aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* map: fix psidlen becoming negative (FS#1430)Hans Dedecker2018-03-292-11/+17
| | | | | | | | | Fix psidlen becomes negative in case embedded address bit lenght is smaller than IPv4 suffix length. While at it improve parameter checking making the code more logical and easier to read. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* bcm53xx: switch to kernel 4.14Rafał Miłecki2018-03-291-1/+1
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: update kernel 4.14 configRafał Miłecki2018-03-291-7/+34
| | | | | | | | | | | There are few symbol changes but only 3 symbols were possible to set: THERMAL_EMERGENCY_POWEROFF_DELAY_MS CLK_BCM_SR PHY_NS2_USB_DRD Both new drivers don't seem to apply to Northstar so they are disabled. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: fix earlycon regression in kernel 4.14Rafał Miłecki2018-03-291-0/+33
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* Revert "ppp: make ppp-multilink provide ppp"Felix Fietkau2018-03-291-10/+9
| | | | | | | | | | opkg currently has some issues with Provides and this change makes the image builder fail because of that. Revert the change for now until opkg is fixed This reverts commit 092d75aa3e86db8331fffdbd0a99987df9dc438b. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix ar934x usb controller resource conflictFelix Fietkau2018-03-281-1/+1
| | | | | | Use the right size for the EHCI block Signed-off-by: Felix Fietkau <nbd@nbd.name>
* procd: update to the latest versionYousong Zhou2018-03-281-4/+4
| | | | | | | | | | | | Changes since last version dfb68f8 service: initialize supplementary group ids 3db4e6d service: add func for string config change check c3faabe procd: get rid of putenv usage. The supplementary group id change fixes FS#988 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* hostapd: update to git snapshot of 2018-03-26Daniel Golle2018-03-2735-1530/+153
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following patches were merged upstream: 000-hostapd-Avoid-key-reinstallation-in-FT-handshake.patch replaced by commit 0e3bd7ac6 001-Prevent-reinstallation-of-an-already-in-use-group-ke.patch replaced by commit cb5132bb3 002-Extend-protection-of-GTK-IGTK-reinstallation-of-WNM-.patch replaced by commit 87e2db16b 003-Prevent-installation-of-an-all-zero-TK.patch replaced by commit 53bb18cc8 004-Fix-PTK-rekeying-to-generate-a-new-ANonce.patch replaced by commit 0adc9b28b 005-TDLS-Reject-TPK-TK-reconfiguration.patch replaced by commit ff89af96e 006-WNM-Ignore-WNM-Sleep-Mode-Response-without-pending-r.patch replaced by commit adae51f8b 007-FT-Do-not-allow-multiple-Reassociation-Response-fram.patch replaced by commit 2a9c5217b 008-WPA-Extra-defense-against-PTK-reinstalls-in-4-way-ha.patch replaced by commit a00e946c1 009-Clear-PMK-length-and-check-for-this-when-deriving-PT.patch replaced by commit b488a1294 010-Optional-AP-side-workaround-for-key-reinstallation-a.patch replaced by commit 6f234c1e2 011-Additional-consistentcy-checks-for-PTK-component-len.patch replaced by commit a6ea66530 012-Clear-BSSID-information-in-supplicant-state-machine-.patch replaced by commit c0fe5f125 013-WNM-Ignore-WNM-Sleep-Mode-Request-in-wnm_sleep_mode-.patch replaced by commit 114f2830d Some patches had to be modified to work with changed upstream source: 380-disable_ctrl_iface_mib.patch (adding more ifdef'ery) plus some minor knits needed for other patches to apply which are not worth being explicitely listed here. For SAE key management in mesh mode, use the newly introduce sae_password parameter instead of the psk parameter to also support SAE keys which would fail the checks applied on the psk field (ie. length and such). This fixes compatibility issues for users migrating from authsae. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uci: update to latest git HEADHans Dedecker2018-03-271-3/+3
| | | | | | | | 5d2bf09 uci: fix a potential use-after-free in uci_set() 3b3d63e list: only record ordering deltas if element position changed 4c4d343 cmake: Fix cli shared linking against ubox Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* netifd: update to the latest version (fixes FS#1452)Felix Fietkau2018-03-271-4/+4
| | | | | | 9c8d781 netifd: return the interface for locally addressable host dependencies Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: include kmod-ipt-offload in default imagesFelix Fietkau2018-03-271-1/+1
