aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* layerscape: split up DEVICE_TITLE definitionsMoritz Warning2019-09-252-13/+35
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
* gemini: dir685: Restore graphicsLinus Walleij2019-09-252-14/+6
| | | | | | | | | | | | | | | One of the v4.19 patches had a bug, this is fixed upstream, but in OpenWrt we can fix it by just fixing the bug in the patch. We also need to augment the config file to select the CONFIG_DRM_FBDEV_EMULATION symbol. This restores the display controller on the DIR-685 to working state: penguin and graphics on the little screen with default OpenWrt install. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* kernel: update and fix xt_FLOWOFFLOAD target on 4.19Felix Fietkau2019-09-251-13/+25
| | | | | | | Merge upstream changes to nft_flow_offload. Fixes offloading Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/coreutils: install "touch"Felix Fietkau2019-09-251-1/+1
| | | | | | | Fixes error in setting SOURCE_DATE_EPOCH timestamp on files on rootfs prepare on non-Linux systems Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: initialize youhua, wr1200js WAN MAC addresses from flashAdrian Schmutzler2019-09-251-0/+1
| | | | | | | | | This patch changes wan MAC address setup for youhua,wr1200js from retrieving it by calculation to reading it from flash. This has been checked on-device. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for I-O DATA WNPR2600GINAGAKI Hiroshi2019-09-253-0/+183
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WNPR2600G is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7615 - 5 GHz : MediaTek MT7615 - Ethernet : 10/100/1000 Mbps - Switch : MT7530 (SoC) - LED/keys : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, RX, GND, TX from SoC side - 57600n8 Flash instruction using factory image: 1. Boot WNPR2600G normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: move "elx-header" to Makefile from mt7620.mk and mt7621.mkINAGAKI Hiroshi2019-09-253-38/+20
| | | | | | | | | | | I-O DATA WNPR2600G has an "elx-header", so move this definition to generic makefile to use it from mt7621 subtarget. This definition is also added to mt7621.mk in f285e8634c57d28aa970b80c5c59e85485f35c7d, so remove it from mt7621.mk. And added a line to cleanup used header file. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: replace MAC address configuration for I-O DATA WN-AC-GR devicesINAGAKI Hiroshi2019-09-251-1/+1
| | | | | | | | | | | | | following I-O DATA devices have a MAC address as "wanaddr" for WAN interface in u-boot-env: - WN-AC1167GR - WN-AC733GR3 I replaced MAC address configuration in these devices to omit address calculation in 02_network. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for ipTIME A3Sungbo Eo2019-09-255-92/+161
| | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek MT7628AN. Specifications: - SoC: MT7628AN - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7612EN - Ethernet: 3x 10/100Mbps - Switch: SoC internal - UART: - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for XiaoYu XY-C5Qi Jiang2019-09-253-0/+114
| | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621A Flash: 32 MiB RAM: 512 MiB Ethernet: built-in switch USB: 1x USB3.0 SATA: ASM1060, 1 SATA port Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.173.22 2. Download *-sysupgrade.bin image and rename it to firmware.img 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Turn on router,press the reset button and wait ~15 seconds 6. Release the reset button and after a short time the firmware should be transferred from the tftp server 7. Wait ~3 minutes to complete recovery. Signed-off-by: Qi Jiang <rushx@live.cn> [squash commits, add label-mac-device, fix sign-off style] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: bump 4.19 to 4.19.75Koen Vandeputte2019-09-245-7/+7
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14814 - CVE-2019-14815 - CVE-2019-14816 - CVE-2019-14821 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.146Koen Vandeputte2019-09-242-3/+3
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14814 - CVE-2019-14815 - CVE-2019-14816 - CVE-2019-14821 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.194Koen Vandeputte2019-09-247-12/+12
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14814 - CVE-2019-14815 - CVE-2019-14816 - CVE-2019-14821 Compile-tested on: none Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* iwinfo: update to latest Git HEADJo-Philipp Wich2019-09-221-3/+3
