aboutsummaryrefslogtreecommitdiffstats
path: root/package/boot/uboot-kirkwood/Makefile
Commit message (Collapse)AuthorAgeFilesLines
* kirkwood: Add support for SheevaplugBERENYI Balazs2021-06-061-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Globalscale SheevaPlug: * Marvell Kirkwood 88F6281 * 512 MB SDRAM * 512 MB Flash * Gigabit Network * USB 2.0 * SD slot * Serial console The device is supported in mainline uboot/linux the commit adds only some openwrt config for building an image. Installation: 1 - Update uboot: setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot u-boot.kwb nand erase 0x0 0x100000 nand write 0x800000 0x0 0x100000 reset 2 - Install OpenWRT: setenv ethaddr 00:50:43:01:xx:xx saveenv setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot openwrt-kirkwood-globalscale_sheevaplug-squashfs-factory.bin nand erase.part ubi nand write 0x800000 ubi 0x600000 reset Signed-off-by: BERENYI Balazs <balazs@wee.hu> Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com> [add vendor name for uboot-kirkwood, merge patches, copy to 5.10, add AUTORELEASE for uboot-kirkwood, refresh patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: add support for Seagate BlackArmor NAS220Kip Porterfield2020-12-221-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Seagate BlackArmor NAS220 is a consumer NAS with two internal drive bays. The stock OS runs RAID 1 over the disks via mdadm. Device specification: - SoC: Marvell 88F6192 800 MHz - RAM: 128 MB - Flash: 32 MB - 2 x internal SATA II drives - Ethernet: 10/100/1000 Mbps (single port, no switch) - WLAN: None - LED: Power, Status, Sata Activity - Key: Power, Reset - Serial: 10 pin header, (115200,8,N,1), 3.3V TTL 9|x - x|10 7|x - x|8 5|x - GND|6 3|x - RX|4 1|TX - x|2 front of case - USB ports: 2 x USB 2.0 Flash instruction: NOTE: this process uses a serial connection. It will upgrade the bootloader and reset the bootloader environment variables TFTP server setup - Setup PC with TFTP server set the PC IP to 10.4.50.5 as TFTP server - Copy these files to TFTP server location - u-boot.kwb - seagate_blackarmor-nas220-initramfs-uImage - seagate_blackarmor-nas220-squashfs-sysupgrade.bin - seagate_blackarmor-nas220-squashfs-factory.bin Seagate NAS setup - Connect LAN cable between PC and seagate device - Connect to serial to seagate device Install u-boot - Boot seagate device and stop in bootloader by pressing any key - run 'printenv' from u-boot and save the values - tftpboot 0x2000000 u-boot.kwb - nand erase.part uboot - nand write 0x2000000 0x0 ${filesize} - reset Update MAC address in u-boot env - Stop in u-boot by pressing any key - Get your MAC address from your saved printenv. Is also on chassis - setenv ethaddr <your MAC> - saveenv Option 1 (recommended) - Install OpenWrt via initramfs and sysupgrade - tftpboot 0x2000000 seagate_blackarmor-nas220-initramfs-uImage - bootm 0x2000000 - *OpenWrt should be running now, however it is not written to flash yet* - From the running instance of OpenWrt use Luci's "flash image" feature from the web site or use sysupgrade from the console to write seagate_blackarmor-nas220-squashfs-sysupgrade.bin to flash Option 2 - Install OpenWrt by flashing factory image from u-boot - nand erase.part ubi - tftpboot 0x2000000 seagate_blackarmor-nas220-squashfs-factory.bin - nand write 0x2000000 ubi ${filesize} - reset Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
* uboot-kirkwood: add uboot for CheckPoint L-50Pawel Dembicki2020-07-111-0/+6
| | | | | | This patch add u-boot for CheckPoint L-50 routers. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* uboot-kirkwood: add support for Zyxel NSA310SPawel Dembicki2020-07-081-0/+6
| | | | | | | This patch modifies the u-boot config for the Zyxel NSA310S to work with OpenWrt. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* uboot-kirkwood: update to 2020.04Pawel Dembicki2020-04-201-2/+2
