aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* qoriq: switch to kernel 5.15Stijn Tintel2022-12-141-2/+1
| | | | | | | | | The testing kernel has been running fine for months on a rather complex network setup, with one exception being a crash in __xfrm_state_delete(). This crash has been fixed in kernel 5.15.82, so let's switch the qoriq target to kernel 5.15 by default. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* mac80211: fix connecting multiple wds stations to an APFelix Fietkau2022-12-142-1/+26
| | | | | | A faulty check prevented the AP_VLAN interfaces from being brought up Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: 5.15: standardize wpq864 partition tableChristian Marangi2022-12-141-43/+43
| | | | | | | | | | Compex WPQ864 contains a non standard partition table. Each partition node should be named partition and should contain a valid reg. Fix an extra "-" present after the reg for SBL2_1 partition. Also add "0:" to each qcom default partition following smem naming. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq806x: 5.15: fix wrong boot-partitions values for split partitionsChristian Marangi2022-12-143-3/+3
| | | | | | | | | | | | | The refreshed patch actually use the format of <start size start size> instead of <start end start end>. This cause boot fail since the rootfs can't be mounted with these wrong values. Fix it to the correct format in each affected dts. Fixes: #11498 Fixes: 6134ba4a34db ("ipq806x: 5.15: add boot-partitions binding to fix block warning") Tested-by: Matt Buczko <mbuczko@hotmail.com> # Askey RT4230W Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* libpcap: add support for B.A.T.M.A.N. AdvancedLinus Lüssing2022-12-141-0/+642
| | | | | | | | | | | | | | | | | | | | | | This adds support for the layer 2 mesh routing protocol B.A.T.M.A.N. Advanced. "batadv" can be used to filter on batman-adv packets. It also allows later filters to look at frames inside the tunnel when both "version" and "type" are specified. Documentation for the batman-adv protocol can be found at the following locations: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/networking/batman-adv.rst https://www.open-mesh.org/ -- This is a backport of the following upstream pull request: https://github.com/the-tcpdump-group/libpcap/pull/980 -> "Add support for B.A.T.M.A.N. Advanced #980" Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
* ath79: add support for TP-Link CPE605-v1Andrew Cameron2022-12-134-0/+45
| | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 23dBi high-gain directional antenna and a dedicated metal reflector - Power, LAN, WLAN5G green LEDs - 3x green RSSI LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ramips: add support for Etisalat S3Mikhail Zhilkin2022-12-136-3/+266
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1x USB3.0 Button: 2 buttons (Reset & WPS) LEDs: - 1x Status (RGB) - 1x 2.4G (blue, hardware, mt76-phy0) - 1x 5G (blue, hardware, mt76-phy1) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Login to the router web interface under admin account 2. Navigate to Settings -> Configuration -> Save to Computer 3. Decode the configuration. For example, using cfgtool.py tool (see related section): cfgtool.py -u configurationBackup.cfg 4. Open configurationBackup.xml and find the following line: <PARAMETER name="Password" type="string" value="<your router serial \ is here>" writable="1" encryption="1" password="1"/> 5. Insert the following line after and save: <PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/> 6. Encode the configuration. For example, using cfgtool.py tool: cfgtool.py -p configurationBackup.xml 7. Upload the changed configuration (configurationBackup_changed.cfg) to the router 8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where ETxxxxxxxxxx is the serial number from the backplate label) 9. Navigate to Settings -> WAN -> Add static IP interface (e.g. 10.0.0.1/255.255.255.0) 10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22, 10.0.0.0/255.255.255.0 and interface created before 11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the ethernet cable to the WAN port of the router 12. Connect to the router using SSH shell under SuperUser account 13. Run in SSH shell: sh 14. Make a mtd backup (optional, see related section) 15. