aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* firmware-utils: bcm4908img: support extracting bootfs & rootfsRafał Miłecki2021-04-071-0/+35
| | | | | | | It's required for upgrading firmware using single partitions instead of just blindly writing whole image. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: replace size with offsetRafał Miłecki2021-04-071-20/+35
| | | | | | | It's much easier to operate on BCM4908 image data with absolute offset of each section stored. It doesn't require summing sizes over and over. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: ar934x-nand: fix broken nand on kernel 5.10Koen Vandeputte2021-04-061-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Booting current 5.10.x testing kernel shows this: [ 0.335781] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 0.342280] nand: Samsung NAND 128MiB 3,3V 8-bit [ 0.346982] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.354703] ar934x-nand 1b800200.nand: unknown ECC mode 2 [ 0.360193] ar934x-nand 1b800200.nand: nand_scan failed, err:-22 [ 0.366341] ar934x-nand: probe of 1b800200.nand failed with error -22 ... [ 1.089264] /dev/root: Can't open blockdev [ 1.093482] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 1.101077] Please append a correct "root=" boot option; here are the available partitions: [ 1.109555] 1f00 64 mtdblock0 [ 1.109559] (driver?) [ 1.116199] 1f01 48 mtdblock1 [ 1.116202] (driver?) [ 1.122841] 1f02 4 mtdblock2 [ 1.122844] (driver?) [ 1.129493] 1f03 4 mtdblock3 [ 1.129497] (driver?) [ 1.136138] 1f04 4 mtdblock4 [ 1.136142] (driver?) [ 1.142787] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 1.151168] Rebooting in 1 seconds.. The issue is caused by a wrong check for ECC engine type on newer kernels. Fix this. Bootlog after: [ 0.335689] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 0.342192] nand: Samsung NAND 128MiB 3,3V 8-bit [ 0.346884] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.354611] Scanning device for bad blocks [ 0.364924] random: fast init done [ 0.496641] 3 fixed-partitions partitions found on MTD device ar934x-nand [ 0.503545] Creating 3 MTD partitions on "ar934x-nand": [ 0.508865] 0x000000000000-0x000000040000 : "booter" [ 0.515133] 0x000000040000-0x000000400000 : "kernel" [ 0.523265] 0x000000400000-0x000008000000 : "ubi" Fixes: fb64e2c30f ("ath79: ar934x-nand: add kernel 5.10 compatibility") Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* bcm4908: rename bootfs dummy file to the 1-openwrtRafał Miłecki2021-04-061-1/+1
| | | | | | | | | | | | The purpose of that dummy file is to make CFE work properly with OpenWrt bootfs. CFE for some reason ignores JFFS2 files with ino 0. Rename it to 1-openwrt so: 1. It's consistent with bcm63xx 2. It's OpenWrt specific so sysupgrade can distinguish it from vendor images Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* glibc: update to latest git HEAD (BZ #27468, BZ #27511)Hans Dedecker2021-04-051-2/+2
| | | | | | | | e78ea9bd26 Update Nios II libm-test-ulps. 98bb18f52a malloc: Fix a realloc crash with heap tagging [BZ 27468] fc4ecce85b S390: Also check vector support in memmove ifunc-selector [BZ #27511] Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* uboot-mediatek: update to v2021.04Daniel Golle2021-04-059-79/+8
| | | | | | | | | | Remove patches merged upstream and refresh the remaining ones. Runtime tested on * Bananapi BPi-R64 (eMMC and SD Card) * Linksys E8450 (SPI-NAND) * Ubiquiti UniFi 6 LR (SPI-NOR) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* lldpd: further size reductionsStijn Tintel2021-04-051-2/+2
| | | | | | | | | | | Size difference on mips_4kec: Before: 120196 After: 120006 Closes https://github.com/openwrt/openwrt/pull/3823 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Suggested-by: Lucian Cristian <lucian.cristian@gmail.com>
* lldpd: enable LTOStijn Tintel2021-04-051-1/+4
| | | | | | | | | Size difference on mips_4kec: W/o LTO: 139674 W/ LTO: 120196 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Suggested-by: Lucian Cristian <lucian.cristian@gmail.com>
* lldpd: bump to 1.0.9Stijn Tintel2021-04-052-64/+3
| | | | | | Contains fixes related to CVE-2020-27827. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* lldpd: add libcap dependencyStijn Tintel2021-04-052-19/+2