| | | | | | | | | Netfilter flow offload has now started to become useful and suitable for a wider testing audience. Configuring it via UCI is also integrated in firewall3 by adding 'option flow_offloading 1' to the 'defaults' section in /etc/config/firewall Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add kmod-sound-ens1371Felix Fietkau2018-03-251-0/+16
| | | | | | This audio chip is provided as a virtual audio device by VMware Signed-off-by: Felix Fietkau <nbd@nbd.name>
* dnsmasq: improve init script portability (FS#1446)Hans Dedecker2018-03-242-2/+2
| | | | | | | | | | | | | Improve portability of init script by declaring resolvfile as local in dnsmasq_stop function. Fixes resolvfile being set for older busybox versions in dnsmasq_start in a multi dnsmasq instance config when doing restart; this happens when the last instance has a resolvfile configured while the first instance being started has noresolv set to 1. Base on a patch by "Phil" Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* sunxi: add build for sopineFan Fan2018-03-232-0/+20
| | | | | | This will generate image for Pine64 Sopine board. Signed-off-by: Fan Fan <fkpwolf@gmail.com>
* ethtool: Update to 4.15.Rosen Penev2018-03-231-2/+2
| | | | | | Contains kernel 4.14 updates. Compile tested on mvebu. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* Kernel: bump 4.14 to 4.14.29Stijn Segers2018-03-2320-82/+82
| | | | | | | | | | | | Right patch version this time, sorry! * Patch 180-usb-xhci-add-support-for-performing-fake-doorbell.patch had to be adjusted slightly because of upstream adapted code. * Refreshed patches. Compile-tested: ramips/mt7621, x86/64 Run-tested: ramips/mt7621, x86/64 Signed-off-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Rosen Penev <rosenp@gmail.com>
* iproute2: cake: support new overhead reporting & stats structuresKevin Darbyshire-Bryant2018-03-231-266/+969
| | | | | | | | | | | | | | | | | | | | | | Cake in kernel space now splits stats structure handling across netlink messages to reduce stack usage issue flagged by upstream kernel checks. Update user space (tc) qdisc handling to understand this new regime. Cake also reports packet overheads & compensation in a different way so add display code for this. e.g. 'tc -s qdisc show dev eth0' reports this extra detail: min/max transport layer size: 28 / 1500 min/max overhead-adjusted size: 65 / 1550 average transport hdr offset: 14 Cake also supports output in JSON format. Patch is bulkier than before because a (slightly out of date - see above stats) man page is included for reference. Better than nothing! Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kmod-sched-cake: split stats structures, add overhead statsKevin Darbyshire-Bryant2018-03-231-3/+3
| | | | | | | | | | | | | | Relevant changes: 0afc1be Fixes for kernel 4.16 d2d6780 Reinitialise overhead compensation stats when reconfiguring. a3bab9d Export overhead compensation stats to userspace. 9cd2fa8 Split tin stats to its own structure to decrease size of tc_cake_xstats 71c7b44 Gather more statistics about packet length transformations. 0517357 Rework overhead compensation to use dynamic transport header offset instead of (inaccurate) static one. c1a0c8e Refactor length handling code to better centralise overhead calculations Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath10k-ct: fix module dependsHauke Mehrtens2018-03-231-5/+5
| | | | | | | | | | | | PKG_EXTMOD_SUBDIRS should be set to the sub directory where the kernel module gets build in, for the ath10k-ct driver this changed in commit 3888e77c1c68 from ath10k to ath10k-4.13. Without this fix the depends line of the ath10*.ko modules is empty and the kernel module load system will not automatically load the depended modules like mac80211. Fixes: 3888e77c1c68 ("ath10k-ct driver: use dma_alloc_coherent, 4.13 based driver") Fixes: 23a388fe41ec ("ath10k-ct: Force loading mac80211 and ath modules.") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath10k-ct: Add htt-mgt variants of ath10k-ct firmware.Ben Greear2018-03-231-33/+217
| | | | | | | | | | | | | | | | | | The HTT-MGT variants transport management frames over the normal HTT tx path, just like data frames. This saves limitted WMI buffers which can become depleted if lots of management frames become stuck in TX queues due to peer that went away. In addition, at least for the wave-1 firmware, htt-mgt is required in order for 802.11r (fast roaming) authentication to function properly. The htt-mgt firmware requires the use of the ath10k-ct driver. Normal non-htt-mgt ath10k-ct firmware should work with stock drivers. Signed-off-by: Ben Greear <greearb@candelatech.com>