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 16. Login to the router web interface under admin account 17. Remove dots from the OpenWrt factory image filename 18. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 10.0.0.2 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses ------------- +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | *:50 | | WAN | label + 11 | *:5b | | 2g | label + 2 | *:52 | | 5g | label + 3 | *:53 | +-----+------------+---------+ The label MAC address was found in Factory 0x21000 cfgtool.py ---------- A tool for decoding and encoding Sercomm configs. Link: https://github.com/r3d5ky/sercomm_cfg_unpacker Co-authored-by: Karim Dehouche <karimdplay@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* mac80211: add a fix for a crash in __ieee80211_rx_h_amsduFelix Fietkau2022-12-131-0/+413
| | | | | | Fix initialization of rx->link_sta Signed-off-by: Felix Fietkau <nbd@nbd.name>
* treewide: remove DRIVER_11N_SUPPORTAndre Heider2022-12-1314-36/+21
| | | | | | | | | | | | hostapd's compile time option CONFIG_IEEE80211N was removed almost 3 years ago, 80.211n/HT is always included since then. Noticed because `hostapd -v11n` confusingly returned an error. See hostapd's commit: f3bcd69603 "Remove CONFIG_IEEE80211N build option" Signed-off-by: Andre Heider <a.heider@gmail.com>
* hostapd: fix 350-nl80211_del_beacon_bss.patchAndre Heider2022-12-131-1/+1
| | | | | | | | | | | | | | | | | Pass the expected struct: ../src/drivers/driver_nl80211.c: In function 'wpa_driver_nl80211_del_beacon': ../src/drivers/driver_nl80211.c:2945:31: warning: passing argument 1 of 'nl80211_bss_msg' from incompatible pointer type [-Wincompatible-pointer-types] 2945 | msg = nl80211_bss_msg(drv, 0, NL80211_CMD_DEL_BEACON); | ^~~ | | | struct wpa_driver_nl80211_data * ../src/drivers/driver_nl80211.c:695:50: note: expected 'struct i802_bss *' but argument is of type 'struct wpa_driver_nl80211_data *' 695 | struct nl_msg * nl80211_bss_msg(struct i802_bss *bss, int flags, uint8_t cmd) | ~~~~~~~~~~~~~~~~~^~~ Fixes: 35ff1affe8 "hostapd: update to 2022-05-08" Signed-off-by: Andre Heider <a.heider@gmail.com>
* hostapd: remove an unused function from ubus.cAndre Heider2022-12-131-26/+0
| | | | | | | eee80211_frequency_to_channel() isn't used anymore, which is a leftover from: 2a31e9ca97 "hostapd: add op-class to get_status output" Signed-off-by: Andre Heider <a.heider@gmail.com>
* ath9k: add missing dependency on random coreFelix Fietkau2022-12-131-1/+1
| | | | | Reported-by: Hartmut Birr <e9hack@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* generic: move pending 870 ca8210 fix crash patch to backportChristian Marangi2022-12-132-0/+0
| | | | | | | Patch got merged upstream in kernel 6.1. Move it to backport to better track it. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* generic: fix wrong PTR_ERR use in of net mac address ascii patchChristian Marangi2022-12-132-4/+4
| | | | | | | | | | | | | | | | | | | | nvmem_cell_read return a pointer error when an error occurs. Currently we convert the pointer error to an int while the rest of the function return a void* and expcet an error pointer. Fix this PTR_ERR msuse fixing compilation warning. Fixes the following compilation warning: net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address': net/ethernet/eth.c:547:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion] 547 | return PTR_ERR(mac); | ^~~~~~~~~~~~ net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address_ascii': net/ethernet/eth.c:564:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion] 564 | return PTR_ERR(mac_ascii); | ^~~~~~~~~~~~~~~~~~ Fixes: 7b863af180da ("kernel: move mac-address-ascii patches to generic") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* gemini: Set proper default networksLinus Walleij2022-12-121-0/+15
| | | | | | | | Some Gemini devices are NAS type devices and need to ask for DHCP IP on eth0. Some has a LAN/WAN setup. Add sensible defaults for all known devices. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* uml: switch to Kernel 5.15Christian Lamparter2022-12-121-2/+1
| | | | | | Switch over from testing version. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: remove MR32's openwrt specific patch for LEDsChristian Lamparter2022-12-121-28/+0
