aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* qoriq: use FIT uImage for Firebox M300 kernelStijn Tintel2022-06-141-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This requires U-Boot environment changes: setenv OpenWrt_kernel watchguard_firebox-m300-fit-uImage.itb setenv loadaddr 0x20000000 setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; mmc dev 0; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr' Trying to sysupgrade an image containing this change on an M300 already running OpenWrt will fail with the following error: Tue Jun 14 12:06:21 EEST 2022 upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n). Tue Jun 14 12:06:21 EEST 2022 upgrade: Kernel switched to FIT uImage. Update U-Boot environment. Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from bootdisk... Tue Jun 14 12:06:21 EEST 2022 upgrade: Extract boot sector from the image Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from image... Image check failed. This is to prevent rendering your device unbootable. Make the U-Boot environment changes as instruced above, and then flash the image using sysupgrade -F. The config can be kept, there is no need to use -n. After the new image booted successfully, you can increase the compat_version: uci set system.@system[0].compat_version='1.1' uci commit Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* qoriq: use KERNEL_SUFFIX in Build/sdcard-imgStijn Tintel2022-06-141-1/+1
| | | | | | | | | Use the KERNEL_SUFFIX variable in Build/sdcard-img, rather than using hardcoded "-kernel.bin", to allow overriding KERNEL_SUFFIX for a device. Fixes: 080a769b4da8 ("qoriq: new target") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* tools/ninja: update to 1.11.0Rosen Penev2022-06-132-1070/+3081
| | | | | | Updated patchset to latest. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for MTS WG430223Mikhail Zhilkin2022-06-136-2/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan WG443223). Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 128 MiB Flash: 128 MiB (Winbond W29N01HV) Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: No Button: 1 (Reset/WPS) LEDs: 2 (Red, Green) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WG430223 Installation ------------ 1. Login to the router web interface (superadmin:serial number) 2. Navigate to Administration -> Miscellaneous -> Access control lists & enable telnet & enable "Remote control from any IP address" 3. Connect to the router using telnet (default admin:admin) 4. Place *factory.trx on any web server (192.168.1.2 in this example) 5. Connect to the router using telnet shell (no password required) 6. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 7. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 8. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 9. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | A4:xx:xx:51:xx:F4 | No MACs was | | LAN | A4:xx:xx:51:xx:F6 | found on Flash | | WAN | A4:xx:xx:51:xx:F4 | [1] | | WLAN_2g | A4:xx:xx:51:xx:F5 | | | WLAN_5g | A6:xx:xx:21:xx:F5 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several MTS WG430223 devices even within the same broadcast domain. Stock firmware image format --------------------------- The same as Beeline Smartbox Flash but with another trx magic +--------------+---------------+----------------------------------------+ | Offset | | Description | +==============+===============+========================================+ | 0x0 | 31 52 48 53 | TRX magic "1RHS" | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: create new dtsi for Arcadyan routersMikhail Zhilkin2022-06-132-186/+199
| | | | | | | | | | | | | | | | | | | This commit moves common properties for the boards below to a new dtsi: Beeline Smartbox Flash (Arcadyan WG443223) MTS WG430223 (Arcadyan WG430223) The boards are almost the same. Here is the differences: +------+----------+----------+ | | WG430223 | WG443223 | +------+----------+----------+ | RAM | 128 | 256 | +------+----------+----------+ | USB | - | 1x3.0 | +------+----------+----------+ | LEDS | RG | RGB | +------+----------+----------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: allow custom trx magic for ArcadyanMikhail Zhilkin2022-06-131-3/+4
