 853e4dd3 ("ipqx0xx: add Generic subtarget") Ref: https://forum.openwrt.org/t/ipq40xx-snapshot-not-updated-since-22nd-august/44126 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* uboot-envtools: Update to U-Boot version 2019.07Hauke Mehrtens2019-09-042-7/+7
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* grub2: bump to 2.04Tomasz Maciej Nowak2019-09-017-187/+11
| | | | | | | | | | | | | | | | | | | | | * GCC 8 and 9 support. * Gnulib integration overhaul. * RISC-V support. * Xen PVH support. * Native UEFI secure boot support. * UEFI TPM driver. * New IEEE 1275 obdisk driver. * Btrfs RAID 5 and RIAD 6 support. * bootin from F2FS support. * PARTUUID support. * VLAN support. * Native DHCP support. * Many ARM and ARM64 fixes. * Many SPARC fixes. * Many IEEE 1275 fixes. * ...and tons of other fixes and cleanups... Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* uboot-zynq: update to 2019.07Luis Araneda2019-09-015-569/+28
| | | | Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* mvebu: uDPU: add sysupgrade supportVladimir Vid2019-08-241-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds sysupgrade, uboot-env and networking support for Methode uDPU device. Device features 4 partitions: ----------------------------------------- | boot | recovery | rootfs | misc | | (ext4) | (ext4) | (fsf2) | (f2fs) | _________________________________________ Idea was to use f2fs only but the u-boot currently lacks support so first 2 partition are ext4 to be u-boot readable, and this was a reason why custom build and sysupgrade sections were required. On the sysupgrade, boot and rootfs partitions are updated, firmare image and user configuration is saved on the misc partition and if the upgrade was successfull, recovery partition will be updated on after the reboot from preinit script. If the sysupgrade fails for any reason, device will fallback to recovery initramfs image. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* at91bootstrap: add sama5d27_som1_eksd1_uboot as default defconfigSandeep Sheriker M2019-08-171-3/+3
| | | | Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* at91bootstrap: add support for at91sam9x5ekSandeep Sheriker M2019-08-171-0/+14
| | | | Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* at91bootstrap: bump v3.8.10 to v3.8.12Sandeep Sheriker M2019-08-171-3/+2
| | | | Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* uboot-at91: fix -Wformat-securitySandeep Sheriker M2019-08-172-1/+14
| | | | | | add patch to fix -Wformat-security warnings. Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* uboot-at91: changed som1 ek default defconfigsSandeep Sheriker M2019-08-171-5/+5
| | | | | | | replaced som1 ek spi flash with qspi defconfig and mmc with mmc1 defconfig. Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* uboot-at91: add at91sam9x5ek socSandeep Sheriker M2019-08-171-0/+9
| | | | | | add support to build u-boot binaries for at91sam9x5ek socs. Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* uboot-at91: bump linux4sam_5.8 to linux4sam_6.0Sandeep Sheriker M2019-08-171-2/+2
| | | | Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* build: include BUILD_VARIANT in PKG_BUILD_DIRJeffery To2019-08-051-1/+0
| | | | | | | | | | | This changes the default PKG_BUILD_DIR to take BUILD_VARIANT into account (if set), so that packages do not need to manually override PKG_BUILD_DIR just to handle variants. This also updates most base packages with variants to use the updated default PKG_BUILD_DIR. Signed-off-by: Jeffery To <jeffery.to@gmail.com>
* uboot-envtools: ath79: add support for ALFA Network AP121FPiotr Dymacz2019-07-311-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: ath79: fix indent and alphabetical orderPiotr Dymacz2019-07-311-3/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* tfa-layerscape: fix create_pbl and byte_swap host buildBiwen Li2019-07-263-2/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - make create_pbl and byte_swap as host tools - fix a bug that maybe use the cross compiler to compile create_pbl and byte_swap: # -a option appends the image for Chassis 3 devices in case of non secure boot aarch64-openwrt-linux-musl-gcc -Wall -Werror -pedantic -std=c99 -O2 -DVERSION=v1.5(release):reboot-10604-ge9216b3336 -D_GNU_SOURCE -D_XOPEN_SOURCE=700 -c -o create_pbl.o create_pbl.c cc1: note: someone does not honour COPTS correctly, passed 0 times LD create_pbl /usr/bin/ld: create_pbl.o: Relocations in generic ELF (EM: 183) /usr/bin/ld: create_pbl.o: Relocations in generic ELF (EM: 183) /usr/bin/ld: create_pbl.o: Relocations in generic ELF (EM: 183) create_pbl.o: error adding symbols: File in wrong format collect2: error: ld returned 1 exit status Makefile:43: recipe for target create_pbl failed make[4]: *** [create_pbl] Error 1 plat/nxp/tools/pbl_ch2.mk:45: recipe for target pbl failed make[3]: *** [pbl] Error 2 - add tfa- prefix to all tools in order to avoid future clashes with other toolnames Signed-off-by: Biwen Li <biwen.li@nxp.com> [added missing HOST_CFLAGS, added tfa- prefix to the tools] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* tfa-layerscape: fix fiptool host buildPetr Štetiar2019-07-252-2/+88
