aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* realtek: add ZyXEL GS1900-24HPv2 supportSoma Zambelly2021-09-134-1/+131
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24HPv2 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: W631GG8MB-12 128 MiB DDR3 SDRAM (stock firmware is configured to use only 64 MiB) * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 24 ethernet port link/activity LEDs (green, SoC controlled) 24 ethernet port PoE status LEDs 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: 1 "RESTORE" button on front panel 1 "RESET" button on front panel * Power 120-240V AC C13 * UART: 1 serial header (J41) with populated standard pin connector on the left edge of the PCB, angled towards the side. The casing has a rectangular cutout on the side that provides external access to these pins. Pinout (front to back): + GND + TX + RX + VCC Serial connection parameters for both devices: 115200 8N1. Installation ------------ OEM upgrade method: (Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged) * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
* sunxi: enable MUSB in A7 subtargetZhao Yu2021-09-131-0/+8
| | | | | | | like commit 78c1ed6. Without this,Some USB port on H3 baseboard can' work. So, need enable MUSB support on this target. Signed-off-by: Zhao Yu <574249312@qq.com>
* kernel: add package kmod-iio-ads1015 and remove kmod-hwmon-ads1015Christian Pointner2021-09-132-14/+15
| | | | | | | | | | | | The hwmon driver for the ADC ADS1015 has been removed in Linux 5.4 in favor of a driver in the iio system. For details see: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=2c9d5b5e This fixes: https://bugs.openwrt.org/index.php?do=details&task_id=4005 Run-tested: ramips/mt76x8 (Onion Omega 2+) Signed-off-by: Christian Pointner <equinox@spreadspace.org>
* kernel: backport switchdev fix for bridge in bridge configurationsFabian Bläse2021-09-131-0/+60
| | | | | | | | | | | | | | | | | | | This patch fixes the forwarding behavior of bridge in bridge configurations with DSA. Without it, the configuration of the upper bridge might overwrite settings of the lower bridge. For example, a vlan-aware bridge with DSA interfaces in it might be offloaded to the DSA hardware. If the bridge interface itself gets slave of a different bridge without vlan filtering, the vlan filtering setting of the lower bridge is overwritten by the upper bridge, which results in an incorrect hardware configuration. This was backported from kernel 5.7. Ref: https://lore.kernel.org/netdev/20191222192235.GK25745@shell.armlinux.org.uk/ Fixes: FS#3996 Signed-off-by: Fabian Bläse <fabian@blaese.de>
* kernel: bump 5.4 to 5.4.145John Audia2021-09-1311-72/+12
| | | | | | | | | | | | Removed upstreamed: generic-backport/040-ARM-8918-2-only-build-return_address-if-needed.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.4 to 5.4.144John Audia2021-09-1315-56/+56
| | | | | | | | | | | | | Manually rebased: backport-5.4/370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.64John Audia2021-09-1311-14/+14
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ipq806x/R7800 Run-tested: bcm2711/RPi4B, ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: fix jffs2 compilation with GCC_PLUGIN_RANDSTRUCT enabledMatt Merhar2021-09-132-2/+2
| | | | | | | | | Designated initializers are required when using the randstruct GCC plugin, otherwise an error like the following is seen: ./include/linux/lzma.h:60:31: error: positional initialization of field in 'struct' declared with 'designated_init' attribute [-Werror=designated-init] Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* kernel: Add missing kernel config optionsHauke Mehrtens2021-09-135-5/+6
| | | | | | | These options are selectable when some of the kernel debug options like KERNEL_SOFTLOCKUP_DETECTOR are selected. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* build: Replace KERNEL_LOCKUP_DETECTOR with KERNEL_SOFTLOCKUP_DETECTORHauke Mehrtens2021-09-131-16/+4
