aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mac80211: ath10k add leds supportAnsuel Smith2018-06-221-0/+617
| | | | | | | This adds support for leds handled by the wireless chipset. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> (cherry picked from commit 61d57a2f88b90ba951012e66c7c6fae9234c97b4)
* wwan: Add support for Gemalto Cinterion cellular modulesDavid Thornley2018-06-224-1/+17
| | | | | | | | | | | | | | Includes specific support for PH8(1e2d-0053) / ELS61(1e2d-005b) modules. Note for ELS61, the serial driver changes from serial option(ttyUSB) to usb-cdc (ttyACM). Two additional fixes in this commit resolve issues with ttyACM devices: - * wwan.sh - sys-fs has a subdirectory indirection (*/tty/ttyACMx) which was not handled properly * wwan.usb - dependent scripts were not included, so this never actually called proto_set_available for example (and relied on inadvertent call for ttyUSB case) Signed-off-by: David Thornley <david.thornley@touchstargroup.com> (cherry picked from commit cb262b09396edd171eb3903e50ce5ddeb593f963)
* busybox: udhcpc: replace udhcpc_no_msg_dontroute patch by upstream fixHans Dedecker2018-06-213-12/+118
| | | | | | | | Replace 204-udhcpc_no_msg_dontroute patch by the upstream busybox fix which removes the code which requires the server ID to be on local network Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: backport fix for missing tunnel encapsulation limit optionHans Dedecker2018-06-212-0/+81
| | | | Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* lantiq: fix arcadyan vg3503j switch port indexingMathias Kresin2018-06-211-1/+1
| | | | | | | Both version of the vg3503j have the LAN1 labelled port connected to switch port 4 and the LAN2 labelled port connected to switch port 2. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add support for Phicomm K2GChuanhong Guo2018-06-215-1/+155
| | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: MediaTek MT7620A - Flash: 8 MB - RAM: 64 MB - Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5) - Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA. - UART: 1 x UART on PCB - 57600 8N1 Flash instruction: The U-boot is based on Ralink SDK so we can flash the firmware using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB. 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* Revert "base-files: fix UCI config parsing and callback handling"Hans Dedecker2018-06-212-6/+9
| | | | | | | This reverts commit 023944853241920c20842c0f4649d1dd4e7e273b as users report Qos scripts are broken (FS#1602) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mt76: update to the latest versionFelix Fietkau2018-06-211-3/+3
| | | | | | | | 072fdac mt76x2: mac: consider multicast/broadcast frames in ewma rssi estimation f450659 mt76x2: improve gain adjustment in noisy environments 1d4ca10 mt76x2: track rssi for gain adjustment per station Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for TP-LINK Archer C7 v5Arvid E. Picciani2018-06-2110-2/+275
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros QCA9563+QCA9880. Specification: - 750/400/250 MHz (CPU/DDR/AHB - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 10x LED, 2x button - UART header on PCB Flash instruction: 1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin and rename it to ArcherC7v5_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Arvid E. Picciani <aep@exys.org> (cherry picked from commit bf39d5594b3c8f9409e6d9408a1f370c9f18d0dd)
* ar71xx: add support for Fritz!WLAN Repeater 450EDavid Bauer2018-06-2113-1/+212
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!WLAN Repeater 450E SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc RAM: 64MB Zentel A3R12E40CBF DDR2 FLASH: 16MiB Winbond W25Q128 SPI NOR WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3 INPUT: WPS button LED: Power, WiFi, LAN, RSSI indicator Serial: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4GHz WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - Most LEDs Not working: - 2 RSSI LEDs AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they control over MDIO. Our driver doesn't expose these LEDs as GPIOs. While it is possible to implement this feature, it would require an additional kernel patch for a minor functionality. Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 192.168.178.1. Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. You need to powercycle the Device afterwards to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit b4bf43c66767648f98494dd5f44e1301024b577c)
