aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mpc85xx: tl-wdr4900-v1: convert to mtdsplit imagePawel Dembicki2019-01-053-52/+62
| | | | | | | | | | | | | | | Currently, the image creation process for the TP-Link tl-wdr4900-v1 needs a fixed sized kernel and places the rootfs partition at a fixed offset. With the upcoming move to 4.19 the kernel will no longer fit into the existing allocated space for the kernel partition. This patch converts the device to utilize the established tplink,firmware mtdsplitter, which can deal with a dynamic kernel/rootfs size. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* ath79: add support for devolo WiFi pro 1200iDavid Bauer2019-01-054-0/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for devolo WiFi pro 1750iDavid Bauer2019-01-054-1/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: cleanup the RB750Gr3 supportAnton Arapov2019-01-053-24/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | Always enable the pwr led and use the usr led for boot status indication. Rename nodes in the dts, to match what is recommend in the devicetree specification. Increase the maximum spi frequency to 20MHz and drop the m25p,chunked-io which isn't required on mt7621. Use the BTN_0 keycode for the mode button. This board doesn't have any wireless. Use a more descriptive label for the reset button and the GPIO enabling the usb vcc supply. Use the beeper kernel module for the buzzer. Fix the pinmux to switch only pins used as GPIOs to the GPIO function. Add support for the PoE enable GPIO to the userspace. The PoE power status can be read via GPIO7. Since OpenWrt doesn't have support for reading inputs from userspace, prepare only the pinmux for the GPIO. Signed-off-by: Anton Arapov <arapov@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add RB750Gr3 native supportAnton Arapov2019-01-055-31/+48
| | | | | | | | | | | | | | | | | This patch adds support of MikroTik RouterBOARD 750Gr3, without the need to reflashing the bootloader. Installation through RouterBoot follows the usual MikroTik method https://openwrt.org/toh/mikrotik/common Since the image isn't compatible with RouterBOARD 750Gr3 installations which have replaced the bootloader, the former used userspace boardname is not added to the SUPPORTED_DEVICES, to prevent a brick while trying to upgrade to the image with native support. Signed-off-by: Anton Arapov <arapov@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Mathias Kresin <dev@kresin.me>
* busybox: Add ALTERNATIVES for findutilsDaniel F. Dickinson2019-01-031-1/+3
| | | | | | | | | | | | Currently busybox find and xargs conflict with the versions from findutils package. Fix this by using ALTERNATIVES in busybox and the related findutils (from packages feed) commit. The conflict is due to the binaries being in the the same place in rootfs and opkg not being happy about that. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
* kernel: Fix kmod-w1 dependency on hwmon-core for 4.19Petr Štetiar2019-01-031-1/+1
| | | | | | kmod-w1 depends on kmod-hwmon-core since Linux 4.14 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: Fix rtc-ds1307 dependency on hwmon-core for 4.19Petr Štetiar2019-01-031-1/+1
| | | | | | | | | | | | | | | | | | | | It seems, that since Linux 4.18-rc1 rtc-ds1307 depends on hwmon-core. commit 6b583a64fd1e019fd01626b46892ebf2361951c5 Author: Heiner Kallweit <hkallweit1@gmail.com> Date: Wed Sep 27 22:41:26 2017 +0200 rtc: ds1307: simplify hwmon config We don't have to define an extra config symbol, IS_REACHABLE does what we need. And having this config symbol just to save the few bytes of hwmon support on non-DS3231 chips isn't worth it IMO (especially as the symbol is set per default). While at it, use the same dependency check for `kmod-regmap` as well, so it's future proof as well. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firewall: update to latest git HEADHans Dedecker2019-01-031-3/+3
| | | | | | | | 70f8785 zones: add zone identifying local traffic in raw OUTPUT chain 6920de7 utils: Free args in __fw3_command_pipe() 6ba9105 options: redirects: Fix possible buffer overflows Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath79: merge cases in 02_networkPaul Wassi2019-01-021-16/+6
| | | | | | Merge some duplicate cases in /etc/board.d/02_network Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* build: Drop user/group ID/name from sysupgrade.tarSven Eckelmann2019-01-021-1/+1
| | | | | | | | | Tar will automatically record the user/group ID and name for files/directories. This reduces the reproducibility of the sysupgrade.tar because most of the people don't use the same username as the OpenWrt buildserver. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* build: Use stable file ordering in sysupgrade.tarSven Eckelmann2019-01-021-1/+1
