aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* ath79: support for TP-Link EAP225 v4Sven Hauer2022-06-283-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This model is almost identical to the EAP225 v3. Major difference is the RTL8211FS PHY Chipset. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO * Ethernet (RTL8211FS): 1× 1GbE, 802.3at PoE Flashing instructions: * ssh into target device and run `cliclientd stopcs` * Upgrade with factory image via web interface Debricking: * Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R225 (TXD) and R237 (RXD). Do NOT bridge R230. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. Signed-off-by: Sven Hauer <sven.hauer+github@uniku.de>
* hostapd: introduce min_tx_power optionStijn Tintel2022-06-281-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduce a new option min_tx_power to configure the minimum permitted max TX power (in dBm) for ACS and DFS channel selection. Imagine the following regulatory rules: * 5180 MHz [36] (21.0 dBm) * 5200 MHz [40] (21.0 dBm) * 5220 MHz [44] (21.0 dBm) * 5240 MHz [48] (21.0 dBm) * 5260 MHz [52] (20.0 dBm) (radar detection) * 5280 MHz [56] (20.0 dBm) (radar detection) * 5300 MHz [60] (20.0 dBm) (radar detection) * 5320 MHz [64] (20.0 dBm) (radar detection) * 5500 MHz [100] (21.0 dBm) (radar detection) * 5520 MHz [104] (21.0 dBm) (radar detection) * 5540 MHz [108] (21.0 dBm) (radar detection) * 5560 MHz [112] (21.0 dBm) (radar detection) * 5580 MHz [116] (21.0 dBm) (radar detection) * 5600 MHz [120] (21.0 dBm) (radar detection) * 5620 MHz [124] (21.0 dBm) (radar detection) * 5640 MHz [128] (21.0 dBm) (radar detection) * 5660 MHz [132] (21.0 dBm) (radar detection) * 5680 MHz [136] (21.0 dBm) (radar detection) * 5700 MHz [140] (21.0 dBm) (radar detection) * 5720 MHz [144] (13.0 dBm) (radar detection) * 5745 MHz [149] (13.0 dBm) * 5765 MHz [153] (13.0 dBm) * 5785 MHz [157] (13.0 dBm) * 5805 MHz [161] (13.0 dBm) * 5825 MHz [165] (13.0 dBm) * 5845 MHz [169] (13.0 dBm) * 5865 MHz [173] (13.0 dBm) When ACS or DFS end up selecting channel 144 or higher, some clients might no longer be able to communicate with the AP due to the TX power being limited to 13 dBm. Setting min_tx_power to 20 will result in hostapd not considering these channels during ACS or after a DFS event. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: David Bauer <mail@david-bauer.net>
* hostapd: introduce background_radar optionStijn Tintel2022-06-281-1/+6
| | | | | | | | | | | | | | Introduce a new option background_radar to toggle hostapd's background radar feature. Enabling this allows DFS CAC to run on dedicated radio RF chains while the radio(s) are otherwise running normal AP activities on other channels. As OpenWrt configures hostapd to use a channel list even when a single channel is configured, using this feature requires a list of channels in /etc/config/wireless. Alternatively, channel can be set to auto. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: David Bauer <mail@david-bauer.net>
* hostapd: support MBO in bss_transition_requestStijn Tintel2022-06-282-3/+61
| | | | | | | Support the use of MBO in the bss_transition_request ubus method. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: David Bauer <mail@david-bauer.net>
* hostapd: introduce mbo optionStijn Tintel2022-06-281-2/+9
| | | | | | | | Introduce a new option mbo to toggle Multi Band Operation aka Agile Multiband for a BSS. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: David Bauer <mail@david-bauer.net>
* hostapd: enable MBO if 802.11ax is enabledStijn Tintel2022-06-281-0/+1
| | | | | | | | Multi Band Operation is required for 802.11ax certification, so let's enable it if 802.11ax support is enabled. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: David Bauer <mail@david-bauer.net>
* hostapd: add config symbol to enable MBOStijn Tintel2022-06-282-0/+15
| | | | | | | | | | Multi Band Operation aka Agile Multiband introduces new Transition and Transition Rejection Reason Codes that should improve client steering. Add a config symbol to enable it, and enable it by default for the full variants. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: David Bauer <mail@david-bauer.net>
* kernel: backport RTL8211F clkout-disable patchSander Vanheule2022-06-271-0/+119
