aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* glibc: update to 2.33Curtis Deptuck2021-02-091-3/+3
| | | | | | | | | | ChangeLog: https://sourceware.org/pipermail/libc-alpha/2021-February/122207.html Refresh patch: None required Signed-off-by: Curtis Deptuck <curtdept@me.com>
* ramips: add support for Cudy WR1300Andrew Pikler2021-02-092-0/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MediaTek MT7603E, MediaTek MT7612E - Switch: 1 WAN, 4 LAN (Gigabit) - Ports: 1 USB 3.0 - Buttons: Reset, WPS - LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB - Power: DC 12V 1A tip positive UART Serial: 115200 baud Located on unpopulated 4 pin header near J4: J4 [o] Rx [o] Tx [o] GND [ ] Vcc - Do not connect Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: - Loads only signed manufacture firmware due to bootloader RSA verification - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 - connect to any lan ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button for image to download - See http://www.cudytech.com/newsinfo/547425.html MAC addresses as verified by OEM firmware: use address source LAN *:f0 label WAN *:f1 label + 1 2g *:f0 label 5g *:f2 label + 2 The label MAC address is found in bdinfo 0xde00. Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
* ath79: add support for D-Link DAP-3662 A1Sebastian Schaper2021-02-097-5/+128
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * QCA9557, 16 MiB Flash, 128 MiB RAM, 802.11n 2T2R * QCA9882, 802.11ac 2T2R * 2x Gigabit LAN (1x 802.11af PoE) * IP68 pole-mountable outdoor case Installation: * Factory Web UI is at 192.168.0.50 login with 'admin' and blank password, flash factory.bin * Recovery Web UI is at 192.168.0.50 connect network cable, hold reset button during power-on and keep it pressed until uploading has started (only required when checksum is ok, e.g. for reverting back to oem firmware), flash factory.bin After flashing factory.bin, additional free space can be reclaimed by flashing sysupgrade.bin, since the factory image requires some padding to be accepted for upgrading via OEM Web UI. Both ethernet ports are set to LAN by default, matching the labelling on the case. However, since both GMAC Interfaces eth0 and eth1 are connected to the switch (QCA8337), the user may create an additional 'wan' interface as desired and override the vlan id settings to map br-lan / wan to either the PoE or non-PoE port, depending on the individual scenario of use. So, the LAN and WAN ports would then be connected to different GMACs, e.g. config interface 'lan' option ifname 'eth0.1' ... config interface 'wan' option ifname 'eth1.2' ... config switch_vlan option device 'switch0' option vlan '1' option ports '1 0t' config switch_vlan option device 'switch0' option vlan '2' option ports '2 6t' Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> [add configuration example] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for JCG Y2Chukun Pan2021-02-094-7/+152
| | | | | | | | | | | | | | | | | | | | | | | | JCG Y2 is an AC1300M router Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W25Q128JVSQ 16MiB RAM: Nanya NT5CB128M16 256MiB WLAN: 2.4/5 GHz 2T2R (1x MediaTek MT7615) Ethernet: 10/100/1000 Mbps x5 LED: POWER, INTERNET, 2.4G, 5G Button: Reset Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page. MAC addresses map: 0x0004 *:c8 wlan2g/wlan5g/label 0xe000 *:c7 lan 0xe006 *:c6 wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* uboot-envtools: Update to version 2021.01Hauke Mehrtens2021-02-081-2/+2
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tools: mkimage: Update U-Boot to version 2021.01Hauke Mehrtens2021-02-086-60/+13
| | | | | | | | | | | | * The fit image is now created with 0666 permission in upstream U-Boot remove our patch switch creates it with 0744 * The generated/autoconf.h file is created now as an empty file, it is not needed to remove this include any more. * Upstream lib/rsa/rsa-sign.c now includes stdlib.h instead of malloc.h * ALIGN_MASK was moved to imagetool.h, own patch should not be needed any more. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ltq-dsl-base: remove usused lantiq_dsl.shAndre Heider2021-02-082-750/+1
| | | | | | | All users have been converted to ubus. Signed-off-by: Andre Heider <a.heider@gmail.com> Tested-by: Martin Schiller <ms@dev.tdt.de>
