aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* realtek: make Netgear GS1xx u-boot env partition writableStijn Segers2022-06-221-1/+0
| | | | | | | | | | | Make the u-boot environment partition for the NETGEAR GS108T v3 and GS110TPP writable (they share a DTS), so the values can be manipulated from userspace. See https://forum.openwrt.org/t/57875/1567 for a real world example. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* ath79: support for TP-Link EAP225-Outdoor v3Paul Maruhn2022-06-223-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This model is almost identical to the EAP225-Outdoor v1. Major difference is the RTL8211FS PHY Chipset. Device specifications: * SoC: QCA9563 @ 775MHz * Memory: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n 2x2 * Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO * Ethernet (RTL8211FS): 1× 1GbE, PoE Flashing instructions: * ssh into target device with recent (>= v1.6.0) firmware * run `cliclientd stopcs` on target device * upload factory image via web interface Debricking: To recover the device, you need access to the serial port. This requires fine soldering to test points, or the use of probe pins. * Open the case and solder wires to the test points: RXD, TXD and TPGND4 * Use a 3.3V UART, 115200 baud, 8n1 * Interrupt bootloader by holding ctrl+B during boot * upload initramfs via built-in tftp client and perform sysupgrade setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From stock ifconfig: ath0 Link encap:Ethernet HWaddr D8:...:2E ath10 Link encap:Ethernet HWaddr D8:...:2F br0 Link encap:Ethernet HWaddr D8:...:2E eth0 Link encap:Ethernet HWaddr D8:...:2E Signed-off-by: Paul Maruhn <paulmaruhn@posteo.de> Co-developed-by: Philipp Rothmann <philipprothmann@posteo.de> Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de> [Add pre-calibraton nvme-cells] Tested-by: Tido Klaassen <tido_ff@4gh.eu> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: generic: add support for Realtek PHYPhilipp Rothmann2022-06-221-0/+1
| | | | | | | Some models of the TP-Link EAP225 series use a Realtek PHY, therefore the driver is added. Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de>
* mt76: update to the latest versionFelix Fietkau2022-06-211-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 4554ee652caf mt76: mt7921: fix warning Using plain integer as NULL pointer a3f1d6ccf3ca mt76: mt7921: add missing bh-disable around rx napi schedule 9aeca2a5ce47 mt76: mt7921: get rid of mt7921_mcu_exit fee8a5911c76 mt76: connac: move shared fw structures in connac module db4d784ae7ba mt76: mt7921: move fw toggle in mt7921_load_firmware 16ab6bf49556 mt76: connac: move mt76_connac2_load_ram in connac module 29fd748801c6 mt76: connac: move mt76_connac2_load_patch in connac module 051c68d18214 mt76: mt7663: rely on mt76_connac2_fw_trailer d6ae3505ac6c mt76: enable the VHT extended NSS BW feature 488a5ccc9762 mt76: mt7921: rely on mt76_dev in mt7921_mac_write_txwi signature 934029bb93e2 mt76: mt7915: rely on mt76_dev in mt7915_mac_write_txwi signature ecefae4c7d72 mt76: connac: move mac connac2 defs in mt76_connac2_mac.h b5eecc841df8 mt76: connac: move connac2_mac_write_txwi in mt76_connac module 012e619a07b9 mt76: connac: move mt76_connac2_mac_add_txs_skb in connac module 1b492be795ea mt76: mt7921: not support beacon offload disable command f1f46d3b4b19 mt76: mt7921: fix command timeout in AP stop period cae61112ef1d mt76: connac: move HE radiotap parsing in connac module 487674062643 mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module 649bdc4983c4 mt76: connac: move mt76_connac2_mac_fill_rx_rate in connac module cb75aaa39252 mt76: mt7921s: remove unnecessary goto in mt7921s_mcu_drv_pmctrl e0eaf66eaebb mt76: mt7615: do not update pm stats in case of error f8d125b4ea30 mt76: mt7921: do not update pm states in case of error 6329a834907e mt76: mt7921s: fix possible sdio deadlock in command fail 8a04f1b04662 mt76: mt7921: fix aggregation subframes setting to HE max e52283439094 mt76: mt7915: disable UL MU-MIMO for mt7915 fd3958970e3d mt76: mt7921: enlarge maximum VHT MPDU length to 11454 18df38fe77f7 mt76: mt7915: get rid of unnecessary new line in mt7915_mac_write_txwi 149e95f5d7a6 mt76: connac: move mt76_connac_fw_txp in common module 899d192e8a79 mt76: move mt7615_txp_ptr in mt76_connac module 7184f0a6f6a5 