aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for TP-Link TL-WR802N V1 and V2Lech Perczak2020-05-316-1/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc) - RAM: 32 MiB - Storage: 4 MiB of Flash on board - Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) Installation through OEM Web Interface: - Connect to TL-WR802N by Ethernet or Wi-Fi - Go to web interface: [V1] http://192.168.0.1 [V2] http://192.168.0.254 Default user is "admin" & password is "admin". On V2, there is no DHCP server running by default, so remember to set IP manually. - Go to "System Tools -> Firmware Upgrade" - Browse for firmware: [V1] "*.factory.bin" [V2] "*.factory-us.bin" or "*.factory-eu.bin" for eu model Web interface may complain if filename is too long. In such case, rename .bin to something shorter. - Click upgrade Installation through tftp: Note: T_OUT, T_IN and GND on the board must be connected to USB TTL Serial Configuration 115200 8n1 - Boot the TL-WR802N - When "Autobooting in 1 seconds" appears type "tpl" followed by enter - Connect to the board Ethernet port (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10) - tftpboot 0x80000000 <Firmware Image Name> - Record the result of "printenv bootcmd" - Enter "erase <Result of 'printenv bootcmd'> +0x3c0000" (e.g erase 0x9f020000 +0x3c0000) - Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000" (e.g cp.b 0x80000000 0x9f020000 0x3c0000) - Enter "bootm <Result of 'printenv bootcmd'>" (e.g bootm 0x9f020000) Notes: When porting from ar71xx target to ath79, I found out that on V2, reset button is on GPIO12 and active low, instead of GPIO11 and active high. By cross-flashing V1 firmware to V2, I confirmed the same is true for V1. Also according to manual of V1, this one also has green LED instead of blue - both of those issues were fixed accordingly. The MAC address assignment has been checked with OEM firmware. Installation manual based on ar71xx support by Thomas Roberts Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [slightly adjust commit message, add MAC address comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix reset key for TP-Link TL-WR802N V1/V2Lech Perczak2020-05-311-2/+2
| | | | | | | | | | | | | | | | | | During porting support for this router to ath79 target it was discovered that GPIO mapping was incorrect (GPIO11 active high). Correct mapping for both V1 and V2 is GPIO12 active low. Default configuration from GPL source for V2 explicitly states this, and this was confirmed experimentally on ath79 by looking on /sys/kernel/debug/gpio. Correctness of this was also validated for V1 by cross-flashing vendor firmware for V1 on V2 hardware, in which reset button also worked. Fix it. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [slightly adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: update WA/XC devices UBNT_VERSION to 8.5.3Roger Pueyo Centelles2020-05-311-3/+3
| | | | | | | | | | | | | | Ubiquiti WA devices with newer hw version 2011K require UBNT_VERSION to be at least 8.5.3, otherwise the image is rejected: New ver: WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3 Versions: New(525568) 8.5.0, Required(525571) 8.5.3 Invalid version 'WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3' For consistency, also increase version number for XC devices. Tested-by: Pedro <pedrowrt@cas.cat> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ipq806x: EA8500 fix boot partition detectionSamantha Collard2020-05-311-2/+0
| | | | | | | Remove extraneous code that disabled boot partition detection. Fixes: b3770eaca39f ("mtd: base-files: Unify dual-firmware devices (Linksys)") Signed-off-by: Samantha Collard <sammyrc34@gmail.com>
* ath79: fix LEDs for GL.inet GL-AR150Adrian Schmutzler2020-05-312-12/+10
| | | | | | | | | | | | | | | | | Since the wireless LED was used for boot and set up with a DT trigger, the WiFi indication hasn't worked on ath79 at all. In addition, a look into the manual revealed that the OEM configuration is as follows: LED 1 (green): power LED 2 (green): configurable LED 3 (red): wireless So, let's just keep the WiFi trigger and convert the rest to its "intended" use. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mt76: update to the latest version (adds 7663e, 7663u, 7915 drivers)Felix Fietkau2020-05-311-10/+87
