aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* odhcp6c: update to git HEADHans Dedecker2020-12-051-3/+3
| | | | | | | | | | faed29a dhcpv6: only refresh timers when reconfigure is valid 9c50975 dhcpv6: fix printing identity association id a7b2221 dhcpv6: avoid sending continuous renew/rebind messages d7afa2b dhcpv6: add extra syslog info traces f5728e4 odhcp6c_find_entry: exclude priority from the list of fields that must match Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* build: make testing kernel decompression more portableFelix Fietkau2020-12-051-1/+1
| | | | | | | On non-GNU systems, zcat often does not handle gzip decompression. Use gzip -dc like the regular unpack command Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: remove an unused callback from the ip17xx switch driverFelix Fietkau2020-12-052-34/+0
| | | | | | Also remove the leftover kernel hack that adds support for it Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm63xx: Add support for D-Link DSL-2750u rev C1Ahmed Naseef2020-12-0513-9/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the D-Link DSL-2750u rev C1. (https://deviwiki.com/wiki/D-Link_DSL-2750U_rev_C1) It uses the same hardware as ADB P.DG A4001N. CPU: Broadcom BCM63281 (320 MHz) RAM: 32M (Winbond W9725G6JB) Flash: 8M (MXIC MX25L6445E) Ethernet: 4x 100 Mbps Wireless: 802.11b/g/n: BCM43225 USB: 1x 2.0 Flash instructions: 1. Assign static IP 192.168.1.100 to PC 2. Unplug the power source 3. Press the RESET button at the router, don't release it yet! 4. Plug the power source.Wait some seconds 5. Release the RESET button 6. Browse to http://192.168.1.1 7. Send the openwrt-bcm63xx-generic-DSL2750U-C1-squashfs-cfe.bin and wait some minutes until the firmware upgrade finish. Signed-off-by: Ahmed Naseef <naseefkm@gmail.com> [DTS improvements, proper board patch, refresh patches] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: A4001N A-000-1A1-AX: remove PSI (nvram) partitionDaniele Castro2020-12-051-6/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI) is a Telecom Italia braded router and it seems that there are no public available unbranded versions of this router. The stock Telecom Italia braded firmware has many partitions and the partition layout changes with every firmware relase. The PSI nvram partition is present in the stock firmware under the "UNKNOWN" name but it's empty, full of FFs. Since removing partitions does not cause problems with the stock firmware reflashing procedure, I removed from the dts the PSI nvram partition from OpenWrt, expanded the rootfs one and added the NVRAM partition contained in the cfe bootloader. Furthermore this router's flash needs to be entirely reprogrammed and a new generic bcm6328 cfe must be flashed to boot OpenWrt. The same process takes place when reflashing the stock firmware. Here follows the original flash layout for AGPWI_1.1.0_013, the last stock Telecom Italia braded firmware for which we have root credentials (admin/riattizzati). Flash layout: Section 00 Type BOOT Range 0x00000000-0x00020000 MaxSize 0x00020000 No more information. Section 01 Type IMAGE Range 0x00020000-0x007C0000 MaxSize 0x0079FF6C Uninitialized. Section 02 Type IMAGE Range 0x00800000-0x00FA0000 MaxSize 0x0079FF6C Uninitialized. Section 03 Type CONF Range 0x00FA0000-0x00FC0000 MaxSize 0x0001FF6C Size 0x0000841E Name 'rg_conf' Checksum 0x0041E03B Counter 0x0000051F Start Offset 0x00000000 Section 04 Type CONF Range 0x00FC0000-0x00FE0000 MaxSize 0x0001FF6C Size 0x0000838E Name 'rg_conf' Checksum 0x00419A5A Counter 0x00000522 Start Offset 0x00000000 Section 05 Type FACTORY Range 0x00FE0000-0x00FF0000 MaxSize 0x0000FF6C Size 0x00000554 Name 'rg_factory' Checksum 0x0001255E Counter 0x000004D3 Start Offset 0x00000000 Section 06 Type UNKNOWN Range 0x00FF0000-0x01000000 MaxSize 0x00010000 No more information. Total 7 sections found. The last AGPWI firmware relase should be AGPWI_4.0.6 and it has much more partitions than AGPWI_1.1.0_013. The cfe partition in the stock firmware is 0x00020000 bytes long unlike the OpenWrt dts in wich it's 0x00010000 bytes long because from 0x00010000 to 0x00020000 in the stock cfe there are only 00s and also because the cfe must anyway be reflashed with a generic bcm6328 cfe 0x00010000 bytes long to run OpenWrt. Signed-off-by: Daniele Castro <danielecastro@hotmail.it> [Amend commit, remove unneeded cfe_nvram partition] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: support xmit_more in BQLSieng Piaw Liew2020-12-051-0/+54