| | | | | | | | | | | | This commit: 1. Renames beeline-trx recipe in mt7621.mk to arcadyan-trx. The recipe is necessary for: - MTS WG430223 (Arcadyan WG430223) - Beeline Smartbox Flash (Arcadyan WG443223) 2. Allows specify custom trx magic which is different for the routers mentined above. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: decrease SPI frequency for Phicomm K2PAviana Cruz2022-06-131-2/+1
| | | | | | | | | | Some K2P comes with the worse boards with GD25Q128 (may be A2), which only works with 50MHz frequency and less. Reduce spi frequency so that these routers can boot. remove m25p,fast-read because it isn't needed for 50MHz SPI. Signed-off-by: Aviana Cruz <gwencroft@proton.me> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* hostapd: fix feature detectionRobert Marko2022-06-121-1/+1
| | | | | | | | | | | Fix hostapd feature detection after the bump to 2022-05-08. getopt was not updated correctly after upstream added support for -q arg. This reenables feature detection so that LuCi can check for features like SAE, fast roaming etc. Fixes: c35ff1affe8f ("hostapd: update to 2022-05-08") Signed-off-by: Robert Marko <robimarko@gmail.com>
* ath79: move ubnt-xm to tinyNick Hainke2022-06-1111-265/+281
| | | | | | | | | | | | | ath79 has was bumped to 5.10. With this, as with every kernel change, the kernel has become larger. However, although the kernel gets bigger, there are still enough flash resources. But the RAM reaches its capacity limits. The tiny image comes with fewer kernel flags enabled and fewer daemons. Improves: 15aa53d7ee65 ("ath79: switch to Kernel 5.10") Tested-by: Robert Foss <me@robertfoss.se> Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: add Ubiquiti UniFi 6 LR v2 targetsHenrik Riomar2022-06-114-0/+239
| | | | | | | | | | | | | | | Add targets: * Ubiquiti UniFi 6 LR v2 * Ubiquiti UniFi 6 LR v2 (U-Boot mod) This target does not have a RGB led bar like v1 did Used target/linux/ramips/dts/mt7621_ubnt_unifi.dtsi as inspiration The white dome LED is default-on, blue will turn on when the system is in running state Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
* mediatek: new target ubnt_unifi-6-lr-v1-ubootmodHenrik Riomar2022-06-112-5/+6
| | | | | | | | based on current ubnt_unifi-6-lr-ubootmod Signed-off-by: Daniel Golle <daniel@makrotopia.org> [added SUPPORTED_DEVICES for compatibility with existing setups] Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
* mediatek: new target mt7622-ubnt-unifi-6-lr-v1Henrik Riomar2022-06-115-31/+35
| | | | | | | | | | | | Based on current mt7622-ubnt-unifi-6-lr, this is a preparation for adding a v2 version of this target * v1 - with led-bar * v2 - two simple GPIO connected LEDs (in later commits) Signed-off-by: Daniel Golle <daniel@makrotopia.org> [added SUPPORTED_DEVICES for compatibility with existing setups] Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
* wireless-regdb: bump to 2022.06.06Stijn Tintel2022-06-112-3/+3
| | | | | | | | | | | | | | | | | 902b321 wireless-regdb: Update regulatory rules for Israel (IL) 20f6f34 wireless-regdb: add missing spaces for US S1G rules 25652b6 wireless-regdb: Update regulatory rules for Australia (AU) 081873f wireless-regdb: update regulatory database based on preceding changes 166fbdd wireless-regdb: add db files missing from previous commit e3f03f9 Regulatory update for 6 GHz operation in Canada (CA) 888da5f Regulatory update for 6 GHz operation in United States (US) 647bcaa Regulatory update for 6 GHz operation in FI c6b079d wireless-regdb: update regulatory rules for Bulgaria (BG) on 6GHz 2ed39be wireless-regdb: Remove AUTO-BW from 6 GHz rules 7a6ad1a wireless-regdb: Unify 6 GHz rules for EU contries 68a8f2f wireless-regdb: update regulatory database based on preceding changes Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* iw: bump to 5.19Stijn Tintel2022-06-113-45/+462
| | | | | | | | | | | | | | | | | | | | | | | 7e06706 iw: event: report missing radar events 5909e73 iw: survey: add support for radio stats 64bf570 update nl80211.h 0900996 iw: print Radar background capability if supported 56c6077 iw: print out assoc comeback event a4e5418 iw: support 160MHz frequency command for 6GHz band 5a71b72 iw: Print local EHT capabilities e3287a1 station: print EHT rate information ff67fb2 iw: fix double tab in mesh path header 05a5267 iw: fix 'upto' -> 'up to' 00a2985 iw: handle VHT extended NSS 82e0bd1 update nl80211.h c95877c info: add missing extended features 0976378 info: refactor extended features 79f20cb bump version to 5.19 Sync nl80211.h with our version of mac80211 and remove parts of the iw code that are not supported by our version of mac80211. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ath79: D-Link DAP-2680: select QCA9984 firmwareStijn Segers2022-06-111-1/+1