* ltq-adsl-app: use ubus to provide metricsAndre Heider2021-02-082-4/+5
| | | | | | | | luci now uses ubus directly, so remove 'lucistat'. For manual usage just print the ubus output, use luci for a pretty version. Signed-off-by: Andre Heider <a.heider@gmail.com>
* ltq-vdsl-app: use ubus to provide metricsAndre Heider2021-02-082-4/+5
| | | | | | | | | luci now uses ubus directly, so remove 'lucistat'. For manual usage just print the ubus output, use luci for a pretty version. Signed-off-by: Andre Heider <a.heider@gmail.com> Tested-by: Martin Schiller <ms@dev.tdt.de>
* ltq-adsl-app: add ubus support to get metricsAndre Heider2021-02-082-1/+56
| | | | | | As with ltq-vdsl-app, see previous commit. Signed-off-by: Andre Heider <a.heider@gmail.com>
* ltq-vdsl-app: add ubus support to get metricsAndre Heider2021-02-083-1/+859
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a 'dsl' ubus object with a 'metrics' function to replace the expensive shell parsing done by /etc/init.d/dsl_control [dsl|luci]stat. All metrics are gathered by using syscalls. An additional thread is started to handle ubus events. $ time /etc/init.d/dsl_control dslstat real 0m 2.66s user 0m 0.90s sys 0m 1.76s $ time ubus call dsl metrics real 0m 0.02s user 0m 0.00s sys 0m 0.01s Example output: { "api_version": "4.17.18.6", "firmware_version": "5.8.1.5.0.7", "chipset": "Lantiq-VRX200", "driver_version": "1.5.17.6", "state": "Showtime with TC-Layer sync", "up": true, "uptime": 3891, "atu_c": { "vendor_id": [ 181, 0, 66, 68, 67, 77, 178, 26 ], "vendor": "Broadcom 178.26", "system_vendor_id": [ 181, 0, 66, 68, 67, 77, 0, 0 ], "system_vendor": "Broadcom", "version": [ 49, 57, 46, 48, 46, 51, 53, 46, 50, 32, 86, 69, 95, 49, 49, 95 ], "serial": [ 65, 65, 49, 52, 52, 54, 70, 69, 48, 90, 87, 45, 48, 56, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 ] }, "power_state": "L0 - Synchronized", "xtse": [ 0, 0, 0, 0, 0, 0, 0, 2 ], "annex": "B", "standard": "G.993.2", "profile": "17a", "mode": "G.993.2 (VDSL2, Profile 17a, with down- and upstream vectoring)", "upstream": { "vector": true, "trellis": true, "bitswap": true, "retx": true, "virtual_noise": false, "interleave_delay": 0, "data_rate": 31999000, "latn": 8.500000, "satn": 8.400000, "snr": 12.700000, "actps": -90.100000, "actatp": 13.400000, "attndr": 37180000 }, "downstream": { "vector": true, "trellis": true, "bitswap": true, "retx": true, "virtual_noise": false, "interleave_delay": 140, "data_rate": 89998000, "latn": 9.500000, "satn": 9.600000, "snr": 13.300000, "actps": -90.100000, "actatp": -1.600000, "attndr": 116315372 }, "errors": { "near": { "es": 1, "ses": 0, "loss": 3, "uas": 424, "lofs": 0, "fecs": 0, "hec": 0, "ibe": 0, "crc_p": 0, "crcp_p": 0, "cv_p": 0, "cvp_p": 0, "rx_corrupted": 27740, "rx_uncorrected_protected": 27010, "rx_retransmitted": 0, "rx_corrected": 730, "tx_retransmitted": 16222 }, "far": { "es": 242, "ses": 71, "loss": 0, "uas": 424, "lofs": 0, "fecs": 22687, "hec": 0, "ibe": 0, "crc_p": 0, "crcp_p": 0, "cv_p": 0, "cvp_p": 0, "rx_corrupted": 1383552, "rx_uncorrected_protected": 1220215, "rx_retransmitted": 0, "rx_corrected": 163337, "tx_retransmitted": 1574051 } } } Signed-off-by: Andre Heider <a.heider@gmail.com> Tested-by: Martin Schiller <ms@dev.tdt.de>
* ltq-vdsl-app: shutdown upon sigtermAndre Heider2021-02-082-2/+19
| | | | | | | | | | procd sends sigterm to stop daemons, hook it up. This speeds up the shutdown sequence and gets rid of the following message: daemon.info procd: Instance dsl_control::instance1 pid 15408 not stopped on SIGTERM, sending SIGKILL instead Signed-off-by: Andre Heider <a.heider@gmail.com> Tested-by: Martin Schiller <ms@dev.tdt.de>
* ath79: use internal switch for EAP300 v2Michael Pratt2021-02-083-21/+5
| | | | | | | | | | | | | | | | Have the port use GMAC1 with internal switch which fixes the issue of the ethernet LED not functioning The LED is triggered by the internal switch, not a GPIO. The GPIO for the ethernet LED was added in ath79 as it was defined in the ar71xx target but it was not functioning in ath79 for a previously unknown reason. It is unknown why that GPIO was defined as an LED in ar71xx. Signed-off-by: Michael Pratt <mcpratt@pm.me> [drop unrelated changes: model property and SPI max frequency] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: make all eth ports LAN for Engenius APsMichael Pratt2021-02-082-5/+4