| | | | | | | | Support bulking hardware TX queue by using xmit_more. Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [Amend commit description, fix kernel xmit_more exceptions] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add BQL supportSieng Piaw Liew2020-12-051-0/+67
| | | | | | | | Add Byte Queue Limits support to reduce/remove bufferbloat in bcm63xx target. Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [Amend commit description] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath79: add support for TP-Link TL-WDR7500 v3Adrian Schmutzler2020-12-044-2/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | This ports support for the TP-Link TL-WDR7500 v3 from ar71xx to ath79. The basic features appear to be identical to the Archer C7 v1, however it has the (supported) QCA9880-BR4A chip of the C7 v2. Specifications: SoC: QCA9558 CPU: 720 MHz Flash: 8 MiB RAM: 128 MiB WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac Qualcomm Atheros QCA9880-BR4A Ethernet: 5x Gbit ports USB: 2x 2.0 ports Flashing instructions: Upload the factory image via the OEM firmware GUI. TFTP recovery appears to be available as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.81John Audia2020-12-0410-22/+22
| | | | | | | | | | | | | | All modifications made by update_kernel.sh/no human intervention needed Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [another refresh] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: drop redundant status for gpio/gpio0Adrian Schmutzler2020-12-0445-180/+0
| | | | | | | | | | The first gpio controller (gpio or gpio0) is always enabled by default in the SoC DTSI files. No need to set status=okay in the device DTS files a second time. Remove the redundant statements. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: drop num-cs for SPI controllerAdrian Schmutzler2020-12-04171-297/+3
| | | | | | | | None of the spi drivers on ath79 uses the num-cs property. Cc: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: remove num-chipselects from SPI controllerAdrian Schmutzler2020-12-049-14/+0
| | | | | | | | | | | | | | The num-chipselects property is only valid for bit-banged spi-gpio [1]. For the generic SPI controller bindings, num-cs would be the correct property [2]. Since num-cs is not required on ath79 either, just drop the lines. [1] https://www.kernel.org/doc/Documentation/devicetree/bindings/spi/spi-gpio.yaml [2] https://www.kernel.org/doc/Documentation/devicetree/bindings/spi/spi-controller.yaml Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* procd: output warning if user 'ubus' doesn't existDaniel Golle2020-12-041-3/+3
| | | | | | 6acc48c early: fall-back to run ubus as root if user can't be found Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ubus: make sure ubusd starts in case user 'ubus' doesn't existDaniel Golle2020-12-041-3/+3
| | | | | | d1d9ddf ubusd: attempt to create socket folder Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* x86: enable CONFIG_MMC_SDHCI_ACPI for x86_64Mengyang Li2020-12-031-0/+2
| | | | | | | | | | | | | | | | | | | | | Some x86_64 single board computer (including Atomic Pi) has onboard emmc, but requires CONFIG_MMC_SDHCI_ACPI driver to use or boot from it. Here is boot message for the mmc device [ 2.838008] mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA [ 2.857536] mmc1: SDHCI controller on ACPI [80860F14:01] using ADMA [ 2.950019] mmc0: new HS200 MMC card at address 0001 [ 3.158271] mmcblk0: mmc0:0001 M52516 14.6 GiB [ 3.170290] mmcblk0boot0: mmc0:0001 M52516 partition 1 4.00 MiB [ 3.177191] mmcblk0boot1: mmc0:0001 M52516 partition 2 4.00 MiB [ 3.183963] mmcblk0rpmb: mmc0:0001 M52516 partition 3 4.00 MiB, \ chardev (248:0) Other lines changed in this config file are introduced by menuconfig. Signed-off-by: Mengyang Li <mayli.he@gmail.com>
* base-files: informative service command in /etc/shinit. service command ↵Stan Grishin2020-12-032-6/+18