mt76: connac: move mt76_connac_tx_free in shared code c42d45278fa5 mt76: connac: move mt76_connac_tx_complete_skb in shared code 0993f4ef96f8 mt76: connac: move mt76_connac_write_hw_txp in shared code 467960fab791 mt76: connac: move mt7615_txp_skb_unmap in common code 2e758064b085 mt76: mt7915: rely on mt76_connac_tx_free 2065a7901671 mt76: move mcu_txd/mcu_rxd structures in shared code 576c1b7c472b mt76: move mt76_connac2_mcu_fill_message in mt76_connac module 7275f7758090 mt76: mt7915: fix incorrect testmode ipg on band 1 caused by wmm_idx Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: filter -no-plt from KCFLAGSKevin Darbyshire-Bryant2022-06-212-2/+1
| | | | | | | | | | | | Compiler option -no-plt will break kernel builds on some architectures eg. (x86) Filter this option from the recently introduced handling of KCFLAGS vs EXTRA_OPTIMISATION Fixes: 1d42af720c6b ("kernel: use KCFLAGS for passing EXTRA_OPTIMIZATION flags") Suggested-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* hostapd: document ubus methodsStijn Tintel2022-06-211-0/+416
| | | | | | | Document the ubus methods we added to hostapd so that people don't have to read code to figure out which methods are available and what they do. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* bcm47xx: Fix Netgear WNR3500L v2 image formatFlorian Fainelli2022-06-201-0/+2
| | | | | | | | CFE on these devices expects to find the kernel compressed with LZMA but with no dictionnary and no loader, adjust the image generation accordingly. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* bcm47xx: Updated devices database for Netgear WNR3500L V2Florian Fainelli2022-06-202-50/+144
| | | | | | | Update the device databases to contain an entry for the Netgear WNR3500L v2 router, the same buttons and LEDs mapping as v1 is used. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* bcm47xx: Add support for brcmnand controller on BCMA busFlorian Fainelli2022-06-2010-1/+862
| | | | | | | | Back port the patches being submitted upstream in order to make the NAND controller work on BCM47187/5358. This is a prerequisite for supporting devices like the Netgear WNR3500L V2. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* broadcom-wl: Fix compilation with kernel 5.10Florian Fainelli2022-06-204-8/+50
| | | | | | | | | | | | | This adds a few fixes for compiling against Linux 5.10: 1. segment_eq() has been removed with upstream commit 428e2976a5bf7e7f5554286d7a5a33b8147b106a ("uaccess: remove segment_eq") and can use uaccess_kernel() instead 2. ioremap_nocache() is removed and is now an alias for ioremap() with upstream commit 4bdc0d676a643140bdf17dbf7eafedee3d496a3c ("remove ioremap_nocache and devm_ioremap_nocache") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* kernel: drop patch adding hardcoded kernel compilation flagsRafał Miłecki2022-06-202-50/+0
| | | | | | | | | | | | | | | | | | | 1. KCFLAGS should be used for custom flags 2. Optimization flags are arch / SoC specific 3. -fno-reorder-blocks may *worsen* network performace on some SoCs 4. Usage of flags was *reversed* since 5.4 and noone reported that If we really need custom flags then CONFIG_KERNEL_CFLAGS should get default value adjusted properly (per target). Ref: 4e0c54bc5bc8 ("kernel: add support for kernel 5.4") Link: http://lists.openwrt.org/pipermail/openwrt-devel/2022-June/038853.html Link: https://patchwork.ozlabs.org/project/openwrt/patch/20190409093046.13401-1-zajec5@gmail.com/ Cc: Felix Fietkau <nbd@nbd.name> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: Rui Salvaterra <rsalvaterra@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: support setting extra CFLAGS for kernel compilationRafał Miłecki2022-06-202-1/+5
| | | | | | They may be used e.g. to optimize kernel size or performance. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* lantiq: dts: fix reset controller reference on Danube and AR9Martin Blumenstingl2022-06-202-2/+2
| | | | | | | | | | | ar9.dtsi and danube.dtsi only have one reset controller and they are naming it "reset". This is equivalent to "reset0" in vr9.dtsi. Fix the references to the reset controller in the recently added PCI controller reset line. Fixes: 087f2cba26faf0 ("lantiq: dts: Add the reset line for the PCI controller") Reported-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ramips: fix booting on ZyXEL NBG-419N v2Piotr Dymacz2022-06-201-0/+1
| | | | | | | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of other devices from 'ramips' target. Fixes: #9842 Fixes: #8964 Reported-by: Juergen Hench <jurgen.hench@gmail.com> Tested-by: Juergen Hench <jurgen.hench@gmail.com> Signed-off-by: Demetris Ierokipides <ierokipides.dem@gmail.com> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: use KCFLAGS for passing EXTRA_OPTIMIZATION flagsRafał Miłecki2022-06-193-19/+7
| | | | | | | This uses kernel's generic variable and doesn't require patching it with a custom Makefile change. It's expected *not* to change any behaviour. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport mtd parser for Sercomm partitionsRafał Miłecki2022-06-197-16/+621
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* 464xlat: delete SNATed conntracks on interface teardownAlin Nastac2022-06-192-1/+4
| | | | | | | | | Existing conntracks will continue to be SNATed to 192.0.0.1 even after 464xlat interface gets teared down. To prevent this, matching conntracks must be killed. Signed-off-by: Alin Nastac <alin.nastac@gmail.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
* mvebu: add SolidRun ClearFog GT 8KLogan Blyth2022-06-193-3/+20
| | | | | | | | ClearFog GT 8K is device sold by SolidRun. It is marketed as a development board, not a consumer product. The device tree file for this board is upstream in kernel.org. Signed-off-by: Logan Blyth <mrbojangles3@gmail.com>
* apm821xx: align gpio-keys node names with dt-schemaChristian Lamparter2022-06-195-8/+8
| | | | | | | | | | | | As per the series: <https://www.spinics.net/lists/devicetree/msg508906.html> "Enforce specific naming pattern for children (keys) to narrow the pattern thus do not match other properties. This will require all children to be properly prefixed or suffixed (button, event, switch or key)." Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* failsafe: run on all consoles listed in /proc/cmdlineMark Mentovai2022-06-192-35/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On x86, when both CONFIG_GRUB_CONSOLE and CONFIG_GRUB_SERIAL are set (as they are by default), the kernel command line will have two console= entries, such as console=tty0 console=ttyS0,115200n8 Failsafe was only running a shell on the first defined console, the VGA console. This is a problem for devices like apu2, where there is only a serial console and it appears on ttyS0. Moreover, the console prompt to enter failsafe during boot was delivered to, and its input read from, the last console= on the kernel command line. So while the failsafe shell was on the first defined console, only the last defined console could be used to enter failsafe during boot. In contrast, the x86 bootloader (GRUB) operates on both the serial console and the VGA console by virtue of "terminal_{input,output} console serial". GRUB also provided an alternate means to enter failsafe from either console. The presence of two console= kernel command line parameters causes kernel messages to be delivered to both. Under normal operation (not failsafe), procd runs login in accordance with inittab, which on x86 specifies ttyS0, hvc0, and tty1, allowing login through any of serial, hypervisor, or VGA console. Thus, serial access was consistently available on x86 devices with serial consoles under normal operation, except for shell access in failsafe mode (without editing the kernel command line). By presenting the failsafe prompt, reading failsafe prompt input, and running failsafe shells on all consoles listed in /proc/cmdline, failsafe mode will work correctly on devices with a serial console (like apu2), and the same image without any need for reconfiguration can be shared by devices with the more traditional (for x86) VGA console. This improvement should benefit any system with multiple console= arguments, including x86 and bcm27xx (Raspberry Pi). Signed-off-by: Mark Mentovai <mark at moxienet.com>
* libusb: fix missing linkLeo Soares2022-06-191-1/+1
| | | | | | | | | adds `libusb-1.0.so` link on the target root again. Fixes: 43539a6aabbe ("libusb: make InstallDev explicit") Signed-off-by: Leo Soares <leo@hyper.ag> (added fixed tag, reworded commit) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* lantiq: dts: Add the reset line for the PCI controllerMartin Blumenstingl2022-06-193-0/+6
