aboutsummaryrefslogtreecommitdiffstats
path: root/package/boot/uboot-envtools
Commit message (Collapse)AuthorAgeFilesLines
* uboot-envtools: Change download to git.Rosen Penev2018-05-021-6/+7
| | | | | | | | Currently, the build system uses an openwrt mirror which does not currently work and FTP can be unreliable under several circumstances. This change implicitly allows using all the mirrors to download. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* uboot-envtools: add support for ESPRESSObin and MACCHIATObinDamir Samardzic2018-04-251-0/+4
| | | | | | | | Added for convenience. These boards can be used as dev boards running various operating systems from different media, and this simplifies work with U-Boot environment. Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* ipq40xx: add support for OpenMesh A62Sven Eckelmann2018-04-231-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + 802.3at POE+ - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 18-24V passive POE (mode B) * powered only via POE The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. The initramfs image can be started using setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)' tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb set fdt_high 0x85000000 bootm 0x84000000 Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* uboot-envtools: remove makefile duplication for supported targetsFelix Fietkau2018-04-201-47/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uboot-envtools: update to 2018.03Luis Araneda2018-04-186-234/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several changes has been made: + AES support has been removed by upstream commit c6831c7 (2017-11-14) [remove patch "200-fw_env_no_aes.patch"] + Support for UBI volumes has beed added by upstream commit 34255b9 (2017-11-15) [remove patch "300-support-env-in-ubivol-chardev.patch"] + A command line argument has beed added ("-c") to manually indicate the location of the environment configuration file Also, patch "400-u-boot-2015.10-stdint.patch" is no longer necessary, and the config option to enable UBI support has been removed. Size comparisons: fw_printenv size: Target Before After ar71xx 15,189 bytes 18,133 bytes (+2,944 bytes) ipq40xx 20,873 bytes 20,987 bytes (+114 bytes) mvebu 20,881 bytes 20,991 bytes (+110 bytes) ramips 15,128 bytes 18,072 bytes (+2,944 bytes) OPKG package size: Target Before After ar71xx 11,309 bytes 12,875 bytes (+1,566 bytes) ipq40xx 11,772 bytes 13,299 bytes (+1,527 bytes) mvebu 11,609 bytes 13,114 bytes (+1,505 bytes) ramips 10,975 bytes 12,503 bytes (+1,528 bytes) Compile tested: ipq40xx (musl, glibc, gcc5-musl), ar71xx, mvebu, ramips Run tested: ipq40xx (ASUS RT-AC58U) Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ramips: add U-Boot env support for ALFA Network AC1200RMPiotr Dymacz2018-04-061-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: fix ALFA Network AWUSFREE1 supportPiotr Dymacz2018-04-061-7/+9
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: add targetJohn Crispin2018-03-143-4/+47
| | | | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
* mvebu: add support for Turris OmniaRyan Mounce2018-03-101-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Turris Omnia and builds an eMMC sysupgrade image in the same format as the SolidRun ClearFog. An initramfs image in the simple yet Omnia-specific 'medkit' image format is also built in order to ease the initial flashing process. Notable hardware support omissions are support for switching between SFP cage and copper PHY, and RGB LED control. Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used. Specifications: - Marvell Armada 385 1.6GHz dual-core ARMv7 CPU - 1GB DDR3 RAM - 8GB eMMC Flash - 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports) - 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN - 2x USB 3.0 - 12x dimmable RGB LEDs controlled by independent MCU - 3x Mini PCIe slots - Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz) - Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz) - Optional Quectel EC20 Mini PCIe LTE modem Flash instructions: If the U-Boot environment has been modified previously (likely manually via serial console), first use serial to reset the default environment. => env default -a => saveenv Method 1 - USB 'medkit' image w/o serial - Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS. Note that the medkit MUST be named omnia-medkit*.tar.gz - Disconnect other USB devices from the Omnia and connect the flash drive to either USB port. - Power on the Omnia and hold down the rear reset button until 4 LEDs are illuminated, then release. - Wait approximately 2 minutes for the Turris Omnia to flash itself with the temporary image, during which LEDs will change multiple times. - Connect a computer to a LAN port of the Turris Omnia with a DHCP client - (if necessary) ssh-keygen -R 192.168.1.1 - ssh root@192.168.1.1 $ mount /dev/sda1 /mnt $ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself and you can remove the flash drive. Method 2 - TFTP w/ serial - Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy dtb + zImage to your TFTP server (rename if desired) - Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server - Connect serial console and interrupt U-Boot => dhcp => setenv serverip <tftp_server_ip_here> => tftpboot 0x01000000 zImage => tftpboot 0x02000000 dtb => bootz 0x01000000 - 0x02000000 - OpenWrt will now boot from ramdisk - Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/ $ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* uboot-envtools: add support for ALFA Network AWUSFREE1Piotr Dymacz2018-02-221-6/+7