| | | | | | | | | | | | | The file ordering in the current sysupgrade depends on the order of file in a filesystem. This is often already in a sane (alphabetical order) but this is not always the case. For example, the OpenWrt build servers return a different ordering. This breaks the reproducibility of the sysupgrade tarballs significantly and also resulted in images which cannot be used for upgrades on devices like the OpenMesh A42/A62. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* uboot-envtools: Add domywifi dw33d supportshanpo2019-01-021-0/+1
| | | | Signed-off-by: shanpo <jwdsccd@gmail.com>
* uboot-envtools: ipq40xx: Configuration for GL.iNet GL-B1300Ibrahim Tachijian2019-01-021-0/+1
| | | | | | This commit adds the nescessary settings to allow reading the uboot environment variables on the GL.iNet GL-B1300 board. Signed-off-by: Ibrahim Tachijian <barhom@netsat.se>
* x86: enable kmod-bnx2 on 64-bit by defaultAlberto Bursi2019-01-021-1/+1
| | | | | | | Gigabit ethernet adapters using BCM5706/5708/5709/5716 chipset are common on servers and as easy/cheap to get as Intel based ones. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kernel: mtd: add support for EN25QH64 in spi-nor.cRoger Pueyo Centelles2019-01-022-0/+20
| | | | | | | | | | The Eon EN25QH64 is a 64 Mbit SPI NOR flash memory chip. Its 32, 128 and 256 Mbits siblings are supported upstream but this particular size wasn't. This commit includes patches for kernels 4.14 and 4.19. Tested on a COMFAST CF-E120A v3 (ath79). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* hostapd: update to version 2018-12-02 (2.7)Hauke Mehrtens2019-01-0238-429/+169
| | | | | | | | | | This updates hostapd to version the git version from 2018-12-02 which matches the 2.7 release. The removed patches were are already available in the upstream code, one additional backport is needed to fix a compile problem. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* fstools: update to the latest master branchRafał Miłecki2019-01-021-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a big block(d) cleanup with new feature of generating "mount" hotplug.d events. It's an important update for those who were using mountd in the pre-18.06 releases. Due to the mountd being replaced with blockd a support for "mountd" hotplug.d events has been lost. It broke all kind of shell scripts that were e.g. managing services depending on an external USB drive availability. This basically (re-)adds support for calling /etc/hotplug.d/mount/ scripts with ACTION ("add" or "remove") and DEVICE set. af93f4b block(d): improve hotplug.d "mount" events for the autofs 3bb3352 blockd: unmount device explicitly when it disappears 28753b3 block: remove target directory after unmounting c8c7ca5 block: cleanup handling "start" action of the "autofs" command f1bb762 block: make blockd_notify() return an int instead of void 71c2bde block: generate hotplug.d mount events 30f5096 block: validate amount of arguments for the "autofs" command dc6a462 blockd: don't reparse blob msg in the vlist callbacks f6a9686 blockd: don't unmount device when removing it from the list 1913fea block: don't duplicate unmounting code in the mount_action() 6b445fa block: make umount_device() function more generic a778468 block: don't duplicate mounting code in the mount_device() 5dc631d block: simplify code picking mount target directory 2971779 block: move blockd_notify() call out of the conditional blocks b86bd6e block: fix formatting & indent in the mount_device() e12c0d6 fstools: use EXIT_FAILURE when indicating error on exit 091aa3d fstools: guard usage of WEXITSTATUS Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* glibc: update to latest 2.27 commit (BZ #24027, BZ #23927)Hans Dedecker2019-01-011-2/+2
| | | | | | | | | | | | | | | | 3981fc3453 malloc: Always call memcpy in _int_realloc [BZ #24027] f6d0e8c36f Fix rwlock stall with PREFER_WRITER_NONRECURSIVE_NP (bug 23861) 2794474c65 powerpc: Add missing CFI register information (bug #23614) d8ca7a0c71 Fix _dl_profile_fixup data-dependency issue (Bug 23690) f1e211096b inet/tst-if_index-long: New test case for CVE-2018-19591 [BZ #23927] 4e9f34e54f support: Implement <support/descriptors.h> to track file descriptors e75481a7a7 support: Close original descriptors in support_capture_subprocess 0f79dc0be3 support_quote_string: Do not use str parameter name 6b2dd53aa0 support: Implement support_quote_string 50477165b9 malloc: Add another test for tcache double free check. 4b246928bd malloc: tcache double free check Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath79: align GL-AR750S boardname to other GL.iNet devicesChristoph Krapp2019-01-014-10/+7