| | | | | | | The PCI controller has it's reset line wired up to bit 13 of RCU. Describe this in our .dtsi files. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ath10k: backport encapsulation offload supportZhijun You2022-06-1911-20/+520
| | | | | | | | This backports encap offload support from upstream. On some ath10k devices there can be about 10% improvement on tx throughput. Users can turn it on by setting frame_mode=2. Signed-off-by: Zhijun You <hujy652@gmail.com>
* ath79: add support for Netgear PGZNG1Chris Blake2022-06-196-0/+379
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear PGZNG1, also known as the ADT Pulse Gateway. Hardware: CPU: Atheros AR9344 Memory: 256MB Storage: 256MB NAND Hynix H27U2G8F2CTR-BC USB: 1x USB 2.0 Ethernet: 2x 100Mb/s WiFi: Atheros AR9340 2.4GHz 2T2R Leds: 8 LEDs Button: 1x Reset Button UART: Header marked JPE1. Pinout is VCC, TX, RX, GND. The marked pin, closest to the JPE1 marking, is VCC. Note VCC isn't required to be connected for UART to work. Enable Stock Firmware Shell Access: 1. Interrupt u-boot and run the following commands setenv console_mode 1 saveenv reset This will enable a UART shell in the firmware. You can then login using the root password of `icontrol`. If that doesn't work, the device is running a firmware based on OpenWRT where you can drop into failsafe to mount the FS and then modify /etc/passwd. Installation Instructions: 1. Interupt u-boot and run the following commands setenv active_image 0 setenv stock_bootcmd nboot 0x81000000 0 \${kernel_offset} setenv openwrt_bootcmd nboot 0x82000000 0 \${kernel_offset} setenv bootcmd run openwrt_bootcmd saveenv 2. boot initramfs image via TFTP u-boot tftpboot 0x82000000 openwrt-ath79-nand-netgear_pgzng1-initramfs-kernel.bin; bootm 0x82000000 3. Once booted, use LuCI sysupgrade to flash openwrt-ath79-nand-netgear_pgzng1-squashfs-sysupgrade.bin MAC Table: WAN (eth0): xx:xa - caldata 0x0 LAN (eth1): xx:xb - caldata 0x6 WLAN (phy0): xx:xc - burned into ath9k caldata Not Working: Z-Wave RS422 Signed-off-by: Chris Blake <chrisrblake93@gmail.com> (added more hw-info, fixed file permissions) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: add kmod-leds-pca955xChris Blake2022-06-191-0/+19
| | | | | | | | | This patch adds support for the mainline kernel module for the PCA955x LED driver. Note this requires i2c and GPIO support. Also worth calling out this driver also enables GPIO support, depending on device tree configuration. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* kernel: add upstream patches for pca955x led driverChris Blake2022-06-195-0/+582
| | | | | | | | These patches are to support the pca955x led with OpenWRT correctly via device tree on linux 5.10. Without these, the new LED function/color/reg features can not be used. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* uboot-rockchip: drop CONFIG_IDENT_STRINGJosef Schlehofer2022-06-191-1/+0
| | | | | | | | | | This row is no longer necessary as it was replaced by LOCALVERSION in uboot.mk, which explicitly sets OpenWrt version to all U-boot packages accross OpenWrt. [1] [1] https://github.com/openwrt/openwrt/commit/d6aa9d9e071d9f23ed26f5142991bc66aefe20f5 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* tools/libressl: update to version 3.4.3Josef Schlehofer2022-06-191-2/+2
| | | | | | | | | | | | | | Release notes: https://ftp.openbsd.org/pub/OpenBSD/LibreSSL/libressl-3.4.3-relnotes.txt ``` It includes the following security fix: * A malicious certificate can cause an infinite loop. Reported by and fix from Tavis Ormandy and David Benjamin, Google. ``` Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* mpc85xx: p2020: add RTC ds1307 to kernelJosef Schlehofer2022-06-191-0/+1
| | | | | | | | | | | | | | If the RTC module is compiled as a module, the hctosys fails to initialize because ds1307 is loaded later. Fixes: [ 2.004145] hctosys: unable to open rtc device (rtc0) [ 11.957997] rtc-ds1307 0-006f: registered as rtc0 This is similar to commit 5481ce9a1157a43d8b2c963e03fb243e70974361, which was done for imx6 target. Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* ipq40xx: add support for Meraki MR74Matthew Hagan2022-06-1911-409/+452