* ath10k-ct: Update wave-1 and wave-2 firmware to latest.Ben Greear2018-03-231-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This updates to latest ath10k-ct firmware. Hopefully we are at the end of the development cycle for this firmware release, so these should be stable. wave-1 changes since last release: Release 20 * Allow flushing peer when deleting. Hopefully this will allow the peer delete command to happen in a reasonable amount of time even if the RF environment is busy (or peer has died). To enable this, set the high flag in the mac-addr second word in the ath10k driver near end of the ath10k_wmi_op_gen_peer_delete method: cmd->peer_macaddr.word1 |= __cpu_to_le32(0x80000000); * Attempt to fix crash seen in resmgr-ocs, appearantly due to list corruption. Use a temporary list instead of trying to rely on for-each-safe. * Add flag to tx-descriptor to allow driver to request no-ack on data frames. This is bit 15 on the flag1 field (previously un-used). * Add option to support specifying the tx-rate-code and retry count on a per-packet basis. Only a single series is supported at this time. Useful mainly for radiotap monitor-tx type testing at this point. * Fix crash on startup when chip is at -40 deg C and calibration fails. Instead of asserting, just keep retrying calibration, which appears to start working after a few minutes (when the chip warms up). * Allow reporting per-chain rssi for management frames. We pack the values into empty space in the mgt-frame wmi header. This will only be enabled if the driver requests it, since otherwise the driver is assumed to not understand the new API. ath10k-ct drivers that support this feature will automatically enable it. * A customer reports a case that appears to be the hardware not properly detecting end of AMPDU, so frames were being mis-delivered to the wrong peer. Attempt to work around this, and in doing so, clean up a bunch of void* abuse in the block-ack reordering code (could not ever confirm there was a problem in this area). * Re-work the rx-mem logic to be less complicated and to use less memory. * Attempt to fix crash that appearanty happens because the driver can sometimes delete a vdev in 'up' state. * Attempt to fix hung scan state machine issues. * Fix crash in tx path due to un-initialized memory. wave-2 changes since last release: Release 10 * Fix an assert related to tx scheduling. This hopefully fixes what appears to be a regression that I added some time back. * Enable CSI reporting for 9984, and maybe 9888/9886. Only in non-trimmed builds. * Other stability improvements, including regression fixes from some tricky bugs introduced in earlier releases. * Allow compiling for IPQ4019 chipset. * Firmware will now send txbf frames to the host (driver) if the TXBF (0xF00000001) set-special feature is enabled, or when the radio is in monitor mode. But, if the frame is consumed by the txbf_cv logic, then the pkt cannot be delivered to the host in this manner. Instead, a WMI event will be sent and host can find the txbf_cv data in shared memory. See ath10k_wmi_event_txbf_cv_mesg() in ath10k-ct driver. * Support rx-all-mgt option. When enabled, the firmware will deliver all management frames that it can to the host. No RX filters are changed when this option is enabled. * Fix at least some problems with sending tx-beamforming frames to SU-MIMO peers. Looks like this was a regression in my code. * Fix a crash in rate-ctrl due to nss mismatch. This was something I introduced while trying to fix other bugs in rate-ctrl some time back. * Attempt to fix a sw-peer-key object leak in IBSS mode. The peer key code is very complex, and shares some pointers as union members. I think I fixed at least some of the issues, but would not be surprised if more exist. * Improve ath10k user guide to document CT firmware features: https://www.candelatech.com/ath10k-ug.php * Add ct-special option to configure the txbf sounding time. See ath10k-ug.php * Fix and allow the driver to tell the firmware to send sounding frames. See ath10k-ug.php In further testing, this seems to fail much of the time, and I am not sure why. Disabling this in diet (trimmed) builds. * Fix crashes related to deleting peers while they are in power-save mode. Reported by LEDE user on r7800 with 9984 NIC. * Make rate-ctrl txbf probe work better. If enabled, the rate-ctrl logic