| | | | | | As the official device name is GL-AR750S, rename the board accordingly. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* apm821xx: sata: boot-part feature integrationChristian Lamparter2019-01-013-4/+6
| | | | | | | | | | | | This patch adds the boot-part feature to the apm82181 sata target. This makes it possible to configure the boot partition size with the generic CONFIG_TARGET_KERNEL_PARTSIZE symbol. Please note: For people using custom images: Just like with CONFIG_TARGET_ROOTFS_PARTSIZE changing the value can cause sysupgrade to repartition the device! Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: use bin file extension for sysupgrade-tar imagesChristian Lamparter2019-01-011-8/+8
| | | | | | | Use the file extension bin for sysupgrade-tar images with metadata to unify the file extension across the target/tree. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: utilize build ARTIFACTsChristian Lamparter2019-01-011-3/+5
| | | | | | | | | | | The exported kernel dtbs can be build as artifacts. This way, the MyBook Live's DTB is not generated twice. While at it, give the artifacts their proper name. For the wndr4700 use the "device-tree" partition name and for the MyBook Live: "apollo3g.dtb" to match the mbl_boot.scr. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq806x: add support for Buffalo WXR-2533DHPINAGAKI Hiroshi2019-01-019-3/+624
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. The U-Boot on WXR-2533DHP employs a complicated dual firmware protection scheme against corruptions of the kernel and rootfs images. See the notes in buffalo.sh for details. specifications: - Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T) - 512 MB of RAM (DDR3) - 256 MB of Flash (NAND) - 4T4R 2.4/5 GHz Wlan (QCA9980) - 5x 10/100/1000 Mbps Ethernet - 10x LEDs, 8x keys (6x buttons, 2x slide-switches) - 2x USB 3.0 Type-A - 12VDC/4A AC Adapter - UART through-hole on PCB - J3: Vcc, GND, TX, RX from USB port side - 115200n8 Boot instructions for the initramfs image: 1. Prepare the TFTP server with the initramfs image renamed to "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10". 2. Press the "AOSS" button while powering on the WXR-2533DHP. 3. Wait until the "Wireless" LED flashes before releasing the AOSS button. The WXR-2533DHP will grab the image from TFTP server and will boot it. Flashing instructions: To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to let it finish the flashing process. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
* base-files: allow non-standard rootfs volume name in UBI in sysupgradeINAGAKI Hiroshi2019-01-011-6/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit allows to use non-standard UBI volume name as the rootfs volume in sysupgrade. ex.: The U-Boot on Buffalo WXR-2533DHP checks existence and checksum of "ubi_rootfs" volume when booting, so this name is required. OpenWrt currently provides several patches: 490-ubi-auto-attach-mtd-device-named-ubi-or-data-on-boot.patch 491-ubi-auto-create-ubiblock-device-for-rootfs.patch 492-try-auto-mounting-ubi0-rootfs-in-init-do_mounts.c.patch to facilitate ubi rootfs automount. However the upstream kernel also supports the means of booting from a fully custom ubi partition name and ubi volume name via bootargs/kernel's cmdline parameters: ubi.mtd=mtd_partition_name ubi.block=rootfs_volume_name root=/dev/ubiblock$X_$Y For more information and examples visit the wiki over at linux-mtd: <http://www.linux-mtd.infradead.org/faq/ubifs.html> <http://www.linux-mtd.infradead.org/doc/ubi.html> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* ipq806x: add ramdisk featureINAGAKI Hiroshi2019-01-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commits adds the "ramdisk" feature to ipq806x target. The main driving force behind this decision is to facilitate the installation of OpenWrt on some locked IPQ806x devices. Examples: - NEC Aterm WG2600HP The U-Boot on WG2600HP is protected with a password which prevents users from gaining access to the u-boot prompt in order to install the images from there. Therefore, on this device, installing OpenWrt by the user involves changing the bootcmd as follows so that WG2600HP downloads and executes initramfs image from TFTP server. ex.: bootcmd="ping ${serverip} && tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" - Buffalo WXR-2533DHP The U-Boot on WXR-2533DHP has built-in firmware recovery mode. It's activated by holding the "AOSS" button during boot. This will trigger the device to download the firmware from an TFTP server and booting from it. By using this, the user can the install OpenWrt firmware without having access to the UART console. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* kernel: Add missing symbols to 4.19Christian Lamparter2019-01-011-0/+1
| | | | | | Tested with apm82181 and ipq40xx minimal image versions. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* busybox: update to 1.30.0Hannu Nyman2019-01-017-18/+65