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 7aabfd0c9282 mt7615: add CONFIG_MT76_LEDS to cflags 10a5b7630a37 mt76: mt7615: fix getting maximum tx power from eeprom 8688ed70c987 mt76: mt7615: use module parameter option for offload firmware preference 04798aab1257 net: mt7603: remove duplicate error message 9636177117d8 mt76: mt7615: fix ssid configuration in mt7615_mcu_hw_scan d4ba139d8b8b mt76: mt7615: introduce mt7615_check_offload_capability routine 2cc0d54b65a1 mt76: mt7615: do not mark sched_scan disabled in mt7615_scan_work 5b73be962388 mt76: mt7615: add passive mode for hw scan 96e429e18174 mt76: mt7615: free pci_vector if mt7615_pci_probe fails 8fddbf6390ac mt76: mt7615: introduce support for hardware beacon filter f2c760177bdd mt76: mt7615: introduce mt7615_mcu_set_hif_suspend mcu command db454605106f mt76: mt7615: add WoW support 20b87321c39f mt76: mt7663u: introduce suspend/resume to mt7663u 20db7e73c586 mt76: mt7615: introduce PM support 523716bba561 mt76: mt7615: add gtk rekey offload support 50d377a825cc mt76: mt7615: introduce beacon_loss mcu event 4ef1957cea35 mt76: mt7663: read tx streams from eeprom f25a43cc53e7 mt76: mt7615: check return value of mt7615_eeprom_get_power_index 0a9f71652927 mt76: mt7615: fix ibss mode for mt7663 83f2ba3101b4 mt76: mt7663: fix target power parsing 3e6968593b61 mt76: mt7615: fix delta tx power for mt7663 c1d3ad194ae4 mt76: mt7663: introduce WoW with net detect support 891136ab99da mt76: mt7663: add support to sched scan with randomise addr 82e4d3ebe967 mt76: mt7615: scan all channels if not specified 690b84821cd3 mt76: avoid rx reorder buffer overflow f0117d3107b4 mt76: add support for HE RX rate reporting cc68782bab1a mt76: add Rx stats support for radiotap 3ec47f2fba61 mt76: adjust wcid size to support new 802.11ax generation 0a9f4173dd07 mt76: add HE phy modes and hardware queue c6b002bcdfa6 mt76: add mac80211 driver for MT7915 PCIe-based chipsets b96af5039581 mt76: mt7915: enable Rx HE rate reporting 230054096155 mt76: mt7915: implement HE per-rate tx power support c8f4b6cf1add mt76: mt7915: register per-phy HE capabilities for each interface de1e8af96e19 mt76: mt7915: add HE bss_conf support for interfaces 135a5085932b mt76: mt7915: add HE capabilities support for peers 3b5d908dae2f mt76: mt7915: add Rx radiotap header support 158253e2c11e mt76: mt7915: add .sta_add_debugfs support 7f40e8c2b98d mt76: mt7915: add .sta_statistics support a5368e5cad11 mt76: mt7915: set peer Tx fixed rate through debugfs 4f79c516be5c mt76: mt7915: add tsf related callbacks 509fceb43235 mt76: mt7915: enable firmware module debug support 56405976fc7b mt76: set runtime stream caps by mt76_phy 6bbf1a35c0da linux-firmware: add rebb firmware for mt7663 d7a10094c4e5 mt7663: add client offload firmware 9200732e8534 mt76: mt7663u: copy key pointer in mt7663u_mac_write_txwi 3aa810bde810 mt76: mt7663u: add missing register definitions e236ea5be344 mt76: mt7615: usb: cancel ps work stopping the vif 1d0903de2131 mt76: mt7915: introduce mt7915_get_he_phy_cap 095c72c81c74 mt76: mt7915: add Tx beamformer support 5f9e7664cd26 mt76: mt7915: add Tx beamformee support ac505404c385 mt76: mt7915: add TxBF capabilities 6656bebd39cd mt76: mt7915: add debugfs to track TxBF status 9590db025475 mt76: mt7915: allocate proper size for tlv tags 26eb1ed65987 mt76: mt7915: fix possible deadlock in mt7915_stop f85c1f3fc189 firmware: add mt7915 firmware 9b07251b00b0 mt76: mt7615: fix typo defining ps work 060e375a9244 mt76: fix per-driver wcid range checks after wcid array size bump 7270b56389a9 mt76: mt7615: do not report scan_complete twice to mac80211 8c9e4847d01e mt76: mt7615: reduce hw scan timeout 8bd88a1b1880 mt76: enable p2p support 1ea444d0e8e5 mt76: mt7615: configure bss info adding the interface fa81da5bb4e9 mt76: mt7615: introduce remain_on_channel support 44f2262c0289 mt76: mt76x02: remove check in mt76x02_mcu_msg_send 7005aa891440 mt76: mt7915: add spatial reuse support 1e3dc5b76649 mt76: mt7915: fix some sparse warnings 01b784174cd5 mt76: mt7915: fix sparse warnings: incorrect type initializer 40b7b5354a16 mt76: mt7615: fix NULL pointer deref in mt7615_register_ext_phy 6d731d188d31 mt76: mt7915: fix decoded radiotap HE flags b74d5b1c14cf mt76: mt7915: fix some sparse warnings 6679d35be5cc mt76: mt7615: switch to per-vif power_save support 01e870b44769 mt76: mt7915: fix a handful of spelling mistakes 7b2d16655904 mt76: mt7663: fix the usage WoW with net detect support ed3a244fb647 mt76: mt7915: Fix build error 5396a61cec99 mt76: mt7615: fix hw_scan with ssid_type for specified SSID only 466a5b4d041d mt76: mt7915: fix possible NULL pointer dereference