| | | | | | | | | | | | | | shows services enabled/disabled and running status, when the service command is invoked with no/invalid arguments, like this: Usage: service <service> [command] The following services are available: /etc/init.d/acme enabled stopped /etc/init.d/boot enabled stopped /etc/init.d/cron enabled running /etc/init.d/dnsmasq enabled running ... Signed-off-by: Stan Grishin <stangri@melmac.net>
* brcm63xx: add USB status LED in 01_leds for ADP P.DG A4001NDaniele Castro2020-12-041-1/+2
| | | | | | Add a status LED in 01_leds for USB 2-1 connected devices. Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
* build: Extract trusted-firmware-a.mkHauke Mehrtens2020-12-022-87/+164
| | | | | | | | | | | | | | | | | | The include/trusted-firmware-a.mk file is based on the include/u-boot.mk file and should be used to build a Trusted Firmware-A (TFA) which was previously named Arm trusted firmware. This is useful for targets where the TFA is board specific like for Marvell SoCs and probably also NXP Layerscape SoCs. This also makes use of this abstraction in the arm-trusted-firmware-mvebu package to build board specific ATF binaries. The ATF binaries will be automatically activated and build when the board is selected in the normal build or all boards are selected. This should also activate the build when build bot creates images. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* toolchain: musl: refresh patchesHauke Mehrtens2020-12-022-15/+6
| | | | | | Refresh the musl patches Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: remove ar934x MDIO reset from MAC nodeDavid Bauer2020-12-021-2/+2
| | | | | | | | | | | Remove the MDIO reset from the MAC mode for the AR934x SoC family. The reset is currently also defined for the MDIO node, where the reset is acquired exclusively. In case the ethernet node is enabled, this triggers a warning, as the reset is already acquired by the MAC. Signed-off-by: David Bauer <mail@david-bauer.net>
* bcm63xx: enetsw: switch to netdev_alloc_skb_ip_alignSieng Piaw Liew2020-12-021-0/+37
| | | | | | | | | | | | | | | | | | | Increases packet processing performance by 30%. Tested on BCM6328 320 MHz and iperf3 -M 512 for packet/sec performance. Before: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 120 MBytes 33.7 Mbits/sec 277 sender [ 4] 0.00-30.00 sec 120 MBytes 33.5 Mbits/sec receiver After: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 155 MBytes 43.3 Mbits/sec 354 sender [ 4] 0.00-30.00 sec 154 MBytes 43.1 Mbits/sec receiver Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [Merge patches, amend commit and add patch description] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: batch process RX pathSieng Piaw Liew2020-12-021-0/+53
| | | | | | | | | | | | | | | | | | | Use netif_receive_skb_list to batch process skb in RX. Tested on BCM6328 320 MHz using iperf3 -M 512, increasing performance by 12.5%. Before: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 120 MBytes 33.7 Mbits/sec 277 sender [ 4] 0.00-30.00 sec 120 MBytes 33.5 Mbits/sec receiver After: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 136 MBytes 37.9 Mbits/sec 203 sender [ 4] 0.00-30.00 sec 135 MBytes 37.7 Mbits/sec receiver Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [Amend commit description] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath79: enable LNA for all ar9344 TPLink CPE devicesThomas Huehn2020-12-022-16/+16
| | | | | | | | | | | | The TPLink CPE devices CPE210/CPE510 based on ar9344 have a build-in Low Noise Amplifier on both of the 2x2 mimo rx chains. This patch activates those two LNAs in the respective receiving chains and hence improves the RX sensitivity by about 20dB. Tested on CPE510 v2 & v3. Signed-off-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de> Acked-by: Robert Marko <robimarko@gmail.com>
* netifd: update to the latest versionFelix Fietkau2020-12-021-3/+3
| | | | | | | | | | | d6bd1047d004 vlandev: dump vlan id in device status e0c838bd06a6 vlandev: support bridge-vlan aliases in the vid config parameter 574dc4a17105 system-dummy: print configured mac address 14f0e8ff928f system-linux: simplify mask check in system_if_apply_settings 524310276f20 system-linux: move device settings handling to device.c 42c48866f1c1 config: parse default mac address from board.json Signed-off-by: Felix Fietkau <nbd@nbd.name>
* realtek: fix SFP ports on the dlink 10port switchJohn Crispin2020-12-022-2/+14