| | | | | | | | | | | | | The LOCKUP_DETECTOR configuration option split into the SOFTLOCKUP_DETECTOR and HARDLOCKUP_DETECTOR configuration option some time ago. The HARDLOCKUP_DETECTOR option is only working on some architectures, but SOFTLOCKUP_DETECTOR should work everywhere. Replace KERNEL_LOCKUP_DETECTOR with KERNEL_SOFTLOCKUP_DETECTOR. LOCKUP_DETECTOR will be selected by SOFTLOCKUP_DETECTOR automatically. Fixes: b951f53fbae3 ("build: Add additional kernel debug options") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq806x: switch to kernel 5.10Ansuel Smith2021-09-121-2/+1
| | | | | | | | | Move kernel version to 5.10 as has been tested by many users with positive feedback. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [Tested on: ipq8064/g10; ipq8065/nbg6817] Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq-wifi: Drop empty wifi package for Netgear WAC510Sven Eckelmann2021-09-121-2/+0
| | | | | | | | | | The ipq-wifi-netgear_wac510 package is not selected by any device and would be empty anyway. The default board-2.bin from ath10k-board-qca4019 is therefore used for this device and the package doesn't provide any visible features. Fixes: b126d9c3a3d3 ("ipq40xx: add netgear wac510 support") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Fix board-2.bin package name for Plasma Cloud PA2200Sven Eckelmann2021-09-121-1/+1
| | | | | | | | | | | The board data file for the Plasma Cloud PA2200 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device package name resulted in a not correctly selected package for the device specific board-2.bin. The wifi driver has therefore loaded the wrong calibration information into the wifi chip. Fixes: 4871fd2616ac ("ipq40xx: add support for Plasma Cloud PA2200") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Fix board-2.bin package name for Plasma Cloud PA1200Sven Eckelmann2021-09-121-1/+1
| | | | | | | | | | | The board data file for the Plasma Cloud PA1200 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device package name resulted in a not correctly selected package for the device specific board-2.bin. The wifi driver has therefore loaded the wrong calibration information into the wifi chip. Fixes: ea5bb6bbfee0 ("ipq40xx: add support for Plasma Cloud PA1200") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Select correct board-2.bin for EnGenius EMR3500Sven Eckelmann2021-09-121-0/+1
| | | | | | | | | The board data file for the EnGenius EMR3500 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong calibration information will be loaded into the wifi chip. Fixes: 3f61e5e1b97e ("ipq40xx: add support for EnGenius EMR3500") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Select correct board-2.bin for EnGenius EMD1Sven Eckelmann2021-09-121-0/+1
| | | | | | | | | The board data file for the EnGenius EMD1 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong calibration information will be loaded into the wifi chip. Fixes: 51f303597839 ("ipq40xx: add support for EnGenius EMD1") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* glibc: update to latest 2.33 HEAD (bug 28213)Hans Dedecker2021-09-121-2/+2
| | | | | | | | | | 9b01145592 MIPS: Setup errno for {f,l,}xstat 9c676ef514 RISC-V: Update rv64 ULPs c6cadbf83a linux: Remove shmmax check from tst-sysvshm-linux 22d37364ae librt: add test (bug 28213) 27a78fd712 librt: fix NULL pointer dereference (bug 28213) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: bump 5.10 to 5.10.63Rui Salvaterra2021-09-091-2/+2
| | | | | | No patches refreshed. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.62Rui Salvaterra2021-09-096-22/+22
| | | | | | Patches automatically refreshed. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* firmware-utils: tplink-safeloader: use revision fieldSander Vanheule2021-09-092-1/+3
| | | | | | | | | | | | | The structured soft-version partition has a field which contains a (source) revision number. Factory images used to include this, but it was accidentaly removed during an earlier refactoring. Include the source revision number again in the generated soft-version partition. Additionaly, also show this revision number when printing image info. Fixes: 1a211af2cb3b ("firmware-utils: tplink-safeloader: refactor meta-partition generation") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* mvebu: add support for iEi Puzzle-M901/Puzzle-M902Ian Chang2021-09-096-0/+868