in mt7915_register_ext_phy 984a172609c0 mt76: fix wcid allocation issues 6e02acddcb1a mt76: mt7615: add support for MT7611N 4e6f4e432d0d mt76: only iterate over initialized rx queues 9ad940fee593 mt76: mt7615: Use kmemdup in mt7615_queue_key_update() 85c516081338 mt76: mt7915: remove set but not used variable 'msta' Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: compress kernel debuginfo using zstdMatthias Schiffer2020-05-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | zstd with its default settings (compression level -3) compresses better than bzip2 -9 (which is the default setting), and is an order of magnitude faster. I made the following measurements for the most common compression tools (all standard Debian Buster versions, default flags unless noted otherwise), using the debug information of a large x86-64 kernel with ALL_KMODS: * kernel-debug.tar: 376M * kernel-debug.tar.gz: 101M, compressed in ~12s * kernel-debug.tar.bz2: 91M, compressed in ~15s * kernel-debug.tar.xz: 57M, compressed in ~101s * kernel-debug.tar.zst: 86M, compressed in ~1s With zstd, there is still some room for improvement by increasing the compression, but the slight increase in compression ratio (22.83% -> 19.46%) does not justify the significant increase in compression time (about 5 times on my machine) in my opinion. Note that multithreaded compression (-T argument) does not affect reproducibility with zstd. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* build: add zstd support to pack/unpack functionsMatthias Schiffer2020-05-312-0/+5
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* tools: add zstdMatthias Schiffer2020-05-313-1/+82
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* dropbear: add ed25519 and chacha20-poly1305Vladislav Grishenko2020-05-305-3/+3613
| | | | | | | | | | | | - add Ed25519 support (backport): * DROPBEAR_ED25519 option for ssh-ed25519, * disabled by default - add Chacha20-Poly1305 support (backport): * DROPBEAR_CHACHA20POLY1305 for chacha20-poly1305@openssh.com, * enabled by default - update feature costs in binary size Signed-off-by: Vladislav Grishenko <themiron@mail.ru>
* mac80211: fix wifi teardownJohn Crispin2020-05-301-4/+6
| | | | | | reverts part of the recent wifi reconf patch. Signed-off-by: John Crispin <john@phrozen.org>
* bcm53xx: remove support for kernel 4.14Adrian Schmutzler2020-05-3042-4583/+0
| | | | | | | | | We currently support three kernel versions on this target, let's just get rid of the oldest one. Cc: Rafał Miłecki <rafal@milecki.pl> Cc: John Crispin <john@phrozen.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm47xx: remove support for kernel 4.14Adrian Schmutzler2020-05-3025-2795/+0
| | | | | | | | We currently support three kernel versions on this target, let's just get rid of the oldest one. Cc: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mac80211: rt2x00: backport patch enabling MFPDaniel Golle2020-05-301-0/+44
| | | | | | | | | | | | From: Rui Salvaterra <rsalvaterra@gmail.com> Date: Mon, 25 May 2020 14:49:07 +0100 Subject: [PATCH] rt2800: enable MFP support unconditionally This gives us WPA3 support out of the box without having to manually disable hardware crypto. The driver will fall back to software crypto if the connection requires management frame protection. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ugps: nmea: make sure date is validDaniel Golle2020-05-291-3/+3
| | | | | | | | | | | GPS time without date was previously used to set system date: Tue Oct 10 11:48:21 2000 user.info kernel: [ 108.786639] ugps: system time differs from GPS time by more than 5 seconds. Using 2000-10-10T10:48:21 UTC as the new time Tue Oct 10 11:49:27 2000 user.info kernel: [ 174.794699] ugps: system time differs from GPS time by more than 5 seconds. Using 2020-05-26T10:49:27 UTC as the new time Fix this by ignoring incomplete dates and wait for complete time information before adjusting system date/time. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ar71xx: fix splitting firmware partition for TL-WR902AC v1Adrian Schmutzler2020-05-301-0/+2
| | | | | | | | | | | | The -O option for the tplink-v1-header was missing for the TP-Link TL-WR902AC v1, while safeloader and MTDPARTS where set up with a single firmware partition. This led to bootloops after using sysupgrade. Fixes: FS#3118 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* qos-scripts: fix interface resolvingJo-Philipp Wich2020-05-292-8/+14