| | | | | | | | The patch managed to sneak into v5.15 whereas it was properly deleted for v5.10. Fixes: 8f6e2bb17886 ("bcm53xx: remove MR32's specific get_leds_dt code") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* sunxi: fix sunxi-ir kconfig and descriptionChukun Pan2022-12-123-2/+15
| | | | | | | | | | | Removed a20 in description, since it only works for a10, a13 and a31. Also refreshed kernel config. Fixes: #10466 Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (moved fixes, refreshed, added CONFIG_DVB_USB=n) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* sunxi: modules: remove useless AddDepends/rtcChukun Pan2022-12-121-4/+2
| | | | | | | | | AddDepends/rtc has been removed in commit 3da7fe6, same here. Fixes: 3da7fe6 ("kernel: remove useless AddDepends/rtc abstraction") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (RTC_SUPPORT - though this is implied by the TARGET_sunxi) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* sunxi: fix 253-sunxi-h5-add-support-for-nanopi-r1s-h5 patch offsetChristian Lamparter2022-12-121-1/+1
| | | | | | | This showed up in the log: |Hunk #1 succeeded at 555 (offset -83 lines). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: modules/lib-lz4: add lz4hc_compressTony Butler2022-12-113-1/+8
| | | | | | | | | enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config this only adds the `lz4hc_compress` module, and has no effect on the `lz4_decompress` module which already supports any flavor Signed-off-by: Tony Butler <spudz76@gmail.com>
* lantiq: vr9: include usb driver for fritz 7430Tony Butler2022-12-111-1/+2
| | | | | | | | | | Reported by user: missing driver for USB; add to image definition https://github.com/openwrt/openwrt/issues/11326 Resolves: #11326 Signed-off-by: Tony Butler <spudz76@gmail.com> Acked-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* kernel: Refresh kernel 5.10Hauke Mehrtens2022-12-111-4/+4
| | | | | | | Make the patches apply cleanly again. Fixes: 8327e0fb72f0 ("kernel: backport the dev_set_threaded export to 5.10") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* rtl8812au-ct: fix build with newer backports cfg80211 apiFelix Fietkau2022-12-111-0/+56
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* wolfssl: fix build with /dev/cryptoChukun Pan2022-12-111-0/+33
| | | | | | | | | | Backport upstream patch to fix build error when /dev/crypto enabled. https://github.com/wolfSSL/wolfssl/commit/dc9f46a3be00b5e82684a158605189d1278e324c Fixes: #10944 Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* umbim: Allow roaming and partner connectionsJulio Gonzalez Gil2022-12-111-6/+25
| | | | | | | | | | Allow registration if the SIM is roaming or partner mode, by adding two new options to the protocol. Until now, such registration failed because umbim returns exit codes 4 and 5 for such situations. Signed-off-by: Julio Gonzalez Gil <git@juliogonzalez.es>
* ipq40xx: fix usb driver not loaded for GL-A1300Weiping Yang2022-12-111-0/+8
| | | | | | | This patch enables USB support for the GL.iNet GL-A1300 Repair the usb driver startup phase is not loaded Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* libtracefs: update to 1.6.2Nick Hainke2022-12-111-2/+2
| | | | | | | | 378a9dd libtracefs: version 1.6.2 e6daa60 libtracefs: Add unit test to test mounting of tracefs_{tracing,debug}_dir() 32acbbf libtracefs: Have tracefs_{tracing,debug}_dir() mount {tracefs,debugfs} if not mounted Signed-off-by: Nick Hainke <vincent@systemli.org>
* kernel: bump 5.10 to 5.10.158John Audia2022-12-116-10/+10
| | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.157John Audia2022-12-1122-91/+58
| | | | | | | | | | | | | | | Manually rebased: backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch hack-5.10/645-netfilter-connmark-introduce-set-dscpmark.patch Removed upstreamed: pending-5.10/706-netfilter-nf_flow_table-add-missing-locking.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.157&id=b8e494240e69f91517256adcd6fda62d0671772d Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: add symbol in generic config for 5.10.157John Audia2022-12-111-0/+1
| | | | | | Add CONFIG_INET_TABLE_PERTURB_ORDER=16 to generic config Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.82John Audia2022-12-1117-204/+204