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification ---------------------- * CN9130 SoC, Quad-core ARMv8 Cortex-72 @ 2200 MHz * 4 GB DDR * 4 GB eMMC * mmcblk0 - mmcblk0p1 64M kernel_1 - mmcblk0p2 64M kernel_2 - mmcblk0p3 512M rootfs_1 - mmcblk0p4 512M rootfs_2 - mmcblk0p5 512M Reserved - mmcblk0p6 64M Reserved - mmcblk0p7 1.8G rootfs_data * 4 MB (SPI Flash) * 6 x 2.5 Gigabit ports (Puzzle-M901) - External PHY with 6 ports (AQR112R) * 6 x 2.5 Gigabit ports (Puzzle-M902) - External PHY with 6 ports (AQR112R) 3 x 10 Gigabit ports (Puzzle-M902) - External PHY with 3 ports (AQR113R) * 4 x Front panel LED * 1 x USB 3.0 * Reset button on Rear panel * UART (115200 8N1,header on PCB) Flash instructions: The original firmware is based on OpenWrt. Flash firmware using LuCI and CLI Signed-off-by: Ian Chang <ianchang@ieiworld.com>
* mvebu: backport CN9130 dts necessary files changes to 5.4Ian Chang2021-09-0910-0/+2883
| | | | | | | | | 1. Add support for Marvell CN9130 SoC 2. Add support for CP115,and create an armada-cp11x.dtsi file which will be used to instantiate both CP110 and CP115 3. Add support for AP807/AP807-quad,AP807 is a major component of CN9130 SoC series 4. Drop PCIe I/O ranges from CP11x file and externalize PCIe macros from CP11x file Signed-off-by: Ian Chang <ianchang@ieiworld.com>
* iproute2: m_xt.so depends on dynsyms.listRoman Yeryomin2021-09-091-1/+2
| | | | | | | | | | | | | | | | | | When doing parallel build on a fast machine with bottleneck in i/o, m_xt.so may start linking faster than dynsyms.list gets populated, resulting in error: ld:dynsyms.list:0: syntax error in dynamic list Fix this by adding dynsyms.list as make dependency to m_xt.so Described also here: https://bugs.openwrt.org/index.php?do=details&task_id=3353 Change from v1: - add dynsysms.list dependancy only when shared libs are enabled Signed-off-by: Roman Yeryomin <roman@advem.lv> Fixes: FS#3353
* kernel: Set CONFIG_RCU_CPU_STALL_TIMEOUT=21Hauke Mehrtens2021-09-0916-16/+2
| | | | | | | | | | | | The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60 seconds to 21 seconds in 2012 in the upstream kernel. Some targets already use 21 seconds. This patch changes the default value in the generic configuration to 21 seconds and removes the target specific configuration options. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
* x86: switch to kernel 5.10Paul Spooren2021-09-081-2/+1
| | | | | | | Seems to be working fine in QEMU and the wild. Signed-off-by: Paul Spooren <mail@aparcar.org> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: switch to kernel 5.10Rui Salvaterra2021-09-081-2/+1
| | | | | | | | | | It's been brewing on my cortexa9 subtarget (Turris Omnia) for months. Perfectly stable. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> [modify subject to match previous updates] Signed-off-by: Paul Spooren <mail@aparcar.org>
* tools/libtool: update to 2.4.2Ivan Pavlov2021-09-079-48/+26
| | | | | | | Refresh patches. Remove upstreamed: 001-fix-func_append.patch Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
* bcm53xx: specify switch ports for more devicesRafał Miłecki2021-09-072-0/+864
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* linux: backport DSA b53 driver fixes for switch portsRafał Miłecki2021-09-072-0/+82
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: seama.h: replace LGPL-2.1-or-later boilerplate with SPDXRafał Miłecki2021-09-071-15/+1
| | | | | | | | | | | | | | | This was missed because scancode license scanner was confused by a slightly different than expected license text (96,75% license score). License text included "file" instead of "library" in the main part of the licensing info. It also used "The GNU C Library" instead of the standard "This library" in 2nd and 3rd paragraphs. The first paragraph clearly mentions LGPL-2.1-or-later and the use of "file" instead of "library" should not affect licensing. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mac80211: revert faulty change that was breaking broadcast txFelix Fietkau2021-09-061-13/+2