| | | | | | | | Also ensure that the error message is actually printed to stderr and that the rule generation is aborted if an interface cannot be resolved. Ref: https://github.com/openwrt/luci/issues/3975 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ccache: update to 3.7.9DENG Qingfang2020-05-282-3/+3
| | | | | | | | | Update ccache to 3.7.9 Release notes: https://ccache.dev/releasenotes.html#_ccache_3_7_9 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* bcm27xx: update to latest patches from RPi foundationÁlvaro Fernández Rojas2020-05-28560-220/+373
| | | | | | | Also removes random module and switches to new bcm2711 thermal driver. Boot tested on RPi 4B v1.1 4G. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx-userland: update to latest versionÁlvaro Fernández Rojas2020-05-282-2/+79
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* procd: update to git HEADDaniel Golle2020-05-281-3/+3
| | | | | | | b84a329 jail: use sane termios settings for console pts b9b39e2 jail: handle containers seperately Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: Add disable_vht when using NOHT/HT* modesEnrique Rodríguez Valencia2020-05-281-1/+2
| | | | | | disable_vht parameter needs to be set when using wpa_supplicant NOHT/HT* modes. Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
* mac80211: Fix setting radio htmode when using mesh modeEnrique Rodríguez Valencia2020-05-281-0/+1
| | | | | | | When configuring the radio in legacy mode from luci, the htmode is not set correctly to NOHT, causing the radio in mesh mode to be set to HT40. Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
* broadcom-wl: don't inherit lock descriptor in nas processJo-Philipp Wich2020-05-282-2/+5
| | | | | | | | | | | Add a local hack to prevent the Broadcom WPA authenticator process from inheriting the lock descriptor 1000 used to prevent concurrent executions of the init script. Without this fix, repeated invocations of /etc/init.d/network, e.g. for obtaining the enabled state, would hang forever. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* bcm27xx-userland: update to latest version with 64 bit supportÁlvaro Fernández Rojas2020-05-281-2/+2
| | | | | | | | Support for 64 bits has been remove on latest master of raspberry/firmware. Update to latest commit with 64 bit support since we don't support installing 32 bit packages on 64 bit targets. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* linux: mvebu: backport mvneta XDP support fixesJakov Petrina2020-05-284-0/+200
| | | | | | | | | | | | This patch backports additional fixes for XDP support in the mvneta driver. These changes are found upstream as commits: b37fa92e20ef2 net: mvneta: fix build skb for bm capable devices f383b2950070c net: mvneta: rely on page_pool_recycle_direct in mvneta_run_xdp 79572c98c554d mvneta driver disallow XDP program on hardware buffer management 44efc78d0e464 net: mvneta: fix XDP support if sw bm is used as fallback Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
* linux: mvebu: backport mvneta XDP supportJakov Petrina2020-05-288-4/+1322
| | | | | | | | | | | | | | | | | | | | | | This patch backports XDP support in the mvneta driver used by Marvell ARMADA 37x, 38x and 37xx series SoCs. Supported actions are: - XDP_DROP - XDP_PASS - XDP_REDIRECT - XDP_TX Patches are present upstream as following commits: * b0a43db9087a net: mvneta: add XDP_TX support * 9e58c8b41065 net: mvneta: make tx buffer array agnostic * fa383f6b77a2 net: mvneta: move header prefetch in mvneta_swbm_rx_frame * 0db51da7a8e9 net: mvneta: add basic XDP support * 8dc9a0888f4c net: mvneta: rely on build_skb in mvneta_rx_swbm poll routine * 568a3fa24a95 net: mvneta: introduce page pool API for sw buffer manager * ff519e2acd46 net: mvneta: introduce mvneta_update_stats routine Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
* packages/utils: fbtest fix MakefileThibaut VARÈNE2020-05-281-1/+1
| | | | | | | | | The clean target tries to remove what looks like a bogus 'rbcfg', probably carried over copy-pasta. Remove the name of the generated executable ('fbtest') instead. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Fixes: 8099f4e0d3af ("fbtest utility ")
