aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* openssl: bump to 1.1.1fEneas U de Queiroz2020-04-012-83/+3
| | | | | | | | | There were two changes between 1.1.1e and 1.1.1f: - a change in BN prime generation to avoid possible fingerprinting of newly generated RSA modules - the patch reversing EOF detection we had already applied. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* oxnas: some improvements for Shuttle KD20Daniel Golle2020-03-313-7/+59
| | | | | | | | | * install kmod-hwmon-drivetemp by default * wire up thermal zone * fix fan GPIO polarity * fix i2c-gpio GPIO_OPEN_DRAIN Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: fix warning in SATA driverDaniel Golle2020-03-311-1/+1
| | | | | | | | | drivers/ata/sata_oxnas.c: In function 'sata_oxnas_port_irq': drivers/ata/sata_oxnas.c:2126:25: warning: left shift count >= width of type [-Wshift-count-overflow] if (ap->qc_active & (1 << ATA_TAG_INTERNAL)) { ^~ Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: fix DAP-2610 boot failurePetr Štetiar2020-03-311-0/+1
| | | | | | | | | | | | | Albert has reported, that his DAP-2610 wont boot with the latest snapshot and Fredrik has found out, that the device gets stuck at "Waiting for root device ..." due to missing 5.4 kernel config symbol CONFIG_MTD_SPLIT_WRGG_FW which was probably lost during the kernel version bump. Ref: https://forum.openwrt.org/t/dap-2610-bricked-help-needed Fixes: 272e0a702a2b ("ipq40xx: add v5.4 support") Suggested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* x86/64: add cdrom and iso9660 drivers李国2020-03-312-0/+8
| | | | | | | The iso image need cdrom and iso9660 drivers to boot, otherwise it will hang when mounting the root file system Signed-off-by: 李国 <uxgood.org@gmail.com>
* x86: generate EFI platform bootable images李国2020-03-3112-38/+165
| | | | | | | | | | | | | | | | | Add EFI platform bootable images for x86 platforms. These images can also boot from legacy BIOS platform. EFI System Partition need to be fat12/fat16/fat32 (not need to load filesystem drivers), so the first partition of EFI images are not ext4 filesystem any more. GPT partition table has an alternate partition table, we did not generate it. This may cause problems when use these images as qemu disk (kernel can not find rootfs), we pad enough sectors will be ok. Signed-off-by: 李国 <uxgood.org@gmail.com> [part_magic_* refactoring, removed genisoimage checks] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* grub2: make some change to add efi platform support李国2020-03-312-28/+55
| | | | | | | | 1.generate boot image at Package/install section 2.move boot image to $(STAGING_DIR_IMAGE)/grub2/ 3.add efi variant to support efi platform Signed-off-by: 李国 <uxgood.org@gmail.com>
* firmware-utils: ptgen: add GPT support李国2020-03-312-24/+319
| | | | | | | | | | | | | | | | Add GPT support to ptgen, so we can generate EFI bootable images. Introduced two options: -g generate GPT partition table -G GUID use GUID for disk and increase last bit for all partitions We drop The alternate partition table to reduce size, This may cause problems when generate vmdk images or vdi images. We have to pad enough sectors when generate these images. Signed-off-by: 李国 <uxgood.org@gmail.com> [fixed compilation on macOS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* bcm27xx-gpu-fw: update to latest version from RPi foundationÁlvaro Fernández Rojas2020-03-311-22/+15
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: update 5.4 patches from RPi foundationÁlvaro Fernández Rojas2020-03-3184-6/+7955
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* wireguard: bump to 1.0.20200330Jason A. Donenfeld2020-03-311-2/+2