| | | | | Fixes: 0f6887972adc ("mac80211: add missing change for encap offload on devices with sw rate control") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/findutils: fix build on macosKevin Darbyshire-Bryant2021-09-061-0/+4
| | | | | | | | Use same fix as homebrew: https://github.com/Homebrew/homebrew-core/pull/69761 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: add support for Sitecom WLR-4100 v1 002Andrea Poletti2021-09-054-2/+214
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router Specification: SoC: MT7620A RAM: 64 MB DDR2 Flash: MX25L6405D SPI NOR 8 MB WIFI: 2.4 GHz integrated Ethernet: 5x 10/100/1000 Mbps QCA8337 USB: 1x 2.0 LEDS: 2x GPIO controlled, 5x switch Buttons: 1x GPIO controlled UART: row of 4 unpopulated holes near USB port, starting count from white triangle on PCB: VCC 3.3V GND TX RX baud: 115200, parity: none, flow control: none Installation Connect to one of LAN (yellow) ethernet ports, Open router configuration interface, Go to Toolbox > Firmware, Browse for OpenWrt factory image with dlf extension and hit Apply, Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Known issues Some USB 2.0 devices work at full speed mode 1.1 only MAC addresses factory partition only contains one (binary) MAC address in 0x4. u-boot-env contains four (ascii) MAC addresses, of which two appear to be valid. factory 0x4 **:**:**:**:b9:84 binary u-boot-env ethaddr **:**:**:**:b9:84 ascii u-boot-env wanaddr **:**:**:**:b9:85 ascii u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii The factory firmware only assigns ethaddr. Thus, we take the binary value which we can use directly in DTS. Additional information OEM firmware shell password is: SitecomSenao useful for creating backup of original firmware. There is also another revision of this device (v1 001), based on RT3352 SoC Signed-off-by: Andrea Poletti <polex73@yahoo.it> [remove config DT label, convert to nvmem, remove MAC address setup from u-boot-env, add MAC address info to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WA1201 v2Robert Balas2021-09-056-3/+221
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is a wireless access point working on the 2.4 GHz and 5 GHz band, based on Qualcomm/Atheros QCA9563 + QCA9886. Specification - 775 MHz CPU - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - QCA9563: 2.4 GHz 3x3 - QCA9886: 5 GHz - AR8033: 1x 1 Gbs Ethernet - 4x LED, WPS factory reset and power button - bare UART on PCB (accessible through testpoints) Methods for Flashing: - Apply factory image in OEM firmware web-gui. Wait a minute after the progress bar completes and restart the device. - Sysupgrade on top of existing OpenWRT image - Solder wires onto UART testpoints and attach a terminal. Boot the device and press enter to enter u-boot's menu. Then issue the following commands 1. setenv serverip your-server-ip setenv ipaddr your-device-ip 2. tftp 0x80060000 openwrt-squashfs.bin (Rembember output of size in hex, henceforth "sizeinhex") 3. erase 0x9f030000 +"sizeinhex" 4. cp.b 0x80060000 0x9f030000 0x"sizeinhex" 5. reboot Recover: - U-boot serial console Signed-off-by: Robert Balas <balasr@iis.ee.ethz.ch> [convert to nvmem] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/libressl: update to 3.3.4Rosen Penev2021-09-051-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/cmake: update to 3.21.2Rosen Penev2021-09-053-4/+4
| | | | | | Refreshed patches. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/bison: update to 3.7.6Rosen Penev2021-09-051-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/dosfstools: update to 4.2Rosen Penev2021-09-052-29/+2
| | | | | | Remove upstream backport. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/findutils: update to 4.8.0Rosen Penev2021-09-051-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/tar: update to 1.34Rosen Penev2021-09-052-3/+3