| | | | | | | | 313e827 nl80211: keep awaiting wpa_supplicant scan results on busy response a766751 nl80211: fix parsing of mixed wpa encryption in wpa_supp scan results f096bfd utils: support parsing SAE and OWE key management suites from IEs Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ath79: convert devices to interrupt-driven gpio-keysAdrian Schmutzler2019-09-2247-94/+51
| | | | | | | | | | | | | This converts all remaining devices to use interrupt-driven gpio-keys compatible instead of gpio-keys-polled. The poll-interval is removed. Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as this one is using ath9k keys. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Karl Palsson <karlp@etactica.com> Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
* hostapd: Add mesh support for wpad fullHauke Mehrtens2019-09-221-2/+2
| | | | | | | | | | | | | | This increases the size of the binary slightly: old: 427722 wpad-wolfssl_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk 431696 wpad-openssl_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk new: 442109 wpad-wolfssl_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk 445997 wpad-openssl_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* hostapd: use getrandom syscallHauke Mehrtens2019-09-227-7/+7
| | | | | | | | hostapd will not use the getrandom() syscall and as a fallback use /dev/random, the syscall is supported since Linux 3.17 and in the musl, glibc and uclibc version used by OpenWrt. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* hostapd: Remove unneeded patchHauke Mehrtens2019-09-228-28/+14
| | | | | | | All the content of this function is proceeded by IEEE8021X_EAPOL no code accesses the ssid variable outside of this ifdef. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* hostapd: use config option CONFIG_NO_LINUX_PACKET_SOCKET_WARHauke Mehrtens2019-09-225-16/+4
| | | | | | Instead of patching the workaround away, just use the config option. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* hostapd: Update to version 2.9 (2019-08-08)Hauke Mehrtens2019-09-2247-639/+272
| | | | | | | | | | | | | | | | | | The size of the ipkgs increase a bit (between 0.7% and 1.1%): old 2019-04-21 (2.8): 288264 wpad-basic_2019-04-21-63962824-1_mipsel_24kc.ipk 256188 wpad-mini_2019-04-21-63962824-1_mipsel_24kc.ipk 427475 wpad-openssl_2019-04-21-63962824-1_mipsel_24kc.ipk 423071 wpad-wolfssl_2019-04-21-63962824-1_mipsel_24kc.ipk new 2019-08-08 (2.9): 290217 wpad-basic_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk 258745 wpad-mini_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk 431732 wpad-openssl_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk 427641 wpad-wolfssl_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* hostapd: Update to version 2.8 (2019-04-21)Hauke Mehrtens2019-09-2289-5673/+532
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This also syncs the configuration files with the default configuration files, but no extra options are activated or deactivated. The mesh patches were partially merged into hostapd 2.8, the remaining patches were extracted from patchwork and are now applied by OpenWrt. The patches still have open questions which are not fixed by the author. They were taken from this page: https://patchwork.ozlabs.org/project/hostap/list/?series=62725&state=* The changes in 007-mesh-apply-channel-attributes-before-running-Mesh.patch where first applied to hostapd, but later reverted in hostapd commit 3e949655ccc5 because they caused memory leaks. The size of the ipkgs increase a bit (between 1.3% and 2.3%): old 2018-12-02 (2.7): 283337 wpad-basic_2018-12-02-c2c6c01b-11_mipsel_24kc.ipk 252857 wpad-mini_2018-12-02-c2c6c01b-11_mipsel_24kc.ipk 417473 wpad-openssl_2018-12-02-c2c6c01b-11_mipsel_24kc.ipk 415105 wpad-wolfssl_2018-12-02-c2c6c01b-11_mipsel_24kc.ipk new 2019-04-21 (2.8): 288264 wpad-basic_2019-04-21-63962824-1_mipsel_24kc.ipk 256188 wpad-mini_2019-04-21-63962824-1_mipsel_24kc.ipk 427475 wpad-openssl_2019-04-21-63962824-1_mipsel_24kc.ipk 423071 wpad-wolfssl_2019-04-21-63962824-1_mipsel_24kc.ipk Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* apm821xx: remove unnecessary kernel paddingRussell Senior2019-09-211-2/+1
| | | | | | | | | | | | | | | | | | The allocation of LEBs to ubi volumes is handled by the sysupgrade script: package/base-files/files/lib/upgrade/nand.sh and the ubimkvol and or ubirsvol command. Therefore, padding of the kernel blob is not needed at all, so use cat instead of dd. The BLOCKSIZE variable was only used in the dd command. In any case, 63k made no sense for the way BLOCKSIZE was being used. 63k (64512) does make sense for DTB_SIZE because of the offsets expected by u-boot given extant u-boot-env variables. Tested on Meraki MR24. Signed-off-by: Russell Senior <russell@personaltelco.net>