| | | | | | | | | | | | | | In Linux v5.14 an extra feature was introduced for the RTL8211F phy, allowing to disable a clock output from the phy. Part of that patch is to always (soft) reset the phy upon initialisation. This phy reset is required to have a working ethernet on the TP-Link EAP225-Outdoor v3 and EAP225 v4 after a reboot. Otherwise the ethernet port will only function properly on cold boots. Tested-by: Andre Klärner <kandre@ak-online.be> # EAP225-Outdoor v3 Tested-by: Sven Hauer <sven.hauer+github@uniku.de> # EAP225 v4 Signed-off-by: Sander Vanheule <sander@svanheule.net>
* firmware-utils: bump to git HEADSander Vanheule2022-06-271-2/+2
| | | | | | | | | | | | | The support-list partition for the EAP225-V3 board ID became larger than the allocated size, resulting in factory image generation for the EAP225-Outdoor v3 and EAP225 v3 to fail. The make directive Build/tplink-safeloader ignores this failure however, resulting in a seemingly successful build with empty factory images. Included changes: e609c5d75186 tplink-safeloader: drop unqualified EAP225-V3 IDs Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath10k: enable encapsulation offload by defaultTiago Gaspar2022-06-271-1/+2
| | | | | | | | | | | | | | Enable ath10k offload by default. This improves wireless performance without requiring user configuration. This adds ath10k_core to the AUTOLOAD section so that the frame_mode paramter can be added to /etc/modules.d and passed to the driver. The frame_mode 2 enables ethernet mode on the firmware/driver. This parameter is set by passing a different value to the frame_mode value on kmod insmod. Link to the original patchset: https://patchwork.kernel.org/project/linux-wireless/cover/20220516032519.29831-1-ryazanov.s.a@gmail.com/ Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
* lantiq: dts: td-w8980: Remove duplicate PCI propertiesMartin Blumenstingl2022-06-271-3/+1
| | | | | | | | | lantiq,bus-clock, interrupt-map-mask and interrupt-map are already defined with these exact values in vr9.dtsi. Drop them from vr9_tplink_tdw8980.dts to just have one place where these are maintained. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* kernel: bump 5.15 to 5.15.49Rui Salvaterra2022-06-2728-231/+170
| | | | | | | | | Deleted (upstreamed): generic/backport-5.15/702-v5.19-34-net-ethernet-mtk_eth_soc-fix-misuse-of-mem-alloc-int.patch [1] [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.49&id=fcba12a4308143f1f1dcb0face8b3ffb51edcc5c Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.15 to 5.15.48Rui Salvaterra2022-06-271-2/+2
| | | | | | No patches needed rebasing. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.15 to 5.15.47Rui Salvaterra2022-06-2727-120/+95
| | | | | | | | | | | Deleted (upstreamed): generic/backport-5.15/702-v5.19-32-net-ethernet-mtk_eth_soc-out-of-bounds-read-in-mtk_h.patch [01] [01] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.47&id=b24ca1cf846273361d5bd73a35de95a486a54b6d Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> [Removed 702-v5.19-32-net-ethernet-mtk_eth_soc-out-of-bounds-read-in-mtk_h.patch] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.15 to 5.15.46Rui Salvaterra2022-06-2759-624/+94
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Deleted (upstreamed): generic/backport-5.15/400-mtdblock-warn-if-opened-on-NAND.patch [01] generic/backport-5.15/420-v5.19-01-mtd-spinand-gigadevice-fix-Quad-IO-for-GD5F1GQ5UExxG.patch [02] bcm27xx/patches-5.15/950-0029-Revert-mailbox-avoid-timer-start-from-callback.patch [03] bcm27xx/patches-5.15/950-0417-bcm2711_thermal-Don-t-clamp-temperature-at-zero.patch [04] bcm27xx/patches-5.15/950-0740-drm-vc4-hvs-Fix-frame-count-register-readout.patch [05] bcm27xx/patches-5.15/950-0755-drm-vc4-hvs-Reset-muxes-at-probe-time.patch [06] bcm27xx/patches-5.15/950-0759-drm-vc4-txp-Don-t-set-TXP_VSTART_AT_EOF.patch [07] bcm27xx/patches-5.15/950-0760-drm-vc4-txp-Force-alpha-to-be-0xff-if-it-s-disabled.patch [08] bcm53xx/patches-5.15/031-v5.17-0005-ARM-dts-BCM5301X-update-CRU-block-description.patch [09] mediatek/patches-5.15/102-mt7629-enable-arch-timer.patch [10] Manually rebased: bcm27xx/patches-5.15/950-0741-drm-vc4-hvs-Use-pointer-to-HVS-in-HVS_READ-and-HVS_W.patch [01] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=f41c9418c5898c01634675150696da290fb86796 [02] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=d5b66645305c6f3a1b2cf75cee4157b07f293309 [03] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=119f99209d8531359bcb935f252ec435f9d21b13 [04] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=c4e1280abead1552e1764684079a43e222ccd163 [05] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=08465a1889cb48ec64431e9db745b5be15399251 [06] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=0e26a6da02e63b75b629573d13966c36aa6264f0 [07] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=01c9020b2e7c85e394879f34851805179ac3d1d8 [08] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=d47f85cc0171a5d3c5bd8cbb8a98983ca3357cbd [09] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=5151f24ac937ff7eb1f078257c66e3c0f0296010 [10] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=ffea838686b82fbb2801cdfad6ba5309d15c032d Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: 5.15: x86-64: enable CONFIG_SLSRui Salvaterra2022-06-271-0/+1
| | | | | | | | Starting with GCC 12, we have the possibility of mitigating straight-line speculation vulnerabilities in x86-64 targets. Make it so. Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.125John Audia2022-06-273-4/+4
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.124John Audia2022-06-2735-176/+157
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.123John Audia2022-06-271-2/+2
| | | | | | | | | No patches required a rebase, just updated checksum. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.122John Audia2022-06-2723-61/+61
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.121John Audia2022-06-2735-64/+64
| | | | | | | | | | | | Manually rebased: oxnas/patches-5.10/100-oxnas-clk-plla-pllb.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* valgrind: bump to 3.19.0Rui Salvaterra2022-06-274-6/+6
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* opkg: update to 2022-02-24Josef Schlehofer2022-06-271-3/+3
| | | | | | | | | | Changes: 9c44557 opkg_remove: avoid remove pkg repeatly with option --force-removal-of-dependent-packages 2edcfad libopkg: set 'const' attribute for argv This should fix the CI error in the packages repository, which happens with perl. Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* dropbear: cherry-pick upstream commit 544f28a0Konstantin Demin2022-06-271-0/+134
| | | | | | | Resolves #10081 Reported-By: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
* tools/meson: update to 0.61.5Rosen Penev2022-06-271-2/+2
| | | | | | | Mostly backports by a Red Hat employee as 0.62 and newer demands Python 3.7+. Same reason 0.61 is kept here. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* arptables: update to 0.0.5 and cleanupNick Hainke2022-06-271-9/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Update to 0.0.5: efae894 arptables 0.0.5 release 1f3c6bc libarptc: Simplify alloc_handle by using calloc() 4e5e23a Eliminate compiler warning about size passed to strncmp() bf11d72 Add .gitignore 28b22d5 arptables: legacy renaming 988d6a4 arptables: cleanup sysvinit script f4ab8f6 src: Remove support for libc5 047f37b src: Use stdint types 4bb2f83 arptables: Add MARK target dbbe9f7 arptables: Add revision field for arptables userspace 935acea src: fix compilation warning 5700dbf src: cache in tree and use x_tables.h 4b7d6b0 arptables: remove dead dynamic hooks code c299484 arptables: fix potential buffer overflow (author: dcb) 9fcaf70 arptables: add missing long option --set-counters and update documentation 36daba3 arptables: install man pages f79b957 Add man pages for arptables-{save,restore} c492c16 add GPL text 8f58693 fix potential buffer overflows reported by static analysis ee4ec13 make static analysis tool happy (false positive) b064d44 build an libarptc.a archive Cleanup Makefile: - Switch to release versions - Use ftp(http) mirror - Add PKG_LICENSE_FILES Signed-off-by: Nick Hainke <vincent@systemli.org>