| | | | | | | | | | | | The DAP-2680 has a QCA9984 radio [1], but the commit adding support mistakenly adds the QCA99x0 firmware package. See forum topic [2]. [1] https://wikidevi.wi-cat.ru/D-Link_DAP-2680_rev_A1 [2] https://forum.openwrt.org/t/missing-5ghz-radio-on-dlink-dap-2680/ Fixes: 5b58710fad21 ("ath79: add support for D-Link DAP-2680 A1") Signed-off-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Alessandro Fellin <af.registrazioni@gmail.com>
* mac80211: sync nl80211.h with upstreamDavid Bauer2022-06-111-0/+22
| | | | | | | | | | | | Sync nl80211.h with upstream in order to maintain parity with nl80211_copy.h shipped with hostapd. This is necessary, as currently the enum value for NL80211_EXT_FEATURE_RADAR_BACKGROUND mismatches between hostapd and mac80211. This breaks background radar capability detection in hostapd. Reported-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David Bauer <mail@david-bauer.net>
* octeon: add SUPPORTED_DEVICES to er/erlitePaul Spooren2022-06-091-0/+2
| | | | | | | | | | | | | | | | Using the BOARD_NAME variable results for both er and erlite devices to identify themselfs as `er` and `erlite` (via `ubus call system board`). This is problematic when devices search for firmware upgrades since the OpenWrt profile is actually called `ubnt_edgerouter` and `ubnt_edgerouter-lite`. By adding the `SUPPORTED_DEVICE` a mapping is created to point devices called `er` or `erlite` to the corresponding profile. FIXES: https://github.com/openwrt/asu/issues/348 Signed-off-by: Paul Spooren <mail@aparcar.org>
* prereq-build: add additional git detectionChristian 'Ansuel' Marangi2022-06-091-1/+2
| | | | | | | | | | | | | | With some OS (Guix) the git submodule command is wrapped in a script. Current logic parse the git submodule script directly. If it's wrapped the prereq check wrongly fails while 'git submodule --recursive' is actually available. Add an additional check that try to directly use the 'git submodule' command to check if the prereq is satisfied. Fixes: #9986 Reported-by: Attila Lendvai <attila@lendvai.name> Suggested-by: Attila Lendvai <attila@lendvai.name> Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
* wolfssl: make WOLFSSL_HAS_OPENVPN default to yEneas U de Queiroz2022-06-091-1/+1
| | | | | | | | | | | | | Openvpn forces CONFIG_WOLFSSL_HAS_OPENVPN=y. When the phase1 bots build the now non-shared package, openvpn will not be selected, and WolfSSL will be built without it. Then phase2 bots have CONFIG_ALL=y, which will select openvpn and force CONFIG_WOLFSSL_HAS_OPENVPN=y. This changes the version hash, causing dependency failures, as shared packages expect the phase2 hash. Fixes: #9738 Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* Revert "wolfssl: set nonshared flag global"Christian 'Ansuel' Marangi2022-06-091-9/+1
| | | | | | | This reverts commit e0cc5b9b3ae65113f0e0dd9249dae4776b65c503. A better and correct solution was found. Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
* wolfssl: set nonshared flag globalChristian 'Ansuel' Marangi2022-06-091-1/+9
| | | | | | | | | | | | | | | | libwolfssl-benchmark should NOT be compiled as nonshared but currently there is a bug where, on buildbot stage2, the package is recompiled to build libwolfssl-benchmark and the dependency change to the new libwolfssl version. Each dependant package will now depend on the new wolfssl package instead of the one previously on stage1 that has a different package HASH. Set the nonshared PKGFLAGS global while this gets investigated and eventually fixed. Fixes: 0a2edc2714dc ("wolfssl: enable CPU crypto instructions") Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
* hostapd: fix missing HS20 support for hostapd-fullDavid Bauer2022-06-081-1/+1
| | | | | | | | | | | | | | | commit c3a4cddaaf45 ("hostapd: remove hostapd-hs20 variant") as well as commit 9f1927173ac6 ("hostapd: wpas: add missing config symbols") indicate hostapd-full should support Hotspot 2.0 already, but only wpa_supplicant (and wpad) do. How this happened is not really clear, as no commit adding support for Hotspot 2.0 is in the history. Fix this and add Hotspot 2.0 capability to hostapd-full. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: ubus: add bss-color to get_statusDavid Bauer2022-06-081-0/+6