* ath79: add support of Netgear WNDR3800CHDmitry Tunin2019-09-214-3/+53
| | | | | | | | Add support for the ar71xx supported Netgear WNDR3800CH to ath79. The device is identical to WNDR3800 except NETGEAR_BOARD_ID. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: DIR825B1 switch to gpio-keysDmitry Tunin2019-09-211-4/+1
| | | | Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ipq40xx: fix hw-crypto detection of qce driverEneas U de Queiroz2019-09-212-0/+62
| | | | | | | | | | This adds the CRYPTO_ALG_KERN_DRIVER_ONLY flag to Qualcomm crypto engine driver algorithms, so that openssl devcrypto can recognize them as hardware-accelerated. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> [refresh, move to ipq40xx as its the only target right now] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: remove invalid uses of ath9k_patch_fw_mac_crcAdrian Schmutzler2019-09-211-3/+3
| | | | | | | | | | | | Some ar9344-based devices are using ath9k_patch_fw_mac_crc, which is meant to generate a checksum, for fixing their ath9k MAC addresses. However, those do not have a checksum field, and the calculated checksum offset would be negative. This patch will use ath9k_patch_fw_mac function for those devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: replace backticks by $(...)Adrian Schmutzler2019-09-212-4/+4
| | | | | | | | | This replaces deprecated backticks by more versatile $(...) syntax. While at it, remove some useless cat commands and deprecated egrep commands. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: image: pad kernel for Adtran/Bluesocket devicesTomasz Maciej Nowak2019-09-211-2/+2
| | | | | | | | | | | | | | | | It has been reported that using the sysupgrade-tar image will trigger "lzma_decode failed error". The RedBoot bootloader always loads data from flash till block size boundary, so if there's no padding it'll also load the beginning of rootfs, and it seems that lzma_decoder can't handle that garbage data. Previously the script creating combined-image silently padded the kernel and rootfs, but since sysupgrade-tar doesn't, pad the default kernel image. Fixes: 900330f ("ath79: image: retire combined-image for Adtran/Bluesocket devices") Cc: Brian Gonyer <bgonyer@gmail.com> Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: sort device definitions in image/*Adrian Schmutzler2019-09-216-303/+301
| | | | | | | | | | | This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ltq-vdsl-fw: update firmware filename and download URLDaniel Golle2019-09-213-5/+5
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* rpcd: update to latest Git HEADJo-Philipp Wich2019-09-211-3/+3
| | | | | | 95f0973 file: increase minimum read buffer size to 4096 bytes Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* build: set TARGET_ROOTFS_PARTSIZE to make combined image fit in 128MBMatthias Schiffer2019-09-211-1/+1
| | | | | | | | | | | | Change TARGET_ROOTFS_PARTSIZE from 128 to 104 MiB, so the whole image (bootloader + boot + root) will fit on a 128MB CF card by default. With these settings, the generated images (tested on x86-generic and x86-64) have 126,353,408 bytes; the smallest CF card marketed as "128MB" that I found a datasheet for (a Transcend TS128MCF80) has 126,959,616 bytes. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* rootfs.mk: ensure all timestamp are set to SOURCE_DATE_EPOCHAlexander Couzens2019-09-211-0/+1
| | | | | | | | Some tools doesn't support SOURCE_DATE_EPOCH (e.g. initramfs images). Ensure all files of a root filesystem are set to SOURCE_DATE_EPOCH. Make initramfs builds reproducible (for ramips). Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* usign: update to latest Git HEADHauke Mehrtens2019-09-211-3/+3
| | | | | | f34a383 main: fix some resource leaks Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* fstools: update to latest Git HEADHauke Mehrtens2019-09-211-3/+3
| | | | | | | | 4327ed4 mkdev: Avoid out of bounds read 9b3eb63 libblkid-tiny: use blkid_probe_set_utf8label for label set c9d0462 libblkid-tiny: adds blkid_probe_set_utf8label support Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* procd: update to the latest git HEADHauke Mehrtens2019-09-211-3/+3
| | | | | | | 8e9fb51 procd: Switch to nanosleep c844ace system: Fix possible integer overflows Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* hostapd: Fix AP mode PMF disconnection protection bypassHauke Mehrtens2019-09-214-6/+72
| | | | | | | | This fixes * CVE-2019-16275 AP mode PMF disconnection protection bypass https://w1.fi/security/2019-7/ap-mode-pmf-disconnection-protection-bypass.txt Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: Add support for Banana Pi M2 UltraHal Martin2019-09-215-2/+45