will periodically send out probes at an NSS that can to txbf. Previously, txbf probes would not reliably happen if both AP and peer had the same nss (ie, 2x2 talking to 2x2). To enable this feature, you need to enable the fwtest-cmdid number 20. * Report rx-timeout error counters. These were previously un-reported, though the field existed in the wmi struct already. * txbf: Ignore frames not destined for us. If NIC is in promisc mode, it could acquire and process NDPA frames that were not destined for it. Check the dest-MAC and ignore frames not for us (pass them up the stack for monitor mode instead of save them in the peer's rate-ctrl logic.) * Port ping-pong crash handling and othe related features to IPQ4019 target. It should now act similar to 9984 in this regard. * Fix a few asserts related to txbf and tx-seq logic. * Add custom-stats support, for rx-reorder-stats. Similar to what I did for wave-1. * Disable AMSDU for IBSS. This now matches what I did for peregrine. It seems to work better this way, though I did not debug it in detail. * Enable the set-special command to re-enable AMSDU for IBSS if user wants to experiment. * Fix bug where dbglog did not disable IRQs, so if you made dbglog messages from the IRQ handler, it could cause corruption that could crash the firmware and/or corrupt the log message buffers. * Don't assert if there are no buffer descriptors for RX of non-data frame. * Retry any stuck block-ack sessions every 20 seconds instead of just disabling BA for ever when we get too many failures. * Fix SGI flag when reporting tx-rate info. The flag moved since wave-1 days, and I did not notice that when I ported my changes forward to wave-2. * Allow disabling special CCA handling for IBSS txqs. Earlier testing indicated this might improve throughput in some testing on 9984 chips in IBSS mode, but subsequent testing looks about the same without it. Since I do not really understand what this setting exists for, leave it at upstream defaults. A new set-special API command (0x12) can be used to enable this hack for testing. Setting 0x1 bit disables special CCA handling for non-beacon IBSS txqs, setting 0x2 bit disables it for beacon queues as well. * Add MCAST-BCAST feature flag. This tells driver we do not need a monitor interface to do MESH. * When calculating the rx-address filter (affects ACK & BLOCK-ACK, among other things), to not add in monitor interfaces if other interfaces are up. There is no need for a monitor device to ACK frames. Signed-off-by: Ben Greear <greearb@candelatech.com>
* ath10k-ct: Update driver to latest.Ben Greear2018-03-231-3/+3
| | | | | | | | Among other things, this will check for an htt-mgt variant of ath10k-ct firmware before loading 'normal' firmware, and it disables verbose printing of firmware DBGLOG messages by default. Signed-off-by: Ben Greear <greearb@candelatech.com>
* ath10k-ct: Update DEPENDS and PROVIDESBen Greear2018-03-232-0/+9
| | | | | | | | | | Update DEPENDS and PROVIDES so that ath10k-ct firmware and drivers can be used to replace stock firmware and drivers. The -htt firmware variant, which requires ath10k-ct driver now selects ath10k-ct driver when the firmware is selected. Signed-off-by: Ben Greear <greearb@candelatech.com>
* libubox: update to the latest versionFelix Fietkau2018-03-231-3/+3
| | | | | | | 3aad294 libubox: Plug a small memory leak. eebe3fc utils: use constant byte-order conversion Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: remove dead (and potentially crashy) code in mt7621 gsw initFelix Fietkau2018-03-231-11/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: rename ethernet priv->device field to dev to match upstreamFelix Fietkau2018-03-237-26/+26
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: netfilter: fix dst entries in flowtable offloadFelix Fietkau2018-03-232-11/+111
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix crash in flow offload when removing net devicesFelix Fietkau2018-03-231-3/+5
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: flow-offload: only offload connections that have been fully establishedFelix Fietkau2018-03-231-1/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: intel-xway: add vr9 v1.1 phy supportMathias Kresin2018-03-234-0/+264
| | | | | | | | | | | | During upstreaming the intel phy driver, support for the vr9 v1.1 embedded phys got lost. Backport the upstream send patch adding support for the vr9 v1.1 embbeded phys to the driver. Signed-off-by: Mathias Kresin <dev@kresin.me> cosmetic fixes Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix switch and MAC address for WHR-G300NINAGAKI Hiroshi2018-03-232-1/+7