| | | | | | | | | | | | | | | | | * queueing: backport skb_reset_redirect change from 5.6 * version: bump This release has only one slight change, to put it closer to the 5.6 codebase, but its main purpose is to bump us to a 1.0.y version number. Now that WireGuard 1.0.0 has been released for Linux 5.6 [1], we can put the same number on the backport compat codebase. When OpenWRT bumps to Linux 5.6, we'll be able to drop this package entirely, which I look forward to seeing. [1] https://lists.zx2c4.com/pipermail/wireguard/2020-March/005206.html Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* generic: mips: exclude more dsemul code when fpu-emu is not enabledYousong Zhou2020-03-301-0/+140
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch is backported from mips-next. In addition to minor reduction of code size and runtime memory use, the more apparent difference is that the delay slot emulation page will not be present for those targets with fpu emulation disabled (CONFIG_MIPS_FP_SUPPORT=n) Memory maps of busybox before and after this change root@OpenWrt:/# cat /proc/self/maps 00400000-00449000 r-xp 00000000 00:02 23 /bin/busybox 00458000-00459000 r-xp 00048000 00:02 23 /bin/busybox 00459000-0045a000 rwxp 00049000 00:02 23 /bin/busybox 77dc0000-77de2000 r-xp 00000000 00:02 273 /lib/libgcc_s.so.1 77de2000-77de3000 r-xp 00012000 00:02 273 /lib/libgcc_s.so.1 77de3000-77de4000 rwxp 00013000 00:02 273 /lib/libgcc_s.so.1 77de4000-77e7b000 r-xp 00000000 00:02 271 /lib/libc.so 77e8a000-77e8c000 rwxp 00096000 00:02 271 /lib/libc.so 77e8c000-77e8e000 rwxp 00000000 00:00 0 7fd86000-7fda7000 rw-p 00000000 00:00 0 [stack] 7fefd000-7fefe000 r-xp 00000000 00:00 0 7ffe6000-7ffe7000 r--p 00000000 00:00 0 [vvar] 7ffe7000-7ffe8000 r-xp 00000000 00:00 0 [vdso] root@OpenWrt:/# cat /proc/self/maps 00400000-00449000 r-xp 00000000 00:02 23 /bin/busybox 00458000-00459000 r-xp 00048000 00:02 23 /bin/busybox 00459000-0045a000 rwxp 00049000 00:02 23 /bin/busybox 77d55000-77d77000 r-xp 00000000 00:02 274 /lib/libgcc_s.so.1 77d77000-77d78000 r-xp 00012000 00:02 274 /lib/libgcc_s.so.1 77d78000-77d79000 rwxp 00013000 00:02 274 /lib/libgcc_s.so.1 77d79000-77e10000 r-xp 00000000 00:02 272 /lib/libc.so 77e1f000-77e21000 rwxp 00096000 00:02 272 /lib/libc.so 77e21000-77e23000 rwxp 00000000 00:00 0 7fe23000-7fe44000 rw-p 00000000 00:00 0 [stack] 7ff63000-7ff64000 r--p 00000000 00:00 0 [vvar] 7ff64000-7ff65000 r-xp 00000000 00:00 0 [vdso] Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Rosen Penev <rosenp@gmail.com> Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* tplink-safeloader: update soft_ver for TP-Link Archer C6 v2 (EU)Georgi Vlaev2020-03-301-1/+1
| | | | | | | | | | | | The last couple of TP-Link firmware releases for Archer C6 v2 (EU) have switched to version 1.2.x. Bump the soft_ver to "1.2.1" to allow firmware updates from the vendor web interface. TP-Link vendor firmware releases supported by this change: * Archer C6(EU)_V2_200110: soft_ver:1.2.1 Build 20200110 rel.60119 * Archer C6(EU)_V2_191014: soft_ver:1.2.0 Build 20191014 rel.33289 Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
* ath10k-ct: Support AQL on ath10k CT_KVER-5.4Jose Olivera2020-03-301-0/+10
| | | | | | | | | | | | | | | | | Commit ea50780 backported Airtime Queue Limits (AQL) from Linux 5.5 to OpenWrt's backports 5.4. However, this only enabled AQL for the vanilla ath10k driver. This patch also enables it for ath10k-ct. Tested on: * 2xTP-Link Archer A7v5 (QCA9563/QCA988X) * Backports version 5.4-rc8 & 5.4.27 * ath10k-ct and ath10k-ct-htt firmware version 014 to 017 * ath10k-ct driver versions dc025dc to 3d173a4 (CT_KVER-5.4) * WPA2, 802.11krv Tested since January 25, 2020. Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
* hostapd: add abridged flag in disassoc_imminentNick Hainke2020-03-301-0/+5
| | | | | | | | | | | | | If the abridged flag is set to 1 the APs that are listed in the BSS Transition Candidate List are prioritized. If the bit is not set, the APs have the same prioritization as the APs that are not in the list. If you want to steer a client, you should set the flag! The flag can be set by adding {...,'abridged': true,...} to the normal ubus call. Signed-off-by: Nick Hainke <vincent@systemli.org>
* hostapd: expose beacon reports through ubusNick Hainke2020-03-303-0/+51