* ipq40xx: add support for ZyXEL WRE6606Magnus Frühling2018-06-219-3/+302
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com> (cherry picked from commit 4b280ad91a6b155ac71c417aaa7bb5f4e328712f)
* ar71xx: add support for OCEDO KoalaDavid Bauer2018-06-2114-0/+206
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit e36f8b3f3980903d5cefc51fe274c19c7a0719f2)
* ar71xx: fix incorrect speed setting on QCA9556David Bauer2018-06-211-3/+17
| | | | | | | | | | The QCA9556 only has a SGMII interface. However the speed on the ethernet link is set for the non-existant xMII interface. This commit fixes this behavior. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit abb4ab076f37961a4dcaef4e87167b834f84e44e)
* ramips: Add support for Mikrotik RouterBOARD RBM33gTobias Schramm2018-06-217-1/+187
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Mikrotik RouterBOARD RBM33g. =Hardware= The RBM33g is a mt7621 based device featuring three gigabit ports, 2 miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male onboard RS-232 serial port. Additionally there are a lot of accessible GPIO ports and additional buses like i2c, mdio, spi and uart. ==Switch== The three Ethernet ports are all connected to the internal switch of the mt7621 SoC: port 0: Ethernet Port next to barrel jack with PoE printed on it port 1: Innermost Ethernet Port on opposite side of RS-232 port port 2: Outermost Ethernet Port on opposite side of RS-232 port port 6: CPU ==Flash== The device has two spi flash chips. The first flash chips is rather small (512 kB), connected to CS0 by default and contains only the RouterBOOT bootloader and some factory information (e.g. mac address). The second chip has a size of 16 MB, is by default connected to CS1 and contains the firmware image. ==PCIe== The board features three PCIe-enabled slots. Two of them are miniPCIe slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2). Each of the miniPCIe slots is connected to a dedicated mini SIM socket on the back of the board. Power to all three PCIe-enabled slots is controlled via GPIOs on the mt7621 SoC: PCIe0: GPIO9 PCIe1: GPIO10 PCIe2: GPIO11 ==USB== The board has one external USB 3.0 port at the rear. Additionally PCIe port 0 has a permanently enabled USB interface. PCIe slot 1 shares its USB interface with the rear USB port. Thus only either the rear USB port or the USB interface of PCIe slot 1 can be active at the same time. The jumper next to the rear USB port controls which one is active: open: USB on PCIe 1 is active closed: USB on rear USB port is active ==Power== The board can accept both, passive PoE and external power via a 2.1 mm barrel jack. The input voltage range is 11-32 V. =Installation= ==Prerequisites== A USB -> RS-232 Adapter and a null modem cable are required for installation. To install an OpenWRT image to the device two components must be built: 1. A openwrt initramfs image 2. A openwrt sysupgrade image ===initramfs & sysupgrade image=== Select target devices "Mikrotik RBM33G" in openwrt menuconfig and build the images. This will create the images "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output directory. ==Installing== **Make sure to back up your RouterOS license in case you do ever want to go back to RouterOS using "/system license output" and back up the created license file.** Serial settings: 115200 8N1 The installation is a two-step process. First the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted via tftp: 1. Set up a dhcp server that points the bootfile to tftp server serving the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" initramfs image 2. Connect to WAN port (left side, next to sys-LED and power indicator) 3. Connect to serial port of board 4. Power on board and enter RouterBOOT setup menu 5. Set boot device to "boot over ethernet" 6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server allows dynamic bootp) 6. Save config 7. Wait for board to boot via Ethernet On the serial port you should now be presented with the OpenWRT boot log. The next steps will install OpenWRT persistently. 1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device using scp. 2. Write openwrt to flash using "sysupgrade openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" Once the flashing completes reboot the router and let it boot from flash. It should boot straight to OpenWRT. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: Add lzma-loader targetsTobias Schramm2018-06-211-0/+16
| | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: Add support for mt7621 to lzma-loaderTobias Schramm2018-06-215-18/+60
| | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: fix Newifi D1 mtd partitionDeng Qingfang2018-06-211-1/+1
| | | | | | Newifi D1 has 32 MiB flash, so the firmware partition size should be 0x1fb0000 Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* wireguard: bump to 0.0.20180620Kevin Darbyshire-Bryant2018-06-201-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | 0bc4230 version: bump snapshot ed04799 poly1305: add missing string.h header cbd4e34 compat: use stabler lkml links caa718c ratelimiter: do not allow concurrent init and uninit 894ddae ratelimiter: mitigate reference underflow 0a8a62c receive: drop handshake packets if rng is not initialized cad9e52 noise: wait for crng before taking locks 83c0690 netlink: maintain static_identity lock over entire private key update 0913f1c noise: take locks for ss precomputation 073f31a qemu: bump default kernel bec4c48 wg-quick: android: don't forget to free compiled regexes 7ce2ef3 wg-quick: android: disable roaming to v6 networks when v4 is specified 9132be4 dns-hatchet: apply resolv.conf's selinux context to new resolv.conf 41a5747 simd: no need to restore fpu state when no preemption 6d7f0b0 simd: encapsulate fpu amortization into nice functions f8b57d5 queueing: re-enable preemption periodically to lower latency b7b193f queueing: remove useless spinlocks on sc 5bb62fe tools: getentropy requires 10.12 4e9f120 chacha20poly1305: use slow crypto on -rt kernels on arm too Compiled-for: ar71xx, lantiq Run-tested-on: ar71xx Archer C7 v2 & lantiq HH5a Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* dnsmasq: fix dnsmasq startup issueHans Dedecker2018-06-202-9/+1
| | | | | | | | | | | Commit ecd954d530 installs specific interface triggers which rewrites the dnsmasq config file and restarts dnsmasq if the network interface becomes active for which a trigger has been installed. In case no dhcp sections are specified or ignore is set to 1 dnsmasq will not be started at startup which breaks DNS resolving. Fix this by ditching the BOOT check in start_service and always start dnsmasq at startup. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: add support for ELECOM WRC-1167GHBK2-SINAGAKI Hiroshi2018-06-196-4/+175
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - MT7621A (2-Cores, 4-Threads) - 128 MB of RAM (DDR3) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz - MediaTek MT7615D - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 2x keys - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 57600 bps Flash instruction using factory image: 1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin" 2. Connect the computer to the LAN port of WRC-1167GHBK2-S 3. Connect power cable to WRC-1167GHBK2-S and turn on it 4. Access to "http://192.168.2.1/details.html" and open firmware update page ("手動更新（アップデート）") 5. Select the factory image and click apply ("適用") button 6. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for I-O DATA WN-GX300GRINAGAKI Hiroshi2018-06-196-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek MT7621S. Specification: - MT7621S (1-Core, 2-Threads) - 64 MB of RAM - 8 MB of Flash (SPI) - 2T2R 2.4 GHz - 5x 10/100/1000 Mbps Ethernet - 2x LEDs, 4x keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 115200 bps (U-Boot, OpenWrt) Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR" and place it in the TFTP directory 3. Set the IP address of the computer to 192.168.99.8, connect to the LAN port of WN-GX300GR, and start the TFTP server on the computer 4. Connect power cable to WN-GX300GR and turn on the router 5. Press "1" key on the serial console to interrupt boot process on U-Boot, press Enter key 3 times and start firmware download via TFTP 6. WN-GX300GR downloads initramfs image and boot with it 7. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for WN-GX300GR 8. Wait ~150 seconds to complete flasing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-199-7/+484
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: mt7621: fix wireless package selectionMathias Kresin2018-06-191-5/+4
| | | | | | | Add wpad-mini if wireless drivers are included. Drop the mt76 package if both of the provided drivers are included with their own packages. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ds-lite: make tunnel encapsulation limit support configurable (FS#1501)Hans Dedecker2018-06-192-3/+7