| | | | | | | | | | | | The Meraki MR74 is part of the "Insect" series. This device is essentially an outdoor variant of the MR33 with identical hardware, but requiring a config@3 DTS option to be set to allow booting with the stock u-boot. The install procedure is replicated from the MR33, with the exception being that the MR74 sysupgrade image must be used. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* apm821xx: MBL: make mtd chip workChristian Lamparter2022-06-194-2/+11
| | | | | | | | | | | | | | | | The MBL has a 512KiB Microchip SST39VF040 chip for uboot and not much else. Thanks to Ewald who figured out that the "jedec-probe" vs. "jedec-flash" was the wrong binding. With this information and the jedec-probe support enabled => the chip works. | physmap-flash 4fff80000.nor_flash: physmap platform flash device: [mem 0x4fff80000-0x4ffffffff] | Found: SST 39LF040 | 4fff80000.nor_flash: Found 1 x8 devices at 0x0 in 8-bit bank Suggested-by: Ewald Comhaire <e.comhaire@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: enable NAND support for all subtargetsJosef Schlehofer2022-06-193-3/+1
| | | | | | | | | | | | | | In subtarget p2020, there wasn't enabled nand support, and because of that there weren't available tools from mtd-utils package, which has utilities for NAND flash memory even though reference board, which is the only currently supported device in p2020 subtarget has NAND [1]. All subtargets in mpc85xx has already enabled nand support, let's do it globally. [1] https://www.nxp.com/design/qoriq-developer-resources/p2020-reference-design-board:P2020RDB Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* kernel: Backport mv88e6xxx patch to keep pvid at 0 if VLAN-unaware and ↵Marek Behún2022-06-191-18/+0
| | | | | | | | | | | | | | | remove hack Keeping the pvid at 0 when VLAN-unaware makes it possible to drop the hack introduced in commit 920eaab1d817 ("kernel: DSA roaming fix for Marvell mv88e6xxx"). Dropping the hack makes it possible to use VLAN interfaces with VID 1 on DSA ports without problems with FDB. Signed-off-by: Marek Behún <kabel@kernel.org> (cherry picked from commit 9caa6f0aa742253901c72f43eebecd2c8da5f127) Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [drop kernel patch hack from Linux version 5.15, drop paragraph about backport patch, which is not necessary as it is included in kernel 5.15]
* bcm53xx: remove 07_set_preinit_iface_bcm53xxChristian Lamparter2022-06-191-14/+0
| | | | | | | | with the switch to DSA setup, the switch gets correctly programmed via the device-tree now. This hack is no longer necessary. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: move Toshiba-TC58NVG0S3H patch to ipq40xx reduxChristian Lamparter2022-06-192-12/+6
| | | | | | | | | | | | | | | | | | Linux' upstream MTD-Maintainer Miquèl Raynal noted: |Reverting seems the safest option here, not knowing how many devices |have these damaged/counterfeit chips. If it is just a couple and only on |Fritzboxes, as suggested in the Github issue this patch could be |carried through OpenWrt and that would seem more future proof IMHO. This patch follows up with the first patch. It actually moves the patches out of target/linux/generic/pending into the ipq40xx's patch heap and adds a little note what happend. For more information, discussions or reports about bad TC58NVG0S3Hs, please visit the OpenWrt's Github Issue #9962: <https://github.com/openwrt/openwrt/issues/9962> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* netfilter: kmod-nft-xfrmFlorian Eckert2022-06-192-0/+13
| | | | | | Add kmod-nft-xfrm package. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* realtek: add support for power LED on Netgear GS108Tv3Pascal Ernster2022-06-191-0/+27
| | | | | | | | | | | | | | | | | | | | | The Netgear GS108Tv3 is already supported by OpenWrt, but is missing LED support. After OpenWrt installation, all LEDs are off which makes the installation quite confusing. This enables support for the green/amber power LED to give feedback about the current status. This is basically just a verbatim copy of commit c4927747d25a ("realtek: add support for power LED on Netgear GS308Tv1"). Please note that both LEDs are wired up in an anti-parallel fashion, which means that only one of both LEDs/colors can be switched on at the same time. If both LEDs/colors are switched on simultanously, the LED goes dark. Tested-by: Pascal Ernster <git@hardfalcon.net> Signed-off-by: Pascal Ernster <git@hardfalcon.net> [add title to commit reference] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: add support for D-Link DGS-1210-20Markus Stockhausen2022-06-193-0/+111