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for YunCore T830Piotr Dymacz2018-02-221-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for Samsung WAM250Piotr Dymacz2018-02-221-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for WHQX E1700AC/E600G/E600GAC v2Piotr Dymacz2018-02-221-0/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: Add eTactica EG-200 supportKarl Palsson2018-02-131-0/+1
| | | | | | | | | | | | | | EG-200 is a DIN rail mountable device with one ethernet port, wifi, an RS-485 port, and an internal USB attached uSD card reader. Two leds, "modbus" and "etactica" are managed by userspace applications in factory firmware. Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Karl Palsson <karlp@etactica.com>
* uboot-envtools: add support for GL.iNet GL-AR750Piotr Dymacz2018-01-151-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for ALFA Network R36APiotr Dymacz2018-01-151-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for ALFA Network N5QPiotr Dymacz2018-01-141-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for ALFA Network AP91-5GPiotr Dymacz2018-01-141-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add OpenMesh A42 supportSven Eckelmann2018-01-131-0/+3
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ipq806x: Sort occurrences of boardame alphabeticallyLuis Araneda2018-01-131-3/+3
| | | | | | | This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: convert to dt-based board-detectionLuis Araneda2018-01-131-3/+4
| | | | | | | | | | | | | | | | | Use the generic board detection method: - Board name: First compatible string from the device tree - Board model: Model property from the device tree Change occurrences of board name in userspace by the compatible string, and removed target specific board detection script Replace the definition of SUPPORTED_DEVICES in Device/Default to extract the dt compatible string from each device definition. Additionally, for devices supported by lede-17.01, append the value of BOARD_NAME to SUPPORTED_DEVICES in the device definition. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* kirkwood: sort occurrences of boardame alphabeticallyMathias Kresin2018-01-091-5/+5
| | | | | | | This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uboot-envtools: add pogoplug v4Alberto Bursi2018-01-091-1/+2
| | | | | | add pogoplug v4 envs support in uboot-envtools Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: use the generic board detectMathias Kresin2018-01-091-7/+7
| | | | | | | Drop the target specific detection function in favour of the generic one provided by base-files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: drop support for orphaned boardsMathias Kresin2018-01-091-4/+1
| | | | | | | No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop support for the boards for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uboot-envtool: remove superfluous + sign from PKG_BUILD_DEPENDSMatthias Schiffer2018-01-071-1/+1
| | | | | | A + sign does not have meaning in build depends. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ramips: drop LinkIt Smart 7688 Duo userspace supportMathias Kresin2017-12-211-1/+0
| | | | | | | | | | The LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the extra ATmega32U4 - accessible via UART - on the the Duo. Since all relevant hardware is identical, drop the Duo special handling in userspace. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use the compatible string as board nameMathias Kresin2017-12-161-5/+5
| | | | | | | | | | | Use the first compatible string as board name in userspace. Add the new board name as well as the former used board name to the image metadata to keep compatibilty with already deployed installations. Don't add the former used boardname for boards which exists only in master or evaluation boards. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uboot-envtools: add support for Wallys DR342Piotr Dymacz2017-11-141-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: add support for Nokia WI2A-AC200iFelix Fietkau2017-10-191-0/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: improve Xiaomi Mi Router 3G supportKevin Darbyshire-Bryant2017-09-281-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit improves support for the Xiaomi Mi Router 3G originally added in commit 6e283cdc0da25928f8148805ebef7f8f2b769ee8 Improvements: - Remove software watchdog as hardware watchdog now working as per commit 3fbf3ab44f5cebb22e30a4c8681b13341feed6a6 for all mt7621 devices. - Reset button polarity corrected - length of press determines reboot (short press) vs. reset to defaults (long