aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add basic common recipe for nand flash devicesShiji Yang2023-05-181-207/+47
| | | | | | | | These same codes are repeated for many devices now, it's better to move them to shared definition. This commit also add the missing KERNEL_SIZE of the ZyXEL NR7101 and ZyXEL LTE3301-PLUS. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: set default BLOCKSIZE to 64k for nor flash devicesShiji Yang2023-05-187-74/+2
| | | | | | | | | In kernel 5.15, the default erase sector size of the nor flash has been switched from 4k to 64k. This may cause the configuration not be preserved across upgrades. To avoid this issue, change the default BLOCKSIZE to 64k. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: enable variable sector size erasure for all subtargetShiji Yang2023-05-184-2/+4
| | | | | | | | | Make use of minor sector size (4k) on supported flash chips to improve spi read/write performance. Tested on ramips/mt7628: Motorola MWR03 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* kernel: add MODULE_ALLOW_BTF_MISMATCH optionTianling Shen2023-05-181-0/+10
| | | | | | | | | | | BTF mismatch can occur for a separately-built module even when the ABI is otherwise compatible and nothing else would prevent successfully loading. Add a new config to control how mismatches are handled. By default, preserve the current behavior of refusing to load the module. If MODULE_ALLOW_BTF_MISMATCH is enabled, load the module but ignore its BTF information. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ipq-wifi: drop upstreamed board-2.binChristian Lamparter2023-05-183-63/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The BDFs for the: Aruba AP-365 Devolo Magic 2 WiFi next Edgecore ECW5410 Edgecore OAP100 Extreme Networks WS-AP3915i GL.iNet GL-A1300 GL.iNet GL-AP1300 GL.iNet GL-S1300 Linksys EA8300 Linksys WHW03v2 Nokia Wi4A AC400i P&W R619AC Pakedge WR-1 Qxwlan E2600AC C1 Sony NCP-HG100/Cellular Teltonika RUTX10 ZTE MF18A were upstreamed to the ath10k-firmware repository and landed in linux-firmware.git. Furthermore the BDFs for the: 8devices Habanero 8devices Jalapeno Qxwlan E2600AC C2 have been updated. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mvebu: use PHY LED trigger for speed LEDs on FortiGate 50EINAGAKI Hiroshi2023-05-182-9/+12
| | | | | | | | | | | | | Use <mdio>:<addr>:<speed> trigger instead of netdev(link) trigger for Fortinet FortiGate 50E, to indicate link speed on the each phys. 1000 Mbps: Green 100 Mbps : Amber 10 Mbps : (turn off) Fixes: 102dc5a62506 ("mvebu: add support for Fortinet FortiGate 50E") Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mvebu: cortexa9: enable Ethernet PHY LED triggerINAGAKI Hiroshi2023-05-181-0/+1
| | | | | | | To use <mdio>:<addr>:<speed> trigger for LEDs, enable PHY LED trigger (CONFIG_LED_TRIGGER_PHY). Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* download: create immutable subversion checkout archiveTomasz Maciej Nowak2023-05-181-1/+1
| | | | | | | | | On each generation of the archive check sum will differ, because when checking out subversion repository, current date is used for directories creation. Force tar to assign creation date of the last revision for all items inside archive. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* scripts/gen_image_generic.sh: allow passing in partition offsetTim Harvey2023-05-181-1/+1
| | | | | | | | | | Allow passing in an optional offset (PARTOFFSET) for the first partition. If not specified this will default to 256K (512 blocks) as it has before. For example if you want to start partition data at a 16M offset instead of 256K, specify 'PARTOFFSET=16M'. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* octeontx: kernel: add USB storage boot supportTim Harvey2023-05-181-0/+2