| | | | | | | | | | | | Be compatible with ISPs which don't support the destination option header containing the tunnel encapsulation limit as reported in FS#1501. Setting the uci parameter encaplimit to ignore; allows to disable the insertion of the destination option header in the ds-lite packets. Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255 by setting the encaplimit uci parameter accordingly. If no encaplimit value is specified the default value is 4 as before. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* odhcp6c: make ds-lite/map tunnel encapsulation limit support configurable ↵Hans Dedecker2018-06-193-3/+9
| | | | | | | | | | | | | | (FS#1501) Be compatible with ISPs which don't support the destination option header containing the tunnel encapsulation limit as reported in FS#1501 for dynamic created ds-lite/map interfaces. Setting the uci parameter encaplimit_dslite/map to ignore; allows to disable the insertion of the destination option header for the dynamic created ds-lite/map interface. Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255 by setting the encaplimit_dslite/map uci parameter accordingly. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* netifd: update to latest git HEAD (FS#1501)Hans Dedecker2018-06-191-3/+3
| | | | | | a580028 system-linux: make encaplimit configurable for ip6 tunnels (FS#1501) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* map: make tunnel encapsulation limit support configurable (FS#1501)Hans Dedecker2018-06-192-8/+10
| | | | | | | | | | | | Be compatible with ISPs which don't support the destination option header containing the tunnel encapsulation limit as reported in FS#1501. Setting the uci parameter encaplimit to ignore; allows to disable the insertion of the destination option header in the map-e packets. Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255 by setting the encaplimit uci parameter accordingly. If no encaplimit value is specified the default value is 4 as before. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mvebu: reduce speed to gen1 for espressobin pcieTomasz Maciej Nowak2018-06-192-0/+116
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the beginning there's been an issue with initializing the Atheros based MiniPCIe wireless cards. Here's an example of kerenel log: OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit] pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref] [...] advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k 0000:00:00.0: enabling device (0000 -> 0002) advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40 ath9k 0000:00:00.0: request_irq failed advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k: probe of 0000:00:00.0 failed with error -22 The same happens for ath5k cards, while ath10k card didn't appear at all (not detected): OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link never came up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) advk-pcie d0070000.pcie: config read/write timed out Following the issue on esppressobin.net forum [1] the workaround seems to be limiting the speed of PCIe bridge to 1st generation. This fixed the initialisation of all tested Atheros wireless cards. The change shouldn't affect the performance for wireless cards, it could reduce the performance of storage controller cards but since OpenWrt focuses on wireless connectivity, fixing compatibility with wireless cards should be a priority. For the record, the iwlwifi and mt76 cards were not affected by this issue. 1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> (cherry picked from commit 772258044b48036699302840abf96cd34c4e5078)
* mvebu: add fix for armada 37xx cpufreq driverTomasz Maciej Nowak2018-06-191-0/+35
| | | | | | | Backport from stable kernel tree fixing clock leak. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> (cherry picked from commit 4ec8c8c23ed50dbe9cabbfc544ae2780f0287fd0)
* kernel: add missing softdog symbolJohn Crispin2018-06-191-1/+2
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit 9c409cb4e2670edddd8de5e8536ea295d44b9e16)
* build: add busybox support to `time` prereq-checkAndy Boyett2018-06-182-3/+4