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.81John Audia2022-12-1149-180/+144
| | | | | | | | | | | | | | | | | | | | Manually rebased: backport-5.15/715-v6.0-net-ethernet-mtk_eth_soc-add-the-capability-to-run-m.patch hack-5.15/645-netfilter-connmark-introduce-set-dscpmark.patch[1] Removed upstreamed: pending-5.15/701-netfilter-nf_flow_table-add-missing-locking.patch[2] All other patches automatically rebased 1. Rebase by Kevin 'ldir' Darbyshire-Bryant<ldir@darbyshire-bryant.me.uk> 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.81&id=8db9e60cdfdae5b049e32e82323da8f0f989066a Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: add symbol in generic config for 5.15.81John Audia2022-12-111-0/+1
| | | | | | Add CONFIG_INET_TABLE_PERTURB_ORDER=16 to generic config Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: backport the dev_set_threaded export to 5.10Felix Fietkau2022-12-101-0/+24
| | | | | | Fixes mt76 build error Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport mtk_wed.h from 5.15 to 5.10Felix Fietkau2022-12-101-0/+209
| | | | | | Fixes mt76 build error Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mt76: update to the latest versionFelix Fietkau2022-12-102-1611/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ec46d7486ab9 sync with upstream 2575de3aea33 wifi: mt76: mt7921: introduce chanctx support 473cebb3c3e1 wifi: mt76: fix bandwidth 80MHz link fail in 6GHz band de3e77227f62 wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices f0c191a9f6cd wifi: mt76: mt7996: add missing argument in mt7996_queue_rx_skb() d3838a52df62 wifi: mt76: mt7996: enable use_cts_prot support 98492dff3bec wifi: mt76: mt7996: enable ack signal support 2a41e7a82f86 wifi: mt76: mt7996: add support to configure spatial reuse parameter set 194cb3392829 mt76: mt7915: add missing of_node_put() f91d6f3b73ac wifi: mt76: mt7921s: fix slab-out-of-bounds access in sdio host 1ce4970d799f wifi: mt76: mt7915: fix mt7915_rate_txpower_get() resource leaks 379f3fc0fc43 wifi: mt76: mt7996: fix insecure data handling of mt7996_mcu_ie_countdown() 233c272f0f86 wifi: mt76: mt7996: fix insecure data handling of mt7996_mcu_rx_radar_detected() 5616c4cc1d5d wifi: mt76: mt7996: fix integer handling issue of mt7996_rf_regval_set() f9598e6d4c2c wifi: mt76: mt7915: split mcu chan_mib array up b252d94bd763 wifi: mt76: mt7915: check return value before accessing free_block_num f1cc3696d725 wifi: mt76: mt7996: check return value before accessing free_block_num b94ba58fa698 wifi: mt76: mt7915: check the correctness of event data 35843a1670c0 wifi: mt76: mt7915: drop always true condition of __mt7915_reg_addr() 01a256c1dc41 wifi: mt76: mt7996: drop always true condition of __mt7996_reg_addr() 5185bbab8953 wifi: mt76: mt7996: fix endianness warning in mt7996_mcu_sta_he_tlv eeb6949c4d06 wifi: mt76: mt76x0: fix oob access in mt76x0_phy_get_target_power 063823aba978 wifi: mt76: mt7921: add support to update fw capability with MTFG table a44109267e4e wifi: mt76: mt7996: fix unintended sign extension of mt7996_hw_queue_read() be5dbb781068 wifi: mt76: mt7915: fix unintended sign extension of mt7915_hw_queue_read() adf9042b6f63 wifi: mt76: fix coverity uninit_use_in_call in mt76_connac2_reverse_frag0_hdr_trans() 551201379efe wifi: mt76: move leds field in leds struct 14fbb6d6e85e wifi: mt76: move leds struct in mt76_phy 81edc468fc62 wifi: mt76: mt7915: enable per-phy led support bbad827e447f wifi: mt76: mt7615: enable per-phy led support 8e7e7e52fc09 wifi: mt76: dma: do not increment queue head if mt76_dma_add_buf fails 95c66d651133 wifi: mt76: handle possible mt76_rx_token_consume failures 52d04463a66e wifi: mt76: dma: rely on queue page_frag_cache for wed rx queues 7fae1de12ae7 wifi: mt76: mt7921: resource leaks at mt7921_check_offload_capability() Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: update to linux 6.1-rc8Felix Fietkau2022-12-10127-10176/+4391
