aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.14 to 4.14.144Koen Vandeputte2019-09-208-182/+99
| | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 816-pcie-support-layerscape.patch Fixes: -CVE-2019-15030 Compile-tested on: cns3xxx, layerscape Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.193Koen Vandeputte2019-09-201-2/+2
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-15030 Compile-tested on: none Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: add support for EnGenius ESR600Nick Briggs2019-09-204-1/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit Ethernet switch, a gigabit Ethernet WAN port and a USB port. Specification: - Bootloader: U-Boot - SoC: MediaTek MT7620A (600 MHz) - Flash: 16MB, Macronix MX25L12845E - RAM: 64MB, Nanya NT5TU32M16DG-AC - Serial: 115200 baud, no header, 3.3V J2: Vcc (arrow), Gnd, Tx, Rx - USB: USB 2, 5V - Ethernet: 5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327 - WiFi0: 5 GHz 802.11 b/g/n Ralink RT5592N 300 Mb/s, 2T2R - WiFi1: 2.4 GHz 802.11 b/g/n integrated 300 Mb/s, 2T2R - Antennas: 2 per radio, internal - LEDs: 1 programmable power (amber) 2 programable radio (blue) 1 programable WPS-5G (blue) 1 non-programable WAN activity (blue) 1 unconfigured WPS-2.4G (amber) - Buttons: GPIO: Reset, WPS Installation: Use the OEM web interface to install the ...-factory.dlf image. Use the OpenWRT ...-sysupgrade.bin image for future upgrades. The J2 serial port can be accessed either by soldering in a header, standard 0.1" spacing, or by using pogo-pins against the back side. As configured by the OEM, the U-Boot boot delay is short, however quickly typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP" prompt. The TFTP client is configured by default with client: 192.168.99.9 server: 192.168.99.8 filename: uImageESR600 It will load an OpenWRT initramfs kernel with this method. Known issues: 1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational. LAN1 and LAN2 do not appear to power up. This issue is also present in the Lava LR25G001. 2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED, is not configured in the Device Tree specification. 3) The blue WAN activity LED is not configured in the Device Tree specification as this causes the AR8327 switch to fail to initialize. Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com> [merge conflict in 02_network] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7621: Add new device AsiaRF AP7621-NV1Daniel Danzberger2019-09-205-115/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Mediatek MT7621A CPU: 4x 880Mhz Cache: 32 KB I-Cache and 32 KB D-Cach 256 KB L2 Cache (shared by Dual-Core) RAM: DDR3 512MB 16bits BUS FLASH: 16MB Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN) POE: (1x PD, 2x PSE) USB: 1x 3.0 PCI: 3x Mini PCIe (3 USB2.0 + 2 x UIM interface) GPS: Quectel L70B SIM: 2 Slots BTN: Reset LED: - Power - Ethernet - Wifi - USB UART: UART is present as Pads with throughholes on the PCB. They are located on left side. 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ The stock image is a modified openwrt and can be overflashed via sysupgrade -F Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com> [merge conflict in mt7621.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Asus RT-AC85PBirger Koblitz2019-09-205-12/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT dual-core @ 880MHz RAM: 256M (Winbond W632GG6KB-1) FLASH: 128MB (Macronix MX30LF1G18AC-TI) WiFi: - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x USB 3.1 (Gen 1) BTN: Reset, WPS LED: - Power (blue) - 5Ghz (blue) - 2.4GHz (blue) - Internet (blue) - 4x LAN (blue) (LAN/WAN leds are not controllable by GPIOs) UART: UART is present as Pads marked J4 on the PCB. 3.3V - TX - RX - GND / 57600-8N1 3.3V is the square pad MAC: The MAC address on the router-label matches the MAC of the 2.4 GHz WiFi. LAN and WAN MAC are identical: MAC_LABEL+4 5 GHz WiFi MAC: also MAC_LABEL+4 Installation ------------ Via U-Boot tftpd: Switch on device, within 2s press reset button and keep pressed until power LED starts blinking slowly. Upload factory image via tftp put, the router's ip is 192.168.1.1 and expects the client on 192.168.1.75. The images also work on the Asus RT-AC65P models as tested by Gabor. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Tested-by: Gabor Varga <vargagab@gmail.com> [fixed Asus -> ASUS in DTS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Edimax RG21SBirger Koblitz2019-09-203-0/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT dual-core @ 880MHz RAM: 256M (Nanya NT5CC128M) FLASH: 16MB (Macronix MX25L12835F) WiFi: - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) USB: No BTN: Reset, WPS LED: 4 red LEDs, indistinguishable when casing closed UART: UART is present as Pads marked J1 on the PCB. 