| | | | | | | | | | | | WHR-G300N has 5 ethernet ports (lan: 4, wan: 1), but there was no correct configuration in 02_network script and 6 ports was configured on the switch. Also, since the MAC address was not acquired from factory partition, incorrect values was set to LAN and WAN interfaces. This commit fixes these issues. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq40xx: Add reserved memory for WPJ428Sven Eckelmann2018-03-231-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The APPSBL and anything after that it not allowed to touch some of the memory regions which are used by other components. Still trying to write to the memory can lead to sudden device restarts (IPQ40xx) # mw 87e80000 0 data abort pc : [<873149f8>] lr : [<87308578>] sp : 86edfc28 ip : 86ef4412 fp : 00000000 r10: 00000000 r9 : 00000000 r8 : 86edff68 r7 : 00000003 r6 : 8737e624 r5 : 86ef4420 r4 : 8736c154 r3 : 00000000 r2 : 00000010 r1 : 00000000 r0 : 00000000 Flags: nZCv IRQs off FIQs off Mode SVC_32 Resetting CPU ... The device manufacturer only provided a very rough list of regions: * rsvd1: 0x87000000 0x500000 * wifi_dump: 0x87500000 0x600000 * rsvd2: 0x87b00000 0x500000 A more detailed list for devices using the AP.DK reference design memory maps was provided by Roman Yeryomin <roman@advem.lv> in commit 56f2df879fd ("ipq806x: ipq4019: add ap-dk01.1-c1 board support"): * apps_bl: 0x87000000 0x400000 * sbl: 0x87400000 0x100000 * cnss_debug: 0x87500000 0x600000 * cpu_context_dump: 0x87b00000 0x080000 * tz_apps: 0x87b80000 0x280000 * smem: 0x87e00000 0x080000 * tz: 0x87e80000 0x180000 The u-boot function ipq_fdt_mem_rsvd_fixup seems to suggest that only the rsvd2 (tz_apps, smem, tz) should be protected. All other regions would have been removed by it when CONFIG_QCA_APPSBL_DLOAD is not enabled. This allows to reduce the 16MB reserved memory region to only 4.5MB. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Use detailed reserved memory for A42Sven Eckelmann2018-03-231-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The APPSBL and anything after that it not allowed to touch some of the memory regions which are used by other components. Still trying to write to the memory can lead to sudden device restarts (IPQ40xx) # mw 87e80000 0 data abort pc : [<873149f8>] lr : [<87308578>] sp : 86edfc28 ip : 86ef4412 fp : 00000000 r10: 00000000 r9 : 00000000 r8 : 86edff68 r7 : 00000003 r6 : 8737e624 r5 : 86ef4420 r4 : 8736c154 r3 : 00000000 r2 : 00000010 r1 : 00000000 r0 : 00000000 Flags: nZCv IRQs off FIQs off Mode SVC_32 Resetting CPU ... The device manufacturer only provided a very rough list of regions: * rsvd1: 0x87000000 0x500000 * wifi_dump: 0x87500000 0x600000 * rsvd2: 0x87b00000 0x500000 A more detailed list for devices using the AP.DK reference design memory maps was provided by Roman Yeryomin <roman@advem.lv> in commit 56f2df879fd ("ipq806x: ipq4019: add ap-dk01.1-c1 board support"): * apps_bl: 0x87000000 0x400000 * sbl: 0x87400000 0x100000 * cnss_debug: 0x87500000 0x600000 * cpu_context_dump: 0x87b00000 0x080000 * tz_apps: 0x87b80000 0x280000 * smem: 0x87e00000 0x080000 * tz: 0x87e80000 0x180000 The u-boot function ipq_fdt_mem_rsvd_fixup seems to suggest that only the rsvd2 (tz_apps, smem, tz) should be protected. All other regions would have been removed by it when CONFIG_QCA_APPSBL_DLOAD is not enabled. This allows to reduce the 16MB reserved memory region to only 4.5MB. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Remove phy reset gpio from Cisco Meraki MR33Sven Eckelmann2018-03-231-1/+0
| | | | | | | | There is currently no code to read the phy reset gpios for the ethernet PHY. It would also have been better to use the more common name "phy-reset-gpios" for this property. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Adjust SoC name of AVM Fritz!Box 4040Sven Eckelmann2018-03-233-2/+2
| | | | | | | The AVM Fritz!Box 4040 uses an IPQ4018 as SoC and not an IPQ4019. The DTS must be adjusted to reflect this. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Use constant to set gpio active low/highSven Eckelmann2018-03-237-8/+9
| | | | | | | | | The GPIO configuration in the DTS have as third parameter the active low/high configuration. This parameter is not easy to parse by humans when it is only set to 0/1. It is better to use the predefined constants GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Fix DTS status parameter valuesSven Eckelmann2018-03-234-47/+47
