aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mvebu: tidy up support for GL.iNet GL-MV1000Adrian Schmutzler2020-04-275-22/+15
| | | | | | | | | | | | | | | | | This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000: - apply alphabetic sorting in multiple files - use armada-3720 prefix for DTS like for other devices - fix vendor capitalization for model in DTSes - remove trivial comment in DTS files - use DEVICE_VENDOR/DEVICE_MODEL - remove redundant SUPPORTED_DEVICES - use SOC instead of DEVICE_DTS - remove empty line at EOF Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm53xx: 5.4: enable NANDDENG Qingfang2020-04-261-1/+4
| | | | | | | NAND driver was dropped in the 5.4 bump, so enable it back Fixes: 50c6938b95a0 ("bcm53xx: add v5.4 support") Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* mvebu: add support for GL.iNet GL-MV1000Li Zhang2020-04-265-1/+344
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for GL-MV1000. Specification: - SOC: Marvell Armada 88F3720 (1GHz) - Flash: 16MB (W25Q128FWSIG) - RAM: 1GB DDR4 - Ethernet: 3x GE (1 WAN + 2 LAN) - EMMC: 8GB EMMC (KLM8G1GETF-B041) - MicroSD: 1x microSD slot - USB: 1x USB 2.0 port(TypeA),1x USB 3.0 port(TypeC) - Button: 1x reset button,1x slide switch - LED: 3x greed LED - UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND) Update firmware instructions ============================ In the compiled,please gzip -d xxx.img.gz,then update firmware on uboot web. Signed-off-by: Li Zhang <li.zhang@gl-inet.com> [Copied dts file to files-5.4] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* toolchain/gcc: eliminate uClibc atexit hackRosen Penev2020-04-261-9/+2
| | | | | | | | This seems to be over 10 years old. It doesn't seem to be needed anymore. Tested on malta with uClibc (selected BROKEN). Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: support intel X7xx 10/40GbE adaptersXiaobo Tian2020-04-261-0/+42
| | | | | | Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com> [Add i40evf/i40evf.ko and setect CONFIG_IAVF] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: backport fix for non-regular inodes on f2fsMatt Merhar2020-04-261-0/+69
| | | | | | | | | | | | | | | Upstream commit dda9f4b9ca ("f2fs: fix to skip verifying block address for non-regular inode"). On 4.14, attempting to perform operations on a non-regular inode residing on an f2fs filesystem, such rm-ing a device node, would fail and lead to a warning / call trace in dmesg. This fix was already applied to other kernels upstream - including 4.19, from which the patch was taken. More info at https://bugzilla.kernel.org/show_bug.cgi?id=202495. Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* uboot-envtools: fix domywifi_dw33d Bad CRC errorweidong jia2020-04-261-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | The current dw33d partition index has changed, this patch solves this problem. old partition layout dev: size erasesize name mtd0: 00040000 00010000 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00fa0000 00010000 "oem-firmware" mtd3: 00010000 00010000 "art" mtd4: 00500000 00020000 "kernel" mtd5: 05b00000 00020000 "ubi" mtd6: 02000000 00020000 "oem-backup" new partition layout dev: size erasesize name mtd0: 00500000 00020000 "kernel" mtd1: 05b00000 00020000 "ubi" mtd2: 02000000 00020000 "oem-backup" mtd3: 00040000 00010000 "u-boot" mtd4: 00010000 00010000 "u-boot-env" mtd5: 00fa0000 00010000 "oem-firmware" mtd6: 00010000 00010000 "art" Signed-off-by: weidong jia <jwdsccd@gmail.com>
* uboot-envtools: update to 2020.04Lucian Cristian2020-04-261-7/+8
| | | | | | also revert to directly download the archive from https Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* u-boot.mk: switch download to httpsLucian Cristian2020-04-261-1/+2
| | | | | | | ftp can cause problems on some networks switch primary download location to https and add another mirror Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* tools/mkimage: update to 2020.04Lucian Cristian2020-04-267-241/+113
| | | | | | | | | also change the download source to https and add a mirror drop merged patches Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com> [Add extra changes to compile on FreeBSD, merge two patches] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: ath10k: increase rx buffer size to 2048Linus Lüssing2020-04-262-1/+38