| | | | | | Refresh patch. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/zstd: update to 1.5.0Rosen Penev2021-09-051-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* busybox: update to version 1.34.0Hannu Nyman2021-09-0417-203/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Update busybox to version 1.34.0 * Remove upstreamed patches (205, 530, 540) * Remove one old patch that does not apply any more. (203) That was originally introduced in 2008 with 563d23459, but does not apply after busybox restructuring with https://git.busybox.net/busybox/commit/networking/udhcp/dhcpc.c?h=1_34_stable&id=e6007c4911c3ea26925f9473b9f156a692585f30 and https://git.busybox.net/busybox/commit/networking/udhcp/dhcpc.c?h=1_34_stable&id=1c7253726fcbab09917f143f0b703efbd2df55c3 * Refresh config and patches. * Backport upstream fixes for - MIPS compilation breakage and - process substitution regression Config refresh: Refresh commands, run after busybox is first built once: cd utils/busybox/ cd config/ ../convert_menuconfig.pl ../../../../build_dir/target-aarch64_cortex-a53_musl/busybox-default/busybox-1.34.0 cd .. ./convert_defaults.pl < ../../../build_dir/target-aarch64_cortex-a53_musl/busybox-default/busybox-1.34.0/.config > Config-defaults.in Manual edits needed afterward: * Config-defaults.in: OpenWrt config symbol IPV6 logic applied to BUSYBOX_DEFAULT_FEATURE_IPV6 * Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec) * Config-defaults.in: OpenWrt logic applied to BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917) BUSYBOX_DEFAULT_UDHCPC_DEFAULT_INTERFACE (just "") * config/editors/Config.in: Add USE_GLIBC dependency to BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090) * config/shell/Config.in : change at "Options common to all shells" the symbol SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH (discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html Apparently our script does not see the hidden option while prepending config options with "BUSYBOX_CONFIG_" which leads to a missed dependency when the options are later evaluated.) * Edit Config.in files by adding quotes to sourced items in config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f) Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* mediatek: add support for TOTOLINK A8000RUChuanhong Guo2021-09-033-0/+345
| | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7622 - RAM: 512MB - Flash: MX35LF1GE4AB 128MB SPI NAND - Ethernet: RTL8367S 5x1GbE - WiFi: 2.4G: MT7622 5G: MT7615N x2 - Other ports: USB3.0 x1 Flash instruction: *important*: upgrade vendor firmware to at least V7.1cu.643_B20200521 1. hold the reset button and power on the device. wait for about 10s before releasing the reset button. 2. upload sysupgrade.bin via u-boot recovery page on http://192.168.1.1 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ucode: update to latest Git HEADJo-Philipp Wich2021-09-011-9/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 929c862 vm: fix toplevel function call protocol 8f34d70 fs: fix chown() and rename() error return values 03ca445 tests: disable fuzz tests for now 3b1be3d types: mark further GC roots d49af4e types: fix comparison of differently signed integers c79ff39 types: handle conversion errors when dealing with negative error indexes 3315b1f types: allow negative array indexes d5b25f9 treewide: harmonize function naming cc4ce8d module: remove unused defines f5d7526 examples: add libucode usage examples 559eff2 types, vm: adjust GC api e5e7e62 treewide: move header files into dedicated directory ff6168a build: install header files 7e6ce0f main: introduce new flag `-x` to allow disabling specific functions b1817b3 vm: fix invalid memory access on GC'ing uninitialized VM context 498fe87 main: refactor option parsing and VM setup ff52440 treewide: consolidate typedef naming 1d60418 vm: add API to control trace mode 48f33ad vm: make root exception handler configurable 0f69f09 vm: fix invalid memory access on toplevel function calls 6bcc318 vm: fix handling exceptions in top-level function calls 4ae0568 lib, vm: reimplement exit() as exception type 2f77657 vm: extend API to allow returning result value from VM execution 111645a vm: remove module preloading logic 38ff6de main: preload modules ourselves d5bc223 vm: add uc_vm_invoke() helper ef0baf1 vm: cosmetic fix for outputting exceptions without source context b11a2fa vm: move global scope