| | | | | | | | The "Devicetree Specification, Release v0.2 - 2.3.4 status" [1] only allows the "okay" value for an operational device. The "ok" value will be accepted by the kernel but should be avoided. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Provide prefered DTS config name for A42Sven Eckelmann2018-03-231-0/+1
| | | | | | | | The OpenMesh A42 will use the default config entry in the FIT when no other on is found but prefers the config@om.a42. This only becomes relevant when a Multi-FIT image is prepared for this device. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Remove SUPPORTED_DEVICES for A42Sven Eckelmann2018-03-231-1/+0
| | | | | | | The SUPPORTED_DEVICES will be defined automatically via Device/Default in ipq40xx. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* kernel: fix offloading connections with SNAT + DNATFelix Fietkau2018-03-231-0/+23
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix flow offload UDP handling issueFelix Fietkau2018-03-231-0/+48
| | | | | | Only run the TCP state check for TCP connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* busybox: drop providing virtual package ipHans Dedecker2018-03-221-1/+0
| | | | | | | | | | | | | | Drop providing the virtual package ip by busybox which was added in commit 1cec4d4ef0. Letting busybox provide the virtual package ip is not optimal for the following reasons : - Applications depending on ip expect either the ip-full or ip-tiny package to be enabled. - Busybox ip applet cannot be added or removed at runtime Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* firewall: update to latest git HEADHans Dedecker2018-03-221-3/+3
| | | | | | | | | 5cdf15e helpers.conf: add CT rtsp helper d5923f1 Reword rule comments c1a295a defaults: add support for xt_FLOWOFFLOAD rule 41c2ab5 ipsets: add support for specifying entries Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath10k-firmware: Support CT IPQ4019 firmware.Ben Greear2018-03-221-3/+71
| | | | | | | Initial beta release of the CT IPQ4019 firmware. Features are similar to the CT 9984 firmware Signed-off-by: Ben Greear <greearb@candelatech.com>
* ath10k-ct: Force loading mac80211 and ath modules.Ben Greear2018-03-221-1/+1
| | | | | | | They are not automatically loaded on IPQ4019 (at least) machines for some reason. Signed-off-by: Ben Greear <greearb@candelatech.com>
* ath10k-ct: update to latest version, enable AHB.Ben Greear2018-03-222-42/+8
| | | | | | | | | | | | | | | | The driver updates include: ath10k driver backport to fix WPA 'pn' related security bugs (4.13 based driver only currently), a fix for off-channel TX for CT wave-1 firmware, a likely fix for napi related crashes, and a backport of the firmware fetch patch. AHB is needed for the IPQ4019 platform radios. Signed-off-by: Ben Greear <greearb@candelatech.com> [use common subject format] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* intel-microcode: update to 20180312Zoltan HERPAI2018-03-211-3/+3
| | | | | | | | | | | | | | | | - Update microcode for 24 CPU types - Implements IBRS/IBPB/STIPB support, Spectre-v2 mitigation for: Sandybridge, Ivy Bridge, Haswell, Broadwell, Skylake, Kaby Lake, Coffee Lake - Missing production updates: - Broadwell-E/EX Xeons (sig 0x406f1) - Anniedale/Morefield, Apollo Lake, Avoton, Cherry Trail, Braswell, Gemini Lake, Denverton - New Microcodes: - sig 0x00050653, pf_mask 0x97, 2018-01-29, rev 0x1000140 - sig 0x00050665, pf_mask 0x10, 2018-01-22, rev 0xe000009 Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-sunxi: refresh patchesZoltan HERPAI2018-03-217-12/+12
| | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-sunxi: fix build by adding comparabilities for old dtcHauke Mehrtens2018-03-211-0/+52
| | | | | | | | | We use the dtc from the kernel and that does not have all the options which u-boot would like to use now. make these parameters optional. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> [wigyori@uid0.hu: renamed to 221-compatible-old-dtc.patch from 220-] Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-sunxi: bump again to 2017.11Zoltan HERPAI2018-03-2111-392/+36
| | | | | | | | | | | | | | | Runtime-tested on: - Pine64 (A64) - Orange Pi 2 (H3) - Bananapro (A20) - Olimex A20-Micro (A20) - Pcduino v3 (A20) - Pcduino v2 (A10) Compile-tested on: - all A8/A7/A53 boards Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-30 16:52:17 +0000