* package/base-files: caldata: work around dd's limitationThibaut VARÈNE2020-05-282-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | tl;dr: dd will silently truncate the output if reading from special files (e.g. sysfs attributes) with a too large bs parameter. This problem was exposed on some RouterBOARD ipq40xx devices which use a caldata payload which is larger than PAGE_SIZE, contrary to all other currently supported RouterBOARD devices: the caldata would fail to properly load with the current scripts. Background: dd doesn't seem to correctly handle read() results that return less than requested data. sysfs attributes have a kernel exchange buffer which is at most PAGE_SIZE big, so only 1 page can be read() at a time. In this case, if bs is larger than PAGE_SIZE, dd will silently truncate blocks to PAGE_SIZE. With the current scripts using bs=<size> count=1, the data is truncated to PAGE_SIZE as soon as the requested <size> exceeds this value. This commit works around this problem by using `cat` in the caldata routines that can read from a file (routines that read from mtd devices are untouched). cat correctly handles partial read requests. The output is then piped to dd with the same parameters as before, to ensure that the resulting file remains exactly the same. This is a simple workaround, the downside is that it uses a pipe and one more executable, and therefore has a larger memory footprint and is slower. This is deemed acceptable considering these routines are only used at boot time. Tested-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* packages/boot: remove rbcfgThibaut VARÈNE2020-05-288-1351/+1
| | | | | | | The new sysfs soft_config driver makes buggy rbcfg obsolete and entirely replaces it. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerboot sysfs: soft_config support for ath79 cpufreqThibaut VARÈNE2020-05-281-2/+64
| | | | | | | | | | | | This commit introduces support for R/W access to the CPU frequency setting of routerboot on ath79 hardware. On unsupported hardware, the sysfs attribute will expose the raw tag value (read-only) to help with reverse engineering its meaning. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerboot sysfs: move tag_show_u32()Thibaut VARÈNE2020-05-283-22/+23
| | | | | | | | This routine will be shared between hard and soft config drivers. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerboot sysfs: add support for soft_configThibaut VARÈNE2020-05-286-2/+711
| | | | | | | | | | | | | | | | | | | This driver exposes the data encoded in the "soft_config" flash segment of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder named "soft_config" through a set of human-and-machine-parseable attributes. Changes can be discarded by writing 0 to the 'commit' attribute, or they can be committed to flash storage by writing 1. This driver does not reuse any of the existing code previously found in the "rbcfg" utility and makes this utility obsolete by providing a clean sysfs interface. Like "rbcfg", this driver requires 4K_SECTORS support since the flash partition in which these parameters are stored is typically 4KB in size. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerboot sysfs: move tag_show_string()Thibaut VARÈNE2020-05-283-11/+15
| | | | | | | | | This routine will be shared between hard and soft config drivers. Also use scnprintf() instead of snprintf(). Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: platform/mikrotik: rb_hardconfig.c minor fixesThibaut VARÈNE2020-05-281-7/+14
| | | | | | | | | | | | | For the sake of strictly typed code, add a missing const qualifier. Add a missing return value in error path. Check the return value of mtd_read(), for good measure. Also demote the error printks of failed sysfs file creation to warn level since they are not fatal in the init() sequence. Finally, add a note regarding PAGE_SIZE and clarify a comment. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: platform/mikrotik: reorder KconfigThibaut VARÈNE2020-05-281-2/+2
| | | | | | | | | The depends and select should apply to the sysfs driver, not the meta config. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* cypress-firmware: add PROVIDES sectionsÁlvaro Fernández Rojas2020-05-281-0/+4
| | | | | | Some firmwares are already provided by linux-firmware. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: update patches from RPi foundationÁlvaro Fernández Rojas2020-05-28416-676/+37487
| | | | | | | | | bcm2708: boot tested on RPi B+ v1.2 bcm2709: boot tested on RPi 3B v1.2 bcm2710: boot tested on RPi 3B v1.2 bcm2711: boot tested on RPi 4B v1.1 4G Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx-gpu-fw: update to latest versionÁlvaro Fernández Rojas2020-05-281-15/+15