| | | | | | | | | Enable BLK_DEV_SD and USB_STORAGE so that rootfs can be on a USB Mass Storage device. This increases the kernel Image by 66KiB Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* imx: kernel: add USB storage boot supportTim Harvey2023-05-181-0/+2
| | | | | | | | | Enable BLK_DEV_SD and USB_STORAGE so that rootfs can be on a USB Mass Storage device. This adds 23KiB to the compressed kernel size Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* nu801: add kmod-leds-uleds to MR26 + MR18Christian Lamparter2023-05-182-2/+2
| | | | | | | | | | | | | | support for MR18 and MR26 was developped before the userspace nu801 was integrated with x86's MX100 into OpenWrt. The initial nu801 + kmod-leds-uleds caused build-bot errors. The solution that worked for the MX100 was to include the kmod-leds-uleds to the device platform module. Thankfully, the MR26 and MR18 can just add the uleds package to the DEVICE_PACKAGES variable. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* libxml2: update to 2.11.3Nick Hainke2023-05-182-4/+4
| | | | | | | | | | | | Changelog: - https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.10.4 - https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.11.0 - https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.11.1 - https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.11.2 - https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.11.3 Fixes: CVE-2023-28484 CVE-2023-29469 Signed-off-by: Nick Hainke <vincent@systemli.org>
* ramips: rename to D-Team Newifi D2 and Lenovo Newifi D1Arınç ÜNAL2023-05-183-6/+6
| | | | | | | Rename Newifi D2 to D-Team Newifi D2, and Newifi D1 to Lenovo Newifi D1. Let's not make naming exceptions because of marketing whims. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: add support for TOZED ZLT S12 PROArınç ÜNAL2023-05-184-0/+262
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a TOZED TL70-C cellular modem which supports the NCM mode. The stock firmware does SIM locking on the modem by stopping dialing when a different PLMN is detected. This is not the case on OpenWrt. Specifications: - CPU: MediaTek MT7621AT - RAM: 256MB DDR3 - NOR Flash: MX25L12833FM2I 16MB SPI Flash - Wi-Fi 2.4Ghz: MT7603E - Wi-Fi 5Ghz: MT7612E - Switch: MT7530 4x 1Gbit Ports - WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem - USB: 1x optional USB2.0 external port - Switches/Buttons: WPS, Reset, Power Switch - LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone Installation and TFTP Recovery: - Connect to serial console. - Boot initramfs image by choosing option 1 when U-Boot prompts. - Install sysupgrade image via OpenWrt. Serial Pins: Located at the bottom right when looking from the front, right under the Reset/WPS buttons. The pinout from the left is: - RX - GND - TX Baudrate is 115200. When connecting from a powered off state, disconnect RX as it blocks the boot process. Link: http://www.sztozed.com/en/contents/58/84.html Co-developed-by: Andre Cruz <me@1conan.com> Signed-off-by: Andre Cruz <me@1conan.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* comgt-ncm: add support for UNISOC SL8563 based TOZED TL70-CArınç ÜNAL2023-05-181-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | TOZED TL70-C is an LTE CAT6 cellular modem based on UNISOC SL8563. UNISOC was formerly called Spreadtrum hence the manufacturer name detected on the modem is spreadtrum. The connect and disconnect commands bring up and down the usb0 interface. They are Base64 encoded as that's what the AT command accepts. The modem can do up to 4 APNs by bringing the USB interfaces, usb0 to usb3, up. Setting the USB interfaces up: connmanctl ndisdial AT^NDISDUN="usb0",1,1 connmanctl ndisdial AT^NDISDUN="usb1",1,2 connmanctl ndisdial AT^NDISDUN="usb2",1,3 connmanctl ndisdial AT^NDISDUN="usb3",1,4 Setting the USB interfaces down: connmanctl ndisdial AT^NDISDUN="usb0",0,1 connmanctl ndisdial AT^NDISDUN="usb1",0,2 connmanctl ndisdial AT^NDISDUN="usb2",0,3 connmanctl ndisdial AT^NDISDUN="usb3",0,4 Co-developed-by: Andre Cruz <me@1conan.com> Signed-off-by: Andre Cruz <me@1conan.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* base-files: add protocol ncm support for ucidef_set_interface()Arınç ÜNAL2023-05-181-0/+1