| | | | | | | | | | | | | Update U-Boot to current 2020.04 release for kirkwood platform. Catch up with upstream and move some configuration options from the header files to the corresponding defconfig files. Compile tested: all devices Run tested: nsa310, pogoplugv4 Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [nsa310] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* uboot-kirkwood: update to 2019.01Paul Wassi2019-02-171-2/+2
| | | | | | Update U-Boot to current 2019.01 release for kirkwood platform Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* uboot-kirkwood: update to 2018.03Paul Wassi2018-03-201-2/+2
| | | | | | | | | | | U-Boot now requires GCC > 5 Catch up with upstream and move some configuration options from the header files to the corresponding defconfig files. Also move some options of patch 010 affecting the whole platform to 010's device only. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* uboot-kirkwood: add uboot for pogoplug v4Alberto Bursi2018-01-091-1/+7
| | | | | | | | | | | | | | | | | | | | | add an uboot able to boot a kernel in an ubi partition This uboot also has a "recovery" feature, before booting from flash it will try to boot a initramfs image called "initramfs.bin" from a FAT32-formatted USB drive connected to the USB 2.0 port. (u-boot lacks drivers for usb 3.0 controllers) Just rename the initramfs image and place it on the usb drive, the uboot will load it. In case there is no USB drive or no such file is found, the uboot will boot from internal flash. The whole check takes less than a second, boot times are not impacted. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: sync image filename with boardnameMathias Kresin2018-01-091-3/+11
| | | | | | | | | | Use <manufacturer>_<modelname> as image name. Use the BOARD_NAME variable to ensure that the former used boardname is still used as the subdirectory name for the sysupgrade-tar image, to not break sysupgrade from earlier versions. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uboot-kirkwood: fix default u-boot selectionMathias Kresin2018-01-091-0/+2
| | | | | | | | | Build the Seagate GoFlexHome u-boot for the Seagate GoFlexNet as well. The name clearly indicates that the u-boot can be used for both boards Build the Zyxel NSA310 u-boot if the NSA310B image is selected. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: drop support for orphaned boardsMathias Kresin2018-01-091-6/+1
| | | | | | | No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop support for the boards for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uboot-kirkwood: update to 2017.09Paul Wassi2017-11-031-2/+2
| | | | | | | | | | Upgrade uboot-kirkwood to upstream release 2017.09 Catch up with upstream and move configuration options from simple defines to Kconfig, as otherwise dependencies would not be resolved and code would not compile. Tested-by: Alberto Bursi <alberto.bursi@outlook.it> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* package/boot: update uboot-kirkwood to 2017.03Paul Wassi2017-03-201-2/+2
| | | | | | Bump uboot-kirkwood to upstream release 2017.03 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* uboot-kirkwood: add Zyxel NSA325 ubootAlberto Bursi2017-02-111-0/+5
| | | | | | add uboot for NSA325 Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* uboot-kirkwood: switch to u-boot.mkFelix Fietkau2017-01-241-78/+38
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uboot-kirkwood: add uboot for nsa310bAlberto Bursi2017-01-241-0/+5
| | | | | | | | | | | | this commit allows to make a standalone u-boot for nsa310b. While both first-stage and second-stage u-boot work fine if installed to flash or loaded with kwboot, I could not get stock u-boot nor bodhi's u-boot to chainload any second stage u-boot (I also tried with dockstar's uboot that works fine on this device if loaded with kwboot). Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* treewide: clean up download hashesFelix Fietkau2016-12-161-1/+1
| | | | | | Replace *MD5SUM with *HASH, replace MD5 hashes with SHA256 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uboot-kirkwood: bump to upstream 2016.09.01Paul Wassi2016-10-271-2/+2