| | | | | | | | | | | | | | | | | | for: - ENH202 v1 - ENS202EXT v1 - EnstationAC v1 - EWS511AP For EWS511AP, have default behavior as static ip to match the behavior of all other APs in ath79 These boards are sold as Client Bridge or Point to Point or Access Point so there is probably no benefit to have WAN by default for one of the ports, to prevent user confusion. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* kernel: bump 5.4 to 5.4.96John Audia2021-02-084-7/+7
| | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 Run-tested [*]: ramips/mt7621 (R6800, DIR-878 A1, EAP235-Wall) Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
* dnsmasq: Bump to v2.84Kevin Darbyshire-Bryant2021-02-083-3/+76
| | | | | | | | | | dnsmasq v2.84rc2 has been promoted to release. No functional difference between v2.83test3 and v2.84/v2.84rc2 Backport 2 patches to fix the version reporting Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* bcm4908: add board.d network setupRafał Miłecki2021-02-081-0/+26
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: add Ethernet driverRafał Miłecki2021-02-085-0/+1020
| | | | | | This commit picks up pending netdev patches. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* dnsmasq: switch to ubus-based hotplug callDaniel Golle2021-02-085-39/+46
| | | | | | | | Use new ubus-based hotplug call in dhcp-script.sh As sysntpd now makes use of the new ubus-based hotplug calls, dnsmasq no longer needs to ship ACL to cover ntpd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* busybox: sysntpd: make use of new ubus hotplug.ntp objectDaniel Golle2021-02-084-4/+28
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* procd: add hotplug-call dispatcher ubus objectsDaniel Golle2021-02-081-3/+3
| | | | | | Add per-subsystem ubus objects exposing hotplug-call. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* acx-mac80211: replace dead URLs with OpenWrt CDNIlya Lipnitskiy2021-02-071-9/+9
| | | | | | | | erley.org no longer exists; attempting to connect to it during package download results in lengthy timeouts. Use the new OpenWrt CDN alias to download from reliable OpenWrt mirrors. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: disable default build for HooToo HT-TM02Szabolcs Hubai2021-02-071-0/+1
| | | | | | | | | | | | | | | | | | While the latest version of 19.07 release is usable, the current master is unbootable on the device in a normal way. "Normal way" installations includes: - sysupgrade (e.g. from 19.07) - RESET button recovery with Ron Curry's (Wingspinner) UBoot image (10.10.10.3 + "Kernal.bin") - RESET button recovery with original U-Boot (10.10.10.254 + "kernel") One could flash and boot the latest master sysupgrade image successfully with serial access to the device. But a sysupgrade from this state still breaks the U-Boot and soft-bricks the device. Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
* ramips: mt7621: use preferred logic in lib/upgrade/iodata.shAdrian Schmutzler2021-02-071-3/+3
| | | | | | | shellcheck recommends || and && over "-a" and "-o" because the latter are not well defined. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for I-O DATA WN-DX1200GRINAGAKI Hiroshi2021-02-074-4/+222
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX1200GR is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : raw NAND 128 MiB - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7603E - 5 GHz : MediaTek MT7613BE - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LEDs/keys : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: 3.3V, TX, RX, NC, GND from triangle-mark - 57600n8 - Power : 12 VDC, 1 A Flash instruction using initramfs image: 1. Boot WN-DX1200GR normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with the squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - currently, mt7615e driver in mt76 doesn't fully support MT7613 (MT7663) wifi chip - the eeprom data in flash is not used by mt7615e driver and the driver reports the tx-power up to 3dBm - the correct MAC address for MT7613BE in eeprom data cannot be assigned to the phy - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" (called as "combo image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic ( 0x0 - 0x3 ) : 0x434F4D43 ("COMC") - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32" - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b) : kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs MAC addresses: LAN: 50:41:B9:xx:xx:08 (Ubootenv, ethaddr (text) / Factory, 0x1E000 (hex)) WAN: 50:41:B9:xx:xx:0A (Factory, 0x1E006 (hex)) 2.4GHz: 50:41:B9:xx:xx:08 (Factory, 0x4 (hex)) 5GHz: 50:41:B9:xx:xx:09 (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [add check whether dflag_offset is set] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: kernel: reenable the TRNGDaniel González Cabanelas2021-02-071-53/+2