| | | | | | | Make it possible to set up a default network (interface) for devices with cellular modems using NCM. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* wwan: add Medion S4222 usb lte stickJoe Cooper2023-05-182-1/+6
| | | | | | | | add description for medion usb lte webstick Signed-off-by: Joe Cooper <highjagger+github@gmail.com> [bump PKG_RELEASE] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ucode: update to the latest versionTianling Shen2023-05-181-3/+3
| | | | | | | | | 8f78aff2cb68 ubus: support multiple call return values 51f4dba67313 ucode: also link libresolv if ns_initparse() is not found 5c7d07773a59 uci: fix ctx.commit() without arguments 5163867269fc Merge pull request #148 from jow-/uci-fix-commit Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* mediatek: remove left-over reference to make_gl_metadata.pyDaniel Golle2023-05-181-3/+1
| | | | | | | | When adding support for the GL.iNet GL-MT3000 a reference to the non-existent make_gl_metadata.py script was accidentally added. Remove it, flashing from vendor firmware also works fine without that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: Fix Wireless Frequencies for HYC-G920Muhammad AL-Qadhy2023-05-181-0/+2
| | | | | | Fix wireless frequencies to show correct wireless interfaces. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
* px5g-wolfssl: replace COMMITCOUNT with real PKG_RELEASETianling Shen2023-05-181-1/+1
| | | | | | Similar to the AUTORELEASE conversion process. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* treewide: replace AUTORELEASE with real PKG_RELEASETianling Shen2023-05-1858-58/+58
| | | | | | | | | | | | | | | | | | Based on Paul Fertser <fercerpav@gmail.com>'s guidance: Change AUTORELEASE in rules.mk to: ``` AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile)) ``` then update all affected packages by: ``` for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';); do make package/$i/clean done ``` Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* firmware-utils: update to latest HEADDavid Bauer2023-05-181-3/+3
| | | | | | | | | 02cdbc6 tplink-safeloader: add Archer AX23 v1.2 (RU) de36fa6 tplink-safeloader: add AX23 support-list entry 5f6fefd tplink-safeloader: order AX23 support-list 25131d6 tplink-safeloader: add Archer C59 / C60 CA ragion code Signed-off-by: David Bauer <mail@david-bauer.net>
* libselinux: update to 3.5Linhui Liu2023-05-181-6/+5
| | | | | | | | | | | | | Switch from libpcre to libpcre2. While working on it remove the double defined HOST_BUILD_DEPENDS section. Release Notes: https://github.com/SELinuxProject/selinux/releases/download/3.4/RELEASE-3.4.txt https://github.com/SELinuxProject/selinux/releases/download/3.5/RELEASE-3.5.txt Signed-off-by: Linhui Liu <liulinhui36@gmail.com> [depend on libpcre2] Signed-off-by: Nick Hainke <vincent@systemli.org>
* secilc: update to 3.5Linhui Liu2023-05-181-2/+2
| | | | | | | | Release Notes: https://github.com/SELinuxProject/selinux/releases/download/3.4/RELEASE-3.4.txt https://github.com/SELinuxProject/selinux/releases/download/3.5/RELEASE-3.5.txt Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
* policycoreutils: update to 3.5Linhui Liu2023-05-181-2/+2
| | | | | | | | Release Notes: https://github.com/SELinuxProject/selinux/releases/download/3.4/RELEASE-3.4.txt https://github.com/SELinuxProject/selinux/releases/download/3.5/RELEASE-3.5.txt Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
* libsemanage: update to 3.5Linhui Liu2023-05-181-2/+2