| | | | | | | Bump U-Boot for Kirkwood to upstream 2016.09.01. Local patches cleaned up and reworked. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* uboot-kirkwood: bump to 2014.10Luka Perkov2014-11-301-12/+10
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 43436
* uboot-*: update license info in uboot packagesLuka Perkov2014-11-291-0/+3
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 43429
* license info - revert r43155John Crispin2014-11-031-3/+0
| | | | | | | | turns out that r43155 adds duplicate info. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 43167
* Add more license tags with SPDX identifiersJohn Crispin2014-11-031-0/+3
| | | | | | | | | | | | | | | | | | Note, that licensing stuff is a nightmare: many packages does not clearly state their licenses, and often multiple source files are simply copied together - each with different licensing information in the file headers. I tried hard to ensure, that the license information extracted into the OpenWRT's makefiles fit the "spirit" of the packages, e.g. such small packages which come without a dedicated source archive "inherites" the OpenWRT's own license in my opinion. However, I can not garantee that I always picked the correct information and/or did not miss license information. Signed-off-by: Michael Heimpold <mhei@heimpold.de> SVN-Revision: 43155
* uboot-kirkwood: bump to 2014.07Luka Perkov2014-08-081-2/+2
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 42080
* uboot-kirkwood: re-add Pogoplug E02 supportLuka Perkov2014-05-231-1/+5
| | | | | | | | | This patch modifies the u-boot config for the Pogoplug E02 to work with OpenWrt. It also enables building a second stage bootloader image. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> SVN-Revision: 40828
* uboot-kirkwood: update to 2014.04Luka Perkov2014-05-201-3/+3
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 40804
* uboot-kirkwood: add support for Seagate GoFlexNetLuka Perkov2014-02-161-0/+5
| | | | | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 39594
* uboot-kirkwood: update to 2013.10Luka Perkov2014-02-151-13/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tested on: * Cloud Engines Pogoplug E02 * RaidSonic ICY BOX IB-NAS62x0 * Iomega Iconnect Some users are avoiding to replace their bootloader, because of that add support for second stage u-boot image. Having ubifs capable bootloader is required in order to boot current OpenWrt trunk. Sample ib62x0 commands for running second stage bootloader: tftpboot 0x800000 uboot-kirkwood-ib62x0_second_stage/openwrt-kirkwood-ib62x0_second_stage-u-boot.img bootm 0x800000 Sample ib62x0 commands for flashing second stage bootloader: tftpboot 0x800000 uboot-kirkwood-ib62x0_second_stage/openwrt-kirkwood-ib62x0_second_stage-u-boot.img nand erase 0x100000 0x100000 ; nand write 0x800000 0x100000 0x${filesize} nand read 0x800000 0x100000 0x100000 ; bootm 0x800000 While at it include parallel build support, use alphabetic order of the boards and introduce common OpenWrt configuration. Signed-off-by: Luka Perkov <luka@openwrt.org> Tested-by (on ib62x0): Luka Perkov <luka@openwrt.org> Tested-by (on dockstar): Alexander Couzens <lynxis@fe80.eu> Tested-by (on iconnect): Wojciech Dubowik <wojciech.dubowik@neratec.com> CC: Felix Kaechele <heffer@fedoraproject.org> CC: Wojciech Dubowik <wojciech.dubowik@neratec.com> CC: Alexander Couzens <lynxis@fe80.eu> CC: Daniel Engberg <daniel.engberg@pyret.net> CC: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 39590
* u-boot: prefer mirror2.openwrt.org over ftp.denx.de - the denx ftp is slow ↵Felix Fietkau2013-10-281-1/+3
| | | | | | | | and unreliable Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 38559
* uboot-kirkwood: build in $(BUILD_DIR)Luka Perkov2012-11-291-2/+1
| | | | SVN-Revision: 34401
* uboot-kirkwood: update to 2012.10Luka Perkov2012-11-221-10/+5
| | | | SVN-Revision: 34303
* move boot related packages to their own folderJohn Crispin2012-10-161-0/+110
SVN-Revision: 33781
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-31 07:11:59 +0000