| | | | | | | | Add the current BSS color to hostapd get_status method. This field is set to -1 in case BSS color is not active for the BSS. Signed-off-by: David Bauer <mail@david-bauer.net> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* hostapd: randomize default BSS colorDavid Bauer2022-06-083-2/+28
| | | | | | | In case no specific BSS color is configured, set it to a random value. Signed-off-by: David Bauer <mail@david-bauer.net> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* hostapd: update to 2022-05-08David Bauer2022-06-088-86/+94
| | | | | | | | | | Update hostapd to Git HEAD from 2022-05-08. This allows us to take advantage of background radar-detection as well as BSS color collision detection. Suggested-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David Bauer <mail@david-bauer.net> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* hostapd: Radius based VLANs on AP with PSKBernd Naumann2022-06-081-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch allows the user to set `auth_server` and related settings on non WPA2 Enterprise AP modes in `/etc/config/wireless`, too, so the Radius Attributes for Dynamic VLAN Assignment can be fetched from Radius. Without this patch, `auth_server` and other needed options are only written to `hostapd-phy<n>.conf` when `option encryption wpa2` is set. `hostapd` however supports "Station MAC address -based authentication" for non WPA Enterprise Modes, too. A classic approch is to use `accept_mac_file` which contains MAC addr and VLAN-ID pairs. But, using `accept_mac_file` does not support VLAN assignment for unknown stations. This is a sample `freeradius3` config, where a known station ("7e:a6:a7:2a:93:d2") is assigned to VLAN `65` and unknown stations are assigned to VLAN `67`. ``` "7ea6a72a93d2" Cleartext-Password := "7ea6a72a93d2" Tunnel-Type = "VLAN", Tunnel-Medium-Type = "IEEE-802", Tunnel-Private-Group-Id = 65 DEFAULT Cleartext-Password := "%{User-Name}" Tunnel-Type = "VLAN", Tunnel-Medium-Type = "IEEE-802", Tunnel-Private-Group-Id = 67 ``` Other option is to configure known stations via `accept_mac_file` and using only Radius for unknown stations. I tested this patch only with `wpa_key_mgmt=WPA-PSK`, and assumed that it should work with other Encryption/Access Mode, too. Signed-off-by: Bernd Naumann <bernd.naumann@kr217.de>
* realtek: add gpio-restart for D-Link DGS-1210-28Luiz Angelo Daros de Luca2022-06-071-0/+6
| | | | | | | | A GPIO assert is required to reset the system. Otherwise, the system will hang on reboot. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* realtek: add reset button for D-Link DGS-1210-28Luiz Angelo Daros de Luca2022-06-071-0/+18
| | | | | | | Tested in a DGS-1210-28 F3, both triggering failsafe and reboot. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* bcm53xx: remove BROKEN flag from Asus RT-AC88UArınç ÜNAL2022-06-071-1/+0
| | | | | | | The image builds and works fine on Asus RT-AC88U. Therefore, remove the BROKEN flag from the makefile. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* wolfssl: enable CPU crypto instructionsEneas U de Queiroz2022-06-072-0/+23
| | | | | | | | | | | | | | | | | | This enables AES & SHA CPU instructions for compatible armv8, and x86_64 architectures. Add this to the hardware acceleration choice, since they can't be enabled at the same time. The package was marked non-shared, since the arm CPUs may or may not have crypto extensions enabled based on licensing; bcm27xx does not enable them. There is no run-time detection of this for arm. NOTE: Should this be backported to a release branch, it must be done shortly before a new minor release, because the change to nonshared will remove libwolfssl from the shared packages, but the nonshared are only built in a subsequent release! Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* wolfssl: add benchmark utilityEneas U de Queiroz2022-06-071-3/+23
| | | | | | This packages the wolfssl benchmark utility. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* wolfssl: don't change ABI because of hw cryptoEneas U de Queiroz2022-06-071-10/+21
| | | | | | | | Enabling different hardware crypto acceleration should not change the library ABI. Add them to PKG_CONFIG_DEPENDS after the ABI version hash has been computed. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* kernel: bump 5.15 to 5.15.45Rui Salvaterra2022-06-0610-11/+11