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the OEM web-interface (by default:http://192.168.1.1) The sysupgrade image can be installed via TFTP from the U-Boot bootloader. Connect ethernet port 2. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [flash node rename, EDIMAX -> Edimax, complete device model name] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* brcm2708: fix Hifiberry DAC+DSP package definitionÁlvaro Fernández Rojas2019-09-201-1/+1
| | | | | Fixes: ce536ae ("brcm2708: add support for Hifiberry DAC+DSP") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: Correctly search for the FIT image in mtd partition.Fredrik Olofsson2019-09-191-2/+2
| | | | | | Previously all iterations of the loop checked offset=0 in the partition. Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
* build: make device tree arg really optional in mkits.shJohann Neuhauser2019-09-191-5/+4
| | | | | | | | | If no device tree is given there is no node generated, but the configuration does still include the name of the missing node. This will result in a successful build fit image, but bootm does throw a error message if we want to boot the bad configuration. Signed-off-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
* lantiq-dsl: fix value of FECS counterMartin Schiller2019-09-191-13/+7
| | | | | | | Instead of the nFECS value, the nFEC value (the number of corrected code words) was mistakenly used. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* kernel: add module for Emulex OneConnect 10GbitAlberto Bursi2019-09-191-0/+21
| | | | | | | | add module to support Emulex OneConnect common in 10Gbit SFP+ cards by Dell/HP/IBM supports OneConnect OCe10xxx OCe11xxx OCe14xxx, LightPulse LPe12xxx Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* hostapd: declare struct wpa_bss earlyLeon M. George2019-09-191-0/+19
| | | | | | | | | | | | | | | | wps_supplicant.h assumes that 'struct wpa_bss' is forward declared if CONFIG_WPS is not defined. With the later inclusion of 600-ubus_support, the issue manifests in warnings like these: wps_supplicant.h:113:15: warning: 'struct wpa_bss' declared inside parameter list will not be visible outside of this definition or declaration struct wpa_bss *bss) ^~~~~~~ This patch forward declares 'struct wpa_bss' regardless. Signed-off-by: Leon M. George <leon@georgemail.eu> [commit message facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* hostapd: revert signature change in patchLeon M. George2019-09-191-1/+1
| | | | | | | | | | | | The original wpa_hexdump uses a 'void *' for the payload. With patch 410-limit_debug_messages, the signature changes and compiler warnings occur at various places. One such warning is: wpa_debug.h:106:20: note: expected 'const u8 * {aka const unsigned char *}' but argument is of type 'struct wpa_eapol_key *' Signed-off-by: Leon M. George <leon@georgemail.eu> [commit message facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add SUPPORTED_DEVICES to ubnt_nanostation-m-xwRoger Pueyo Centelles2019-09-191-1/+1
| | | | | | | | | | | | | | | | The ar71xx images for the Ubiquiti NanoStation M (XW) devices use "nanostation-m-xw" as the board name, but the ath79 images are only compatible with the "nano-m-xw" board name, so sysupgrade complains. By adding this additional supported device, sysuspgrade smoothly upgrades from ar71xx to ath79. Tested on a NanoStation M (XW) running OpenWrt ar71xx r10250-016d1eb. Ref: https://github.com/openwrt/openwrt/pull/2418 Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [removed duplicate DEVICE_VARIANT, removed uneeded nano-m-xw support] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add XM device variant for Ubiquiti devicesAdrian Schmutzler2019-09-191-2/+2