* ethtool: update to 5.18Nick Hainke2022-06-271-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | 9eabf30 Release version 5.18. 2b3ddcb ethtool: fec: Change the prompt string to adapt to current situations d660dde pretty: add missing message descriptions for rings aaeb16a pretty: support u8 enumerated types 6b320b8 rings: add support to set/get cqe size 41fddc0 update UAPI header copies 42e6c28 help: fix alignment of rx-buf-len parameter e1d0a19 ethtool.8: Fix typo in man page 37f0586 Release version 5.17. 8c2984c strset: do not put a pointer to a local variable to nlctx 8fd02a2 ioctl: add the memory free operation after send_ioctl call fails b9f25ea ethtool: Add support for OSFP transceiver modules 6e79542 features: add --json support 5ed5ce5 Merge branch 'next' into master b90abbb man: document recently added parameters 51a9312 tunables: add support to get/set tx copybreak buf size a081c2a rings: add support to set/get rx buf len d699bab Merge branch 'master' into next 52db6b9 Merge branch 'review/module-extstate' into next 6407b52 monitor: add option for --show-module/--set-module 1f35786 ethtool: Add transceiver module extended state 2d4c5b7 ethtool: Add ability to control transceiver modules' power mode 005908b Update UAPI header copies Signed-off-by: Nick Hainke <vincent@systemli.org>
* wolfssl: disable AES-NI by default for x86_64Eneas U de Queiroz2022-06-271-1/+6
| | | | | | | | | | | | WolfSSL is crashing with an illegal opcode in some x86_64 CPUs that have AES instructions but lack other extensions that are used by WolfSSL when AES-NI is enabled. Disable the option by default for now until the issue is properly fixed. People can enable them in a custom build if they are sure it will work for them. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* firmware-utils: bump to git HEADSander Vanheule2022-06-261-2/+2
| | | | | | | | | Fixes the safeloader model identifiers for EAP225-Outdoor v1/v3 devices. 1e3d47292b2e tplink-safeloader: fix EAP225-Outdoor model IDs 9563fe8e78cb tplink-safeloader: add regionless EAP225-V3 IDs Signed-off-by: Sander Vanheule <sander@svanheule.net>
* mac80211: increase airtime scheduler quantumFelix Fietkau2022-06-261-0/+53
| | | | | | improves performance by requiring fewer iterations over tx queues Signed-off-by: Felix Fietkau <nbd@nbd.name>
* realtek: cleanup LAG loggingMarkus Stockhausen2022-06-261-12/+14
| | | | | | | | Setting up DSA bond silently fails if mode is not 802.3ad. Add log message to fix it. As we are already here harmonize all logging messages in the add/delete functions. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
* mac80211: add airtime fairness improvementsFelix Fietkau2022-06-259-6/+1698
| | | | | | | | This reverts the airtime scheduler back from the virtual-time based scheduler to the deficit round robin scheduler implementation. This reduces burstiness and improves fairness by improving interaction with AQL. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* realtek: EnGenius EWS2910P: add support for SFP portsAlexandru Gagniuc2022-06-251-0/+49
| | | | | | | | | | | | | | | | | | | | | | The SFP cages 9F and 10F share the same SCL line. Currently, there isn't a good way to model this. Thus, only one SFP port can be fully supported. Cage 10F is fully supported with an I2C bus and sfp handle. Linux automatically handles enabling or disabling the TX laser. Cage 9F is only parially supported, without the sfp handle. The SDA line is hogged as an input, so that it remains high. SCL transitions sould not affect modules connected to this cage. The default value of the tx-disable line is high (active). It is exported as a gpio, but the laser is off by default. To enable the laser: echo 0 > /sys/class/gpio/sff-p9-tx-disable/value Thus, both modules can be used for networking, but only 10F will be able to detect and identify a plugged in SFP module. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
* realtek: add support for EnGenius EWS2910PAlexandru Gagniuc2022-06-252-0/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the Engenius EWS2910P PoE switch. This is an RTL8380 based switch with two SFP slots, and PoE 802.3af one every RJ-45 port. The specs say 802.3af, but the vendor firmware configures the PSE for a budget of 31W, indicating 802.3at support. Specifications: --------------- * SoC: Realtek RTL8380M * Flash: 32 MiB SPI flash Macronix MX25L25635E * RAM: 256 MiB (As reported by bootloader) * Ethernet: 16x 10/100/1000 Mbps with PoE 2x SFP slots * Buttons: 1 "Reset" button on front panel 1 "LED mode: button on front panel 1 "On/Off" Toggle switch on the back * Power: 48V-54V DC barrel jack * UART: 1 serial header (JP1) with populated 2.54mm pitch header Labeled GRTV for ground, rx, tx, and 3.3V respectively * PoE: 1 STM ST32F100 microcontroller 2 BCM59111 PSE chips Works: ------ - (8) RJ-45 ethernet ports - Switch functions - LEDs and buttons Not yet enabled: ---------------- - SFP ports (will be enabled in a subsequent change) - Power-over-Ethernet (requires realtek-poe package) Install via web interface: ------------------------- The factory firmware will accept and flash the initramfs image. It is recommended to flash to "Partition 0". Flashing to "Partition 1" is not supported at this point. The factory web GUI will show the following warning: " Warning: The firmware version is v0.00.00-c0.0.00 The firmware image you are uploading is older than the current firmware of the switch. The device will reset back to default settings. Are you sure you want to proceed?" This is expected when flashing OpenWrt. After the initramfs image boots, flash the -sysupgrade using either the commandline or LuCI. Install via serial console/tftp: -------------------------------- The u-boot firmware will not stop the boot, regardless of which key is pressed. To access the u-boot console, ground out the CLK (pin 16) of the ROM (U22) when u-boot is reading the linux image. If timed correctly, the image CRC will fail, and u-boot will drop to a shell: > rtk network on > setenv ipaddr <address of tftp server> > tftp $(freemem) <name-of-initramfs-image.bin> > bootm Then flash the -sysupgrade using either the commandline or luci. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> [gpio-led node names, OpenWrt and LuCI capitalization in commit message] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ramips: add support for Asus RT-N12+ B1 and RT-N300 B1Semih Baskan2022-06-251-0/+6
| | | | | | | | | | | | | | Asus RT-N12+ B1 and Asus RT-N300 B1 are the same device with a different name. The OEM firmwares have the same MD5 with Asus RT-N11P B1. Same instructions for Asus RT-N11P B1 see: commit c3dc52e39ac8 ("ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1") Signed-off-by: Semih Baskan <strstgs@gmail.com> (Added id from the PR review to commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for ASUS RT-AX53UChuncheng Chen2022-06-253-0/+182
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX53U - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 3 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - Ports: USB 3.0 - LEDs: 1x POWER (blue, configurable) 3x LAN (blue, configurable) 1x WAN (blue, configurable) 1x USB (blue, not configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com> (replaced led label, added key-* prefix to buttons, added note about BBT) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kexec-tools: add kdump scripts utilChen Minqiang2022-06-251-0/+34
| | | | | | This add back kdump scripts to save crashlog or vmcore to disk Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* apm821xx: WNDAP660: fix ethernet port orderingChristian Lamparter2022-06-254-13/+13
| | | | | | | | | | | | | | | | | | Tim Small reported: | Viewing the 'Network' -> 'Switch' config page in LuCI: | | The LuCI LAN 1 port corresponds to the port physically | labelled 2 at the rear of the device. | [...] | | When a patch cord is attached to the port labelled 1 [...], | the LED labelled 2 illuminates. [...] => Ports, LuCI and LEDs are reversed/don't match. Reported-by: Tim Small Fixes: #10111 Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: fix damaged config 5.10 refreshChristian Lamparter2022-06-243-5/+3
| | | | | | | | | | | | Restore CONFIG_I8K + CONFIG_INTEL_INT0002_VGPIO that got removed when I refreshed the config. Each x86 target gets its own CONFIG_CRYPTO_BLAKE2S + LIB settings as only the x86_64 can use the accelerated x86 version. Also remove two extra spaces that sneaked into geode's config. Fixes: 539e60539a2f ("generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* octeon: add support for Ubiquiti UniFi Security GatewayClemens Hopfer2022-06-248-6/+211
| | | | | | | | | | | | | | | | | | | Ubiquiti UniFi Security Gateway (USG) is largely identical to the EdgeRouter Lite (ERLite-3) apart from a different board ID and two dome leds. Device data (from WikiDev): CPU: Cavium Octeon Plus CN5020 @500MHz 2-cores Ethernet: 3x Atheros AR8035-A GbE PHY's Flash: On-board 4MB Flash Storage: Internal 3.8GB USB Flash (Kingston ID) drive w/ 1.5GB free for use occupies single internal USB port. Serial: 1x RJ45 port on front panel. 115200, 8N1 Buttons: 1x Reset Flash instructions are identical to EdgeRouter Lite. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
* mt76: update to the latest versionFelix Fietkau2022-06-241-3/+3