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.15 to 5.15.44Rui Salvaterra2022-06-067-10/+9
| | | | | | | | Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in. Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.15 to 5.15.43Rui Salvaterra2022-06-061-2/+2
| | | | | | No patches needed rebasing. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.15 to 5.15.42Rui Salvaterra2022-06-0617-314/+38
| | | | | | | | | | | | | | | | | | | | Deleted (upstreamed): generic/backport-5.15/610-v5.18-netfilter-flowtable-move-dst_check-to-packet-path.patch [1] generic/pending-5.15/704-00-netfilter-flowtable-fix-excessive-hw-offload-attempt.patch [2] generic/pending-5.15/704-01-netfilter-nft_flow_offload-skip-dst-neigh-lookup-for.patch [3] generic/pending-5.15/704-02-net-fix-dev_fill_forward_path-with-pppoe-bridge.patch [4] generic/pending-5.15/704-03-netfilter-nft_flow_offload-fix-offload-with-pppoe-vl.patch [5] Manually rebased: generic/hack-5.15/650-netfilter-add-xt_FLOWOFFLOAD-target.patch [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.42&id=88b937673b3552d54da20f648e61a123f4c1fa67 [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.42&id=5f4197a020c049a59ea7907c31f9ab037dcefefe [3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.42&id=7613dcaceee281973145588f4244f2f78ef85b7f [4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.42&id=f96b2e06721249ebf8da3254cfef29dcb6583948 [5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.42&id=b329889974aed47e1167c85653c07097013e01a7 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.15 to 5.15.41Rui Salvaterra2022-06-0658-310/+248
| | | | | | | | | | | Deleted (upstreamed): generic/backport-5.15/890-v5.19-net-sfp-Add-tx-fault-workaround-for-Huawei-MA5671A-SFP-ON.patch [1] Other patches automatically rebased. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.41&id=99858114a3b2c8f5f8707d9bbd46c50f547c87c0 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.120John Audia2022-06-069-12/+12
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800, x86/64 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.119John Audia2022-06-068-53/+9
| | | | | | | | | | Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in. Patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800, x86/64 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.118John Audia2022-06-0610-131/+15
| | | | | | | | | | | | | Removed upstreamed: generic-backport/774-v5.15-1-igc-remove-_I_PHY_ID-checking.patch generic-backport/774-v5.15-2-igc-remove-phy-type-checking.patch All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.117John Audia2022-06-0615-93/+31
| | | | | | | | | | | | Removed upstreamed: backport-5.10/890-v5.19-net-sfp-Add-tx-fault-workaround-for-Huawei-MA5671A-SFP-ON.patch All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.116Hauke Mehrtens2022-06-068-92/+8
| | | | | | | | | | | | Removed upstreamed: generic/backport-5.10/900-regulator-consumer-Add-missing-stubs-to-regulator-co.patch All other patches automatically rebased. Compile-tested: lantiq/xrx200, armvirt/64 Run-tested: lantiq/xrx200, armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* realtek: add support for ZyXEL GS1900-24ERaylynn Knight2022-06-063-0/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24E * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB Macronix MX25L12835F * RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE * Ethernet: 24x 10/100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 24 ethernet port link/activity LEDs (green, SoC controlled) * Buttons: 1 "RESET" button on front panel * Switch: 1 Power switch on rear of device * Power 120-240V AC C13 * UART: 1 serial header (JP2) with populated standard pin connector on the left side of the PCB. Pinout (front to back): + Pin 1 - VCC marked with white dot + Pin 2 - RX + Pin 3 - TX + PIn 4 - GND Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware * Select the HTTP radio button * Select the Active radio button * Use the browse button to locate the realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin file and select open so File Path is updated with filename. * Select the Apply button. Screen will display "Prepare for firmware upgrade ...". *Wait until screen shows "Do you really want to reboot?" then select the OK button * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24E is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Raylynn Knight <rayknight@me.com>