| | | | | | | | | | | | | | | | | | CPU: Allwinner R40 Quad-Core Cortex-A7 @ 1.2GHz GPU: Mali 400 MP2 Memory: 2GB DDR3 onboard (shared with GPU) Onboard: Storage microSD card slot Onboard: Storage 8GB eMMC Onboard: Network 10/100/1000M Ethernet RJ45 Onboard: Network WiFi 802.11b/g/n 1x1 (AMPAK AP6212; brcmfmac) Onboard header: SPI, I2C, GPIO, UART USB: Two USB 2.0 Host, One USB 2.0 OTG Known issues: - WiFi doesn't work - eMMC not supported Signed-off-by: Hal Martin <hal.martin@gmail.com>
* elfutils: Add host buildRosen Penev2019-09-212-16/+9
| | | | | | | | | | | | | | | | | | | | | | | Needed for glib2 host build: gresource-tool.c:32:20: fatal error: libelf.h: No such file or directory #include <libelf.h> Changed PKG_LICENSE to the SPDX version. Switched build dependency for argp-standalone to !USE_GLIBC. argp is a glibc extension. Treat it as such. Adjusted patch to use strerror_l, which works properly with both glibc and musl. The patch errors under glibc with: dwfl_error.c:158:7: error: ignoring return value of 'strerror_r', declared with attribute warn_unused_result [-Werror=unused-result] strerror_r (error & 0xffff, s, sizeof(s)); void casting does not fix the error. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* at91:sam9x: create sdcard imagesSandeep Sheriker M2019-09-211-2/+42
| | | | | | create sdcard images for sam9x25 & sam9x35 ek targets. Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* at91:sama5: create fit imageSandeep Sheriker M2019-09-212-1/+5
| | | | | | | create fit image & add it to sdcard image for sama5 target device. Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
* wolfssl: allow building with hw-crytpo and AES-CCMEneas U de Queiroz2019-09-204-21/+160
| | | | | | | | Hardware acceleration was disabled when AES-CCM was selected as a workaround for a build failure. This applies a couple of upstream patches fixing this. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* mbedtls: update to 2.16.3Magnus Kroken2019-09-203-52/+25
| | | | | | | Remove 300-bn_mul.h-Use-optimized-MULADDC-code-only-on-ARM-6.patch, the issue has been fixed upstream. Signed-off-by: Magnus Kroken <mkroken@gmail.com>
* uClibc++: Remove faulty patchRosen Penev2019-09-202-14/+1
| | | | | | | | | | | | | | | This patch was originally added to fix compilation with v4l2rtspserver. Turns out it was v4l2rtspserver that was broken, not uClibc++. This now causes issues with a different package where the arguments are being split. Note that with this patch, shellcheck throws an error: SC2068: Double quote array expansions to avoid re-splitting elements. More: https://github.com/openwrt/packages/pull/9972#discussion_r324878373 Signed-off-by: Rosen Penev <rosenp@gmail.com>
* gcc: Fix ICE in GCC 9.2.0Hauke Mehrtens2019-09-201-0/+55
| | | | | | | | This backports a fix from GCC master to fix a internal compiler exception seen when compiling libjson-c with mips16 activated. Fixes: FS#2455 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.19 to 4.19.74Koen Vandeputte2019-09-209-14/+12
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-15504 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.145Koen Vandeputte2019-09-2011-24/+24
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* iwinfo: update to latest Git HEADJo-Philipp Wich2019-09-201-3/+3
| | | | | | | | | 02112f9 cli: fix reporting of mixed WPA2/WPA3 versions 7faeaea nl80211: properly detect WEP encryption in wpa_supp scan results 629b5ff nl80211: do not confuse open connections with WEP ones 3d47ddd nl80211: rework hostapd and wpa_supplicant wpa suite parsing Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* hostapd: mirror ieee80211w ap mode defaults in station modeJo-Philipp Wich2019-09-202-1/+10
| | | | | | | | | | | For AP mode, OpenWrt automatically sets ieee80211w to either 1 or 2, depending on whether the encryption is set to sae-mixed, or sae/owe/eap suite-b. Mirror the same defaults for client mode connections, in order to allow an OpenWrt station to associate to an OpenWrt ap with SAE, OWE or Suite-B encryption without the need to manually specify "option ieee80211w" on the station. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* hostapd: fix OWE settings in client modeJo-Philipp Wich2019-09-202-1/+2
| | | | | | | | This changes fixes the generation of the wpa_supplicant client configuration in WPA3 OWE client mode. Instead of incorrectly emitting key_mgmt=NONE, use the proper key_mgmt=OWE setting instead. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-30 13:35:39 +0000