| | | | | | This should help stay in sync with upstream development Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mt76: update to version 2022-12-01Felix Fietkau2022-12-101-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 3deafbad7061 wifi: mt76: mt7915: fix uninitialized irq_mask 6ca31dc64da4 wifi: mt76: mt7921: introduce remain_on_channel support 7962005b0734 wifi: mt76: connac: rework macros for unified command 3b2882ca704e wifi: mt76: connac: update struct sta_rec_phy c4d46cb1dd45 wifi: mt76: connac: rework fields for larger bandwidth support in sta_rec_bf 532c322fd72f wifi: mt76: connac: add more unified command IDs 4c43e060726b wifi: mt76: connac: introduce unified event table 4c423058920d wifi: mt76: connac: add more bss info command tags 143d7ab8ef92 wifi: mt76: connac: add more starec command tags 733ef9887b2c wifi: mt76: connac: introduce helper for mt7996 chipset 8e309b5560e1 wifi: mt76: mt7921: fix wrong power after multiple SAR set d791ed1f5877 wifi: mt76: mt7915: add missing MODULE_PARM_DESC 3b8eed9c3866 wifi: mt76: mt7915: add support to configure spatial reuse parameter set 417cca39bab2 wifi: mt76: introduce rxwi and rx token utility routines 629f8631f54f wifi: mt76: add WED RX support to mt76_dma_{add,get}_buf 13c2dc8993b6 wifi: mt76: add WED RX support to mt76_dma_rx_fill 86e94f4162b7 wifi: mt76: add WED RX support to dma queue alloc 1361519851f3 wifi: mt76: add info parameter to rx_skb signature a2e5e0667553 wifi: mt76: connac: introduce mt76_connac_mcu_sta_wed_update utility routine f38faf294310 wifi: mt76: mt7915: enable WED RX support a887a5feb3d1 wifi: mt76: mt7915: enable WED RX stats 4c23061ebcfc wifi: mt76: mt7915: add basedband Txpower info into debugfs a9c88ded5cac wifi: mt76: mt7915: enable .sta_set_txpwr support 2c172bb6cd9f wifi: mt76: mt7915: fix band_idx usage 1b88dd07f153 linux-firmware: update firmware for MT7915 6196f6080506 linux-firmware: update firmware for MT7916 daae6ca5d81f linux-firmware: update firmware for MT7986 e7a9f7a0440c wifi: mt76: mt7915: fix unused-but-set warning 340f3be65397 wifi: mt76: fix coverity overrun-call in mt76_get_txpower() aa7132da0326 wifi: mt76: mt7915: fix endianness of mt7915_mcu_set_obss_spr_pd() a36017d09324 wifi: mt76: mt7921: Add missing __packed annotation of struct mt7921_clc 66dc48bea883 wifi: mt76: do not send firmware FW_FEATURE_NON_DL region fa79eeeadc2d mt76: mt7915: Fix PCI device refcount leak in mt7915_pci_init_hif2() ff94604b2edd wifi: mt76: mt7915: introduce mt7915_get_power_bound() 5082a58f8082 wifi: mt76: mt7915: enable per bandwidth power limit support a7b915302147 wifi: mt76: mt7915: fix scene detection flow of spatial reuse 525592c28d6b wifi: mt76: mt7915: rely on band_idx of mt76_phy cdd7229e769b wifi: mt76: mt7915: mmio: fix naming convention Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: use wpa_supplicant for unencrypted mesh connectionsFelix Fietkau2022-12-103-3/+7
| | | | | | It's more reliable than using iw Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: fix Teltonika RUT230 v1 MAC assignmentDavid Bauer2022-12-091-2/+2
| | | | | | | | | The MAC-Address setup for the Teltonika RUT230 v1 was swapped for the LAN / WAN ports. Also the Label-MAC was assigned incorrect, as the WiFi MAC is printed on the case as part of the SSID, however only the LAN MAC-Address is designated as a MAC-Address. Signed-off-by: David Bauer <mail@david-bauer.net>
* realtek: update GPIO bindings for DGS-1210-10PJan-Niklas Burfeind2022-12-091-4/+26
| | | | | | | | | | | | | | | | add three missing LEDs - PoE-Max - Link/Act - PoE add two missing buttons - mode - reset The last was dropped in commit 61a3d0075b15 ("realtek: update GPIO bindings in the dts files in dts-5.10") Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* realtek: d-link: add support for dgs-1210-28mp-fAndreas Böhler2022-12-084-90/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | General hardware info: ---------------------- D-Link DGS-1210-28MP rev. F1 is a switch with 24 ethernet ports and 4 combo ports, all ports Gbit capable. It is based on a RTL8382 SoC @ 500MHz, DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE capable with a total PoE power budget of 370W. Power over Ethernet: -------------------- The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports each. They are controlled by a Nuvoton MCU. In order to enable PoE, the realtek-poe package is required. It is installed by default, but currently it requires the manual editing of /etc/config/poe. Keep in mind that the port number assignment does not match on this switch, alway 8 ports are in reversed order: 8-1, 16-9 and 24-17. LEDs and Buttons: ----------------- On stock firmware, the mode button is supposed to switch the LED indicators