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification ---------------------- * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DRAM * 32MB NOR Flash * 16 x 10/100/1000BASE-T ports - Internal PHY with 8 ports (RTL8218B) - External PHY with 8 ports (RTL8218B) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6 UART pinout ----------- [o]ooo|J6 | ||`------ GND | |`------- RX | `-------- TX `---------- Vcc (3V3) Boot initramfs image from U-Boot -------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl838x-d-link_dgs-1210-20-initramfs-kernel.bin` command 5. Boot the image with `bootm` command To install, upload the sysupgrade image to the OEM webpage or sysupgrade from the system running from initramfs image. It has been developed and tested on device with F1 revision. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> [correct initramfs image name] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* rockchip: add kernel 5.15 as testingJuergen Wurzer2022-06-186-1/+763
| | | | | | | | Add kernel 5.15 as testing kernel for the rockchip-armv8 target. Signed-off-by: Juergen Wurzer <wurzer.juergen@gmail.com> [squash commits, update commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix RT-AC57U button levelDavid Bauer2022-06-181-1/+1
| | | | | | | Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the WPS cutton to fix button behavior. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: update to 2022-06-02David Bauer2022-06-182-3/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 4383528e0 P2P: Use weighted preferred channel list for channel selection f2c5c8d38 QCA vendor attribute to configure RX link speed threshold for roaming 94bc94b20 Add QCA vendor attribute for DO_ACS to allow using existing scan entries b9e2826b9 P2P: Filter 6 GHz channels if peer doesn't support them d5a9944b8 Reserve QCA vendor sub command id 206..212 ed63c286f Remove space before tab in QCA vendor commands e4015440a ProxyARP: Clear bridge parameters on deinit only if hostapd set them 02047e9c8 hs20-osu-client: Explicit checks for snprintf() result cd92f7f98 FIPS PRF: Avoid duplicate SHA1Init() functionality 5c87fcc15 OpenSSL: Use internal FIPS 186-2 PRF with OpenSSL 3.0 9e305878c SAE-PK: Fix build without AES-SIV c41004d86 OpenSSL: Convert more crypto_ec_key routines to new EVP API 667a2959c OpenSSL: crypto_ec_key_get_public_key() using new EVP_PKEY API 5b97395b3 OpenSSL: crypto_ec_key_get_private_key() using new EVP_PKEY API 177ebfe10 crypto: Convert crypto_ec_key_get_public_key() to return new ec_point 26780d92f crypto: Convert crypto_ec_key_get_private_key() to return new bignum c9c2c2d9c OpenSSL: Fix a memory leak on crypto_hash_init() error path 6d19dccf9 OpenSSL: Free OSSL_DECODER_CTX in tls_global_dh() 4f4479ef9 OpenSSL: crypto_ec_key_parse_{priv,pub}() without EC_KEY API b092d8ee6 tests: imsi_privacy_attr 563699174 EAP-SIM/AKA peer: IMSI privacy attribute 1004fb7ee tests: Testing functionality to discard DPP Public Action frames 355069616 tests: Add forgotten files for expired IMSI privacy cert tests b9a222cdd tests: sigma_dut and DPP curve-from-URI special functionality fa36e7ee4 tests: sigma_dut controlled STA and EAP-AKA parameters 99165cc4b Rename wpa_supplicant imsi_privacy_key configuration parameter dde7f90a4 tests: Update VM setup example to use Ubuntu 22.04 and UML 426932f06 tests: EAP-AKA and expired imsi_privacy_key 35eda6e70 EAP-SIM peer: Free imsi_privacy_key on an error path 1328cdeb1 Do not try to use network profile with invalid imsi_privacy_key d1652dc7c OpenSSL: Refuse to accept expired RSA certificate 866e7b745 OpenSSL: Include rsa.h for OpenSSL 3.0 bc99366f9 OpenSSL: Drop security level to 0 with OpenSSL 3.0 when using TLS 1.0/1.1 39e662308 tests: Work around reentrant logging issues due to __del__ misuse 72641f924 tests: Clean up failed test list in parallel-vm.py e36a7c794 tests: Support pycryptodome a44744d3b tests: Set ECB mode for AES explicitly to work with cryptodome e90ea900a tests: sigma_dut DPP TCP Configurator as initiator with addr from URI ed325ff0f DPP: Allow TCP destination (address/port) to be used from peer URI e58dabbcf tests: DPP URI with host info 37bb4178b DPP: Host information in bootstrapping URI 1142b6e41 EHT: Do not check HE PHY capability info reserved fields 7173992b9 tests: Flush scan table in ap_wps_priority to make it more robust b9313e17e tests: Update ap_wpa2_psk_ext_delayed_ptk_rekey to match implementation bc3699179 Use Secure=1 in PTK rekeying EAPOL-Key msg 1/4 and 2/4 d2ce1b4d6 tests: Wait for request before responding in dscp_response Compile-tested: all versions / ath79-generic, ramips-mt7621 Run-tested: hostapd-wolfssl / ath79-generic, ramips-mt7621 Signed-off-by: David Bauer <mail@david-bauer.net>