| | | | | | | | | | | The hardware random number generator driver for bcm63xx was merged with the one used by the Raspberry Pi. Now this driver is lost. Reenable the HW_RANDOM kernel config with the new driver. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> [refresh kernel config] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mpc85xx: refresh kernel configPawel Dembicki2021-02-061-68/+16
| | | | | | Simple "make kernel_oldconfig" was done. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* treewide: unify OpenWrt hosted source via @OPENWRTPaul Spooren2021-02-0516-17/+19
| | | | | | | | | | | Multiple sources are hosted on OpenWrts source server only. The source URLs to point to the server vary based on different epochs in OpenWrts history. Replace all by @OPENWRT which is an "empty" mirror, therefore using the fallback servers sources.cdn.openwrt.org and sources.openwrt.org. Signed-off-by: Paul Spooren <mail@aparcar.org>
* kirkwood: use 3 temperature sensors for Zyxel NSA310BThomas Beckler2021-02-051-4/+16
| | | | | | | | | | | | | | | | | | | | Instead of taking the input of one temperature sensor (temp1), the script takes into account three temperature sensors to control the PWM of the cooling fan. temp1 -> placed on main board temp2 -> placed on main board temp3 -> placed on or close to chipset All three temperatures give valid input for the PWM of the fan on NSA310 and are actually changing. Tested on two NSA310. Signed-off-by: Thomas Beckler <thomas.beckler@hotmail.com> Reviewed-by: Alberto Bursi <bobafetthotmail@gmail.com> [commit title/message facelift, code cleanup] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tplink-safeloader: add support for TP-Link Archer A7 v5 (RU)Alexey Kunitskiy2021-02-051-1/+2
| | | | | | | | | | | | | | | | | | | Although provided in separate zip archives, the firmwares for EU and RU version are byte-identical. This adds the missing ID compared to the support-list in the vendor firmware. Note (since I checked it anyway): Partitions and support list are unchanged for all three existing firmware versions: * 20200721-rel40773 * 20201029-rel43238 * 20201120-rel50399 Signed-off-by: Alexey Kunitskiy <alexey.kv@gmail.com> [rewrite commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: wrap ucidef_add_switch in 02_networkAdrian Schmutzler2021-02-051-1/+2
| | | | | | Wrap line to be consistent with all other definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* build: move elx-header into image-commands.mkYanase Yuki2021-02-052-20/+20
| | | | | | | ELECOM WAB-I1750-PS will need this in ath79, so move it to common Makefile. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* kirkwood: refresh kernel configSungbo Eo2021-02-051-63/+2
| | | | | | Refresh config with make kernel_oldconfig. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* lantiq: change phy-mode to mii for FRITZ!Box 7412Aleksander Jan Bajkowski2021-02-051-1/+1
| | | | | | | | | | | FRITZ!Box 7412 loads the firmware for fast ethernet PHY and mii is more accurate in this case. Gmii is used by Gigabit ethernet PHYs. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> Reviewed-by: Mathias Kresin <dev@kresin.me> [minor commit title/message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: replace full-text BSC license by SPDX identifierAdrian Schmutzler2021-02-051-27/+1
| | | | | | | | | | This replaces a full-text BSD clause by the corresponding SPDX identifier. This should make it easier to identify the license both by humans and machines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: replace full-text licenses by SPDX identifierAdrian Schmutzler2021-02-0512-269/+12