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* realtek: add zyxel_gs1900-10hp supportJohn Crispin2020-12-023-0/+296
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* realtek: cleanup package selectionJohn Crispin2020-12-022-4/+2
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* realtek: clean up board.json generationJohn Crispin2020-12-021-31/+47
| | | | | | | | | | | | In this new setup the switch is treated as wan, lan1.100 is used as our mgmt vlan. The board mac is applied to eth0, switch and switch.1 The board mac is assigned with the LA bit set to all lan ports while incrementing it. Signed-off-by: John Crispin <john@phrozen.org>
* base-files: allow setting device and bridge macsJohn Crispin2020-12-022-9/+42
| | | | | | | | | Add code for setting mac addresses inside board.json and rendering them out to uci. On switches we want to have a unique MAC on each port. With 48 port switches that would require 48 device sections in /etc/config/network. Doing so via board.json is easier. Signed-off-by: John Crispin <john@phrozen.org>
* uboot-envtools: add support for the realtek targetJohn Crispin2020-12-021-0/+29
| | | | | | On most boards the MAC is located inside the u-boot-env. Signed-off-by: John Crispin <john@phrozen.org>
* README: mv logo.svg include/logo.{png,svg}Paul Spooren2020-12-013-1/+1
| | | | | | | | | | | | Some Git hoster (e.g. sr.ht) disable hosting of svg images (xml) to avoid XSS attacks. To show the logo correctly on all code hosters use a "safe" PNG image. Also move logo(s) to include/ folder to lower autocomplete churn with the `logs/` folder. While at it, replace absolute logo path and make it relative, as this may break other code hosters as well. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ath79: restore sysupgrade support for ja76pf2 and routerstationsTomasz Maciej Nowak2020-12-014-4/+16
| | | | | | | | | | | | | | | | | | | Because the bug described in FS#2428 has been fixed with bf2870c1d9e1 ("kernel: fix mtd partition erase < parent_erasesize writes") these devices can now safely do sysupgrade. Restore sysupgrade support disabled in: 0cc87b3bacee ("ath79: image: disable sysupgrade images for routerstations and ja76pf2") cc5256a8bfa0 ("ath79: base-files: disable sysupgrade for routerstations and ja76pf2") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> [move Build block, remove check-size argument, wrap sysupgrade line, make commit message easier to read] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: wlr-7100: remove device variant indicatorTomasz Maciej Nowak2020-12-012-2/+1
| | | | | | | As reported by user, the same image works on both device variants which are v1 001 and v1 002. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* tegra: sysupgrade: write additional information to log outputTomasz Maciej Nowak2020-12-011-4/+3
| | | | | | | | This will explain what is actually occuring on dd invocations. Additionally remove comments for steps which are described by printed statements anyway. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* tegra: sysupgrade: use v function for writing logsTomasz Maciej Nowak2020-12-011-6/+6
| | | | | | Sync with x86 target changes. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* mvebu: sysupgrade: write additional information to log outputTomasz Maciej Nowak2020-12-011-4/+3
| | | | | | | | This will explain what is actually occuring on dd invocations. Additionally remove comments for steps which are described by printed statements anyway. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* mvebu: sysupgrade: use v function for writing logsTomasz Maciej Nowak2020-12-012-7/+7
| | | | | | Sync with x86 target changes. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* procd: update to git HEADDaniel Golle2020-11-301-3/+3
| | | | | | | | f3c3563 jail: improve seccomp BPF generator f67a66f jail: always call cgroups_free() 4625350 jail: seccomp: improve code readability Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* busybox: add check for capabilities fileDaniel Golle2020-11-302-2/+2
| | | | | | | | | Similar to the previous commit adding a check to the init script of umdns, do a similar change for sysntpd, just to be on the safe side. Inspired-by: 520403cd49 ("umdns: add check for seccomp list") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* umdns: add check for seccomp listJan Pavlinec2020-11-302-2/+2