allocation into uc_vm_init() 900b2a3 vm: add getter and setter for vm globals scope 0179576 lib: rename uc_add_proto_functions() to uc_add_functions() 98b9c84 lib: expose stdlib function array 1adfba0 treewide: eliminate dead code and unused functions 3974e71 treewide: replace a number of unnecessary type casts bf85226 treewide: move ressource type registry into vm instance e2b3d2e build: split into libucode and ucode cli dad8f3a types: properly deal with circular data in GC mark phase 62dbd64 lexer: rename UT_ prefixed constants to UC_ bc8e465 types: fix wrong assert() on tearing down object trees 853b9f1 vm: fix potential invalid memory access in uc_vm_get_error_context() 6f05cdd lib: fix refcount imbalance in uc_require_path() 96f140b lib, vm: ensure that require() compiles modules only once df5db5f compiler: don't segfault on invalid declaration expressions a97c7a1 lexer: transition into EOF state on unrecognized character 2a838d1 compiler: improve mapping of binary operator tokens to instructions 9872f65 vm: add support for I_LE and I_GE instructions 4e410c3 treewide: let uc_cmp() use instruction instead of token numbers ce6081d lexer, vm: reorder token and instruction numbers 234a4f6 lib: implement b64enc() and b64dec() functions 856a0c0 lib: only consider context of calling function for callbacks 86fb130 lib: implement min() and max() functions 3e893e6 lib: pass-through "this" context to library function callbacks 42de7ab lib: implement `sourcepath()` function 05c80a7 lib: fix negative uc_index() return value on 32bit systems 9874562 lexer: implement raw code mode 3b665c8 lexer: drop value union from keyword table 44354cf lexer, compiler: separate TK_BOOL token into TK_TRUE and TK_FALSE tokens 5879bdf syntax: drop Infinity and NaN keywords d4edadc lib: rename uc_lib_init() to uc_load_stdlib() d81bad7 main, lib: move allocation of globals object into lib function c4f4b38 main: simplify REQUIRE_SEARCH_PATH initialization 54ca3aa types: fix uninitialized memory on setting non-contiguous array indexes cbc0d78 build: let require search patch default to CMAKE_INSTALL_PREFIX 5714705 syntax: introduce `const` support ed32c42 compiler, lexer: add NO_LEGACY define to disable legacy syntax features ff6811f syntax: implement `delete` as proper operator 5803d86 lib: implement wildcard() function dfb7379 fs: implement chmod(), chown(), rename() and glob() functions 1ddf5b6 lexer: skip interpreter line in any source buffer 9951a00 build: lower minimum required CMake version to v3.13 7b81ab2 main: expose argv as global ARGV array to ucode scripts 7283a70 tests: rename misnamed testcases for consistency 3f80116 compiler: fix local for-loop initializer variable declarations f20b56f compiler: properly parse slashes in parenthesized division expressions 5c4e1ea lib: implement regexp(), a function to construct regexp instances at runtime e546bba lib: implement render(), an include variant capturing output in a string 0cb10c6 vm: implement mechanism to change output file descriptor eb8a64d lib: fix uc_sort() f1ffc9f vm: truncate long values after 60 chars in trace output 850612f compiler: properly handle break/continue in nested scopes f0a9875 compiler: properly handle keyword in parenthesized property access expression 1660433 compiler: fix stack mismatch on compiling `use strict` statements a36e0df syntax: implement support for 'use strict' pragma 827a34a vm, compiler: get rid of unused struct members 594cdf3 lib: implement assert() c4d1648 lib: add support for pretty printing JSON to printf() and sprintf() f2eaea3 lib: gracefully handle truncated format strings in uc_printf_common() 02629b8 lexer: fix infinite loop on parsing unterminated comments 2bc9bac lexer: fix infinite loop on parsing unterminated expression blocks f73e201 lexer: fix infinite loop when parsing regexp literal at EOF 86b4863 compiler: fix segfault on parsing invalid pre/post increment expressions 0e24509 lib: fix reporting source context lines at EOF e66b2ad compiler, lexer: improve lexical state handling e29b574 lib: fix uc_split() quirks 64eec7f treewide: ISO C / pedantic compliance 4af803d build: output error messages