| | | | | | | | | | | | | | | | | | | | | | | Before, only frames with a maximum size of 1528 bytes could be transmitted between two 802.11s nodes. For batman-adv for instance, which adds its own header to each frame, we typically need an MTU of at least 1532 bytes to be able to transmit without fragmentation. This patch now increases the maxmimum frame size from 1528 to 1656 bytes. Tested with two ath10k devices in 802.11s mode, as well as with batman-adv on top of 802.11s with forwarding disabled. Fix originally found and developed by Ben Greear. Link: https://github.com/greearb/ath10k-ct/issues/89 Link: https://github.com/greearb/ath10k-ct/commit/9e5ab25027e0971fa24ccf93373324c08c4e992d Cc: Ben Greear <greearb@candelatech.com> Signed-off-by: Linus Lüssing <ll@simonwunderlich.de> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* perf: build with NO_LIBCAP=1Yangbo Lu2020-04-261-0/+1
| | | | | | | | | Build with NO_LIBCAP=1. This is to resolve build issue. Package perf is missing dependencies for the following libraries: libcap.so.2 Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* gdb: disable gdbserver for arcLuiz Angelo Daros de Luca2020-04-261-0/+1
| | | | | | | | | | Although gdb is supported, gdbserver is still not. checking whether gdbserver is supported on this host... no Build breaks as gdbserver executable is not found during packaging. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* ramips: remove unnecessary DEVICE_PACKAGES for Belkin F7C027Sungbo Eo2020-04-261-1/+0
| | | | | | | kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and Belkin F7C027 does not have a USB port anyway. Just drop it. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix SUPPORTED_DEVICES for Mercury MAC1200R v2Sungbo Eo2020-04-261-1/+0
| | | | | | | | Currently SUPPORTED_DEVICES only contains the old device string. Fix it by removing the first assignment. Fixes: c2334ad60dc8 ("ramips/mt76x8: Synchronize Makefiles with DTS compatible") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* oxnas: move service file to correct placeSungbo Eo2020-04-261-0/+0
| | | | | | | This service file has been misplaced from the very beginning. Fixes: dcc34574efba ("oxnas: bring in new oxnas target") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: netdev: fix kmod-sfp symbolsDavid Bauer2020-04-261-2/+2
| | | | | | Fixes: ec2f7a47d379 ("kernel: add module to support SFP cages") Signed-off-by: David Bauer <mail@david-bauer.net>
* relayd: bump to version 2020-04-25Kevin Darbyshire-Bryant2020-04-261-3/+3
| | | | | | | | f4d759b dhcp.c: further improve validation Further improve input validation for CVE-2020-11752 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* umdns: update to version 2020-04-25Kevin Darbyshire-Bryant2020-04-261-3/+3
| | | | | | | | | | | cdac046 dns.c: fix input validation fix Due to a slight foobar typo, failing to de-reference a pointer, previous fix not quite as complete as it should have been. Improve CVE-2020-11750 fix Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* x86: fix unusable squashfs images by adding missing paddingPetr Štetiar2020-04-261-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It was reported, that after image generation rework x86-64-generic-squashfs-rootfs.img image won't boot on XenServer x86_64 anymore: F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x84289960) F2FS-fs (xvda): Can't find valid F2FS filesystem in 1th superblock F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x4e8ee223) F2FS-fs (xvda): Can't find valid F2FS filesystem in 2th superblock List of all partitions: ca00 4207 xvda driver: vbd No filesystem could mount root, tried: ext3 ext2 ext4 squashfs iso9660 f2fs Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(202,0) So lets fix this by adding back padding which was introduced in commit a17d9482f5e2 ("x86: image: fix small disk space in squashfs overlay"). Ref: FS#3036 Fixes: 258f070d1a4f ("x86: fix missing squashfs and ext4 rootfs images") Fixes: cb007a7bf619 ("x86: switch image generation to new code") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: netdev: fix kmod-sfp description capitalizationDavid Bauer2020-04-261-1/+1
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: netdev: add phylink dependency for sfpDavid Bauer2020-04-261-1/+1