of all port LEDs between Link Activity and PoE status. The currently selected mode is visualized using the respective LEDs. PoE Max indicates that the maximum PoE budget has been reached. Since there is currently no support for this behavior, these LEDs and the mode button can be used independently. Serial connection: ------------------ The UART for the SoC (115200 8N1) is available via unpopulated standard 0.1" pin header marked J6. Pin1 is marked with arrow and square. Pin 1: Vcc 3.3V Pin 2: Tx Pin 3: Rx Pin 4: Gnd OEM installation from Web Interface: ------------------------------------ 1. Make sure you are booting using OEM in image 2 slot. If not, switch to image2 using the menus System > Firmware Information > Boot from image2 Tools > reboot 2. Upload image in vendor firmware via Tools > Backup / Upgrade Firmware > image1 3. Toogle startup image via System > Firmware Information > Boot from image1 4. Tools > reboot Other installation methods not tested, but since the device shares the board with the DGS-1210-28, the following should work: Boot initramfs image from U-Boot: --------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28mp-f-initramfs-kernel.bin` command 5. Boot the image with `bootm` command Signed-off-by: Andreas Böhler <dev@aboehler.at>
* uboot-bcm4908: update to the latest genericRafał Miłecki2022-12-081-3/+3
| | | | | | 4435700d18 Remove redundant YYLOC global declaration Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ustream-ssl: update to Git version 2022-12-07Hauke Mehrtens2022-12-081-4/+4
| | | | | | | | | 9217ab4 ustream-openssl: Disable renegotiation in TLSv1.2 and earlier 2ce1d48 ci: fix building with i.MX6 SDK 584f1f6 ustream-openssl: wolfSSL: provide detailed information in debug builds aa8c48e cmake: add a possibility to set library version Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* CI: kernel: don't checkout and install feedsChristian Marangi2022-12-071-1/+0
| | | | | | | We don't need to checkout feed and install feeds for kernel tests. This saves up to 2 minutes for each target kernel build test. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* CI: build: skip sdk adapt to external toolchain on cache hitChristian Marangi2022-12-071-1/+1
| | | | | | | | | | | | On cache hit, skip sdk adapt to external toolchain. This is needed because we cache the already extracted sdk and that is already adapted to be used as external toolchain. Rerunning the adap step will result in the test to fail for missing file as the file are already got wrapped to the external toolchain format. Fixes: 42f0ab028e2e ("CI: build: fix use of sdk as toolchain") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: add support for Wavlink WS-WN572HP3 4GJan-Niklas Burfeind2022-12-073-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wavlink WS-WN572HP3 4G is an 802.11ac dual-band outdoor router with LTE support. Specifications; * Soc: MT7621DAT * RAM: 128MiB * Flash: NOR 16MiB GD-25Q128ESIG3 * Wi-Fi: * MT7613BEN: 5GHz * MT7603EN: 2.4GHz * Ethernet: 2x 1GbE * USB: None - only used internally * LTE Modem: Quectel EC200T-EU * UART: 115200 baud * LEDs: * 7 blue at the front * 1 Power * 2 LAN / WAN * 1 Status * 3 RSSI (annotated 4G) * 1 green at the bottom (4G LED) * Buttons: 1 reset button Installation: * press and hold the reset button while powering on the device * keep it pressed for ten seconds * connect to 192.168.10.1 via webbrowser (chromium/chrome works, at least Firefox 106.0.3 does not) * upload the sysupgrade image, confirm the checksum, wait 2 minutes until the device reboots Revert to stock firmware: * same as installation but use the recovery image for WL-WN572HP3 Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* comgt-ncm: add support for quectel modem EC200T-EUJan-Niklas Burfeind2022-12-072-0/+22
| | | | | | | | | context_type is an integer mapping of pdptype: 1: IPV4 2: IPV6 3: IPV4V6 Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* ramips: define loadaddr for all UniFi devicesDavid Bauer2022-12-071-0/+2
| | | | | | | | Define the load-address for the DTB of all Ubiquiti UniFi devices using FIT images. From the GPL code we can assume these boards are affected by the same relocating issue with the vendor bootloader. Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-19 16:37:19 +0000