| | | | | | | | | | This replaces several full-text and abbreviated licenses found in DTS files by the corresponding SPDX identifiers. This should make it easier to identify the license both by humans and machines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for UniElec U7621-01David Bentham2021-02-053-0/+174
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UniElec U7621-01 is a router platform board, the smaller model of the U7621-06. The device has the following specifications: - MT7621AT (880 MHz) - 256 of RAM (DDR3) - 16 MB of FLASH (SPI NOR) - 5x 1 Gbps Ethernet (MT7621 built-in switch) - 1x 2.4Ghz MT7603E - 1x 5Ghz MT7612 - 1x miniPCIe slots (PCIe bus only) - 1x miniSIM slot - 1x USB 2.0 (uses the usb 3.0 driver) - 8x LEDs (1x GPIO-controlled) - 1x reset button - 1x UART header (4-pins) - 1x GPIO header (30-pins) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - 1x 2.4Ghz MT7603E (wifi) - 1x 5Ghz MT7612 (wifi) - miniPCIe slots (tested with Wi-Fi cards and LTE modem cards) - miniSIM slot (works with normal size simcard) - sysupgrade - reset button Installation: This board has no locked down bootloader. The seller can be asked to install openwrt v18.06, so upgrades are standard sysupgrade method. Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. LEDs list (left to right): - ESW_P0_LED_0 - ESW_P1_LED_0 - ESW_P2_LED_0 - ESW_P3_LED_0 - ESW_P4_LED_0 - CTS2_N (GPIO10, configured as "status" LED) - LED_WLAN# (connected with pin 44 in wifi1 slot) Signed-off-by: David Bentham <db260179@gmail.com> [add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Meraki MR12Martin Kennedy2021-02-057-9/+209
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Port device support for Meraki MR12 from the ar71xx target to ath79. Specifications: - SoC: AR7242-AH1A CPU - RAM: 64MiB (NANYA NT5DS32M16DS-5T) - NOR Flash: 16MiB (MXIC MX25L12845EMI-10G) - Ethernet: 1 x PoE Gigabit Ethernet Port (SoC MAC + AR8021-BL1E PHY) - Ethernet: 1 x 100Mbit port (SoC MAC+PHY) - Wi-Fi: Atheros AR9283-AL1A (2T2R, 11n) Installation: 1. Requires TFTP server at 192.168.1.101, w/ initramfs & sysupgrade .bins 2. Open shell case 3. Connect a USB->TTL cable to headers furthest from the RF shield 4. Power on the router; connect to U-boot over 115200-baud connection 5. Interrupt U-boot process to boot Openwrt by running: setenv bootcmd bootm 0xbf0a0000; saveenv; tftpboot 0c00000 <filename-of-initramfs-kernel>.bin; bootm 0c00000; 6. Copy sysupgrade image to /tmp on MR12 7. sysupgrade /tmp/<filename-of-sysupgrade>.bin Notes: - kmod-owl-loader is still required to load the ART partition into the driver. - The manner of storing MAC addresses is updated from ar71xx; it is at 0x66 of the 'config' partition, where it was discovered that the OEM firmware stores it. This is set as read-only. If you are migrating from ar71xx and used the method mentioned above to upgrade, use kmod-mtd-rw or UCI to add the MAC back in. One more method for doing this is described below. - Migrating directly from ar71xx has not been thoroughly tested, but one method has been used a couple of times with good success, migrating 18.06.2 to a full image produced as of this commit. Please note that these instructions are only for experienced users, and/or those still able to open their device up to flash it via the serial headers should anything go wrong. 1) Install kmod-mtd-rw and uboot-envtools 2) Run `insmod mtd-rw.ko i_want_a_brick=1` 3) Modify /etc/fw_env.config to point to the u-boot-env partition. The file /etc/fw_env.config should contain: # MTD device env offset env size sector size /dev/mtd1 0x00000 0x10000 0x10000 See https://openwrt.org/docs/techref/bootloader/uboot.config for more details. 4) Run `fw_printenv` to verify everything is correct, as per the link above. 5) Run `fw_setenv bootcmd bootm 0xbf0a0000` to set a new boot address. 6) Manually modify /lib/upgrade/common.sh's get_image function: Change ... cat "$from" 2>/dev/null | $cmd ... into ... ( dd if=/dev/zero bs=1 count=$((0x66)) ; # Pad the first 102 bytes echo -ne '\x00\x18\x0a\x12\x34\x56' ; # Add in MAC address dd if=/dev/zero bs=1 count=$((0x20000-0x66-0x6)) ; # Pad the rest cat "$from" 2>/dev/null ) | $cmd ... which, during the upgrade process, will pad the image by 128K of zeroes-plus-MAC-address, in order for the ar71xx's firmware partition -- which starts at 0xbf080000 -- to be instead aligned with the ath79 firmware partition, which starts 128K later at 0xbf0a0000. 7) Copy the sysupgrade image into /tmp, as above 8) Run `sysupgrade -F /tmp/<sysupgrade>.bin`, then wait Again, this may BRICK YOUR DEVICE, so make *sure* to have your serial cable handy. Signed-off-by: Martin Kennedy <hurricos@gmail.com> [add LED migration and extend compat message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Hi-Link HLK-7688AEwan Parker2021-02-054-0/+128