| | | | | | | | Release Notes: https://github.com/SELinuxProject/selinux/releases/download/3.4/RELEASE-3.4.txt https://github.com/SELinuxProject/selinux/releases/download/3.5/RELEASE-3.5.txt Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
* libsepol: update to 3.5Linhui Liu2023-05-181-2/+2
| | | | | | | | Release Notes: https://github.com/SELinuxProject/selinux/releases/download/3.4/RELEASE-3.4.txt https://github.com/SELinuxProject/selinux/releases/download/3.5/RELEASE-3.5.txt Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
* checkpolicy: update to 3.5Linhui Liu2023-05-181-2/+2
| | | | | | | | Release Notes: https://github.com/SELinuxProject/selinux/releases/download/3.4/RELEASE-3.4.txt https://github.com/SELinuxProject/selinux/releases/download/3.5/RELEASE-3.5.txt Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
* pcre: move package to packages feedNick Hainke2023-05-182-140/+0
| | | | | | | With the update of selinux no package depends anymore on pcre in the base repository. Move it to packages feed. Signed-off-by: Nick Hainke <vincent@systemli.org>
* pcre2: import pcre2 from packages feedNick Hainke2023-05-182-0/+138
| | | | | | | pcre2 is needed by newer selinux versions, so it needs to be in the base repository. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ci: fix check kernel patches jobPetr Štetiar2023-05-181-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the check fails due to the following error: warning: Not a git repository. Use --no-index to compare two paths outside a working tree usage: git diff --no-index [<options>] <path> <path> Thats likely caused by commit 1cb8cdbf0723 ("ci: use new buildbot worker images with Debian 11") which contains a patched Git version with CVE security fixes introduced in DLA-3239-2: Multiple issues were found in Git, a distributed revision control system. An attacker may cause other local users into executing arbitrary commands, leak information from the local filesystem, and bypass restricted shell. Note: Due to new security checks, access to repositories owned and accessed by different local users may now be rejected by Git; in case changing ownership is not practical, git displays a way to bypass these checks using the new "safe.directory" configuration entry. So lets opt-out of this new behavior by setting `safe.directory=*` and thus force Git to consider all Git repositories as safe regardless of their owner, since we need to trust those sources anyway and it should be likely more robust solution, then fiddling with filesystem permissions. Fixes: 1cb8cdbf0723 ("ci: use new buildbot worker images with Debian 11") References: https://www.debian.org/lts/security/2022/dla-3239-2 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mediatek: update patch add PWM support for MT7981Daniel Golle2023-05-181-119/+29
| | | | | | Update patch with version submitted upstream. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for the GL.iNet GL-MT3000Daniel Golle2023-05-184-3/+295
| | | | | | | | | | | | | | | | | | | | | | The MT-3000 is a pocket-sized Wi-Fi 6 router based on MediaTek MT7981. Specification: - SoC: MediaTek MT7981B - CPU: 2x 1.3 GHz Cortex-A53 - Flash: 256 MiB Macronix SPI NAND - RAM: 512 MiB Nanya DDR4 - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN) - Ethernet: - 1x 10/100/1000 Mbps built-in PHY (LAN) - 1x 10/100/1000/2500 Mbps MaxLinear GPY211 PHY (WAN) - USB 3.0 port - Buttons: 1 button, 1 switch - LEDs: 1x light-blue, 1x warm-white - Serial console: internal 4-pin header, 115200 8n1 - PWM controlled fan with tacho - Power: 5 VDC, 3 A (USB Type-C) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: fix mt7601u firmware path and refresh patchesDaniel Golle2023-05-186-8/+65
| | | | | | | Import patch fixing the updated firmware path of mt7601u.bin. Refresh patches while at it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Cudy WR3000 v1David Bauer2023-05-186-0/+318