| | | | | | | | | | | | | | | | | | fiptool is a host tool, used in a firmware generation pipeline, but it's not treated as such, leading to the build breakage on the hosts which don't have {Open,Libre}SSL dev package installed: In file included from fiptool.h:16:0, from fiptool.c:19: fiptool_platform.h:18:27: fatal error: openssl/sha.h: No such file or directory # include <openssl/sha.h> So this patch promotes fiptool into the host tool with proper host include and library paths under STAGING_DIR. Ref: https://github.com/openwrt/openwrt/pull/2267 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for Qihoo C301Chuanhong Guo2019-07-161-0/+3
| | | | | | | | | | | | | | | | Specifications: - SoC: AR9344 - RAM: 128MB - Flash: 2 * 16MB (MX25L12845) - Ethernet: 2 * FE LAN & 1 * FE WAN - WiFi: 2.4G: AR9344 5G: QCA9882 Flash instruction: 1. Hold reset and power up the router 2. Set your IP to 192.168.1.x 3. Open 192.168.1.1 and upload the generated *factory* firmware Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* uboot-envtools: Apply ramips device renamesAdrian Schmutzler2019-07-101-9/+9
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* u-boot-mvebu: bump to 2019.04Vladimir Vid2019-06-281-2/+2
| | | | | | | | | Some devices and packages require newer version of u-boot to work properly, update u-boot to keep up with 4.19 kernel. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr> [re-added missing commit message] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kexec-tools: change kdump.init STOP indexJoseph Tingiris2019-06-242-2/+2
| | | | | | | | | This patch is in a series to allow additional STOP indexes after umount, so that other block devices may stop cleanly. kdumpinit is now STOP=90 Signed-off-by: Joseph Tingiris <joseph.tingiris@gmail.com>
* treewide: fix syntax errors exposed after kconfig updateJo-Philipp Wich2019-06-201-2/+2
| | | | | | | | | | | | | | After commit e82a4d9cfb ("config: regenerate *_shipped sources") the mconf parser became more strict as a side effect and started to spew a series of warnings when evaluating our generated kconfig sources: tmp/.config-package.in:705:warning: ignoring unsupported character '@' The root cause of these warnings is a wrong use of the @SYMBOL dependency syntax in various Makefile. Fix the corresponding Makefiles by turning `@SYM||@SYM2` expressions into the proper `@(SYM||SYM2)` form. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* mvebu: fix regression for non-generic ESPRESSObin versionsVladimir Vid2019-06-181-0/+3
| | | | | | | | | | | | | When targets for multiple ESPRESSObin devices were added, not all files were updated which means any ESPRESSObin version beside generic won't have proper networking, sysupgrade and uboot-env. This patch fixes the issue. * fixup network detection * fixup uboot-env * fixup platform.sh for sysupgrade Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* layerscape: fix u-boot bootcmdBiwen Li2019-06-063-0/+84
| | | | | | | | | | | Current latest LSDK-19.03 u-boot had a bug that bootcmd environment was always been reset when u-boot started up. This was found on boards with spi NOR boot. Before the proper fix-up is applied, we have to use a workaround to hard code the bootcmd for OpenWrt booting for now. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: convert to use TF-A for firmwareBiwen Li2019-06-066-17/+17
| | | | | | | | | | This patch is to convert to use TF-A for firmware. - Use un-swapped rcw since swapping will be done in TF-A. - Use u-boot with TF-A defconfig. - Rework memory map for TF-A introduction. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add ARM Trusted Firmware packageBiwen Li2019-06-061-0/+140
| | | | | | | Add TF-A packages for Layerscape to implement trusted firmware. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: drop armv8_32b supportYangbo Lu2019-06-061-84/+0
| | | | | | | NXP LSDK has decided to drop armv8_32b support considering few users are using it. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update u-boot to LSDK 19.03Biwen Li2019-06-061-3/+3
| | | | | | | Update u-boot to LSDK 19.03. Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* at91:renaming subtraget legacy to sam9xSandeep Sheriker M2019-05-301-2/+2
| | | | | | renaming subtraget legacy to sam9x for adding new sam9 soc's Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* at91: Merge SAMA5 subtargetsHauke Mehrtens2019-05-302-24/+24
| | | | | | | | | Instead of maintaining 3 very similar subtargets merge them into one. This does not use the Arm NEON extension any more, because the SAMA5D3 does not support NEON. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-15 19:14:43 +0000