| | | | | | | | | | So far, XW devices have DEVICE_VARIANT defined and XM devices have no DEVICE_VARIANT set. This adds DEVICE_VARIANT for XM devices, and moves definitions for both XM and XW to the common definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: provide label MAC addressAdrian Schmutzler2019-09-1932-10/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the label MAC address for several devices in ramips. Some devices require setting the MAC address in 02_network: For the following devices, the netif device can be linked in device tree, but the MAC address cannot be read: - cudy,wr1000 - dlink,dir-615-d - dlink,dir-615-h1 - dlink,dir-860l-b1 - glinet,gl-mt300a - glinet,gl-mt300n - glinet,gl-mt750 - vocore,vocore2 - vocore,vocore2-lite - zbtlink,zbt-we1326 - zbtlink,zbt-wg3526 For the following devices, label MAC address is tied to lan or wan, so no node to link to exists in device tree: - dlink,dir-510l - dlink,dwr-116-a1 - dlink,dwr-118-a1 - dlink,dwr-118-a2 - dlink,dwr-921-c1 - dlink,dwr-922-e2 - all hiwifi devices - lava,lr-25g001 - xiaomi,mir3p Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: provide label MAC addressAdrian Schmutzler2019-09-192-0/+2
| | | | | | | This patch adds the label MAC address for several devices in ipq806x. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mpc85xx: provide label MAC addressAdrian Schmutzler2019-09-192-0/+2
| | | | | | | This patch adds the label MAC address for some devices in mpc85xx. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: provide label MAC addressAdrian Schmutzler2019-09-1954-12/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the label MAC address for several devices in ath79. Some devices require setting the MAC address in 02_network: For the following devices, the netif device can be linked in device tree, but the MAC address cannot be read: - alfa-network,ap121f - avm,fritz300e - ubnt-xm devices For the following devices, label MAC address is tied to lan or wan, so no node to link to exists in device tree: - adtran,bsap1800-v2 - adtran,bsap1840 - dlink,dir-842-c1/-c2/-c3 - engenius,ecb1750 - iodata,etg3-r - iodata,wn-ac1167dgr - iodata,wn-ac1600dgr - iodata,wn-ac1600dgr2 - iodata,wn-ag300dgr - nec,wg800hp - nec,wg1200cr - trendnet,tew-823dru Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* base-files: provide option to specify label MAC address in board.dAdrian Schmutzler2019-09-193-0/+14
| | | | | | | | | | | | | | For many devices, MAC addresses cannot be retrieved via the device tree alias. To still provide the label MAC address for those, this implements a second mechanism that will put the address into uci config. Note that this stores the actual MAC address, whereas in DTS we reference the bearing device. This is based on the work of Rosy Song <rosysong@rosinson.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* base-files: add function to retrieve label MAC addressAdrian Schmutzler2019-09-191-0/+10
| | | | | | | | | | | | | | | | To refer to the MAC address on a device's label, one can specify the alias label-mac-device in the DTS which should point to the bearer of the corresponding MAC address. With the function get_mac_label, the user can retrieve then retrieve this address and use it as a value that uniquely identifies his device. This is severely helpful for several downstream functionalities, e.g. define MAC addresses of custom netifs or change the SSID to be easily recognizable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* curl: bump to 7.66.0Hans Dedecker2019-09-192-4/+4
| | | | | | | | | | Refresh patches, for changes in version 7.66.0 see https://curl.haxx.se/changes.html#7_66_0 Fixes CVEs: CVE-2019-5481 CVE-2019-5482 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* openssl: bump to 1.1.1dEneas U de Queiroz2019-09-1912-2524/+223
| | | | | | | | | | | | | This version fixes 3 low-severity vulnerabilities: - CVE-2019-1547: ECDSA remote timing attack - CVE-2019-1549: Fork Protection - CVE-2019-1563: Padding Oracle in PKCS7_dataDecode and CMS_decrypt_set1_pkey Patches were refreshed. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* brcm2708: add support for Hifiberry DAC+DSPÁlvaro Fernández Rojas2019-09-191-0/+20
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm2708: add support for Raspberry Pi 2B 1.2Álvaro Fernández Rojas2019-09-193-5/+18
| | | | | | RPi 2B 1.2 has a BCM2710/BCM2837 like RPi 3 devices. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm2708: update to latest patches from RPi foundationÁlvaro Fernández Rojas2019-09-19806-1570/+3639
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm2708-gpu-fw: update to latest firmwareÁlvaro Fernández Rojas2019-09-191-15/+15
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: 4.19: fix crash when setting up spi-gpioDENG Qingfang2019-09-191-0/+66