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7981 WiSoC 256MB DDR3 RAM 16MB SPI-NOR (XMC XM25QH128C) MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5) UART: 115200 8N1 3.3V [LEDS] VCC-GND-RX-TX [ETH] Header is located below the heatsink Case ---- Unscrew the 4 bottom screws. Remove the top of the case by inserting a small screwdriver into the ventilation holes and lift the top cover. This works best by beginning near the ETH-ports. The top is clipped on the front near the LEDs with two plastic clips. The back has a single clip in the middle. Start at one of the back edges. MAC-Addresses ------------- 80:AF:CA:00:F9:C6 LAN 80:AF:CA:00:F9:C7 WAN 80:AF:CA:00:F9:C6 W2 82:AF:CA:30:F9:C6 W5 Installation ------------ 1. Connect to the serial port as described in the "Hardware" section. 2. Power on the device. Keep pressing the "0" key to enter the U-Boot shell. 3. Download the OpenWrt initramfs image. Place it on an TFTP server connected to the Cudy LAN ports. Make sure the server is reachable at 192.168.1.2. Rename the image to "cudy3000.bin" 4. Download and boot the OpenWrt initramfs image. $ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000 5. Transfer the OpenWrt sysupgrade image to the device using scp. Install with sysupgrade. Note: Cudy does not yet provide a image for disabling their signature-protection. This has happened in the past. Make sure to check the wiki for a possible easier installation method. Signed-off-by: David Bauer <mail@david-bauer.net>
* iwinfo: update to latest HEADDavid Bauer2023-05-181-3/+3
| | | | | | | c9f5c3f devices: add MediaTek MT7981 WMAC compatible b3888b2 devices: add compatible strings for Ralink WiSoCs Signed-off-by: David Bauer <mail@david-bauer.net>
* mt76: add MT7981 firmware packagesDavid Bauer2023-05-181-0/+16
| | | | | | Package the firmware required for MT7981 to bring up the radio. Signed-off-by: David Bauer <mail@david-bauer.net>
* mt76: update to latest HEADDavid Bauer2023-05-183-343/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 969b7b5e wifi: mt76: mt7915: add support for MT7981 cddbd796 linux-firmware: add firmware for MT7981 c69b0239 linux-firmware: update firmware for MT7921 WiFi device c85a0f2f mt7921: remove duplicated line 0cbe1376 wifi: mt76: mt7915: drop redundant prefix of mt7915_txpower_puts() b490c6c7 wifi: mt76: fix 6GHz high channel not be scanned db5a8f70 wifi: mt76: move shared mac definitions in mt76_connac2_mac.h 3963ab2f wifi: mt76: mt7921: get rid of eeprom.h c09f943d wifi: mt76: add mt76_connac_gen_ppe_thresh utility routine 28ea992c wifi: mt76: get rid of unused sta_ps callbacks 2936b036 wifi: mt76: add mt76_connac_irq_enable utility routine 482d2a76 wifi: mt76: move irq_tasklet in mt76_dev struct 88d1b002 wifi: mt76: mt7996: enable mesh HW amsdu/de-amsdu support 577fbd47 linux-firmware: update firmware for MT7916 32be54b5 linux-firmware: update firmware for MT7921 WiFi device 4e2fad04 linux-firmware: update firmware for MT7922 WiFi device f8793b1a linux-firmware: update firmware for MT7921 WiFi device 91e6ad2a linux-firmware: update firmware for MT7921 WiFi device b7a538a3 linux-firmware: update firmware for MT7922 WiFi device e3b5a8cc wifi: mt76: mt7996: enable configured beacon tx rate a18bf481 wifi: mt76: mt7996: enable BSS_CHANGED_MCAST_RATE support f863beed wifi: mt76: mt7996: enable BSS_CHANGED_BASIC_RATES support aedc10d5 wifi: mt76: connac: add nss calculation into mt76_connac2_mac_tx_rate_val() 84a227e5 wifi: mt76: connac: fix txd multicast rate setting a0657180 wifi: mt76: mt7921e: stop chip reset worker in unregister hook fd895347 wifi: mt76: mt7921e: improve reliability of dma reset c9fa8d64 wifi: mt76: mt7921: fix missing unwind goto in `mt7921u_probe` c1baa812 mt76: mt7921: fix kernel panic by accessing unallocated eeprom.data ca180889 wifi: mt76: move mcu_uni_event and mcu_reg_event in common code 98fbca7a wifi: mt76: mt7996: enable coredump support be1ff24e wifi: mt76: mt7996: add full