| | | | | | Fixes: ec2f7a47d379 ("kernel: add module to support SFP cages") Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: netdev: add kmod-phylinkDavid Bauer2020-04-261-0/+16
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: enable SFP port for Ubiquiti ER-X-SFPRené van Dorst2020-04-253-3/+64
| | | | | | | | | | | | | | | SFP cage of this device is connected via a AT8031 phy to port 5 of the switch. This phy act as a RGMII-to-SerDes converter. Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus. SFP cage also has module detect pin which is connected to I2C gpio expander. With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port. NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding! This means that some SGMII modules can work and only at forced 1GBit/full-duplex! Signed-off-by: René van Dorst <opensource@vdorst.com>
* kernel: add module to support SFP cagesRené van Dorst2020-04-252-1/+21
| | | | | | Enables kernel SFP case support. Signed-off-by: René van Dorst <opensource@vdorst.com>
* ramips: phy: at803x: support RGMII-to-SerDes and SFP supportDENG Qingfang2020-04-251-0/+141
| | | | | Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: René van Dorst <opensource@vdorst.com>
* kernel: backport support for clause 37 1000Base-X auto-negotiationDENG Qingfang2020-04-251-0/+199
| | | | | | | This patch is needed for clause 37 1000Base-X encoding used in many SFP modules. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: René van Dorst <opensource@vdorst.com>
* kernel: bump 5.4 to 5.4.35Petr Štetiar2020-04-252-3/+3
| | | | | | | | | Refreshed one patch. Run tested: qemu-x86-64 Build tested: x86/64, imx6, sunxi/a53, rockchip/armv8 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* imx6: add back perf monitor related config symbolPetr Štetiar2020-04-251-0/+1
| | | | | | | | | Commit 0543eb111081 ("imx6: 5.4: add missing kernel perf monitor symbol") has added missing kernel config symbol FSL_IMX8_DDR_PMU which is exposed only when building perf, so add it back. Fixes: 8d9b36270b1f ("imx6: refresh kernel config") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* procd: extend requirejail attribute handlingDaniel Golle2020-04-251-3/+3
| | | | | | | | e2ed964 jail: don't fail unless requirejail is set 17e7ae7 jail: don't load libpreload-seccomp.so if it doesn't exist Fixes openwrt/packages#11913 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: fix alphabetical order in 02_networkDavid Bauer2020-04-241-11/+11
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix QCA953x DDR and GPIO compatible bindingsDavid Bauer2020-04-241-2/+2
| | | | | | | The memory as well as GPIO controller had the wrong SoC name used for their compatible binding. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: correct QCA9550 machine compatible bindingDavid Bauer2020-04-2414-14/+14
| | | | | | | Some boards using a QCA9556 or QCA9558 had their machine compatible binding incorrectly set to qca,qca9557. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: rename qca9557.dtsi to qca955x.dtsiDavid Bauer2020-04-2426-29/+29
| | | | | | | | | | | There are at least 3 different chips in the Scorpion series of SoCs. Rename the common DTSI to better reflect it's purpose for the whole series. Also rename the compatible bindings from qca,ar9557 and qca,qca9557 to qca,qca9550. Signed-off-by: David Bauer <mail@david-bauer.net>
* ltq-adsl(-fw): Makefile clean-up and fixesAdrian Schmutzler2020-04-243-10/+10
| | | | | | | | | | | | | | | This fixes a few minor issues (partially cosmetic) in ltq-adsl and ltq-adsl-fw Makefiles: - fix PKG_SOURCE_URL and switch to https - remove non-existant FW_NAME variable - fix package name for config inclusion - fix config symbol for debugging Fixes: 1d0a9d0c0470 ("move ltq-adsl") Cc: John Crispin <john@phrozen.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: move tplinkpart.c parser to patchesAdrian Schmutzler2020-04-243-253/+462
| | | | | | | | | | | | | Between 4.19 and 5.4, mtd parsers have been moved to "parsers" subdirectory. Like for myloader.c in the previous patch, this patch moves tplinkpart.c to the kernel patches, so the code and the kernel includes are at the same location and the path can be adjusted per kernel. While at it, remove some outdated kernel version switches from the C code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: fix include of myloader.o since kernel 5.4Adrian Schmutzler2020-04-246-208/+569