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If an spi-gpio was specified with num-chipselects = <0> in dts, kernel will crash: Unable to handle kernel paging request at virtual address 32697073 pgd = (ptrval) [32697073] *pgd=00000000 Internal error: Oops: 5 [# 1] SMP ARM Modules linked in: CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.19.72 #0 Hardware name: Generic DT based system PC is at validate_desc+0x28/0x80 LR is at gpiod_direction_output+0x14/0x128 ... [<c0544db4>] (validate_desc) from [<c0545228>] (gpiod_direction_output+0x14/0x128) [<c0545228>] (gpiod_direction_output) from [<c05fa714>] (spi_gpio_setup+0x58/0x64) [<c05fa714>] (spi_gpio_setup) from [<c05f7258>] (spi_setup+0x12c/0x148) [<c05f7258>] (spi_setup) from [<c05f7330>] (spi_add_device+0xbc/0x12c) [<c05f7330>] (spi_add_device) from [<c05f7f74>] (spi_register_controller+0x838/0x924) [<c05f7f74>] (spi_register_controller) from [<c05fa494>] (spi_bitbang_start+0x108/0x120) [<c05fa494>] (spi_bitbang_start) from [<c05faa34>] (spi_gpio_probe+0x314/0x338) [<c05faa34>] (spi_gpio_probe) from [<c05a844c>] (platform_drv_probe+0x34/0x70) The cause is spi_gpio_setup() did not check if the spi-gpio has chipselect pins before setting their direction and results in derefing an invalid pointer. The bug is spotted in kernel 4.19.72 and does not occur in 4.14. There is a similar fix upstream in kernel 5.2 in commit 249e2632dcd0 ("spi: gpio: Don't request CS GPIO in DT use-case"). Ref: https://patchwork.kernel.org/patch/11150619/ Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [use upstream patch, moved from hack to pending dir, commit facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* procd: fix invalid JSON filter expression in procd_running()Jo-Philipp Wich2019-09-192-2/+2
| | | | | | | | | Since service and instance names may contain characters which are not allowed in JSON path labels, such as dashes or spaces, change the filter expression to array square bracket notation to properly match these cases as well. Fixes: 2c3dd70741 ("procd: add procd_running() helper for checking running state") Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* firewall: update to latest Git HEADJo-Philipp Wich2019-09-181-3/+3
| | | | | | | 383eb58 ubus: do not overwrite ipset name attribute Ref: https://forum.openwrt.org/t/fw3-ipset-procd-objects/44044 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* procd: update to the latest git HEADRafał Miłecki2019-09-181-3/+3
| | | | | | | 62dc8c0 system: sysupgrade: send reply on error 2710c65 system: refuse sysupgrade with backup if it's unsupported Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* glibc: update to latest 2.27 commit (BZ#23637)Hans Dedecker2019-09-171-2/+2
| | | | | | | | | | | | 5b4f7382af Add undef to fix test failure. 9456483fb2 Improve performance of memmem 373f8b06a3 Improve performance of strstr 4ec1b9e913 Fix strstr bug with huge needles (bug 23637) ecd6271ed8 Speedup first memmem match bba6b9288f Simplify and speedup strstr/strcasestr first match 7a4da6ef7a Improve strstr performance Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath79: add support for TP-Link Archer C59v2Keith Maika2019-09-165-1/+102
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add ath79 support for Archer C59v2, previously supported by ar71xx. TP-Link Archer C59v2 is a dual-band AC1350 router based on Qualcomm/Atheros QCA9561+QCA9886 chips. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - UART header on PCB Flash instruction: - via web UI: 1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin 2. Login to router and open the Advanced tab 3. Navigate to System Tools -> Firmware Upgrade 4. Upload firmware using the Manual Upgrade form - via TFTP: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Keith Maika <keithm@aoeex.com>
* ath79: move common definitions from Archer C58/C59 to common DTSIAdrian Schmutzler2019-09-163-143/+74
| | | | | | | | | The Archer C58/C59 have redundant LED and MAC address definitions in their DTS files. This moves them to the parent DTSI file. The patch already accounts for the upcoming Archer C59 v2. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* brcm47xx: sysupgrade: support Luxul firmware formatDan Haab2019-09-161-0/+82
| | | | | | Allow flashing Luxul devices using vendor firmware format. Signed-off-by: Dan Haab <dan.haab@legrand.com>
* bcm53xx: sysupgrade: support Luxul firmware formatDan Haab2019-09-161-0/+84
| | | | | | | Allow flashing Luxul devices using vendor firmware format. The next step will be building proper images once they are conirmed to work. Signed-off-by: Dan Haab <dan.haab@legrand.com>
* download.dl: fix @KERNEL mirror urlsYousong Zhou2019-09-161-4/+4
| | | | | | | - Prepend "/pub" for mirror.rackspace.com - Use https for download.xs4all.nl and mirrors.mit.edu Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* mac80211: brcmfmac: backport the last 5.4 changesRafał Miłecki2019-09-164-1/+413