system reset knobs into debugfs b7a6c0ef wifi: mt76: mt7996: enable full system reset support 46f28e75 wifi: mt76: mt7921: enable p2p support 6a7e41c3 wifi: mt76: mt7921e: Set memory space enable in PCI_COMMAND if unset 084e6de7 wifi: mt76: mt7921: use driver flags rather than mac80211 flags to mcu c66e7a1a wifi: mt76: mt7921: introduce mt7921_get_mac80211_ops utility routine 821caac5 wifi: mt76: mt7996: fix eeprom tx path bitfields 9ae2569b wifi: mt76: mt7996: remove mt7996_mcu_set_pm() 3244d176 wifi: mt76: mt7996: init mpdu density cap 210a558a wifi: mt76: mt7996: fix pointer calculation in ie countdown event 207c92bb wifi: mt76: mt7996: remove unused eeprom band selection 16a24667 wifi: mt76: mt7996: let non-bufferable MMPDUs use correct hw queue d39bb7c8 wifi: mt76: mt7996: remove mt7996_mcu_beacon_check_caps() 4046b591 wifi: mt76: mt7915: remove mt7915_mcu_beacon_check_caps() d63cb85c wifi: mt76: add missing locking to protect against concurrent rx/status calls 22f1b777 mt76: adjust for ieee80211_is_bufferable_mmpdu API change 8ecf551c wifi: mt76: set NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 on supported drivers efa44cb5 wifi: mt76: ignore key disable commands 56f0cd4d wifi: mt76: mt7915 add tc offloading support 021ded36 tools: Fix compile error with glibc Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: fix typoDavid Bauer2023-05-181-1/+1
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* bmips: improve kernel patchesÁlvaro Fernández Rojas2023-05-1714-185/+181
| | | | | | | Add missing patch headers and regenerate the ones that contain an obsolete patch header. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mdadm: fix compilation with musl 1.2.4Nick Hainke2023-05-161-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | _LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions. Fixes error in the form of: restripe.c: In function 'restore_stripes': restripe.c:758:43: error: 'off64_t' undeclared (first use in this function); did you mean 'off_t'? 758 | (off64_t)read_offset) { | ^~~~~~~ | off_t restripe.c:758:43: note: each undeclared identifier is reported only once for each function it appears in restripe.c:758:51: error: expected ')' before 'read_offset' 758 | (off64_t)read_offset) { | ^~~~~~~~~~~ | ) restripe.c:757:36: note: to match this '(' 757 | if (lseek64(source, read_offset, 0) != | ^ make[3]: *** [Makefile:193: restripe.o] Error 1 Fixes: fff878c5bcda ("toolchain/musl: update to 1.2.4") Signed-off-by: Nick Hainke <vincent@systemli.org>
* e2fsprogs: fix compilation with musl 1.2.4Tianling Shen2023-05-161-1/+5
| | | | | | | | | musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and autotools failed to check the lseek64 function. Force enable ac_cv_func_lseek64 to workaround it. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* f2fs-tools: fix compilation with musl 1.2.4Tianling Shen2023-05-161-1/+5
| | | | | | | | | musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and autotools failed to check the lseek64 function. Force enable ac_cv_func_lseek64 to workaround it. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ath79: add support for MikroTik RB951Ui-2HnDMichał Kępień2023-05-166-0/+168
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MikroTik RB951Ui-2HnD is a wireless SOHO router that was previously supported by the ar71xx target, see commit d19b868b12 ("ar71xx: Add support for MikroTik RB951Ui-2HnD"). Specifications -------------- - SoC: Atheros AR9344 (600 MHz) - RAM: 128 MB (2x 64 MB) - Storage: 128 MB NAND flash (various manufacturers) - Ethernet: Atheros AR8229 switch, 5x 10/100 Mbit/s - 1x PoE in (port 1, 8-30 V input) - 1x PoE out (port 5, 500 mA output) - Wireless: Atheros AR9340 (802.11b/g/n) - USB: 2.0 (1A) - 9x LED: - 1x power (green, not configurable) - 1x user (green) - 5x FE ports (green) - 1x wireless (green) - 1x PoE out (red) - 1x button (restart) See https://mikrotik.com/product/RB951Ui-2HnD for more details. Flashing -------- TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedures at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