| | | | | | | | | | | | | | | | | | | | | | Between 4.19 and 5.4, mtd parsers have been moved to "parsers" subdirectory. Based on this, the selection of myloader.o in OpenWrt was also moved to that subdirectory, while the Kconfig and our local myloader.c file remained in /drivers/mtd. This resulted in linking errors like the following (on ath25@5.4): make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ... needed by 'drivers/mtd/parsers/built-in.a'. Stop. make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2 make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2 Since myloader.c is not too big, this patch moves it to the kernel patches, allowing to adjust the path for kernel 5.4 and keeping Makefiles and file paths better in sync. Other patches have been refreshed accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: replace "+@" IPV6 dependency by "+"Adrian Schmutzler2020-04-241-1/+1
| | | | | | | | | | The combination +@IPV6:kmod-ipsec6 is not valid, the +a:b syntax implies the @. Fix it. Fixes: 2e6b6f9fcaae ("kernel: add @IPv6 dependency to ipv6 modules") Reported-by: Oldřich Jedlička (@oldium) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove config-4.14 for mt7621/mt76x8Adrian Schmutzler2020-04-232-547/+0
| | | | | | | | | | | mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their DTS(I) files are incompatible to kernel 4.14. Remove the corresponding kernel config files to signal that more boldly and to prevent accidentally patching the wrong kernel when pulling in older config patches. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeon: use kernel version 5.4 for testingAdrian Schmutzler2020-04-231-0/+1
| | | | | | Tested on EdgeRouter Lite (by Daniel Engberg) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeon: update config for kernel 5.4Daniel Engberg2020-04-231-14/+24
| | | | | | | | Update config with make kernel_oldconfig. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [split patch, redo kernel_oldconfig, add description] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeon: refresh patches for kernel 5.4Daniel Engberg2020-04-233-5/+5
| | | | | | | | Refresh patches to make them apply to kernel 5.4. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [split patch, refresh on newer kernel, add description] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeon: copy files to kernel 5.4Daniel Engberg2020-04-234-0/+389
| | | | | | | | Copy config and patches to kernel 5.4. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [split patch, fix patches-5.4 dirname, add description] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: disable the unused pcie port for elecom wrc-2533gentFelix Fietkau2020-04-221-4/+0
| | | | | | Fixes MSI support for the primary device Signed-off-by: Felix Fietkau <nbd@nbd.name>
* fstools: update to the latest versionFelix Fietkau2020-04-221-3/+3
| | | | | | | | | | 84965b92f635 blockd: print symlink error code and string message 62c578c22f9d blockd: report "target" path as "mount" for autofs available mounts d1f1f2b38fa1 block: remove mount target file if it's a link 830441d790d6 blockd: remove symlink linkpath file if it's a dir or link c80f7002114f libfstools/mtd: attempt to read from OOB data if empty space is found Signed-off-by: Felix Fietkau <nbd@nbd.name>
* openssl: bump to 1.1.1gPetr Štetiar2020-04-211-2/+2
| | | | | | | | Fixes NULL dereference in SSL_check_chain() for TLS 1.3, marked with high severity, assigned CVE-2020-1967. Ref: https://www.openssl.org/news/secadv/20200421.txt Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 5.4 to 5.4.34Petr Štetiar2020-04-2110-33/+33
| | | | | | | | | Refreshed patches. Run tested: qemu-x86-64, apalis, a64-olinuxino Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* imx6: refresh kernel configKoen Vandeputte2020-04-211-170/+5
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* base-files: ensure VERBOSE is setAlexander Couzens2020-04-211-1/+1
| | | | | | | If not set, it shows the following error sh: out of range Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* lantiq/fritz 7312: set maximum speed to 100 mbitAlexander Couzens2020-04-211-0/+1
| | | | | | | | The fritz 7312 does not support 1000 gbit. Advertising it makes it worse. Some NIC will change to 1000 gibt and turn off and on again for ever. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-14 11:29:50 +0000