on test failures 9ef693e vm: improve context for early errors 6def9fc tests: pass ucode library path through environment d5dd183 treewide: address various sign-compare warnings 28825ac types: support creating ressource values without associated type 9c5106a types: fix potential memory leaks and null pointer accesses c51934a types: fix potential leak of key in ucv_object_add() 7b28727 main: fix ineffective EOF check in parse() 4cf897c lib: uc_system(): fix invalid free() of non-heap memory 35af4ba treewide: rework internal data type system f2c4b79 treewide: fix issues reported by clang code analyzer 93ededb tests: allow executing run_tests.sh from any directory 0e4a387 Add initial GitLab and GitHub CI support df73b25 tests: add more tests 41d33d0 tests: custom: return exit code if tests fails 1c548a6 cmake: do not output binaries into lib directory 2b59097 tests: create custom tests from current tests cases 8039361 main: provide just binary name in help output 778e4f7 lexer: fix incomplete struct initializers 502ecdc cmake: enable extra compiler checks 3c2aeff cmake: fix includes and libraries 617a114 cmake: make 3.0 minimum version f360350 lib: implement sleep(ms) function 7f0ff91 lib: allow parsing non-array, non-object value in json() Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* firewall4: update to latest Git HEADJo-Philipp Wich2021-09-011-3/+3
| | | | | | | cf835ce treewide: convert deprecated syntax c9a3bf5 tests: adapt to latest ucode Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: add missing CONFIG_SECURITY_NETWORK_XFRM ksymRui Salvaterra2021-08-312-0/+2
| | | | | | | | | Paul noticed a build failure [1] due to this missing symbol. Add it as disabled to both generic kconfigs. [1] https://github.com/aparcar/openwrt/runs/3480872706?check_suite_focus=true#step:11:63 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ethtool: fix recursive dependencyEneas U de Queiroz2021-08-311-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change the CONFLICTS definition from the alternative package (ethtool-full) to the main one. The CONFLICTS line creates a dependency to the conflicting package. Right now, the dependency would be created in the PACKAGE_ethtool-full symbol: config PACKAGE_ethtool-full depends on m || (PACKAGE_ethtool != y) When the main package is selected by airmon-ng, it selects PACKAGE_ethtool, *depending* on the value of PACKAGE_ethtool-full: config PACKAGE_airmon-ng select PACKAGE_ethtool if PACKAGE_ethtool-full<PACKAGE_airmon-ng In the first block, the value of PACKAGE_ethtool-full depends on the value of PACKAGE_ethtool. In the second block, the opposite is true: the value of PACKAGE_ethtool depends on the value of PACKAGE_ethtool-full. This is a recursive dependency. Fix it by changing the package where the dependency is created, so that only the value of PACKAGE_ethtool will depend on PACKAGE_ethtool-full. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* procd: fix issue mounting overlay fsDaniel Golle2021-08-311-2/+2
| | | | | | | | | | | | The previous procd update broke mounting overlayfs in an attempt to fix an off-by-one error. Revert that broken fix and apply fix from Nick Hainke <vincent@systemli.org> instead to bring things back to life. 20adf53 Revert "initd: fix off-by-one error in mkdev.c" 773e8da initd: fix off-by-one error in mkdev.c Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* firmware-utils: mkmerakifw-old: Add le32 supportMatthew Hagan2021-08-311-22/+41
| | | | | | | | | | | | | mkmerakifw-old was created for the z1 which uses the AR9344 SoC with be32 addressing. The MX64/MX65 devices use the same header style, however these boards use a BCM NSP SoC with le32 addressing. Since we may be booting initramfs images with this header, which may be of any size, within reason, board->imagelen is set to 0. The kernel image shoule be limited in the image Makefile. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: switch to the kernel 5.10Rafał Miłecki2021-08-311-1/+1
| | | | | | With PCI and USB regressions fixed it should be safe to switch now. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 21:49:00 +0000