* libbsd: fix compilation with musl 1.2.4Robert Marko2023-05-161-1/+3
| | | | | | | | | | | musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces so just having _GNU_SOURCE defined is not enough anymore. _LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions. Fixes: fff878c5bcda ("toolchain/musl: update to 1.2.4") Signed-off-by: Robert Marko <robimarko@gmail.com>
* linux-firmware: move firmware file for mt7601uDaniel Golle2023-05-151-3/+3
| | | | | | | | | | | | | | | The firmware file for mt7601u (MediaTek MT7601U Wireless MACs) has been moved to the mediatek/ folder by commit 8451c2b1 mt76xx: Move the old Mediatek WiFi firmware to mediatek Address this by updating the location of the firmware file in our linux-firmware Makefile generating the mt7601u-firmware package. All other MediaTek Wi-Fi firmware files are supplied by OpenWrt's own repository rather than being taken from linux-firmware. Fixes: d53fe5d9ce ("linux-firmware: update to 20230515") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* linux-firmware: update to 20230515Daniel Golle2023-05-152-2/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Package offloading firmware for MT7981 which has been added to linux-firmware recently and became available in this release. Changes since 20230515: 51290942 Merge branch 'main' of https://github.com/CirrusLogic/linux-firmware cc628d65 cirrus: Add firmware and tuning files for HP G10 series laptops 905d3265 linux-firmware: update firmware for mediatek bluetooth chip (MT7922) d1962891 WHENCE: Cleanup Realtek BT firmware provenance 6569484e linux-firmware: update firmware for MT7922 WiFi device 7d639e80 cnm: update chips&media wave521c firmware. b8a56bf2 cirrus: Add firmware and tuning files for Lenovo ThinkPad P1 Gen 6 6c9e0ed5 check_whence: error on directory listed as File 05183b7b check_whence: error on duplicate file entries c4423c91 WHENCE: comment out duplicate MediaTek firmware 2bc50f50 Merge branch 'mtl_guc_70.6.6' of git://anongit.freedesktop.org/drm/drm-firmware 192ee6d1 i915: Add GuC v70.6.6 for MTL 312c61f5 amdgpu: update DCN 3.1.6 DMCUB firmware 0061a2dd rtl_bt: Update RTL8852B BT USB firmware to 0xDBC6_B20F 1de22a39 rtl_bt: Update RTL8761B BT USB firmware to 0xDFC6_D922 dee0d4cd rtl_bt: Update RTL8761B BT UART firmware to 0x9DC6_D922 fab14965 Group all Conexant V4L devices together e88bdbe4 rtl_nic: update firmware of USB devices 6536a964 linux-firmware: Update firmware file for Intel Bluetooth AX200 2ca17876 linux-firmware: Update firmware file for Intel Bluetooth AX201 7610656f linux-firmware: Update firmware file for Intel Bluetooth AX203 209ba083 linux-firmware: Update firmware file for Intel Bluetooth AX203 a2739f05 linux-firmware: Update firmware file for Intel Bluetooth AX211 1ee587d5 linux-firmware: Update firmware file for Intel Bluetooth AX211 40ba7eee linux-firmware: Update firmware file for Intel Bluetooth AX210 bcbbf6bf linux-firmware: update firmware for MT7981 507ee862 Merge branch 'main' of github.com:sampathnimmmala/bt_firmware 2c6be1a4 qca: Update firmware files for BT chip WCN6750 8451c2b1 mt76xx: Move the old Mediatek WiFi firmware to mediatek 53e48f93 rtl_bt: Add firmware and config files for RTL8851B 69143e8e linux-firmware: Update AMD cpu microcode 1c942e46 Merge branch 'for-upstream' of https://github.com/CirrusLogic/linux-firmware 45530bcb linux-firmware: add firmware for MT7981 0d02ce69 linux-firmware: update firmware for MT7921 WiFi device 2deb2d30 linux-firmware: update firmware for mediatek bluetooth chip (MT7921) 9fdb844b linux-firmware: update qat firmware 74afc00d linux-firmware: Add firmware for Cirrus CS35L41 on Lenovo Laptops 86da2ac9 Merge