| | | | | | | | | | | | | | | 1696f9eb8b40 mt76: mt7915: do not copy ieee80211_ops pointer in mt7915_mmio_probe a4db5869d660 mt76: mt7915: update mpdu density in 6g capability 500c18014d95 mt76: mt7915: add sta_rec with EXTRA_INFO_NEW for the first time only 3ef66fc7c714 mt76: do not check the ccmp pn for ONLY_MONITOR frame dd682eead016 mt76: mt7915: update the maximum size of beacon offload 4fb991f2c997 mt76: mt7615: add sta_rec with EXTRA_INFO_NEW for the first time only ba39ed3b44f1 mt76: mt76x02: improve reliability of the beacon hang check fd8211cf7c59 mt76: mt7921: sync with updated patch f2edd340ddb4 mt76: allow receiving frames with invalid CCMP PN via monitor interfaces b6e865e2cc70 mt76: mt7615: fix throughput regression on DFS channels Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: fix rootfs padding for D-Link DAP-2xxxSebastian Schaper2022-06-241-1/+2
| | | | | | | | | | | It was observed that `rootfs_data` was sometimes not correctly erased after performing sysupgrade, resulting in previous settings to prevail. Add call to `wrgg-pad-rootfs` in sysupgrade image recipe to ensure any previous jffs2 will be wiped, consistent with DAP-2610 from the ipq40xx target, which introduced the double-flashing procedure for these devices. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* mac80211: brcmfmac: allow setting MAC from NVMEM cellsTomasz Maciej Nowak2022-06-243-4/+107
| | | | | | | | | The MAC can be stored in OTP memory or in flash memory, currently the driver could read it only from OTP. Backport the patch allowing setting the MAC address from flash. Some modules have the OTP programmed but the ODM/OEM decided to overwrite it with value stored in flash. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]Tomasz Maciej Nowak2022-06-2489-2/+175
| | | | | | | | | | | | This is now built-in, enable so it won't propagate on target configs. Link: https://lkml.org/lkml/2022/1/3/168 Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44") Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (Link to Kernel's commit taht made it built-in, CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: clean-up after kernel 5.4 removalTomasz Maciej Nowak2022-06-248-30/+19
| | | | | | | These narrowments are no longer useful, since there's no lower version than 5.10 supported in tree. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* nftables: update to 1.0.4Nick Hainke2022-06-241-2/+2
| | | | | | | | | | | | Needs libnftnl 1.2.2. 3eb0da9f build: Bump version to 1.0.4 a964d1b5 tests: shell: remove leftover modules on cleanup 818f7dde evaluate: reset ctx->set after set interval evaluation 3835de19 tests: shell: sets_with_ifnames release netns on exit 59bd944f optimize: segfault when releasing unsupported statement Signed-off-by: Nick Hainke <vincent@systemli.org>
* libnftnl: update to 1.2.2Nick Hainke2022-06-241-2/+2
| | | | | | | | build: libnftnl 1.2.2 release accee9a set_elem: missing export symbol e2514c0 exthdr: tcp option reset support Signed-off-by: Nick Hainke <vincent@systemli.org>
* nftables: clean up MakefileNick Hainke2022-06-241-3/+4
| | | | | | Add PKG_LICENSE_FILES. Use SPDX. Signed-off-by: Nick Hainke <vincent@systemli.org>
* nftables: update to 1.0.3Nick Hainke2022-06-242-32/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove backport: - 001-examples-compile-with-make-check.patch 87fdf683 build: Bump version to 1.0.3 c4ec825b nft: simplify chain lookup in do_list_chain 4f6724f1 intervals: fix compilation --with-mini-gmp 4c20fe95 json: update json output ordering to place rules after chains 57741350 netlink_delinearize: release last register on exit d6fdb0d8 sets_with_ifnames: add test case for concatenated range 88b2345a segtree: add pretty-print support for wildcard strings in concatenated sets 806ab081 netlink: swap byteorder for host-endian concat data c224aa6b intervals: deletion should adjust range not yet in the kernel ea1f1c9f optimize: memleak in statement matrix 0a6dbfce optimize: merge nat rules with same selectors into map 743b0e81 optimize: do not clone unsupported statement c8b35039 optimize: incorrect logic in verdict comparison fc4da141 src: fix always-true assertions d1289bff intervals: set on EXPR_F_KERNEL flag for new elements in set cache 721b9dec tests: add concat test case with integer base type subkey 22b750aa src: allow use of base integer types as set keys in concatenations 3ed9fada intervals: build list of elements