* base-files: allow ignoring minor compat-version checkDavid Bauer2022-06-182-0/+5
| | | | | | | | | | | | Downstream projects might re-generate device-specific configuration based on OpenWrt's defaults on each upgrade, thus being unaffected by forward- as well as backwards-breaking configuration. Add a new sysupgrade parameter, which allows sysupgrades between minor compat-versions. Upgrades will still fail upon mismatching major compat versions. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: TP-Link EAP225 v3: use pre-calibration nvmem-cellSander Vanheule2022-06-181-3/+3
| | | | | | | | | ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Rename the nvmem cell node and label to match the updated cell name. Fixes: eca0d7301198 ("ath79: TP-Link EAP225 v3: convert ath10k to nvmem-cells") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225-Wall v2: use pre-calibration nvmem-cellSander Vanheule2022-06-181-3/+3
| | | | | | | | | ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Rename the nvmem cell node and label to match the updated cell name. Fixes: 48625a04453b ("ath79: TP-Link EAP225-Wall v1: convert radios to nvmem-cells") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225-Outdoor v1: use pre-calibration nvmem-cellNick Hainke2022-06-181-3/+3
| | | | | | | | | | | | | | | | | | | | | | Fixes errors in the form of: ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci, vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device =0000 from ath10k/QCA9888/hw2.0/board-2.bin ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0 ath10k_pci 0000:00:00.0: failed to fetch board file: -12 ath10k_pci 0000:00:00.0: could not probe fw (-12) As described already in 2d3321619b2b ("ath79: TP-Link EAP245 v3: use pre-calibration nvmem-cell"): Ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Further rename the nvmem cell node and label to match the updated cell name. Fixes: 23b904074500 ("ath79: TP-Link EAP225-Outdoor v1: convert ath10k to nvmem-cells") Suggested-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: UniFi 6 LR: disable RTCDaniel Golle2022-06-181-0/+6
| | | | | | | | There is not RTC battery connected to the SoC of the UniFi 6 LR board. Disable the RTC to prevent the system coming up with time set to 2000-01-01 00:00:00 after each reboot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: D-Link DAP-2xxx (QCA953x): convert ath9k caldata to nvmemSander Vanheule2022-06-181-2/+11
| | | | | | | | | | Convert the calibration data reference for the ath9k radio to an nvmem-cell, replacing the downstream mtd-cal-data property. Since the 'art' label is no longer used, it can be dropped. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2xxx (QCA953x): move art partition to DTSISander Vanheule2022-06-183-12/+6
| | | | | | | | | The art partition containing the radio calibration data is in the same location for all supported devices. Move the definition to the base file so the reference from the wmac node can reference the same file. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-3662 A1: convert ath10k caldata to nvmemSander Vanheule2022-06-183-9/+16
| | | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. MAC address assignment is moved to '10_fix_wifi_mac', so the device can then be removed from the caldata extraction script '11-ath10k-caldata'. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2695 A1: convert ath10k caldata to nvmemSander Vanheule2022-06-183-3/+16
| | | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. MAC address assignment is moved to '10_fix_wifi_mac', so the device can then be removed from the caldata extraction script '11-ath10k-caldata'. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-23 22:33:41 +0000