* hostapd: drop wnm_disassoc_imminentStijn Tintel2022-06-061-45/+0
| | | | | | | | All known users of this ubus method have been updated to use the new bss_transition_request method instead. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: David Bauer <mail@david-bauer.net>
* ksmbd: update to 3.4.5Rosen Penev2022-06-052-101/+2
| | | | | | | | | | | Major changes are: Add support for smbd-direct multi-desctriptor. Add support for dkms. Add support for key exchange. Fix seveal bugs. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: allow use GPIO17 as regular gpio on GL-AR300M devicesPtilopsis Leucotis2022-06-051-3/+3
| | | | | | | | Small update to my previous path 'fix I2C on GL-AR300M devices'. This update allow using GPIO17 as regular GPIO in case it not used as I2C SDA line. Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
* ath79: ZTE MF286[,A,R]: use GPIO19 as ath9k LEDLech Perczak2022-06-051-14/+7
| | | | | | | | | | | | With the pinctrl configuration set properly by the previous commit, the LED stays lit regardless of status of 2.4GHz radio, even if 5GHz radio is disabled. Map GPIO19 as LED for ath9k, this way the LED will show activity for both bands, as it is bound by logical AND with output of ath10k-phy0 LED. This works well because during management traffic, phy*tpt triggers typically cause LEDs to blink in unison. Link: <https://github.com/openwrt/openwrt/pull/9941> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ZTE MF286[,A,R]: fix WLAN LED mappingLech Perczak2022-06-051-0/+8
| | | | | | | | | | The default configuration of pinctrl for GPIO19 set by U-boot was not a GPIO, but an alternate function, which prevented the GPIO hog from working. Set GPIO19 into GPIO mode to allow the hog to work, then the ath10k LED output can control the state of actual LED properly. Link: <https://github.com/openwrt/openwrt/pull/9941> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: add support for Linksys WHW01 v1Peter Adkins2022-06-058-5/+362
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331]. Specification ------------- SOC: Qualcomm IPQ4018 WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Ethernet: Qualcomm QCA8072 (2-port) SPI Flash 1: Mactronix MX25L1605D (2MB) SPI Flash 2: Winbond W25M02GV (256MB) DRAM: Nanya NT5CC128M16IP-DI (256MB) LED Controller: NXP PCA963x (I2C) Buttons: Single reset button (GPIO). Notes ----- There does not appear to be a way to trigger TFTP recovery without entering U-Boot. The device must be opened to access the serial console in order to first flash OpenWrt onto a device from factory. The device has automatic recovery backed by a second set of partitions on the larger of the two SPI flash ICs. Both the primary and secondary must be flashed to prevent accidental rollback to "factory" after 3 failed boot attempts. Serial console -------------- A serial console is available on the following pins of the populated J2 connector on the device mainboard (115200 8n1). (<-- Top of PCB / Device) J2 [o o o o o o] | | | | | `-- GND | `---- TX `--------- RX Installation instructions ------------------------- 1. Setup TFTP server with server IP set to 192.168.1.236. 2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Revert to "factory" ------------------- 1. Download latest firmware update from vendor support site. 2. Copy extracted `.img` file to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Link: https://github.com/openwrt/openwrt/pull/3682 Signed-off-by: Peter Adkins <peter@sunkenlab.com> (calibration from nvmem, updated to 5.10+5.15) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* generic: remove patch to fix vlan setup on mv88e6xxxJosef Schlehofer2022-06-051-27/+0
| | | | | | | | | | | | This patch was present in Linux kernel [1] since version 5.11rc1, but it was superseded by another patch, which set configure_vlan_while_not_filtering to true by default since kernel v5.12-rc2 [2]. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/net/dsa/mv88e6xxx/chip.c?h=v5.15.41&id=b8b79c414eca4e9bcab645e02cb92c48db974ce9 [2] https://github.com/torvalds/linux/commit/0ee2af4ebbe3c4364429859acd571018ebfb3424# Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-02-03 03:49:11 +0000