| | | | | | | This makes brcmfmac use the same wiphy after PCIe reset to help user space handle corner cases (e.g. firmware crash). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: fix typo in platform_do_upgrade_compex()Rafał Miłecki2019-09-161-1/+1
| | | | | Fixes: 641f6b6c26cb ("treewide: use new procd sysupgrade $UPGRADE_BACKUP variable") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: enable mtk_efuse by defaultLorenzo Bianconi2019-09-151-1/+1
| | | | | | | Enable by default mtk_efuse driver since it needed by mtk_thermal driver to read sensor calibration data Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
* ath79: eg200: enable status led usageKarl Palsson2019-09-152-2/+4
| | | | | | | | | This enables using the "eTactica" LED during boot, to indicate failsafe, and during upgrade, while still leaving the LED alone for normal operation. This brings the device more in line with how other devices work, and makes the failsafe functionality easier to use and understand. Signed-off-by: Karl Palsson <karlp@etactica.com>
* firewall: update to latest git HEADPetr Štetiar2019-09-151-3/+3
| | | | | | c26f8907d1d2 firewall3: fix typo that affects ICMPv6 rules with numeric icmp_type Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath10k-ct: update to version 2019-09-09Robert Marko2019-09-159-18/+18
| | | | | | | | | Update the ath10k-ct driver version to 5e8cd86f90dac966d12df6ece84ac41458d0e95f to enable dynamic VLANs to work. Patches refreshed during the bump. Signed-off-by: Robert Marko <robimarko@gmail.com> [commit description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath10k-firmware: update Candela Tech firmware imagesRobert Marko2019-09-151-20/+20
| | | | | | | This enables a feature flag in the wave-2 firmware wmi-services indicating it can send software-encrypted raw frames. This should in turn allow the AP-VLAN feature to work. Signed-off-by: Robert Marko <robimarko@gmail.com>
* scons: move to packages feedPetr Štetiar2019-09-155-85/+1
| | | | | | | | | | | | | | This patch removes scons host build tool, as commit 7087efd72a8d ("scons: move host build tool to a proper place") in the packages feed has moved scons into the new home. There are currently no packages in the master tree which would need scons, yet scons is build always as part of host tools, just in order to satisfy host build dependency of few packages in the packages feeds. Ref: https://github.com/openwrt/packages/pull/9584 Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* netifd,lldpd,rpcd,log: use generic service_runningPetr Štetiar2019-09-154-17/+0
| | | | | | | | | | | | | | | | | | commit eb204d14f75c ("base-files: implement generic service_running") introduced generic service_running so it's not needed to copy&paste same 3 lines over and over again. I've removed service_running from netifd/network init script as well, because it was not working properly, looked quite strange and I didn't understand the intention: $ /etc/init.d/network stop $ service network running && echo "yes" || echo "nope" ( have to wait for 30s ) Command failed: Request timed out yes Signed-off-by: Petr Štetiar <ynezz@true.cz>
* base-files,procd: add generic service statusLuiz Angelo Daros de Luca2019-09-152-1/+35
| | | | | | | | | | | | | | Adds a default status action for init.d scripts. procd "service status" will return: 0) for loaded services (even if disabled by conf or dead) 3) for inactive services 4) when filtering a non-existing instance Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> [rebased, cleaned up] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* base-files: implement generic service_runningPetr Štetiar2019-09-151-1/+6
| | | | | | | DRY is good, otherwise we're going to suffer with a copy&paste disease in the init scripts. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* odhcpd: update to latest git HEADHans Dedecker2019-09-151-3/+3
| | | | | | | | 1d24009 netlink: rename netlink callback handlers 91a28e4 ndp: answer global-addressed NS manually fd93e36 dhcpv6: retry failed PD assignments on addrlist change Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: add SD-Card support for Linkit Smart 7688Ivan Hörler2019-09-151-1/+1
| | | | | | The Linkit Smart 7688 has a SD-Card reader that does not work with the official build of openwrt. Adding kmod-sdhci-mt7620 makes it working. Signed-off-by: Ivan Hörler <i.hoerler@me.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 04:02:09 +0000