| | | | | | | | This should fix an issue when user have a router with enabled seccomp and tries to run umdns package which was build with SDK with disabled seccomp support. Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
* generic: ipeth: fix iOS 14 tetheringDavid Bauer2020-11-301-0/+44
| | | | | | | | This fixes tethering with devices using iOS 14. Prior to this patch, connections to remote endpoints were not possible while data transfers between the OpenWrt device and the iOS endpoints worked fine. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: Add cell_density data rates optionNick Lowe2020-11-301-13/+54
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a cell_density option to configure data rates for normal, high and very high cell density wireless deployments. The purpose of using a minimum basic/mandatory data rate that is higher than 6 Mb/s, or 5.5 Mb/s (802.11b compatible), in high cell density environments is to transmit broadcast/multicast data frames using less airtime or to reduce management overheads where significant co-channel interference (CCI) exists and cannot be avoided. Caution: Without careful design and validation, configuration of a too high minimum basic/mandatory data rate can sacrifice connection stability or disrupt the ability to reliably connect and authenticate for little to no capacity benefit. This is because this configuration affects the ability of clients to hear and demodulate management, control and broadcast/multicast data frames. Deployments that have not been specifically designed and validated are usually best suited to use 6, 12 and 24 Mb/s as basic/mandatory data rates. Only usually seek to configure a 12 Mb/s, or 11 Mb/s (802.11b compatible), minimum basic/mandatory rate in high cell density deployments that have been designed and validated for this. For many deployments, the minimum basic/mandatory data rate should not be configured above 12 Mb/s to 18 Mb/s, 24 Mb/s or higher. Such a configuration is only appropriate for use in very high cell density deployment scenarios. A cell_density of Very High (3) should only be used where a deployment has a valid use case and has been designed and validated specifically for this use, nearly always with highly directional antennas - an example would be stadium deployments. For example, with a 24 Mb/s OFDM minimum basic/mandatory data rate, approximately a -73 dBm RSSI is required to decode frames. Many clients will not have roamed elsewhere by the time that they experience -73 dBm and, where they do, they frequently may not hear and be able to demodulate beacon, control or broadcast/multicast data frames causing connectivity issues. There is a myth that disabling lower basic/mandatory data rates will improve roaming and avoid sticky clients. For 802.11n, 802.11ac and 802.11ax clients this is not correct as clients will shift to and use lower MCS rates and not to the 802.11b or 802.11g/802.11a rates that are able to be used as basic/mandatory data rates. There is a myth that disabling lower basic/mandatory data rates will ensure that clients only use higher data rates and that better performance is assured. For 802.11n, 802.11ac and 802.11ax clients this is not correct as clients will shift around and use MCS rates and not the 802.11b or 802.11g/802.11a rates that able to be used as basic/mandatory data rates. Cell Density 0 - Disabled (Default) Setting cell_density to 0 does not configure data rates. This is the default. 1 - Normal Cell Density Setting cell_density to 1 configures the basic/mandatory rates to 6, 12 and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower than the minimum basic/mandatory rate are not offered. Setting cell_density to 1 configures the basic/mandatory rates to the 5.5 and 11 Mb/s DSSS rates where legacy_rates is 1. Supported rates lower than the minimum basic/mandatory rate are not offered. 2 - High Cell Density Setting the cell_density to 2 configures the basic/mandatory rates to the 12 and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower than the minimum basic/mandatory rate are not offered. Setting the cell_density to 2 configures the basic/mandatory rates to the 11 Mb/s DSSS rate where legacy_rates is 1. Supported rates lower than the minimum basic/mandatory rate are not offered. 