| | | | | | | | | Now that libcap is in OpenWrt base, we can drop our custom patch to disable libcap support and have lldpd depend on it instead. This will allow the monitor process to drop its privileges instead of running as root, improving security. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* libcap: bump to 2.48Stijn Tintel2021-04-051-2/+2
| | | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* libcap: drop invalid copyright headerStijn Tintel2021-04-051-2/+0
| | | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* libcap: import from packages feedStijn Tintel2021-04-052-0/+126
| | | | | | | | | | | | Having libcap in OpenWrt base allows us to enable libcap support in other packages in base. In lldpd, this would allow the monitor process to drop its privileges instead of running as root, improving security. It will also allow us to drop our patch to disable libcap. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm4908: enable JFFS2 supportRafał Miłecki2021-04-051-1/+0
| | | | | | It's needed for accessing JFFS2 bootfs partition. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: add bootfs supportRafał Miłecki2021-04-051-3/+337
| | | | | | | | | | | | This adds support for accessing bootfs JFFS2 partition in the BCM4908 image. Support includes: 1. Listing files 2. Renaming file (requires unchanged name length) Above commands are useful for flashing BCM4908 images which by defualt come with cferom.000 file and require renaming it. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: support extracting image dataRafał Miłecki2021-04-051-0/+87
| | | | | | It's useful for upgrading cferom, firmware, etc. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: find cferom sizeRafał Miłecki2021-04-051-0/+31
| | | | | | | It's important for modifying / extracting firmware content. cferom is optional image content at the file beginning. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: use "info" command displaying file infoRafał Miłecki2021-04-051-11/+20
| | | | | | | BCM4908 image format contains some info that may be useful for info / debugging purposes. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: support reading from stdinRafał Miłecki2021-04-051-8/+38
| | | | | | | 1. Don't allow pipe stdin as we need to fseek() 2. Don't alow TTY as it doesn't make sense for binary input Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: detect Netgear vendor firmwareRafał Miłecki2021-04-051-25/+33
| | | | | | | | Netgear uses CHK header which needs to be skipped when validating BCM4908 image. Detect it directly in the bcm4908img tool. Dealing with binary structs and endianess is way simpler in C. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: extract parsing codeRafał Miłecki2021-04-051-37/+67
| | | | | | | | Move code parsing existing firmware file to separated function. This cleans up existing code and allows reusing parsing code for other commands. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ipq40xx: add MikroTik hAP ac2 supportRobert Marko2021-04-058-1/+316
| | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC (hAP ac²), a indoor dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional antennae, USB port and five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac2 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 128 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in - 1x USB Type A port Installation: Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com>
* uboot-mediatek: bpi-r64: no longer force recovery on first-bootDaniel Golle2021-04-041-4/+4
| | | | | | | | Now that sdcard.gz image contains everything needed to boot straight into production image, no longer force booting into recovery image on first boot by removing the logic which implemented that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mt76: update to the latest versionFelix Fietkau2021-04-041-3/+3
| | | | | | | | | | | | | | | | 465dda65ee84 mt7615,mt7915: replace fw log 0-terminating code with wiphy info length limit 62b13f5352b8 mt76: mt7921: fix key set/delete issue 0ff3a336a8d8 mt7615,mt7915: fix a compiler warning 113ba8a81d54 mt76: mt7615: remove redundant dev_err call in mt7622_wmac_probe() be1ab3b9ae7c mt76: mt7921: fix typo in mt7921_pci_resume 4e22f0dc934b mt76: mt7915: fix txpower init for TSSI off chips e66a0b9b8d66 mt76: mt7615: always wake the device in mt7615_remove_interface 38f656768a90 mt76: mt7921: always wake the device in mt7921_remove_interface 6ee4770de083 mt76: mt7921: rework mt7921_mcu_debug_msg_event routine e578b4b8d56a mt76: mt7615: fix .add_beacon_offload() f8c6c7cbf10f mt76: mt7915: fix mt7915_mcu_add_beacon Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 5.10 to 5.10.27Kevin Darbyshire-Bryant2021-04-0321-60/+64