| | | | | | | | | | | | | | | | | | Update busybox to 1.30.0. Refresh patches. Leave new features disabled by default. Config refreshed via: cd package/utils/busybox/config/ ../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-1.30.0 make package/busybox/compile cd package/utils/busybox ./convert_defaults.pl < ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-1.30.0/.config > Config-defaults.in Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: fix case statement in 01_ledsPaul Wassi2019-01-011-0/+1
| | | | | | Fix a missing 'end-of-case' recently introduced in 01_leds Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: rework elecom-header recipeMathias Kresin2018-12-311-26/+22
| | | | | | | | Replace the code with a more readable version. Rename the recipe to reflect the real usecase. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix spaces vs. tabsPaul Wassi2018-12-312-4/+4
| | | | | | Fix spaces vs. tabs issues in ath79 and ramips. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: tweak the position of factory partition for wr818Rosy Song2018-12-311-8/+8
| | | | | | | | The 'factory' partition will move to 0x50000-0x60000 in 2019. As the webserver in bootloader is compatible with different mtdlayout, all the users still can upgrade firmware whatever on ath79 or ar71xx. Signed-off-by: Rosy Song <rosysong@rosinson.com>
* ath79: add support for COMFAST CF-E110NRoger Pueyo Centelles2018-12-313-0/+175
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E110N, an outdoor wireless CPE with two Ethernet ports and a 802.11bgn radio. Specifications: - 650/400/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 26 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new want, so a factory reset will be needed: once the new firmware is flashed, perform the factory reset by pushing the reset button several times during the boot process, while the WAN LED flashes, until it starts flashing quicker. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Notes: The device is advertised, sold and labeled as "CF-E110N", but the bootloader and the stock firmware identify it as "v2". Acknowledgments: Petr Štetiar <ynezz@true.cz> Sebastian Kemper <sebastian_ml@gmx.net> Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [drop unused labels from devicetree source file] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for TP-Link Archer C6 v2Georgi Vlaev2018-12-317-1/+235
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6 v2 (EU) Hardware specification: - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q64CSIG (8MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: There's no UART header on the board Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing According to the GPL source the non-EU variant has different GPIOs assigned to some of the LEDs and buttons. The flash layout might be different as well. The wikidevi entry for Archer A6/C6 assumes they are identical. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
* ath79: add support for EnGenius EWS511APGuan-Hong Lin2018-12-315-0/+166
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EWS511AP is a wireless managed wall AP with PoE support, based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887. Short specification: - 128MB of RAM - 16 MB of SPI FLASH - 2T2R 2.4 GHz (QCA9531), 802.11b/g/n - 1T1R 5 GHz (QCA9887), 802.11ac/n/a - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED - 1x RESET button - built-in watchdog chipset Flash instruction: From EnGenius firmware to OpenWrt firmware: Original firmware is based on QSDK. Use sysupgrade firmware directly in vendor GUI. Reset to factory default is necessary. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the OpenWrt firmware in the root directory on your computer. 2. Power up EWS511AP. Press 4 and then press any key to enter u-boot. 3. Download OpenWrt firmware (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin" 4. Flash the firmware (ath)> erase 0x9f060000 +f50000 (ath)> cp.b $fileaddr 0x9f060000 $filesize 5. Reboot (ath)> reset Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
* ath79: add status LED on GL.iNet AR300MPaul Wassi2018-12-311-1/+8
| | | | | | This adds the triggers for the status LED of this device. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix boardname of GL.iNet GL-AR300MPaul Wassi2018-12-317-10/+12
| | | | | | | | | | This device is called GL-AR300M, therefore rename the board(s) to 'gl-ar300m-nor' and 'gl-ar300m-nand' Signed-off-by: Paul Wassi <p.wassi@gmx.at> [change boardname in uboot envtools as well, don't use wildcards for boardname] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: Add support for TP-Link WR810NPaul Wassi2018-12-315-1/+182