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: remove linux 4.19 supportÁlvaro Fernández Rojas2020-05-28826-219516/+0
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath79: add support for COMFAST CF-E130N v2Pavel Balan2020-05-284-0/+169
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless CPE with a single Ethernet port and a 802.11bgn radio. Specifications: - QCA9531 SoC - 1x 10/100 Mbps Ethernet with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 5 dBi built-in antenna - POWER/LAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. The U-boot bootloader also contains a backup TFTP client to upload the firmware from. Upon boot, it checks its ethernet network for the IP 192.168.1.10. Host a TFTP server and provide the image to be flashed as file firmware_auto.bin. MAC address setup: The art partition contains four consecutive MAC addresses: 0x0 aa:bb:cc:xx:xx:c4 0x6 aa:bb:cc:xx:xx:c6 0x1002 aa:bb:cc:xx:xx:c5 0x5006 aa:bb:cc:xx:xx:c7 However, the manufacturer in its infinite wisdom decided that one address is enough and both eth0 and WiFi get the MAC address from 0x0 (yes, that's overwriting the existing and valid address in 0x1002). This is obviously also the address on the device's label. Signed-off-by: Pavel Balan <admin@kryma.net> [fix configs partition, fix IMAGE_SIZE, add MAC address comment, rename ATH_SOC to SOC] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: replace tab after DT label by spaceAdrian Schmutzler2020-05-288-8/+8
| | | | | | The common separator in this case is a single space. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix LED DT label for Zyxel Keenetic StartAdrian Schmutzler2020-05-271-5/+5
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* musl: restore lock skipping for mostly-singlethreaded programs, and related ↵Matthias Schiffer2020-05-263-0/+166
| | | | | | | | | | | | patches The remainder of the patch series proposed by upstream [2] for the locking synchronization issue [1]. [1] https://www.openwall.com/lists/musl/2020/05/22/3 [2] https://www.openwall.com/lists/musl/2020/05/22/10 Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* musl: fix locking synchronization bugMatthias Schiffer2020-05-261-0/+69
| | | | | | | | | | | | | Import proposed upstream fix [2] for the critical locking synchronization bug recently found in musl [1]. This affects all programs that are temporarily multithreaded, but then return to single-threaded operation. [1] https://www.openwall.com/lists/musl/2020/05/22/3 [2] https://www.openwall.com/lists/musl/2020/05/22/10 Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ath79: increase spi clock for D-Link DIR-842Sebastian Schaper2020-05-261-1/+2
| | | | | | | | | AHB is 258 MHz for this device (CPU_PLL / 3), but there is no difference between 64 MHz and 50 MHz for spi-max-frequency, thus increase to 50 MHz. Tested on revisions C1 and C3. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: define switch reset-gpios for D-Link DIR-842Sebastian Schaper2020-05-261-8/+2
| | | | | | | | | | GPIO 11 needs to be pulled high for the external gigabit switch to work, this is currently solved via gpio-hog. Replace with phy0 reset-gpios. Tested on revisions C1 and C3. Reset button is still working for reboot, to enter failsafe, and to enter bootloader http recovery. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: fix LEDs for D-Link DIR-842Sebastian Schaper2020-05-264-30/+12
| | | | | | | | | | | | | | | The device has a total of 8 LEDs, 5 of which are controlled by the switch (LAN 1-4, WAN). Only power, wifi and wps are controlled by the SoC. * led_power is on GPIO 5 (not 15), boot flashing sequence is now visible * remove led 'internet', since it is only connected to the switch * remove ucidef_set_led_switch for WAN from 01_leds, as it has no effect Tested on revisions C1 and C3. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> [adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* glibc: update to latest 2.31 commit (BZ #25976, BZ #25824)Hans Dedecker2020-05-261-2/+2
| | | | | | | 3a44844c97 nss_compat: internal_end*ent may clobber errno, hiding ERANGE [BZ #25976] c839175267 aarch64: fix strcpy and strnlen for big-endian [BZ #25824] Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: create shared DTSI for DIR-810L and TEW-810DRAdrian Schmutzler2020-05-263-223/+118
| | | | | | | These devices seem to have the same board, so let's have a common file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-18 15:11:34 +0000