| | | | | | | | | | | | | | | | Use update_kernel to refresh all patches, required manual updates to: 610-netfilter_match_bypass_default_checks.patch 611-netfilter_match_bypass_default_table.patch 762-net-bridge-switchdev-Refactor-br_switchdev_fdb_notif.patch 764-net-bridge-switchdev-Send-FDB-notifications-for-host.patch Run-tested: x86_64 Nothing screamed out but any funny business with linux bridging should suspect this update first. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* netifd: update to Git version 2021-04-03Hauke Mehrtens2021-04-031-3/+3
| | | | | | | f8899b9 netifd: bridge: set default value for igmp_snoop 327da98 netifd: add possibility to switch off route config Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uclient: update to Git version 2021-04-03Hauke Mehrtens2021-04-031-3/+3
| | | | | | | 83efca2 tests: fix possibly longer start of HTTP server 64e00d6 uclient-fetch: document missing options Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* hostapd: enable airtime policy for the -basic variantsRui Salvaterra2021-04-031-1/+1
| | | | | | | | | | | | | | Airtime policy configuration is extremely useful in multiple BSS scenarios. Since nowadays most people configure both private and guest networks (at least), it makes sense to enable it by default, except for the most limited of the variants. Size of the hostapd-basic-openssl binary (mipsel 24Kc -O2): 543944 bytes (airtime policy disabled) 548040 bytes (airtime policy enabled) Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> Acked-by: Daniel Golle <daniel@makrotopia.org>
* realtek: rename partitions in Netgear DTSIStijn Segers2021-04-031-5/+5
| | | | | | | | | Switch the Netgear DTSI for the Realtek target from the OEM partition naming scheme to accepted OpenWrt naming practices. A quick git grep for 'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* zram-swap: bail out early if the kernel doesn't support swapRui Salvaterra2021-04-031-0/+5
| | | | | | | | Since KERNEL_SWAP is only enabled by default for !SMALL_FLASH targets, we need to check if the current kernel supports swap before trying to configure zram-swap, as opkg can't check for kernel dependencies. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* zram-swap: clean up the makefileRui Salvaterra2021-04-031-3/+9
| | | | | | | Break dependencies into separate lines, to improve the readability. Trim trailing whitespace. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* lantiq: add basic support for AVM FRITZ!Box 3390Andreas Böhler2021-04-036-1/+328
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The FRITZ!Box 3390 actually contains two SoCs, one Lantiq with a 5GHz WiFi and one AR9342 with a 2.4GHz WiFi. Only the Lantiq has access to the flash memory, the Atheros runs fully from RAM. Specifications -------------- - Lantiq 500 MHz - 128MiB RAM - 128MiB NAND - 256k Flash - AR9580 5GHz WiFi - AR9342 560 MHz - 64MiB RAM - AR9328 2.4GHz WiFi Remarks ------- This commit only adds support for the Lantiq side of things and prepares the drivers for communication with the Atheros SoC. Thus, only 5GHz WiFi works by default, the 2.4GHz WiFi will be added via another target. Some kernel patches will be required to add support for the Atheros SoC. Installation ------------ Use the eva_ramboot.py script to boot the initramfs image. Then, transfer the sysupgrade image to the device and run sysupgrade to flash it to the NAND. Signed-off-by: Andreas Böhler <dev@aboehler.at> Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
* lantiq: VR9: fix gpio-hog by defining the GPIO rangesJoachim Cerny2021-04-031-0/+1
| | | | | | | | | | defined gpio-ranges according to Reference: https://github.com/torvalds/linux/blob/master/drivers/pinctrl/pinctrl-xway.c#L864 This change is needed by gpio-hog on Fritzbox 3390 thx to @abajk Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl Signed-off-by: Andreas Böhler <dev@aboehler.at> Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