| | | | | | Device specifications given in b23b0fb28b760ce66a8f93d4681c8bd300d75d30 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: Add GL.iNet AR150 LED triggersPaul Wassi2018-12-311-0/+4
| | | | | | | When switching from ar71xx to ath79 the default netdev LED triggers for LAN and WAN got lost. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix boardname of GL.iNet GL-AR150Paul Wassi2018-12-313-4/+4
| | | | | | | This device is called GL-AR150, therefore rename the board to 'gl-ar150' Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for ELECOM WRC-1750GHBK2-I/CINAGAKI Hiroshi2018-12-316-138/+224
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac routers, based on Qualcomm Atheros QCA9563. This commit also includes small fix; use "0x0x03000101" as pll_1000 instead of "0x03000000". Specification: - SoC: Qualcom Atheros QCA9563 - RAM: 128 MB (DDR2) - Flash: 16 MB (SPI-NOR) - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 10/100/1000 Mbps - LED/key: 4x/3x (2x buttons, 1x slide-switch) - UART: through-hole on PCB - Vcc, RX, GND, TX from switch (QCA8337N) side - 115200n8 Flash instruction using factory image: 1. Boot WRC-1750GHBK2-I/C normaly 2. Access to "http://192.168.2.1/" and open firmware upgrade page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: Fix UBNT Unifi AC LEDsPaul Wassi2018-12-311-2/+2
| | | | | | | Both LEDs on these devices are ACTIVE_HIGH, change back to what it is on ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: Fix system LED on TP-Link WR740/741 v4Paul Wassi2018-12-311-1/+1
| | | | | | | The system LED on these devices is ACTIVE_LOW, change back to what it is on ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for TP-Link TL-WR841N/ND v8Antonio Silverio2018-12-314-0/+175
| | | | | | | | | | | | | | | | | | | CPU: Atheros AR9341 535MHz RAM: 32MB FLASH: 4MiB PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan WiFi: Atheros AR9341 2x2:2 bgn LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill BTN: WPS, WiFi, Reset Installation: Upload the factory image via the vendor-GUI. Signed-off-by: Antonio Silverio <menion@gmail.com> [resolve merge conflicts, squash commits, fix commit title, remove default default off led properties, mark sysupgrade image compatible with the ar71xx version of the board, drop blank lines from dts] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: use caldata patching for Archer C58/C59David Bauer2018-12-312-4/+1
| | | | | | | | | | | With this commit the TP-Link Archer C58 and Archer C59 use caldata patching in order to set the correct 5GHz MAC-address. Tested on TP-Link Archer C59 v1. For more details see commit 330965b. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for GL.iNet GL-AR750SChristoph Krapp2018-12-314-4/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Right now this patch adds nor image generation only. NAND image generation is not supportet at the moment. Furtheremore support for the MicroSD port is not implemented as of now. Specification: - SOC: QCA9563 (775MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x switch button, 1x reset button - LED: 3x LEDS (green) - Another LED can be accessed on GPIO 7 if soldered Flash instruction: - Set static ip to 192.168.1.2 - Unplug the power cord - Hold reset button - Plug power back in - Right led will flash 5 times - Release reset button - Browse to 192.168.1.1 - Choose sysupgrade image in NOR-flash section - Press "update nor firmware" - After successful transfer unplug network cable before device restarts Signed-off-by: Christoph Krapp <achterin@googlemail.com> [resolve merge conflicts, rename buttons, use switch input type for mode switch] Signed-off-by: Mathias Kresin <dev@kresin.me>
* iwinfo: fix PKG_MIRROR_HASHMathias Kresin2018-12-301-1/+1
| | | | | | The PKG_MIRROR_HASH was for some reason wrong. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix OCEDO Koala ethernet configurationDavid Bauer2018-12-301-11/+1
| | | | | | | | | The OCEDO Koala has incorrect PLL settings which result in ~3% packet loss on ethernet connections. Also omit the gmac-configuration as it's incorrect too. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for D-Link DIR-859 A1Weijie Gao2018-12-307-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-859 A1: SoC: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9880 USB is supported on the PCB but not connected. Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Weijie Gao <hackpascal@gmail.com> [squash commits, use common seama recipes, sync factory image recipe with ramips version] Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: move seama commands to image-commands.mkMathias Kresin2018-12-303-23/+12
| | | | | | Move it to image-commands.mk to get rid of duplicate recipes. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-06 08:09:21 +0000