https://github.com/pkshih/linux-firmware 5d0d24b3 linux-firmware: update firmware for MT7916 0aea9cdf Merge branch 'ath10k-20230405' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware 9f7502f1 rtw89: 8852b: update format-1 fw to v0.29.29.1 b9c8e9f7 rtw89: 8852c: update fw to v0.27.56.13 d1dc3048 ath11k: WCN6855 hw2.0: update board-2.bin 8115bd84 ath11k: WCN6750 hw1.0: update to WLAN.MSL.1.0.1-01160-QCAMSLSWPLZ-1 7d2ab030 ath11k: QCN9074 hw1.0: update to WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 b58b0869 ath11k: IPQ8074 hw2.0: update to WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 0747362d ath11k: IPQ8074 hw2.0: update board-2.bin 7262bd5d ath11k: IPQ6018 hw1.0: update to WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 aa98ffa3 ath11k: IPQ6018 hw1.0: update board-2.bin 2c67adc9 ath10k: QCA99X0 hw2.0: update board-2.bin a5dcb441 ath10k: QCA9984 hw1.0: update board-2.bin d0731d40 ath10k: QCA9888 hw2.0: update board-2.bin e13fedda ath10k: QCA6174 hw3.0: update board-2.bin 465dc284 ath10k: QCA4019 hw1.0: update board-2.bin 2e92a49f nvidia: update Tu10x and Tu11x signed firmware to support newer Turing HW 00258371 linux-firmware: update firmware for MT7922 WiFi device 33d8bf79 linux-firmware: update firmware for mediatek bluetooth chip (MT7922) 87bb6c9a Merge tag 'iwlwifi-fw-2023-03-30' of http://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware 956c1163 Merge branch 'mlimonci/update-dcn-3-1-4' of https://gitlab.freedesktop.org/superm1/linux-firmware 717e62eb linux-firmware: Amphion: Update vpu firmware 7bce2920 Merge https://github.com/pkshih/linux-firmware 78a8782a iwlwifi: add new FWs from core78-32 release a91d0e78 iwlwifi: update 9000-family firmwares to core78-32 9ee24ce0 amdgpu: Update SDMA 6.0.1 firmware 7df2a1ae amdgpu: Add PSP 13.0.11 firmware f098803d amdgpu: Update PSP 13.0.4 firmware 2cc9a4d0 amdgpu: Update GC 11.0.1 firmware eb13e669 amdgpu: Update DCN 3.1.4 firmware 898b7def amdgpu: Add GC 11.0.4 firmware e40a5b63 rtw88: 8822c: Update normal firmware to v9.9.15 bcdcfbcf linux-firmware: Update firmware file for Intel Bluetooth AX101 b422cdd6 linux-firmware: Update firmware file for Intel Bluetooth 9462 3e4c3b8d linux-firmware: Update firmware file for Intel Bluetooth 9462 6fcdb8e7 linux-firmware: Update firmware file for Intel Bluetooth 9560 46384d1c linux-firmware: Update firmware file for Intel Bluetooth 9560 1d797f86 linux-firmware: Update firmware file for Intel Bluetooth AX203 53c086b3 linux-firmware: Update firmware file for Intel Bluetooth AX203 9cc9745d linux-firmware: Update firmware file for Intel Bluetooth AX211 45319be8 linux-firmware: Update firmware file for Intel Bluetooth AX211 61d58194 linux-firmware: Update firmware file for Intel Bluetooth AX210 7f490a9a Merge branch 'dmc-adlp_2.19-mtl_2.12' of git://anongit.freedesktop.org/drm/drm-firmware dcac1477 Merge branch 'mtk-20230315' of https://github.com/tinghan-shen/linux_fw_scp 1f82dd25 linux-firmware: add firmware files for NXP BT chipsets 49ad74b3 Merge https://github.com/pkshih/linux-firmware 2c07f017 rtw89: 8852b: update format-1 fw to v0.29.29.0 b50cf920 rtw89: 8852b: add format-1 fw v0.29.26.0 416a66ca rtw89: 8852b: rollback firmware to v0.27.32.1 a18a444b i915: Update MTL DMC to v2.12 4ee236db i915: Update ADLP DMC to v2.19 d0997ff6 mediatek: Update mt8192/mt8195 SCP firmware to support MM21 and MT21 c761dbe8 Merge tag 'iwlwifi-fw-2023-03-13' of http://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware 5bc279fb iwlwifi: update core69 and core72 firmwares for So device Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* generic: mtk_eth_soc: don't crash if WO firmware is missingDaniel Golle2023-05-151-0/+28
| | | | | | | Import patch to prevent crashes in case WO firmware is missing on devices with only a single frontend (eg. MT7981+MT7976). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 22:32:33 +0000