* lantiq: use ActualNetDataRate for speed reportingJeroen Peelaerts2021-04-032-1/+6
| | | | | | | | | | | | | Switch to Actual Net Data Rate (ACTNDR) for speed reporting on lantiq VDSL modems Refer to ITU-T G.997.1 chapter 7.5.2.8 Independent whether retransmission is used or not in a given transmit direction: - In L0 state, this parameter reports the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) at which the bearer channel is operating. - In L2 state, the parameter contains the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) in the previous L0 state. Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com> Reviewed-by: Andre Heider <a.heider@gmail.com>
* lantiq: enable G.INP retransmission countersJeroen Peelaerts2021-04-032-3/+7
| | | | | | | | | | | | | | | | This commit adds monitoring for a couple of DSL line features that are present in the lantiq firmware blobs. * G.INP ON/OFF * Trellis encoding ON/OFF * Virtaul Noise ON/OFF * Bitswap ON/OFF Difference in size for ltq-vdsl-app = 1k Difference in size for kmod-ltq-vdsl-vr9 < 1k Reviewed-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
* ramips: fix IMAGE_SIZE of HC5x6: fix image size of HC5x61Shiji Yang2021-04-031-3/+3
| | | | | | | | "firmware" partition size defined in the device tree file is 0xf70000, so the right IMAGE_SIZE is 15808k Fixes: df1e5d646345 ("ramips: fix partition layout of hiwifi hc5x61") Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: Fix booting on MQmaker WiTi boardDaniel Engberg2021-04-031-0/+1
| | | | | | | | This fixes the dreaded "lzma error 1" also reported on similar devices Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057 Fixes: FS#3057 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ramips: Fix booting on MTC WR1201René van Dorst2021-04-031-0/+1
| | | | | | | | This fixes the dreaded "lzma error 1" also reported on similar devices Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057 Fixes: FS#3057 Signed-off-by: René van Dorst <opensource@vdorst.com>
* armvirt: add 5.10 testing kernelAleksander Jan Bajkowski2021-04-031-0/+1
| | | | | | | Add 5.10 as testing kernel. Builds successfully with CONFIG_ALL_KMODS=y enabled. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* armvirt: refresh 5.10 configAleksander Jan Bajkowski2021-04-033-19/+20
| | | | | | | | | | This was done by executing these commands: $ make kernel_oldconfig CONFIG_TARGET=subtarget $ make kernel_oldconfig CONFIG_TARGET=subtarget_platform Some common symbols have been moved to target config. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* armvirt: copy config files for 5.10Aleksander Jan Bajkowski2021-04-033-0/+391
| | | | | | Copy config and patches for 5.10. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* armvirt: refresh 5.4 configAleksander Jan Bajkowski2021-04-033-203/+14
| | | | | | | | This was done by executing these commands: $ make kernel_oldconfig CONFIG_TARGET=subtarget $ make kernel_oldconfig CONFIG_TARGET=subtarget_platform Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* base-files: fix status display commandAlexander Egorenkov2021-04-031-1/+1
| | | | | | | | | | | | | | | | | | | | If service() is called w/o parameter then the status display for services with multiple instances is incorrect. E.g. samba4 or wpad have 2 instances. root@OpenWrt:~# /etc/init.d/samba4 status running root@OpenWrt:~# /etc/init.d/wpad status running Before change: /etc/init.d/samba4 enabled stopped /etc/init.d/wpad enabled stopped After change: /etc/init.d/samba4 enabled running /etc/init.d/wpad enabled running Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
* iproute2: fix libbpf detection with NLS enabledTony Ambardar2021-04-032-1/+21
| | | | | | | | | | | | | | | | | Upstream iproute2 detects libbpf using a one-line $CC test-compile, which normally ignores LDFLAGS. With NLS enabled however, LDFLAGS includes an "rpath-link" linker option needed to resolve libintl.so. Its absence causes both the compile and libbpf detection to fail: ld: warning: libintl.so.8, needed by libbpf.so, not found (try using -rpath or -rpath-link) ld: libelf.so.1: undefined reference to `libintl_dgettext' collect2: error: ld returned 1 exit status Fix this by directly including $LDFLAGS in the test-compile command. Reported-by: Ian Cooper <iancooper@hotmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* binutils: fix libbfd missing DSO dependency if NLS enabledTony Ambardar2021-04-031-2/+4