| | | | | | | | | | | | | | | Busybox time supports the GNU time '-f' syntax used by the build time logging implemented in ff6e62b288c, however the prerequisite check added only works with GNU time installed as `time` or `gtime`. As busybox is a multicall binary, the name of the symlink setup by SetupHostCommand also must be changed from `gtime` to `time` to fix the value of argv[0]. This causes a number of shells (including bash) to use their builtin impelementation of time, so the sole invocation has been changed to use `env time` to use the value found on the $PATH. Signed-off-by: Andy Boyett <agb@agb.io> (cherry picked from commit 591780615b304fb4624e363135942e9ee8f6caa3)
* build: use busybox gzip compatible force optionMathew McBride2018-06-181-1/+1
| | | | | | | | | | | commit 138c763 ("build: add --force option to gzip in Build/gzip") added the --force flag to the gzip invocation. Under environments with busybox gzip (e.g Alpine Linux), this fails as busybox only recognizes "-f". Signed-off-by: Mathew McBride <matt@traverse.com.au> (cherry picked from commit fba168f5745acac95db519a9984b62e3e508df6a)
* kernel: atm: pppoatm fix vc-mux connection failuresKevin Darbyshire-Bryant2018-06-181-0/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Backport a hot off the press upstream kernel ATM fix: Preserve value of skb->truesize when accounting to vcc "There's a hack in pskb_expand_head() to avoid adjusting skb->truesize for certain skbs. Ideally it would cover ATM too. It doesn't. Just stashing the accounted value and using it in atm_raw_pop() is probably the easiest way to cope." The issue was exposed by upstream with: commit 14afee4b6092fde451ee17604e5f5c89da33e71e Author: Reshetova, Elena <elena.reshetova@intel.com> Date: Fri Jun 30 13:08:00 2017 +0300 net: convert sock.sk_wmem_alloc from atomic_t to refcount_t But an earlier commit left the ticking timebomb: 158f323b9868 ("net: adjust skb->truesize in pskb_expand_head() Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging assistance and to David Woodhouse <dwmw2@infradead.org> for further guidance, cajoling & patience in interpreting the debug I was giving him and producing a fix! Fixes FS#1567 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> (cherry picked from commit d600de3ddde269bf0b324735f8f12278f82d9b37)
* include/image-commands.mk: shorter version in Netgear factory headerHannu Nyman2018-06-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Shorten the version string in Netgear factory image header in order to enable u-boot TFTP recovery flash mode to work again. Strip 'r7210-14cb05909a' into 'r7210' in the Netgear image header by removing the hash (anything after "-"). background: Some Netgear routers have recently been unable to flash Openwrt factory image with the TFTP recovery flash mode provided by Netgear u-boot. That is due to over-long Openwrt version string overflowing into the router type string in u-boot code. Modern git versions produce 10-digit short hashes for the Openwrt main repo, and that causes the version string to be too long in the image header, breaking the image ID verification by the TFTP flash routine. (Other option could be to force a shorter hash in scripts/getver.sh, but as the problem only concerns Netgear routers, let's patch just them.) More detailed explanations in FS#1583 Tested with WNDR3800 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> (cherry picked from commit dcfe2a461e4b06de6e2b23d29afebbb3c775f647)
* mips: fix dynamic ftraceVincent Wiemann2018-06-181-3/+8
| | | | | | | | | | | The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as dynamic ftrace depends on -mlong-calls. See http://patchwork.linux-mips.org/patch/675/ Thus we always set -mlong-calls if the kernel is being compiled with dynamic ftrace support. Signed-off-by: Vincent Wiemann <webmaster@codefetch.de> (cherry picked from commit 076d2ea6829855ee14ebd65230146eb27ee16750)
* ar71xx: add kmod-usb-ehci to fix USB on RB hAP ACThomas Nixon2018-06-181-1/+1
| | | | | Signed-off-by: Thomas Nixon <tom@tomn.co.uk> (cherry picked from commit bb71a3f27efb4140c47e98b933bdb64384cbcbbf)
* ipq40xx: essedma: fixup ip alignChen Minqiang2018-06-181-0/+26
| | | | | | | | | This fixup ip align in essedma driver rx path see cat /proc/cpu/alignment which reports alignment-fixups without this fix. Signed-off-by: Chen Minqiang <ptpt52@gmail.com> (cherry picked from commit 8f804f42d52e49191429ad1d716e7adb3cd10ceb)
* ipq806x: D7800 only has a single sata portJohn Crispin2018-06-181-0/+1
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit ee1dbffeed442b4968af48b2492ad41ac988dab8)