3 - Very High Cell Density Setting the cell_density to 3 configures the basic/mandatory rates to the 24 Mb/s OFDM rate where legacy_rates is 0. Supported rates lower than the minimum basic/mandatory rate are not offered. Setting the cell_density to 3 only has effect where legacy_rates is 0, else this has the same effect as being configured with a cell_density of 2. Where specified, the basic_rate and supported_rates options continue to override both the cell_density and legacy_rates options. Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
* base-files: fix alias more to properly detect /usr/bin/moreHuangbin Zhan2020-11-281-1/+1
| | | | | | Package more is installed to /usr/bin rather than /bin. Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
* lantiq: fix build of squashfs imagesAleksander Jan Bajkowski2020-11-295-5/+5
| | | | | | | | | | | | This patch fixes build of squashfs image on lantiq. Currently the FEATURE variable is overwritten by the subtarget. Fixes: FS#3480 Fixes: f1c652337628 ("lantiq: clean up target/subtarget features") Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> [reformat Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ASUS RT-N56U B1Pavel Chervontsev2020-11-283-0/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621ST (880 MHz) FLASH: 16 MiB (Macronix MX25L12835FM2I-10G) RAM: 128 MiB (Nanya NT5CB64M16FP-DH) WiFi: MediaTek MT7603EN bgn 2x2:2 WiFi: MediaTek MT7612EN an 2x2:2 BTN: Reset, WPS LED: - Power - WiFi 2.4 GHz - WiFi 5 GHz - WAN - LAN {1-4} - USB {1-2} UART: UART is present as pin hole next to the aluminium capacitor. 3V3 - RX - GND - TX / 115200-8N1 3V3 is the nearest on the aluminium capacitor and nut hole (pin1). USB: 2 ports POWER: 12VDC, 1.5A (Barrel 5.5x2.1) Installation: Via TFTP: Set your computers IP-Address to 192.168.1.75 Power up the Router with the Reset button pressed. Release the Reset button after 5 seconds. Upload OpenWRT sysupgrade image via TFTP: tftp -4 -v -m binary 192.168.1.1 -c put IMAGE MAC addresses: 0x4 *:98 2g/wan, label 0x22 *:9c 0x28 *:98 0x8004 *:9c 5g/lan Though addresses are written to 0x22 and 0x28, it appears that the vendor firmware actually only uses 0x4 and 0x8004. Thus, we do the same here. Signed-off-by: Pavel Chervontsev <cherpash@gmail.com> [add MAC address overview, add label-mac-device, fix IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath10k-firmware: remove unused packageÁlvaro Fernández Rojas2020-11-281-182/+0
| | | | | | | All firmwares were added to linux-firmware, so there's no need to keep this package definitions. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath10k-ct-firmware: switch to linux-firmware board binariesÁlvaro Fernández Rojas2020-11-281-135/+37
| | | | | | | | | | Instead of duplicating board firmware binaries, which are exactly the same as the ones from linux-firmware, add dependencies and remove duplicated downloads. Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* linux-firmware: ath10k: add board firmware packagesÁlvaro Fernández Rojas2020-11-282-16/+46
| | | | | | | Split ath10k firmwares into board and firmware packages. This way we can add dependencies to ath10k-ct firmware packages. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* cmake.mk,rules.mk: fix host builds using CMake and ccachePetr Štetiar2020-11-282-2/+17
| | | | | | | | | | | | | | Commit f98878e4c17d ("cmake.mk: set C/CXX compiler for host builds as well") has introduced regression as it didn't taken usage of ccache into the account so fix it by handling ccache use cases as well. In order to get this working we need to export HOSTCXX_NOCACHE in rules.mk as well. Fixes: f98878e4c17d ("cmake.mk: set C/CXX compiler for host builds as well") Reported-by: Ansuel Smith <ansuelsmth@gmail.com> Tested-by: Ansuel Smith <ansuelsmth@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* libnetfilter-cthelper: removeRosen Penev2020-11-281-72/+0
| | | | | | | conntrack was moved to packages where this is used. This will be moved there as well. Signed-off-by: Rosen Penev <rosenp@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-01 01:47:31 +0000