| | | | | | | | | | | | | | | | | | | Subscribe to beacon reports through ubus. Can be used for hearing map and client steering purposes. First enable rrm: ubus call hostapd.wlan0 bss_mgmt_enable '{"beacon_report":True}' Subscribe to the hostapd notifications via ubus. Request beacon report: ubus call hostapd.wlan0 rrm_beacon_req '{"addr":"00:xx:xx:xx:xx:xx", "op_class":0, "channel":1, "duration":1,"mode":2,"bssid":"ff:ff:ff:ff:ff:ff", "ssid":""}' Signed-off-by: Nick Hainke <vincent@systemli.org> [rework identation] Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: Add 802.11r support for WPA3-EnterpriseJesus Fernandez Manzano2020-03-301-0/+1
| | | | Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.net>
* kernel: Enable CMOS RTC support on 5.4Kevin Darbyshire-Bryant2020-03-291-1/+1
| | | | | | | | | Enable kernel symbol CONFIG_RTC_DRV_CMOS which was enabled in 4.14 & 4.19 Fixes FS#2905 and now my APU2 picks up time from RTC Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: Deactivate NETGEAR WNCE2001 by defaultHauke Mehrtens2020-03-291-0/+1
| | | | | | | | | The root file system is getting too big for this device and this breaks the ramips/rt305x build. Do not build images for this board by default to fix this problem. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* odhcp6c: update to latest git HEADHans Dedecker2020-03-291-3/+3
| | | | | | f575351 ra: fix sending router solicitations Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* dnsmasq: bump to 2.81rc4Kevin Darbyshire-Bryant2020-03-291-2/+2
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* nftables: implement no/json variantsKevin Darbyshire-Bryant2020-03-291-14/+26
| | | | | | | | | | | Replace the build time choice of json support with a package based choice. Users requiring a json aware version of 'nft' may now install nftables-json. The default choice to fulfill the 'nftables' package dependency is 'nftables-nojson' Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* jansson: import jansson from packagesKevin Darbyshire-Bryant2020-03-291-0/+51
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* treewide: Don't diverge from upstream default HZ settings on 4.19Daniel Engberg2020-03-296-12/+4
| | | | | | | | | | | Most targets upstream use 250Hz or even 1000Hz by default while 100Hz is hardcoded in OpenWrt's default config. Use upstream default except for apm821xx which hardsets 1000Hz instead of platform default of 250Hz. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [Apply same changes to 5.4] Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* mac80211: Update to version 5.4.27Hauke Mehrtens2020-03-2938-654/+57
| | | | | | The removed patches are all integrated in the upstream version now. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Fix rt2x00 exportsHauke Mehrtens2020-03-292-17/+6
| | | | | | | | | | | | | | | | | | | Do not export static functions, they are anyway not referenced by any code in a different module. This fixes the following compile warning: WARNING: "rt2800_rf_aux_tx0_loopback" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL WARNING: "rt2800_write_dc" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL WARNING: "rt2800_rf_configstore" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL WARNING: "rt2800_do_sqrt_accumulation" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL WARNING: "rt2800_rf_configrecover" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL WARNING: "rt2800_loft_search" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL WARNING: "rt2800_iq_search" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL WARNING: "rt2800_setbbptonegenerator" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL WARNING: "rt2800_rf_aux_tx1_loopback" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL Acked-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: generic: 5.4: fix mtd concat panic on read/write functionsMichal Cieslakiewicz2020-03-291-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 2431c4f5b46c32c4ac495456b1ef4ce59c0bb85d ("mtd: Implement mtd_{read,write}() as wrappers around mtd_{read,write}_oob()") for kernel 5.4 restrict mtd devices to register only one type of read/write functions (either generic or OOB). mtd concat does not follow above rule and defines both methods at the same time, causing this type of device to be rejected by kernel. For routers that use mtd concat for root UBI volume that means kernel panic and boot loop with following error: [ 0.767307] Creating 1 MTD partitions on "ubi-concat": [ 0.772547] 0x000000000000-0x000007500000 : "ubi" [ 0.777953] ------------[ cut here ]------------ [ 0.782683] WARNING: CPU: 0 PID: 1 at drivers/mtd/mtdcore.c:621 add_mtd_device+0x84/0x5f4 [ 0.790983] Modules linked in: [ 0.794093] CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.24 #0 [ 0.799932] Stack : 80680000 8062af20 00000000 00000000 8062a0f0 87c2dae4 87c282fc 8065fd23 [ 0.808430] 805c64f4 00000001 807b32d8 80670000 80670000 00000001 87c2da98 25c15bcb [ 0.816909] 00000000 00000000 807e0000 0000006e 61696e74 00000000 2e342e32 34202330 [ 0.825397] 0000006e cef2ada7 00000000 000c1ded 00000000 00000009 00000000 8034de64 [ 0.833889] 00000009 80670000 80670000 80676d18 00000000 80320044 00000000 807b0000 [ 0.842381] ... [ 0.844861] Call Trace: [ 0.847367] [<80069994>] show_stack+0x30/0x100 [ 0.851913] [<8007e8ac>] __warn+0xc0/0x10c [ 0.856072] [<8007e954>] warn_slowpath_fmt+0x5c/0xac [ 0.861134] [<8034de64>] add_mtd_device+0x84/0x5f4 [ 0.866001] [<80352a50>] add_mtd_partitions+0xd8/0x1b8 [ 0.871231] [<803527b8>] parse_mtd_partitions+0x238/0x3f8 [ 0.876717] [<8034e51c>] mtd_device_parse_register+0x48/0x1b0 [ 0.882586] [<8038dd2c>] virt_concat_probe+0x170/0x1ec [ 0.887820] [<803334c8>] platform_drv_probe+0x40/0x94 [ 0.892970] [<80331638>] really_probe+0x104/0x35c [ 0.897766] [<80331d54>] device_driver_attach+0x70/0x98 [ 0.903072] [<80331ddc>] __driver_attach+0x60/0x100 [ 0.908042] [<8032f668>] bus_for_each_dev+0x68/0xa4 [ 0.912989] [<803309d4>] bus_add_driver+0x1f0/0x200 [ 0.917952] [<80332448>] driver_register+0x84/0x148 [ 0.922906] [<80060a1c>] do_one_initcall+0x7c/0x1dc [ 0.927870] [<80684e14>] kernel_init_freeable+0x158/0x23c [ 0.933361] [<805387d8>] kernel_init+0x10/0xf0 [ 0.937883] [<80064dd8>] ret_from_kernel_thread+0x14/0x1c [ 0.943375] ---[ end trace 62e0927fba490f68 ]--- [...] [ 2.266513] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 2.274893] Rebooting in 1 seconds.. This patch makes mtd concat to follow new mtd requirements by registering either normal or oob versions of read/write functions, but not both at the same time. OOB is used only when underlying mtd devices provide such functionality (like NAND chips) - otherwise generic methods are used. Tested successfully on Netgear WNDR4300. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* archs38: switch to kernel 5.4 by defaultEvgeniy Didin2020-03-291-1/+1
| | | | | | | | Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Petr Štetiar <ynezz@true.cz> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: John Crispin <john@phrozen.org>
* archs38: Add patch for gcc8 compilanceEvgeniy Didin2020-03-291-0/+21
| | | | | | | | | | | | Building Linux kernel version 5.4.x with GCC8 ends up with internal compiler error. The workaround on this issue can be introdution of additional compiler option "--mmpy-option=2" Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Petr Štetiar <ynezz@true.cz> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: John Crispin <john@phrozen.org>
* archs38: add kernel 5.4 configEvgeniy Didin2020-03-291-0/+285
| | | | | | | | | | | | Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Petr Štetiar <ynezz@true.cz> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: John Crispin <john@phrozen.org> [run make kernel_oldconfig CONFIG_TARGET=target] [Do not deactivate CONFIG_NET_VENDOR_*] [Activate CONFIG_HARDENED_USERCOPY] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: update arc-specific patchEvgeniy Didin2020-03-291-11/+11