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7688AN - RAM: 128 MB - Flash: 32 MB - Ethernet: 5x 10/100 (1x WAN, 4x LAN) - Wireless: built in 2.4GHz (bgn) - USB: 1x USB 2.0 port - Buttons: 1x Reset - LEDs: 1x (WiFi) Flash instructions: - Configure TFTP server with IP address 10.10.10.3 - Name the firmware file as firmware.bin - Connect any Ethernet port to the TFTP server's LAN - Choose option 2 in U-Boot - Alternatively choose option 7 to upload firmware to the built-in web server MAC addresses as verified by OEM firmware: use address source 2g *:XX factory 0x4 LAN *:XX+1 factory 0x28 WAN *:XX+1 factory 0x2e Notes: This board is ostensibly a module containing the MediaTek MT7688AN SoC, 128 MB DDR2 SDRAM and 32 MB flash storage. The SoC can be operated in IoT Gateway Mode or IoT Device Mode. From some vendors the U-Boot that comes installed operates on UART 2 which is inaccessible in gateway mode and operates unreliably in the Linux kernel when using more than 64 MB of RAM. For those, updating U-Boot is recommended. Signed-off-by: Ewan Parker <ewan@ewan.cc> [add WLAN to 01_leds] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* build: use SPDX license tagsPaul Spooren2021-02-0538-175/+72
| | | | | | | | | The license folder is a core part of OpenWrt and all GPL-2.0 licensed. Use SPDX license tags to allow machines to check licenses. Signed-off-by: Paul Spooren <mail@aparcar.org> [rebase, keep some Copyright lines, sharpen commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* selinux-policy: update to version 0.6Daniel Golle2021-02-051-2/+2
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: add defaults for new SELinux optionsDaniel Golle2021-02-051-0/+10
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.4 to 5.4.95John Audia2021-02-043-40/+3
| | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Removed upstreamed patches: imx6: 303-ARM-dts-imx6qdl-gw52xx-fix-duplicate-regulator-namin.patch Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* hostapd: add forgotten patch for P2P vulnerability fixPetr Štetiar2021-02-042-1/+39
| | | | | | | | Commit 7c8c4f1be648 ("hostapd: fix P2P group information processing vulnerability") was missing the actual patch for the vulnerability. Fixes: 7c8c4f1be648 ("hostapd: fix P2P group information processing vulnerability") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* hostapd: fix P2P group information processing vulnerabilityDaniel Golle2021-02-041-1/+1
| | | | | | | | | | | A vulnerability was discovered in how wpa_supplicant processing P2P (Wi-Fi Direct) group information from active group owners. This issue was discovered by fuzz testing of wpa_supplicant by Google's OSS-Fuzz. https://w1.fi/security/2020-2/wpa_supplicant-p2p-group-info-processing-vulnerability.txt Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* trusted-firmware-a.mk: add PKG_CPE_IDDaniel Golle2021-02-041-0/+1
| | | | | | | Vulnerabilities of Trusted Firmware A are tracked as cpe:/a:arm:arm_trusted_firmware Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: make use of trusted-firmware-a.mkDaniel Golle2021-02-031-10/+6
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* tfa-layerscape: don't build fiptoolDaniel Golle2021-02-031-8/+3
| | | | | | tfa-fiptool is now provided by an extra package. Use that instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-tools: add packageDaniel Golle2021-02-031-0/+70
| | | | | | | Package ARM Trusted Firmware host tools separately. (instead of building tfa-fiptool as part of tfa-layerscape) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* iptables: update to 1.8.7Curtis Deptuck2021-02-021-2/+2
| | | | | | | | | | ChangeLog: https://netfilter.org/projects/iptables/files/changes-iptables-1.8.7.txt Refresh patch: None required Signed-off-by: Curtis Deptuck <curtdept@me.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-29 06:15:26 +0000