* mvebu: backport ahci_mvebu errata patchsetJeremiah McConnell2018-06-182-0/+334
| | | | | | | | | | | | | Marvell ahci hardware requires a workaround to prevent eSATA failures on hotplug/reset when used with multi-bay external enclosures. Errata Ref#226 - SATA Disk HOT swap issue when connected through Port Multiplier in FIS-based Switching mode. These patches backport the workaround from 4.17. Signed-off-by: Jeremiah McConnell <miah@miah.com> (cherry picked from commit e820455198aa50cc32f9a108a4696f0cc23023c3)
* cron: add procd listeners for crontabsPaul Spooren2018-06-181-3/+5
| | | | | | | | | Add procd file listeners to check files in `/etc/crontabs/`. Also unified a bit the function style. Signed-off-by: Paul Spooren <mail@aparcar.org> (cherry picked from commit cbf69fb2adced6096addbe6aeb54c1971c63dbe4)
* mediatek: mt7622: Do not deactivate CONFIG_BLK_DEVHauke Mehrtens2018-06-181-1/+0
| | | | | | | | | | | zram.ko needs CONFIG_BLK_DEV activated and it is by default for all other targets in OpenWrt. This makes zram.ko compile again. Compile tested only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 6745af9a0de28171b45c0e8584e393bd80f0a377)
* mediatek: mt7622: Do not set CPU_SUBTYPE for Cortex A53Hauke Mehrtens2018-06-181-1/+0
| | | | | | | | | | | | | Neon and vfpv4 are mandatory extensions in the ARM64 instruction set now, do not activate them explicitly. GCC will make use of these extension now by default. This makes it possible to share the toolchain with other Cortex A53 SoCs. Compile tested only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 10ce015c652b1e48c1c113604e26481626fa6059)
* mvebu: enable SATA port multiplier supportJeremiah McConnell2018-06-181-0/+1
| | | | | | | | | | | Some of the Marvell targets have functional SATA port multiplier support, which is required for multi-bay eSATA enclosures. Enable kernel support by setting CONFIG_SATA_PMP. Closes: FS#1232 and FS#547 Signed-off-by: Jeremiah McConnell <miah@miah.com> (cherry picked from commit 390c4df2c0b2e7b31c52eca3dcba139b0d745a97)
* ltq-vdsl-mei: reset g_tx_link_rate on showtime exitMartin Schiller2018-06-181-0/+12
| | | | | | | | | | | | | Without this change, ifx_mei_atm_showtime_check() will always return "showtime" after one call of MEI_InternalXtmSwhowtimeEntrySignal() was done, even if MEI_InternalXtmSwhowtimeExitSignal() was called in the meantime. The ifx_mei_atm_showtime_check() function is used by the ltq-atm and ltq-ptm driver. Signed-off-by: Martin Schiller <ms@dev.tdt.de> (cherry picked from commit eee8ab59dc8bc4c599b3508201349fdd96463e69)
* ar71xx: Fix offset to WMAC address for 8devices LimaSven Eckelmann2018-06-181-3/+1
| | | | | | | | | | | | | | | | | | | The ART partition of the Lima board stores exactly three mac addresses: * 0x0: eth0 * 0x6: eth1 * 0x1002: wmac The first two are correctly assigned in the mach file but the latter points to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when it doesn't find a valid mac address in the platform_data. Remove this bogus offset to the ART partition to directly load the wmac via the EEPROM data in the ART partition. Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit 4f6320704f7e37368a1dae2deba767a73b3bf121)
* ipq806x: Limit NR_CPUS to 2Rosen Penev2018-06-181-1/+1
| | | | | | | | | | | ipq806x is all dual core processors. ipq807x is quad core. Removes this from dmesg: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit fff65dbe2436351ea1feee6c79110971ec4d5881)
* mtd: mark as nonshared to fix FS#484Mirko Parthey2018-06-181-0/+2
| | | | | | | | | | | The mtd tool is built with different configurations depending on the target. For example, brcm47xx adds the fixtrx subcommand, without which an image fails when booting the second time. Mark the mtd package as nonshared to really fix FS#484. Signed-off-by: Mirko Parthey <mirko.parthey@web.de> (cherry picked from commit 46d7ced9d1e104693a9f995bfe8a6e28ac82b592)
* mediatek: add missing symbols for mt7622John Crispin2018-06-181-1/+1
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit 55f37310020c48ff575158791eb8dbcc6802c549)
* mediatek: add missing symbolsJohn Crispin2018-06-182-8/+8
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit de6162e832d028d24267d9cbfc64c71b9a7c5ec9)
* mediatek: add mt7622 subtargetJohn Crispin2018-06-187-1/+565
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit 51740777fb37cb7bdc250d74b366840269439cf3)
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 01:11:29 +0000