| | | | | | | | | | | This patch updates arc-specific patch by moving declaration of struct object before it's usage. Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Petr Štetiar <ynezz@true.cz> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: John Crispin <john@phrozen.org>
* curl: rebuild when libopenssl config changesDENG Qingfang2020-03-291-1/+5
| | | | | | | | | | | | When some libopenssl options change curl will have to be rebuild to adapt to those changes, avoiding undefined reference errors or features disabled in curl. Add CONFIG_OPENSSL_ENGINE, CONFIG_OPENSSL_WITH_COMPRESSION and CONFIG_OPENSSL_WITH_NPN to PKG_CONFIG_DEPENDS so it will trigger rebuild every time the options are changed. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* mac80211: rtl8723bs: fix missing MMC dependencyPetr Štetiar2020-03-281-1/+1
| | | | | | | | | | | | Building of ath79-tiny has uncovered following: Package kmod-rtl8723bs is missing dependencies for the following libraries: mmc_core.ko So add this missing dependency. Fixes: 8c26d67a67d0 ("mac80211: realtek: add staging driver for RTL8723BS SDIO module") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mvebu: cortexa9: correct cpu subtypeTomasz Maciej Nowak2020-03-281-1/+1
| | | | | | | | | | | | | | | Armada 370 processors have only 16 double-precision registers. The change introduced by 8dcc1087602e ("toolchain: ARM: Fix toolchain compilation for gcc 8.x") switched accidentally the toolchain for mvebu cortexa9 subtarget to cpu type with 32 double-precision registers. This stems from gcc defaults which assume "vfpv3-d32" if only "vfpv3" as mfpu is specified. That change resulted in unusable image, in which kernel will kill userspace as soon as it causing "Illegal instruction". Ref: https://forum.openwrt.org/t/gcc-was-broken-on-mvebu-armada-370-device-after-commit-on-2019-03-25/43272 Fixes: 8dcc1087602e ("toolchain: ARM: Fix toolchain compilation for gcc 8.x") Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* tegra: correct cpu subtypeTomasz Maciej Nowak2020-03-281-1/+1
| | | | | | | | | | | | | | | Tegra 2 processors have only 16 double-precision registers. The change introduced by 8dcc1087602e ("toolchain: ARM: Fix toolchain compilation for gcc 8.x") switched accidentally the toolchain for tegra target to cpu type with 32 double-precision registers. This stems from gcc defaults which assume "vfpv3-d32" if only "vfpv3" as mfpu is specified. That change resulted in unusable image, in which kernel will kill userspace as soon as it causing "Illegal instruction". Ref: https://forum.openwrt.org/t/gcc-was-broken-on-mvebu-armada-370-device-after-commit-on-2019-03-25/43272 Fixes: 8dcc1087602e ("toolchain: ARM: Fix toolchain compilation for gcc 8.x") Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86: fix missing squashfs and ext4 rootfs imagesPaul Spooren2020-03-281-2/+4
| | | | | | | | | | | | | | | The previous rework of x86 image creation done in commit cb007a7bf619 ("x86: switch image generation to new code") removed images of separate squashfs and ext4 filesystems which are handy for example in testing under QEMU. So this patch adds back creation of those missing rootfs images for ext4 and squashfs based filesystems. Fixes: cb007a7bf619 ("x86: switch image generation to new code") Signed-off-by: Paul Spooren <mail@aparcar.org> [commit subject and description tweaks] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* x86: fix padding in imagesPaul Spooren2020-03-281-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The previous rework of x86 image creation done in commit cb007a7bf619 ("x86: switch image generation to new code") broke the padding in images. sda: p2 size 212992 extends beyond EOD, enabling native capacity sda: p2 size 212992 extends beyond EOD, truncated sd 0:0:0:0: [sda] Attached SCSI disk SQUASHFS error: squashfs_read_data failed to read block 0x2cc556 unable to read id index table VFS: Cannot open root device "PARTUUID=ac5c9cd8-02" or unknown-block(8,2): error -5 Please append a correct "root=" boot option; here are the available partitions: 0800 19761 sda driver: sd 0801 16384 sda1 ac5c9cd8-01 0802 2865 sda2 ac5c9cd8-02 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,2) Tested with x86/64 with Docker (squashfs), qemustart (ext4/squashfs) and virtualbox (ext4/squashfs). Ref: FS#2935 Fixes: cb007a7bf619 ("x86: switch image generation to new code") Suggested-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Paul Spooren <mail@aparcar.org> [commit subject and description tweaks] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: package gpio-f7188x driverNick Bowler2020-03-281-0/+16