to be added from cache e45b4939 intervals: fix deletion of multiple ranges with automerge 3b7b22ae intervals: add elements with EXPR_F_KERNEL to purge list only ea31855d netlink: remove unused argument from helper function 48204bd7 intervals: Simplify element sanity checks ab1b21be intervals: unset EXPR_F_KERNEL for adjusted elements e0beff27 src: restore interval sets work with string datatypes 3e8d934e intervals: support to partial deletion with automerge 7a6e1604 evaluate: allow for zero length ranges 3da9643f intervals: add support to automerge with kernel elements 7b061e63 mnl: update mnl_nft_setelem_del() to allow for more reuse fdb8e0ff src: remove rbtree datastructure 81e36530 src: replace interval segment tree overlap and automerge f1cc44ed src: add EXPR_F_KERNEL to identify expression in the kernel ad43b84e segtree: add support for get element with sets that contain ifnames 06db2308 segtree: use correct byte order for 'element get' 4c6681a7 tests: add testcases for interface names in sets 5e393ea1 segtree: add string "range" reversal support 2fb4d7ea src: make interval sets work with string datatypes 403936c1 evaluate: string prefix expression must retain original length ada50f84 segtree: split prefix and range creation to a helper function ae7d32fc evaluate: keep prefix expression length d2b23984 evaluate: make byteorder conversion on string base type a no-op c36ecfc2 tests: py: Add meta time tests without 'meta' keyword 6fa4ff56 tests: py: Don't colorize output if stderr is redirected f561a0cc tests: monitor: Hide temporary file names from error output 75fea8a5 tests: py: extend meta time coverage 4460b839 meta: fix compiler warning in date_type_parse() 02100978 meta: time: use uint64_t instead of time_t 4e0026dc include: add missing `#include` ab74fb5b examples: add .gitignore file bcad4761 tests: py: add inet/vmap tests 214494aa optimize: Restore optimization for raw payload expressions 82762ab6 src: allow to use integer type header fields via typeof set declaration 64bb3f43 src: allow to use typeof of raw expressions in set declaration ff0f30e3 expression: typeof verdict needs verdict datatype 60f5c107 src: copy field_count for anonymous object maps as well 4cf97abf rule: Avoid segfault with anonymous chains 4e718641 evaluate: init cmd pointer for new on-stack context 1ea71c23 optimize: do not assume log prefix 3f36cc6c optimize: do not merge unsupported statement expressions 19960c8d optimize: incorrect assert() for unexpected expression type 3de1dbd2 optimize: more robust statement merge with vmap 99eb4696 optimize: fix vmap with anonymous sets e8f0fa21 scanner: Fix for ipportmap nat statements 59d184be scanner: dup, fwd, tproxy: Move to own scopes 069a0450 scanner: meta: Move to own scope 2165324d scanner: at: Move to own scope a67fce7f scanner: nat: Move to own scope 578467c1 scanner: policy: move to own scope a1669709 scanner: flags: move to own scope 020372d9 scanner: reject: Move to own scope 543bf3c2 scanner: import, export: Move to own scopes 88105810 scanner: reset: move to own Scope 8a7e430a scanner: monitor: Move to own Scope e5547017 scanner: rt: Extend scope over rt0, rt2 and srh 04c95f14 scanner: type: Move to own scope 62a95698 scanner: dst, frag, hbh, mh: Move to own scopes a060d912 scanner: ah, esp: Move to own scopes 4e215fdf scanner: osf: Move to own scope 5166b298 scanner: dccp, th: Move to own scopes 3e04a6e2 scanner: udp{,lite}: Move to own scope bbdcfbfa scanner: comp: Move to own scope. 232f2c32 scanner: synproxy: Move to own scope 26b53653 scanner: tcp: Move to own scope f5722119 scanner: igmp: Move to own scope a7d8cca9 scanner: icmp{,v6}: Move to own scope 5d837d27 src: add tcp option reset support 1d507ce7 build: explicitly pass --version-script to linker e98a9b83 libnftables.map: export new nft_ctx_{get,set}_optimize API 9eb98b3b tests: add test case for flowtable with owner flag 18a08fb7 examples: compile with `make check' and add AM_CPPFLAGS Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: bsap18x0: specify FIS directory location in dtsTomasz Maciej Nowak2022-06-244-90/+1
| | | | | | | | | The redboot-fis parser has option to specify the location of FIS directory, use that, instead of patching the parser to scan for it, and specifying location in kernel config. Tested-by: Brian Gonyer <bgonyer@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-29 17:08:32 +0000