| | | | | | | | | | | | | | | | | | | | | | | The libbfd package definition uses $(ICONV_DEPENDS) and $(INTL_DEPENDS) but links against neither, leading to libbfd detection failures in other packages (e.g. bpftools) and on-target relocation problems with libintl.so: root@OpenWrt:/# ldd /usr/lib/libbfd.so ldd (0x77db6000) libc.so => ldd (0x77db6000) libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77c6d000) Error relocating /usr/lib/libbfd.so: libintl_dgettext: symbol not found Add NLS-conditional linking of "libintl" to fix this. Also remove libbfd package dependency $(ICONV_DEPENDS) which is not used during building or linking. Tested with QEMU on malta/be32, after building all packages from binutils, bpftools and iproute2, using different libc options musl and glibc. Fixes: 08e817569630 ("binutils: use nls.mk to fix libbfd link errors in other packages") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* bpftools: drop unneeded libintl linking for NLSTony Ambardar2021-04-031-5/+1
| | | | | | | | There is no direct linking of libintl from bpftools, only secondary linking through libelf, so remove "-lintl" from TARGET_LDFLAGS. Fixes: 5582fbd6135f ("bpftools: support NLS, fix ppc build and update to 5.8.9") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel: bump 5.4 to 5.4.109John Audia2021-04-0257-182/+182
| | | | | | | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Manually rebased: pending-5.4/611-netfilter_match_bypass_default_table.patch The upstream change affecting this patch is the revert of an earlier kernel commit. Therefore, we just revert our corresponding changes in [1]. Build system: x86_64 Build-tested: ipq806x/R7800 [1] 9b1b89229f0e ("kernel: bump 5.4 to 5.4.86") Signed-off-by: John Audia <graysky@archlinux.us> [adjust manually rebased patch, add explanation] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm53xx: enhance support for Linksys EA9500Vivek Unune2021-04-014-3/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Add leds and configs 2. Add network configs 3. Add script to clear partial boot flag 4. Hack to use port 5 as cpu port as port 8 connected to eth2 wont pass any frames 5. Enable EA9500 image generation Hardware Info: - Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz - Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125 - DDR3 RAM - 256 MB - Flash - 128 MB (Toshiba TC58BVG0S3HTA00) - 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4) - 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch - Ports - 8 Ports, 1 WAN Ports - Antennas - 8 Antennas - Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1 Flashing Instructions: 1. Connect a USB-TTL table to J6 on the router as well as a ethernet cable to a lan port and your PC. 2. Power-on the router. 3. Use putty or a serial port program to view the terminal. Hit Ctrl+C and interrupt the CFE terminal terminal. 4. Setup a TFTP server on your local machine at setup you local IP to 192.168.1.2 5. Start the TFTP Server 6. Run following commands at the CFE terminal flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2 nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit 7. Reboot router to be presented by OpenWrt Note: Only installation method via serial cable is supported at the moment. The trx firmware has to be flashed to both the partitions using following commands from CFE prompt. This will cover US and Non-US variants. Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: use upstream Linksys EA9500 fixesRafał Miłecki2021-04-012-1/+30
| | | | | | One fix was accepted, one was added. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firewall4: update to latest Git HEADJo-Philipp Wich2021-04-011-3/+3
| | | | | | | | | | | | | 29fba84 tests: expand testing 6bf82a8 fw4.uc: fix family test functions 25b2c7d fw4.uc: fix parsing boolean "0" values 694d428 rule.uc: fix redundant whitespace in rules without target 7f69fbb ruleset.uc: reduce empty lines in output 8f8e42c fw4.uc: gracefully handle missing defaults section 25287af treewide: remove ucode module preloading 802b685 fw4.uc: remove upvalue caching Signed-off-by: Jo-Philipp Wich <jo@mein.io>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-11 14:24:31 +0000