| | | | | | | This driver enables support for the GPIO capabilities found in many Fintek Super-IO chips. Signed-off-by: Nick Bowler <nbowler@draconx.ca>
* kernel: package f71808e-wdt driverNick Bowler2020-03-281-0/+16
| | | | | | | This driver enables support for the watchdog timers found in many Fintek Super-IO chips. Signed-off-by: Nick Bowler <nbowler@draconx.ca>
* kernel: package f71882fg hwmon driverNick Bowler2020-03-281-0/+15
| | | | | | | This driver enables hardware monitoring support using the sensors found in many Fintek Super-IO chips. Signed-off-by: Nick Bowler <nbowler@draconx.ca>
* openssl: revert EOF detection change in 1.1.1Eneas U de Queiroz2020-03-282-1/+81
| | | | | | | | | | | | | | | | | | | | | | This adds patches to avoid possible application breakage caused by a change in behavior introduced in 1.1.1e. It affects at least nginx, which logs error messages such as: nginx[16652]: [crit] 16675#0: *358 SSL_read() failed (SSL: error: 4095126:SSL routines:ssl3_read_n:unexpected eof while reading) while keepalive, client: xxxx, server: [::]:443 Openssl commits db943f4 (Detect EOF while reading in libssl), and 22623e0 (Teach more BIOs how to handle BIO_CTRL_EOF) changed the behavior when encountering an EOF in SSL_read(). Previous behavior was to return SSL_ERROR_SYSCALL, but errno would still be 0. The commits being reverted changed it to SSL_ERRO_SSL, and add an error to the stack, which is correct. Unfortunately this affects a number of applications that counted on the old behavior, including nginx. The reversion was discussed in openssl/openssl#11378, and implemented as PR openssl/openssl#11400. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* ar71xx: Fix gigabit switch support for Mikrotik RB951G-2HnDBaptiste Jonglez2020-03-281-0/+2
| | | | | | | | | | | | | | | | | | | | Without this patch, when using rev 3 of the Atheros AR9344 SoC, the gigabit switch (AR8327) does not work or works very erratically. This is a re-spin of http://patchwork.ozlabs.org/patch/419857/ with a different PLL value, according to the feedback from several users (including myself) as shown here: https://openwrt.org/toh/mikrotik/rb2011uias#tracking_reported_experience_with_suggested_patch_for_the_5_gige_ports Performance is acceptable: testing L3 forwarding without NAT yields a performance of 370 Mbit/s (iperf3 TCP) and 41 Kpps (iperf3 UDP with 64 bytes payload). Both tests show that 100% of CPU time is spent on softirq. A similar fix for a different device (RB2011) was added in e457d22261 ("Make GBit switch work on RB2011"). Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
* kernel: bump 5.4 to 5.4.28Petr Štetiar2020-03-2852-600/+112
| | | | | | | | | | | | | | | | | | | | Changelog since 5.4.24 mentions CVE-2019-19769, CVE-2020-8648, CVE-2020-8649 and CVE-2020-8647. Removed upstreamed: generic: 507-v5.6-iio-chemical-sps30-fix-missing-triggered-buffer-depe.patch generic: 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch bcm27xx: 950-0435-ASoC-pcm512x-Fix-unbalanced-regulator-enable-call-in.patch ipq806x: 701-stmmac-fix-notifier-registration.patch lantiq: 002-pinctrl-falcon-fix-syntax-error.patch octeontx: 0002-net-thunderx-workaround-BGX-TX-Underflow-issue.patch Run tested: apu2, qemu-x86-64, apalis, a64-olinuxino, nbg6617 Build tested: sunxi/a53, imx6, x86/64, ipq40xx Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [apu2] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: switch to 5.4 kernelPetr Štetiar2020-03-281-1/+1