press) behaviour. - Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit link and blink on activity. Green LEDs driven directly by switch indicating any link speed and tx activity. - USB port power on/off GPIO exposed as 'usbpower' - Add access to uboot environment settings for checking/setting uboot boot order preference from user space. Changes: - Front LED indicator is physically made of independent Yellow/Amber, Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel indicator, hence the colour behaviour is similar to an RGB LED. RGB LEDs are not supported at this time because they produce colour results that do not then match colour labels, e.g. enabling 'mir3g:red' and 'mir3g:blue' would result in a purple indicator and we have no such label for purple. The yellow, red & blue LEDs have been split out as individual yellow, red & blue status LEDs, with yellow being the default status LED as before and with red's WAN and blue's USB default associations removed. - Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan layout. eth0.1 is LAN, eth0.2 is WAN - Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet leakage between kernel switch init and uci swconfig uboot behaviour & system 'recovery' uboot expects to find bootable kernels at nand addresses 0x200000 & 0x600000 known by uboot as "system 1" and "system 2" respectively. uboot chooses which system to hand control to based on 3 environment variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed last_success represents a preference for a particular system and is set to 0 for system 1, set to 1 for system 2. last_success is considered *if* and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either* failed flags are set then uboot will attempt to hand control to the non failed system. If both failed flags are set then uboot will check the uImage CRC of system 1 and hand control to it if ok. If the uImage CRC of system is not ok, uboot will hand control to system 2 irrespective of system 2's uImage CRC. NOTE: uboot only ever sets failed flags, it *never* clears them. uboot sets a system's failed flag if that system's was selected for boot but the uImage CRC is incorrect. Fortunately with serial console access, uboot provides the ability to boot an initramfs image transferred via tftp, similarly an image may be flashed to nand however it will flash to *both* kernels so a backup of stock kernel image is suggested. Note that the suggested install procedure below set's system 1's failed flag (stock) thus uboot ignores the last_success preference and boots LEDE located in system 2. Considerable thought has gone into whether LEDE should replace both kernels, only one (and which one) etc. LEDE kernels do not include a minimal rootfs and thus unlike the stock kernel cannot include a method of controlling uboot environment variables in the event of rootfs mount failure. Similarly uboot fails to provide an external mechanism for indicating boot system failure. Installation - from stock. Installation through telnet/ssh: - copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it from LEDE download site to /tmp - switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if wgetted from LEDE download site - run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1 - run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0 - run: nvram set flag_try_sys1_failed=1 - run: nvram commit - run: reboot Recovery - to stock. Assuming you used the above installation instructions you will have a stock kernel image in system 1. If it can be booted then it may be used to perform a stock firmware recovery, thus erasing LEDE completely. From a 'working' LEDE state (even failsafe) Failsafe only: - run: mount_root - run: sh /etc/uci-defaults/30_uboot-envtools Then do the steps for 'All' All: - run: fw_setenv flag_try_sys2_failed 1 - run: reboot The board will reboot into system 1 (stock basic kernel) and wait with system red light slowly blinking for a FAT formatted usb stick with a recovery image to be inserted. Press and hold the reset button for around 1 second. Status LED will turn yellow during recovery and blue when recovery complete. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* uboot-envtools: Add support for IPQ806x AP148 and DB149Ram Chandra Jangir2017-08-301-0/+21
| | | | | | | | | IPQ806x AP148 and DB149 boards didn't have the UCI ubootenv section initialized, so the usage of fw_printenv required manual configuration. With this change, the "fw_printenv" and "fw_setenv" command will automatically work on NOR and NAND based platforms. Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* ramips: drop Edimax BR-6425 supportMathias Kresin2017-08-031-1/+0
| | | | | | Code to build an image for the Edimax BR-6425 never existed. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uboot-envtools: add support for ALFA Network AP121FPiotr Dymacz2017-07-221-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* treewide: use the generic board_name functionMathias Kresin2017-07-159-18/+9
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* uboot-envtools: add Arduino Yun supportCamille Bilodeau2017-06-291-0/+1
| | | | Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