| | | | | | | 5.4.24 seems to be working fine on my zyxel,nbg6617, so let's start wider userbase testing. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: wpj428: fix missing MDIO GPIO reset and pinmuxLeon M. George2020-03-282-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | The bootloader does not always initialize the MDIO pins before booting Linux. E.g. on version "U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jul 25 2017 - 11:36:26)" this is the case when booting automatically without activating the U-Boot console. Without this change, the kernel boot will complain about missing PHYs: libphy: ipq40xx_mdio: probed ar40xx c000000.ess-switch: Probe failed - Missing PHYs! libphy: Fixed MDIO Bus: probed With this change it will work as expected: libphy: ipq40xx_mdio: probed ESS reset ok! ESS reset ok! libphy: Fixed MDIO Bus: probed Ref: GH-2835 Tested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> Signed-off-by: Leon M. George <leon@georgemail.eu> [commit description from Fredrik, subject facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: switch to 5.4 kernelPetr Štetiar2020-03-281-1/+1
| | | | | | | Seems to be working fine on my a64-olinuxino, it's 99.9% upstream stuff anyway. Lets start wider userbase testing. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: a53: fix ethernet on a64-olinuxinoPetr Štetiar2020-03-281-0/+1
| | | | | | | a64-olinuxino board has Micrel KSZ9031 Gigabit PHY so add support for this PHY into kernel. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: 5.4: dts: a64: olinuxino: add bank supply regulatorsPetr Štetiar2020-03-281-0/+62
| | | | | | | | | | | | | | This is backport of v5.6 patch. Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL. This patch adds regulators for them to the pinctrl node. Exception is PL which is used by the RSB bus. To avoid circular dependencies, VCC-PL is omitted. On boards with eMMC, VCC-PC is supplied by ELDO1, instead of DCDC1. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: 5.4: a64-olinuxino: use red LED for status signalizationPetr Štetiar2020-03-282-0/+68
| | | | | | | There is a red LED marked as `GPIO_LED1` on the silkscreen and connected to PE17, so use this LED for status signalization. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: a53: add support for Olimex A64-Olinuxino eMMCPetr Štetiar2020-03-281-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit) RAM: 1GB or 2GB RAM DDR3L @ 672Mhz Flash: 0/4/16GB eMMC flash memory for storage and boot MicroSD card connector for cards up to 32GB Debug: serial UART debug header with 0.1" pins Wired connectivity: 10/100/1000Mbps GbE Ethernet Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and Bluetooth 4.0 module with built-in antenna (only available in the A64-OLinuXino-1G4GW) Flashing instructions: Standard sunxi SD card installation procedure - copy eMMC image to SD card, insert in into SD card slot on the device and boot. You should see something like following if the eMMC is detected correctly: mmcblk2: mmc2:0001 P1XXXX 3.60 GiB mmcblk2boot0: mmc2:0001 P1XXXX partition 1 16.0 MiB mmcblk2boot1: mmc2:0001 P1XXXX partition 2 16.0 MiB Then flash SD card eMMC image straight into the mmcblk2 device: dd if=/mnt/openwrt...a64-olinuxino-emmc-squashfs-sdcard.img of=/dev/mmcblk2 It also possible to boot from boot0 partition[1]: 1. Compile U-Boot with CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x40 otherwise the U-Boot will get stuck in bootloop 2. Configure eMMC to boot from boot0 partition inside U-Boot: mmc bootbus 1 1 0 0; mmc partconf 1 1 1 0 3. echo 0 > /sys/block/mmcblk2boot0/force_ro 4. Write U-Boot from offset 0 (not offset 8k as with SD card) into boot0 partition dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk2boot0 Known issues: Wireless doesn't work properly via netifd. 1. https://linux-sunxi.org/index.php?title=Bootable_eMMC Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 05:40:38 +0000