* ar71xx: add support for EnGenius ENS202EXTMarty Plummer2017-05-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius ENS202EXT is an outdoor wireless access point with 2-port 10/100 switch, detachable antennas and proprietery PoE. The device is based on Qualcomm/Atheros AR9341 v1. Specifications: - 535/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM - 16 MB of FLASH - UART (J1) header on PCB (unpopulated) - 2x 10/100 Mbps Ethernet - 2.4 GHz, up to 26dBm - 2x external, detachable antennas - 7x LED, 1x button Flash instructions: You have three options: - Use the vendor firmware upgrade page on the web interface and give it the factory.img. This is the easiest way to go about it. - If you have serial access during u-boot, interrupt the normal boot (any key before timeout) and run 'run failsafe_boot'; this will bring you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've bricked the normal firmware. - Use the vendor's management cli, which can be accessed via telnet with the same credentials as the web login (default admin:admin), then issue the following commands: *** Hi admin, welcome to use cli(V-1.6.7) *** ---========= Commands Help =========--- stat -- Status sys -- System wless2 -- 2.4G-Wireless mgmt -- Management tree -- Tree help -- Help reboot -- Reboot ens202ext>mgmt Management ---========= Commands Help =========--- admin -- Administration mvlan -- Management VLAN settings snmp -- SNMP settings backup -- Backup/Restore settings autorb -- Auto reboot settings fwgrade -- Firmware upgrade time -- Time settings wifisch -- Wifi schedule log -- Log diag -- Diagnostics disc -- Device Discovery logout -- Logout help -- Help exit -- Exit ens202ext/mgmt>fwgrade Management --> Firmware upgrade ---========= Commands Help =========--- fwup -- Firmware upgrade help -- Help exit -- Exit ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
* uboot-envtools: add support for 8devices RambutanMantas Pucka2017-05-151-0/+4
| | | | Signed-off-by: Mantas Pucka <mantas@8devices.com>
* ramips: dont replace the board nameMathias Kresin2017-04-211-1/+2
| | | | | | | | | | Use fixed led names and add each board variant instead of manipulating the board name. It makes the ramips board name function less different to the one used in other targets and allows to merge them with a common function. Signed-off-by: Mathias Kresin <dev@kresin.me>
* pistachio: remove custom board detection overrideFelix Fietkau2017-03-221-1/+1
| | | | | | Use device tree based model string Signed-off-by: Felix Fietkau <nbd@nbd.name>
* pistachio: remove pistachio_board_name, use the generic functionFelix Fietkau2017-03-221-2/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* target: add pistachioIan Pozella2017-03-222-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Pistachio target is a MIPS interaptiv based SoC developed by Imagination Technologies. It includes blocks for i2c, spi, audio, usb and WiFi. This also adds the base support for the 'Creator Ci40 (marduk)' device which uses the Pistachio SoC to create an IoT hub by including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x Mikrobus ports are available to expand with further RF technologies or add sensors. You can find out more here http://creatordev.io. Note, this commit is just the initial board support hence the following are not expected to work yet: * WiFi * Bluetooth * 6lowpan * Audio * Mikrobus uarts, user leds (clock dependency of 6lowpan chip) The aim of this commit is to essentially have the same level of support that currently exists in the mainline kernel. Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com> Signed-off-by: Francois Berder <francois.berder@imgtec.com> Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com> Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com> Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
* lantiq: remove lantiq_board_name, use the generic function insteadFelix Fietkau2017-03-221-2/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* package/uboot-envtools: add OpenMesh A40 supportSven Eckelmann2017-02-141-0/+1
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* package/uboot-envtools: add OpenMesh a60 supportSven Eckelmann2017-02-141-0/+1
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* package/uboot-envtools: add OpenMesh OM2Pv4/-HSv4 supportSven Eckelmann2017-02-141-1/+3
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* uboot-envtools: add nsa325 envsAlberto Bursi2017-02-111-0/+1
| | | | | | adding nsa325 envs for consistency with other kirkwoods Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* uboot-envtools: add nsa310b envsAlberto Bursi2017-01-241-0/+1
| | | | | | | accessing the u-boot's envs on this device is required to read the mac address. These are the envs of the new u-boot, not of the stock one. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* uboot-envtools: drop executable file attribute from files/ipqPiotr Dymacz2016-12-201-0/+0
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: fix Edimax BR-6425 board namePiotr Dymacz2016-12-201-1/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 14:01:50 +0000